CYPRESS CY28341ZC-2

CY28341-2
Universal Clock Chip for VIA™P4M/KT/KM400
DDR Systems
Features
Table 1. Frequency Selection Table
FS(3:0)
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
• Supports VIA P4M/KM/KT/266/333/400 chipsets
• Supports Pentium® 4, Athlon™ processors
• Supports two DDR DIMMS
• Supports three SDRAM DIMMS at 100 MHz
• Provides:
— two different programmable CPU clock pairs
— six differential SDRAM DDR pairs
— three low-skew/-jitter AGP clocks
— seven low-skew/-jitter PCI clocks
— one 48M output for USB
— one programmable 24M or 48M for SIO
• Dial-a-Frequency and Dial-a-dB features
• Spread Spectrum for best electromagnetic interference
(EMI) reduction
• Watchdog feature for system recovery
CPU
66.80
100.00
120.00
133.33
72.00
105.00
160.00
140.00
77.00
110.00
180.00
166.6
90.00
100.00
200.00
133.33
AGP
66.80
66.80
60.00
66.67
72.00
70.00
64.00
70.00
77.00
73.33
60.00
66.6
60.00
66.67
66.67
66.67
PCI
33.40
33.40
30.00
33.33
36.00
35.00
32.00
35.00
38.50
36.67
30.00
33.3
30.00
33.33
33.33
33.33
• SMBus-compatible for programmability
• 56-pin SSOP and TSSOP packages
Block Diagram
Pin Configuration[1]
VDDR
XIN
REF(0:1)
XTAL
XOUT
REF0
FS0
FS2
VDDI
SELP4_K7#
CPUCS_T/C
VDDC
CPU(0:1)/CPU0D_T/C
PLL1
VDDPCI
PCI(3:6)
FS3 FS1
PCI1
VDDAGP
AGP(0:2)
SDATA
SCLK
SMBus
VDD48M
48M
PLL2
/2
WDEN
24_48M
SRESET#
VDDD
FBOUT
WD
SELSDR_DDR
Buf_IN
S2D
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
VTTPWRGD#/REF1
VDDR
VSSC
CPUT/CPUOD_T
CPUC/CPUOD_C
VDDC
VDDI
CPUCS_C
CPUCS_T
VSSI
FBOUT
BUF_IN
DDRT0/SDRAM0
DDRC0/SDRAM1
DDRT1/SDRAM2
DDRC1/SDRAM3
VDDD
VSSD
DDRT2/SDRAM4
DDRC2/SDRAM5
DDRT3/SDRAM6
DDRC3/SDRAM7
VDDD
VSSD
DDRT4/SDRAM8
DDRC4/SDRAM9
DDRT5/SDRAM10
DDRC5/SDRAM11
56 pin SSOP
DDRT(0:5)/SDRAM(0,2,4,6,8,10)
DDRC(0:5)/SDRAM(1,3,5,7,9,11)
CONVERT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
CY28341-2
PCI_F
MULTSEL
PCI2
PD#
*FS0/REF0
VSSR
XIN
XOUT
VDDAGP
AGP0
*SELP4_K7/AGP1
AGP2
VSSAGP
**FS1/PCI_F
**SELSDR_DDR/PCI1
*MULTSEL/PCI2
VSSPCI
PCI3
PCI4
VDDPCI
PCI5
PCI6
VSS48M
**FS3/48M
**FS2/24_48M
VDD48M
VDD
VSS
IREF
*PD#/SRESET#
SCLK
SDATA
Note:
1. Pins marked with [*] have internal pull-up resistors. Pins marked with [**] have internal pull-down resistors.
Cypress Semiconductor Corporation
Document #: 38-07471 Rev. *D
•
3901 North First Street
•
San Jose, CA 95134
•
408-943-2600
Revised March 11, 2005
CY28341-2
Pin Description[2]
Pin Number
Pin Name
PWR
I/O
Pin Description
I
Oscillator Buffer Input. Connect to a crystal or to an external clock.
VDD
O
Oscillator Buffer Output. Connect to a crystal. Do not connect when an
external clock is applied at XIN.
3
XIN
4
XOUT
1
FS0/REF0
VDDR
56
VTTPWRGD#
VDDR
I
If SELP4_K7 = 1, with a P4 processor set up as CPUT/C. At power-up,
VTT_PWRGD# is an input. When this input transitions to a logic low, the FS
(3:0) and MULTSEL are latched and all output clocks are enabled. After the
first high to low transition on VTT_PWRGD#, this pin is ignored and will not
effect the behavior of the device thereafter. When the VTT_PWRGD# feature
is not used, please connect this signal to ground through a 10KΩ resistor.
REF1
VDDR
O
If SELP4_K7 = 0, with an Athlon (K7) processor as CPU_OD(T:C).
VTT_PWRGD# function is disabled, and the feature is ignored. This pin
becomes REF1 and is a buffered copy of the signal applied at XIN.
44,42,38,
36,32,30
DDRT
(0:5)/SDRAM
(0,2,4,6,8,10)
VDDD
O
These pins are programmable through strapping pin11, SELSDR_DDR#.
If SELSDR_DDR#.= 0, these pins are configured for DDR clock outputs. They
are “True” copies of signal applied at Pin45, BUF_IN. In this mode, VDDD must
be 2.5VIf SelSDR_DDR#.= 1, these pins are configured for
SDRAM(0,2,4,6,8,10) single ended clock outputs, copies of (and in phase
with) signal applied at Pin45, BUF_IN. In this mode, VDDD must be 3.3V
43,41,37
35,31,29
DDRC
(0:5)/SDRAM
(1,3,5,7,9,11)
VDDD
O
These pins are programmable through strapping pin11, SELSDR_DDR#.
If SelSDR_DDR#.= 0, these pins are configured for DDR clock outputs. They
are “Complementary” copies of signal applied at Pin45, BUF_IN. In this mode,
VDDD must be 2.5VIf SelSDR_DDR#.= 1, these pins are configured for
SDRAM(1,3,5,7,9,11) single ended clock outputs, copies of (and in phase
with) signal applied at Pin45, BUF_IN. In this mode, VDDD must be 3.3V.
7
SELP4_K7 /
AGP1
VDDAGP I/O Power-on Bidirectional Input/Output. At power-up, SELP4_K7 is the input.
PU When the power supply voltage crosses the input threshold voltage,
SELP4_K7 state is latched and this pin becomes AGP1 clock output.
SELP4_K7 = 1, P4 mode. SELP4_K7 = 0, K7 mode.
12
MULTSEL/PCI2
VDDPCI
53
CPUT/CPUOD_T
VDDC
O
3.3V CPU Clock Outputs. This pin is programmable through strapping pin7,
SELP4_K7. If SELP4_K7 = 1, this pin is configured as the CPUT Clock Output.
If SELP4_K7 = 0, this pin is configured as the CPUOD_T Open Drain Clock
Output. See Table 1
52
CPUC/CPUOD_C
VDDC
O
3.3V CPU Clock Outputs. This pin is programmable through strapping pin7,
SELP4_K7. If SELP4_K7 = 1, this pin is configured as the CPUC Clock Output.
If SELP4_K7 = 0, this pin is configured as the CPUOD_C Open Drain Clock
Output. See Table 1
48,49
CPUCS_T/C
I/O Power-on Bidirectional Input/Output. At power-up, FS0 is the input. When
PU the power supply voltage crosses the input threshold voltage, FS0 state is
latched and this pin becomes REF0, buffered copy of signal applied at XIN.
(1-2 x strength, selectable by SMBus. Default value is 1 x strength.)
I/O Power-on Bidirectional Input/Output. At power-up, MULTSEL is the input.
PU When the power supply voltage crosses the input threshold voltage,
MULTSEL state is latched and this pin becomes PCI2 clock output. MULTSEL
= 0, Ioh is 4 x IREFMULTSEL = 1, Ioh is 6 x IREF
VDDI
O
2.5V CPU Clock Outputs for Chipset. See Table 1.
14,15,17,18 PCI (3:6)
VDDPCI
O
PCI Clock Outputs. Are synchronous to CPU clocks. See Table 1
10
FS1/PCI_F
VDDPCI
I/O Power-on Bidirectional Input/Output. At power-up, FS0 is the input. When
PD the power supply voltage crosses the input threshold voltage, FS1 state is
latched and this pin becomes PCI_F clock output.
20
FS3/48M
VDD48M I/O Power-on Bidirectional Input/Output. At power-up, FS3 is the input. When
PD the power supply voltage crosses the input threshold voltage, FS3 state is
latched and this pin becomes 48M, a USB clock output.
Note:
2. PU = internal pull-up. PD = internal pull-down. Typically = 250 kΩ (range 200 kΩ to 500 kΩ).
Document #: 38-07471 Rev. *D
Page 2 of 19
CY28341-2
Pin Description[2] (continued)
Pin Number
Pin Name
PWR
I/O
Pin Description
11
SELSDR_DDR#/
PCI1
VDDPCI
I/O Power-on Bidirectional Input/Output. At power-up, SELSDR_DDR is the
PD input. When the power supply voltage crosses the input threshold voltage,
SELSDR_DDR state is latched and this pin becomes PCI clock output.
SelSDR_DDR#.= 0, DDR Mode. SelSDR_DDR#.= 1, SDR Mode.
21
FS2/24_48M
VDD48M I/O Power-on Bidirectional Input/Output. At power-up, FS2 is the input. When
PD the power supply voltage crosses the input threshold voltage, FS2 state is
latched and this pin becomes 24_48M, a SIO programmable clock output.
6
AGP0
VDDAGP
O
AGP Clock Output. Is synchronous to CPU clocks. See Table 1
8
AGP2
VDDAGP
O
AGP Clock Output. Is synchronous to CPU clocks. See Table 1
25
IREF
I
Current reference programming input for CPU buffers. A precise resistor
is attached to this pin, which is connected to the internal current reference.
28
SDATA
27
SCLK
26
PD#/SRESET#
45
BUF_IN
If SelSDR_DDR#.= 0, 2.5V CMOS type input to the DDR differential
buffers. If SelSDR_DDR#.= 1, 3.3V CMOS type input to the SDR buffer.
46
FBOUT
If SelSDR_DDR#.= 0, 2.5V single ended SDRAM buffered output of the
signal applied at BUF_IN. It is in phase with the DDRT(0:5) signals.If
SelSDR_DDR#.= 1, 3.3V single ended SDRAM buffered output of the signal
applied at BUF_IN. It is in phase with the SDRAM(0:11) signals
5
VDDAGP
3.3V power supply for AGP clocks
51
VDDC
3.3V power supply for CPUT/C clocks
16
VDDPCI
3.3V power supply for PCI clocks
55
VDDR
3.3V power supply for REF clock
50
VDDI
2.5V power supply for CPUCS_T/C clocks
22
VDD_48M
3.3V power supply for 48M
23
VDD
3.3V Common power supply
34,40
VDDD
If SelSDR_DDR#.= 0, 2.5V power supply for DDR clocksIf
SelSDR_DDR#.= 1, 3.3V power supply for SDR clocks.
9
VSSAGP
Ground for AGP clocks
13
VSSPCI
Ground for PCI clocks
54
VSSC
Ground for CPUT/C clocks
33,39
VSSD
Ground for DDR clocks
19
VSS_48M
Ground for 48M clock
47
VSSI
Ground for ICPUCS_T/C clocks
2
VSSR
Ground for REF
24
VSS
Common Ground
Document #: 38-07471 Rev. *D
I/O Serial Data Input. Conforms to the Phillips I2C specification of a Slave
Receive/Transmit device. It is an input when receiving data. It is an open drain
output when acknowledging or transmitting data.
I
Serial Clock Input. Conforms to the Philips I2C specification.
I/O Power-down Input/System Reset Control Output. If Byte6 Bit7 = 0(default),
PU this pin becomes a SRESET# open drain output. See system reset description.
If Byte6Bit7 = 1, this pin becomes PD# input with an internal pull-up. When
PD# is asserted low, the device enters power down mode. See power
management function.
Page 3 of 19
CY28341-2
Power Management Functions
All clocks can be individually enabled or stopped via the
two-wire control interface. All clocks are stopped in the low
state. All clocks maintain a valid high period on transitions from
running to stop and on transitions from stopped to running
when the chip was not powered down. On power up, the VCOs
will stabilize to the correct pulse widths within about 0.5 ms.
Serial Data Interface
To enhance the flexibility and function of the clock synthesizer,
a two-signal serial interface is provided. Through the Serial
Data Interface, various device functions such as individual
clock output buffers, etc., can be individually enabled or
disabled.
The registers associated with the Serial Data Interface
initializes to their default setting upon power-up, and therefore
use of this interface is optional. Clock device register changes
are normally made upon system initialization, if any are
required. The interface can also be used during system
operation for power management functions.
Data Protocol
The clock driver serial protocol accepts byte write, byte read,
block write, and block read operation from the controller. For
block write/read operation, the bytes must be accessed in
sequential order from lowest to highest byte (most significant
bit first) with the ability to stop after any complete byte has
been transferred. For byte write and byte read operations, the
system controller can access individual indexed bytes. The
offset of the indexed byte is encoded in the command code,
as described in Table 2.
The block write and block read protocol is outlined in Table 3
while Table 4 outlines the corresponding byte write and byte
read protocol.The slave receiver address is 11010010 (D2h).
Table 2. Command Code Definition
Bit
7
(6:0)
Description
0 = Block read or block write operation.
1 = Byte read or byte write operation
Byte offset for byte read or byte write operation.
For block read or block write operations, these bits
should be ‘0000000’
Table 3. Block Read and Block Write Protocol
Block Write Protocol
Bit
1
2:8
Description
Start
Slave address – 7 bits
Block Read Protocol
Bit
1
2:8
Description
Start
Slave address – 7 bits
9
Write
9
Write
10
Acknowledge from slave
10
Acknowledge from slave
11:18
19
20:27
28
29:36
37
38:45
Command Code – 8-bit ‘00000000’ stands for
block operation
11:18
Command Code – 8-bit ‘00000000’ stands for
block operation
Acknowledge from slave
19
Acknowledge from slave
Byte Count – 8 bits
20
Repeat start
Acknowledge from slave
Data byte 0 – 8 bits
Acknowledge from slave
Data byte 1 – 8 bits
46
Acknowledge from slave
....
Data Byte N/Slave Acknowledge...
....
Data Byte N – 8 bits
....
Acknowledge from slave
....
Stop
Document #: 38-07471 Rev. *D
21:27
Slave address – 7 bits
28
Read
29
Acknowledge from slave
30:37
38
39:46
47
48:55
Byte count from slave – 8 bits
Acknowledge
Data byte from slave – 8 bits
Acknowledge
Data byte from slave – 8 bits
56
Acknowledge
....
Data bytes from slave/Acknowledge
....
Data byte N from slave – 8 bits
....
Not Acknowledge
....
Stop
Page 4 of 19
CY28341-2
Table 4. Byte Read and Byte Write Protocol
Byte Write Protocol
Bit
Byte Read Protocol
Description
1
Bit
Start
2:8
1
Slave address – 7 bits
9
2:8
Write
10
Acknowledge from slave
11:18
19
20:27
Command Code – 8-bit ‘1xxxxxxx’ stands for byte
operationbit[6:0] of the command code represents the offset of the byte to be accessed
Description
Start
Slave address – 7 bits
9
Write
10
Acknowledge from slave
11:18
Command Code – 8-bit ‘1xxxxxxx’ stands for byte
operationbit[6:0] of the command code represents the offset of the byte to be accessed
Acknowledge from slave
19
Acknowledge from slave
Byte Count – 8 bits
20
Repeat start
28
Acknowledge from slave
29
stop
21:27
Slave address – 7 bits
28
Read
29
Acknowledge from slave
30:37
Data byte from slave – 8 bits
38
Not Acknowledge
39
stop
Serial Control Registers
Byte 0: Frequency Select Register
Bit
@Pup
Pin#
Name
Reserved
Description
7
0
6
H/W Setting
21
FS2
Reserved
5
H/W Setting
10
FS1
For Selecting Frequencies in Frequency Selection Table on page 1
4
H/W Setting
1
FS0
For Selecting Frequencies in Frequency Selection Table on page 1
3
0
2
H/W Setting
11
1
H/W Setting
20
FS3
For Selecting frequencies in Frequency Selection Table on page 1
0
H/W Setting
7
SELP4_K7
Only for reading the hardware setting of the CPU interface mode,
status of SELP4_K7# strapping.
For Selecting Frequencies in Frequency Selection Table on page 1
If this bit is programmed to “1”, it enables WRITE to bits (6:4,1) for
selecting the frequency via software (SMBus)
If this bit is programmed to a “0” it enable only READ of bits (6:4,1),
which reflect the hardware setting of FS(0:3).
SELSDR_DDR Only for reading the hardware setting of the SDRAM interface mode,
status of SELSDR_DDR# strapping.
Byte 1: CPU Clocks Register
Bit
7
@Pup
0
6
1
Pin#
MODE
Name
Description
0 = Down Spread. 1 = Center Spread. See Table 9 on page 9
SSCG
1 = Enable (default). 0 = Disable
5
1
SST1
Select spread bandwidth. See Table 9 on page 9
4
1
SST0
Select spread bandwidth. See Table 9 on page 9
3
1
48,49 CPUCS_T, CPUCS_C
1 = Output enabled (running). 0 = Output disabled asynchronously in a low
state.
2
1
53,52 CPUT/CPUOD_T
CPUC/CPUOD_C
1 = Output enabled (running). 0 = Output disable.
1
1
53,52 CPUT/C
In K7 mode, this bit is ignored.In P4 mode, 0 = when PD# asserted LOW,
CPUT stops in a high state, CPUC stops in a low state. In P4 mode, 1 = when
PD# asserted LOW, CPUT and CPUC stop in High-Z.
0
1
11
MULT0
Document #: 38-07471 Rev. *D
Only for reading the hardware setting of the Pin11 MULT0 value.
Page 5 of 19
CY28341-2
Byte 2: PCI Clock Register
Bit
@Pup
Pin#
Name
Description
7
0
PCI_DRV
PCI clock output drive strength 0 = Low strength, 1 = High strength
6
1
10
PCI_F
1 = Output enabled (running). 0 = Output disabled asynchronously in a low state.
5
1
18
PCI6
1 = Output enabled (running). 0 = Output disabled asynchronously in a low state.
4
1
17
PCI5
1 = Output enabled (running). 0 = Output disabled asynchronously in a low state.
3
1
15
PCI4
1 = Output enabled (running). 0 = Output disabled asynchronously in a low state.
2
1
14
PCI3
1 = Output enabled (running). 0 = Output disabled asynchronously in a low state.
1
1
12
PCI2
1 = Output enabled (running). 0 = Output disabled asynchronously in a low state.
0
1
11
PCI1
1 = Output enabled (running). 0 = Output disabled asynchronously in a low state.
Byte 3: AGP/Peripheral Clocks Register
Bit
@Pup
Pin#
7
0
21
Name
Description
24_48M
0 = pin21 output is 24 MHz. Writing a '1' into this register asynchronously
changes the frequency at pin21 to 48 MHz.
6
1
20
48MHz
1 = Output enabled (running). 0 = Output disabled asynchronously in a low state.
5
1
21
24_48M
1 = Output enabled (running). 0 = Output disabled asynchronously in a low state.
4
0
6,7,8
DASAG1
3
0
6,7,8
DASAG0
Programming these bits allow shifting skew of the AGP(0:2) signals relative to
their default value. See Table 5.
2
1
8
AGP2
1 = Output enabled (running). 0 = Output disabled asynchronously in a low state.
1
1
7
AGP1
1 = Output enabled (running). 0 = Output disabled asynchronously in a low state.
0
1
6
AGP0
1 = Output enabled (running). 0 = Output disabled asynchronously in a low state.
Table 5. Dial-a-Skew AGP(0:2)
DASAG (1:0)
AGP(0:2) Skew Shift
00
Default
01
–280 ps
10
+280 ps
11
+480 ps
Byte 4: Peripheral Clocks Register
Bit
@Pup
Pin#
Name
Description
7
1
20
48M
1 = Low strength, 0 = High strength
1 = strength x 1. 0= strength x 2
6
1
21
24_48M
1 = Low strength, 0 = High strength
1 = strength x 1. 0= strength x 2
5
0
6,7,8
DARAG1
4
0
6,7,8
DARAG0
Programming these bits allow modifying the frequency ratio of the AGP(2:0),
PCI(6:1, F) clocks relative to the CPU clocks. See Table 6.
3
1
1
REF0
1 = Output enabled (running). 0 = Output disabled asynchronously in a low state.
2
1
56
REF1
1 = Output enabled (running). 0 = Output disabled asynchronously in a low state.
1
1
1
REF0
1 = Low strength, 0 = High strength
0
1
56
REF1
1 = Low strength, 0 = High strength (K7 Mode only)
Table 6. Dial-A-Ratio AGP(0:2)
DARAG (1:0)
CU/AGP Ratio
00
Frequency Selection Default
01
2/1
10
2.5/1
11
3/1
Document #: 38-07471 Rev. *D
Page 6 of 19
CY28341-2
Byte 5: SDR/DDR Clock Register
Bit @Pup Pin#
45
Name
Description
7
0
BUF_IN threshold voltage DDR Mode, BUF_IN threshold setting. 0 = 1.15V, 1 = 1.05VSDR Mode, BUF_IN
threshold setting. 0 = 1.35V, 1 = 1.25V
6
1
5
1
29,30 DDRT/C5/SDRAM(10,11) 1 = Output enabled (running). 0 = Output disabled asynchronously in a low state.
4
1
31,32
DDRT/C4/SDRAM(8,9)
1 = Output enabled (running). 0 = Output disabled asynchronously in a low state.
3
1
35,36
DDRT/C3/SDRAM(6,7)
1 = Output enabled (running). 0 = Output disabled asynchronously in a low state.
2
1
37,38
DDRT/C2/SDRAM(4,5)
1 = Output enabled (running). 0 = Output disabled asynchronously in a low state.
1
1
41,42
DDRT/C1/SDRAM(2,3)
1 = Output enabled (running). 0 = Output disabled asynchronously in a low state.
0
1
43,44
DDRT/C0/SDRAM(0,1)
1 = Output enabled (running). 0 = Output disabled asynchronously in a low state.
46
FBOUT
1 = Output enabled (running). 0 = Output disabled asynchronously in a low state.
Byte 6: Watchdog Register
Bit @Pup Pin#
7
0
6
26
Name
Description
SRESET#
1 = Pin 26 is the input pin as PD# signal. 0 = Pin 26 is the output pin as SRESET#
signal.
0
Frequency Revert
This bit allows setting the Revert Frequency once the system is rebooted due to
Watchdog time out only.0 = selects frequency of existing H/W setting1 = selects
frequency of the second to last S/W setting. (the software setting prior to the one that
caused a system reboot).
5
0
WDTEST
For IMI Test - WD-Test, ALWAYS program to '0'
4
0
WD Alarm
This bit is set to “1” when the Watchdog times out. It is reset to “0” when the system
clears the WD time stamps (WD3:0).
3
0
WD3
This bit allows the selection of the time stamp for the Watchdog timer. See Table 7
2
0
WD2
This bit allows the selection of the time stamp for the Watchdog timer. See Table 7
1
0
WD1
This bit allows the selection of the time stamp for the Watchdog timer. See Table 7
0
0
WD0
This bit allows the selection of the time stamp for the Watchdog timer. See Table 7
Table 7. Watchdog Time Stamp
WD3
WD2
WD1
WD0
0
0
0
0
Off
FUNCTION
0
0
0
1
1 second
0
0
1
0
2 seconds
0
0
1
1
3 seconds
0
1
0
0
4 seconds
0
1
0
1
5 seconds
0
1
1
0
6 seconds
0
1
1
1
7 seconds
1
0
0
0
8 seconds
1
0
0
1
9 seconds
1
0
1
0
10 seconds
1
0
1
1
11 seconds
1
1
0
0
12 seconds
1
1
0
1
13 seconds
1
1
1
0
14 seconds
1
1
1
1
15 seconds
Byte 7: Dial-a-Frequency Control Register N
Bit
@Pup
Pin#
Document #: 38-07471 Rev. *D
Name
Description
Page 7 of 19
CY28341-2
Byte 7: Dial-a-Frequency Control Register N
7
0
Reserved
Reserved for device function test.
6
0
N6, MSB
5
0
N5
4
0
N4
3
0
N3
These bits are for programming the PLL’s internal N register. This access
allows the user to modify the CPU frequency at very high resolution
(accuracy). All other synchronous clocks (clocks that are generated from
the same PLL, such as PCI) remain at their existing ratios relative to the
CPU clock.
2
0
N2
1
0
N3
0
0
N0, LSB
Byte 8: Silicon Signature Register (all bits are read-only)
Bit
@Pup
Pin#
Name
Description
7
0
Revision_ID3
Revision ID bit [3]
6
0
Revision_ID2
Revision ID bit [2]
5
0
Revision_ID1
Revision ID bit [1]
4
1
Revision_ID0
Revision ID bit [0]
3
1
Vendor_ID3
Cypress's Vendor ID bit [3].
2
0
Vendor_ID2
Cypress's Vendor ID bit [2].
1
0
Vendor_ID1
Cypress's Vendor ID bit [1].
0
0
Vendor_ID0
Cypress's Vendor ID bit [0].
Byte9: Dial-A-Frequency Control Register R
Bit
@Pup
Pin#
Name
7
0
6
0
R5, MSB
5
0
R4
4
0
R3
3
0
R2
2
0
R1
1
0
R0
0
0
DAF_ENB
Description
Reserved
These bits are for programming the PLL’s internal R register. This access
allows the user to modify the CPU frequency at very high resolution
(accuracy). All other synchronous clocks (clocks that are generated from
the same PLL, such as PCI) remain at their existing ratios relative to the
CPU clock.
R and N register mux selection. 0 = R and N values come from the ROM.
1 = data is load from DAF (SMBus) registers.
Dial-a-Frequency Feature
SMBus Dial-a-Frequency feature is available in this device via
Byte7 and Byte9.
P is a PLL constant that depends on the frequency selection
prior to accessing the Dial-a-Frequency feature.
Table 8.
FS(4:0)
XXXXX
Document #: 38-07471 Rev. *D
P
96016000
Page 8 of 19
CY28341-2
Spread Spectrum Clock Generation (SSCG)
Spread Spectrum is enabled/disabled via SMBus register Byte
1, Bit 7.
Table 9. Spread Spectrum Table
Mode
SST1
SST0
% Spread
0
0
0
+0.14, –1.23
0
0
1
+0, –1.00
0
1
0
+0, –0.60
0
1
1
+0, –0.52
1
0
0
+0.72, –0.71
1
0
1
+0.47, –0.49
1
1
0
+0.34, –0.33
1
1
1
+0.30, –0.28
Swing Select Functions Through Hardware
MULTSEL
Board Target
Trace/Term Z
Reference R,
IREF = VDD/(3*Rr)
Output Current
VOH@Z
0
50 Ohm
Rr = 221 1%,
IREF = 5.00 mA
IOH = 4* Iref
1.0V@50
1
50 Ohm
Rr = 475 1%,
IREF = 2.32 mA
IOH = 6* Iref
0.7V@50
System Self Recovery Clock Management
This feature is designed to allow the system designer to
change frequency while the system is running and reboot the
operation of the system in case of a hang up due to the
frequency change.
When the system sends an SMBus command requesting a
frequency change through Byte 4 or through bytes 13 and 14,
it must have previously sent a command to byte 12, for
selecting which time out stamp the Watchdog must perform,
otherwise the System Self Recovery feature will not be applicable. Consequently, this device will change frequency and
then the Watchdog timer starts timing. Meanwhile, the system
BIOS is running its operation with the new frequency. If this
device receives a new SMBus command to clear the bits originally programmed in Byte 12, bits (3:0) (reprogram to 0000),
Document #: 38-07471 Rev. *D
before the Watchdog times out, then this device will keep
operating in its normal condition with the new selected
frequency. If the Watchdog times out the first time before the
new SMBus reprograms Byte 12, bits (3:0) to (0000), then this
device will send a low system reset pulse, on SRESET# (see
byte12, bit7), and changes WD alarm (Byte12, Bit4) status to
“1” then restarts the Watchdog timer again. If the Watchdog
times out a second time, then this device will send another low
pulse on SRESET#, will relatch original hardware strapping
frequency (or second to last software selected frequency, see
byte12, bit6) selection, set WD alarm bit (Byte12, bit4) to ‘1,’
then start WD timer again. The above-described sequence will
keep repeating until the BIOS clears the SMBus byte12 bits
(3:0). Once the BIOS sets Byte 12 bits (3:0) = 0000, then the
Watchdog timer is turned off and the WD alarm bit (Byte 12,
bit4) is reset to ‘0.’
Page 9 of 19
CY28341-2
S y s t e m r u n n in g w it h
o r ig in a lly s e le c t e d
f r e q u e n c y v ia
h a r d w a r e s t r a p p in g .
N o
F r e q u e n c y w ill c h a n g e b u t S y s t e m S e lf
R e c o v e r y n o t a p p lic a b le ( n o t im e s t a m p
s e le c t e d a n d b y t e 1 2 , b it ( 3 : 0 ) is s t ill =
"0 0 0 0 "
R e c e iv e F r e q u e n c y
C h a n g e R e q u e s t v ia
S M B u s B y t e 4 o r V ia D ia la -fre q u e n c y ?
Y e s
C h a n g e to a n e w
fre q u e n c y
N o
Is S M B u s B y te 9 , tim e o u t
s t a m p e n a b le d - ( b y t e 1 2 , b it
(3 :0 )
0 0 0 0 )?
1 ) S e n d a n o th e r 3 m S lo w p u ls e o n S
2 ) R e la t c h o r ig in a l h a r d w a r e s t r a p p in
f o r r e t u r n t o o r ig in a l f r e q u e n c y s e t t in g
3 ) S e t W D A la r m b it ( b y t e 1 2 , B it 4 ) t o
4 ) S ta r t W D tim e r
Y e s
R E S E T
g s e le c tio n
s .
"1 "
S t a r t in t e r n a l w a t c h d o g t im e r .
Y e s
W a t c h D o g t im e o u t ?
1 ) S e n d S R E S E T
p u ls e
2 ) S e t W D b it
( b y t e 1 2 , b it 4 ) t o '1 '
3 ) S t a r t W D t im e r
Y e s
W a t c h D o g t im e o u t ?
N o
N o
S M B u s b y te 1 2 tim e
o u t s t a m p d is a b le d ?
N o
S M B u s b y te 9 tim e o u t
s t a m p d is a b le d , B y t e
1 2 , b it ( 3 : 0 ) = ( 0 0 0 0 ) ?
N o
Y e s
Y e s
T u r n o ff w a tc h d o g tim e r .
K e e p n e w f r e q u e n c y s e t t in g . S e t W D
b it ( b y t e 1 2 , b it 4 ) t o ''0 '
a la r m
Figure 1. Watchdog Recovery Clock
P4 Processor SELP4_K7# = 1
Power-down Assertion (P4 Mode)
When PD# is sampled low by two consecutive rising edges of
CPU# clock then all clock outputs except CPU clocks must be
held low on their next high to low transition. CPU clocks must
be held with the CPU clock pin driven high with a value of 2 x
Iref, and CPU# undriven. Note that Figure 1 shows CPU =
133 MHz. This diagram and description are applicable for all
valid CPU frequencies 66, 100, 133, 200 MHz. Due to the state
of internal logic, stopping and holding the REF clock outputs
in the LOW state may require more than one clock cycle to
complete.
Power-down Deassertion (P4 Mode)
The power-up latency needs to less than 3 ms.
PW RDW N#
CPUT 133M Hz
CPUT# 133M Hz
PCI 33M Hz
AG P 66M Hz
USB 48M Hz
R E F 1 4 .3 1 8 M H z
DDRT 133M Hz
DDRC 133M Hz
SDRAM 133M Hz
Figure 2. Power-down Assertion Timing Waveform (in P4 mode)
Document #: 38-07471 Rev. *D
Page 10 of 19
CY28341-2
< 1 .5 m s e c
PW RDW N#
CPU 133MHz
CPU# 133MHz
PCI 33MHz
AG P 66MHz
USB 48MHz
R E F 1 4 .3 1 8 M H z
DDRT 133MHz
DDRC 133MHz
SDRAM 133MHz
Figure 3. Power-down Deassertion Timing Waveform (in P4 mode)
AMD K7 processor SELP4_K7# = 0
Power-down Assertion (K7 Mode)
When the PD# signal is asserted LOW, all clocks are disabled
to a low level in an orderly fashion prior to removing power
from the part. When PD# is asserted (forced) LOW, the device
transitions to a shutdown (power-down) mode and all power
supplies may then be removed. When PD# is sampled LOW
by two consecutive rising edges of CPU clock, then all affected
clocks are stopped in a LOW state as soon as possible. When
in power-down (and before power is removed), all outputs are
synchronously stopped in a LOW state (see Figure 3 below),
all PLL’s are shut off, and the crystal oscillator is disabled.
When the device is shut down, the I2C function is also
disabled.
PW RDW N#
C P U O D _T 133M H z
C P U C S _T 133M H z
C P U O D _C 133M H z
C P U C S _C 133M H z
P C I 33M H z
A G P 66M H z
U S B 48M H z
R E F 14.318M H z
D D R T 133M H z
D D R C 133M H z
S D R A M 133M H z
Figure 4. Power-down Assertion Timing Waveform (in K7 mode)
Document #: 38-07471 Rev. *D
Page 11 of 19
CY28341-2
Power-down Deassertion (K7 Mode)
When deasserted PD# to HIGH level, all clocks are enabled
and start running on the rising edge of the next full period in
order to guarantee a glitch-free operation, no partial clock
pulses.
< 1 .5 m se c
PW RDW N#
CPU 133MHz
CPU# 133MHz
PCI 33MHz
AGP 66MHz
USB 48MHz
R E F 1 4 .3 1 8 M H z
DDRT 133MHz
DDRC 133MHz
SDRAM 133MHz
Figure 5. Power-down Deassertion Timing Waveform (in K7 Mode)
VID (0:3),
SEL (0,1)
VTT_PW RGD#
PW RGD
0.2-0.3m S
Delay
VDD Clock Gen
Clock State
Clock Outputs
Clock VCO
State 0
W ait for
VTT_GD#
State 1
State 2
Off
Off
Sam ple Sels
State 3
On
(Note A)
On
Figure 6. VTT_PWGD# Timing Diagram (With Advanced PIII Processor SelP4_K7 = 1)[3]
Note:
3. This time diagram shows that VTT_PWRGD# transits to a logic low in the first time at power-up. After the first high-to-low transition of VTT_PWRGD#, device is
not affected, VTT_PWRGD# is ignored.
Document #: 38-07471 Rev. *D
Page 12 of 19
W
RG
D#
ow
CY28341-2
D e la y 0 .2 5 m S
S2
=L
VT
TP
S1
W a it f o r
1 .1 4 6 m s
S a m p le
In p u ts
F S ( 3 :0 )
E n a b le
O u tp u te s
V D D A = 2 .0 V
S0
S3
P o w e r O ff
N o rm a l
O p e r a tio n
V D D 3 .3 = O f f
Figure 7. Clock Generator Power-up/Run State Diagram (with P4 processor SELP4_K7#=1)
Connection Circuit DDRT/C Signals
For open-drain CPU output signals (with K7 processor SELP4_K7#=0)
150 Ohm
CPUOD_T
47 Ohm
VDDCPU(1.5V)
VDDCPU(1.5V)
3.3V
60.4 Ohm
52 Ohm 5"
500 Ohm
680 pF
3.3V
CPUOD_C
47 Ohm
Measurement Point
52 Ohm 1"
500 Ohm
20 pF
301 Ohm
150 Ohm
52 Ohm 5"
VDDCPU(1.5V)
52 Ohm 1"
500 Ohm
680 pF
60.4 Ohm
500 Ohm
Measurement Point
20 pF
VDDCPU(1.5V)
Figure 8. K7 Load Termination
6”
6”
Table 10.Signal Loading Table
Clock Name
REF (0:1), 48MHz (USB), 24_48MHz
AGP(0:2), SDRAM (0:11)
PCI_F(0:5)
DDRT/C (0:5), FBOUT
CPUT/C
CPUOD_T/C
CPUCS_T/C
Document #: 38-07471 Rev. *D
Figure 9. CS Load Termination
Max Load (in pF)
20
30
30
For Differential CPU Output Signals (with P4 Processor
SELP4_K7= 1)
The following diagram shows lumped test load configurations
for the differential Host Clock outputs.
See Figure 10
See Figure 8
See Figure 9
Page 13 of 19
CY28341-2
CLK Measurement Point
T PCB
CPUT
RtA1
RLA1
RtB1
R LB1
CLA
RD
MULTSEL
CLK Measurement Point
T PCB
CPUT#
RtA2
RLA2
RtB2
R LB2
CLB
Rref
Figure 10. P4 Load Termination
Table 11.Lumped Test Load Configuration
Component
0.7V Amplitude Value
1.0V Amplitude Value
RtA1, RtA2
33Ω
0Ω
RLA1, RLA2
49.9Ω
∞
TPCB
3” 50 ΩZ
3” 50 ΩZ
RLB1, RLB2
∞
63Ω
RD
∞
470Ω
RtB1, RtB2
0Ω
33Ω
CLA, CLB
2 pF
2 pF
Rref
475Ω w/mult0 = 1
221Ω w/mult0 = 0
Group Timing Relationships and Tolerances[4]
Offset (ps)
tCSAGP
CPUCS to AGP
tAP
AGP to PCI
0ns
Tolerance (ps)
Conditions
750
500
CPUCS Leads
1,250
500
AGP Leads
10ns
20ns
30ns
CPU CLOCK 66.6MHz
CPU CLOCK 100MHz
CPU CLOCK 133.3MHz
tCSAGP
AGP CLOCK 66.6MHz
tAP
PCI CLOCK 33.3MHz
Note:
4. Ideally the probes should be placed on the pins. If there is a transmission line between the test point and the pin for one signal of the pair (e.g., CPU), the same
length transmission line should be added to the other signal of the pair (e.g., AGP).
Document #: 38-07471 Rev. *D
Page 14 of 19
CY28341-2
Maximum Ratings[5]
Storage Temperature: ................................ –65°C to + 150°C
This device contains circuitry to protect the inputs against
damage due to high static voltages or electric field. However,
precautions should be take to avoid application of any voltage
higher than the maximum rated voltages to this circuit. For
proper operation, VIN and VOUT should be constrained to the
range:
Operating Temperature: .................................... 0°C to +70°C
VSS < (VIN or VOUT) < VDD.
Input Voltage Relative to VSS:.............................. VSS – 0.3V
Input Voltage Relative to VDDQ or AVDD: ............. VDD + 0.3V
Maximum ESD .............................................................2000V
Unused inputs must always be tied to an appropriate logic
voltage level (either VSS or VDD).
Maximum Power Supply: ................................................5.5V
DC Parameters (VDD = VDDPCI = VDDAGP = VDDR = VDD48M = VDDC = 3.3V±5%, VDDI = VDD = 2.5±5%, TA = 0°C TO +70°C)
Parameter
VIL1
VIH1
VIL2
VIH2
VOL
IOL
IOZ
IDD3.3V
IDD2.5V
IPD
IPUP
IPDWN
CIN
COUT
LPIN
CXTAL
Description
Input Low Voltage
Input High Voltage
Input Low Voltage
Input High Voltage
Output Low Voltage for SRESET#
Pull-down current for SRESET#
Three-state leakage Current
Dynamic Supply Current
Dynamic Supply Current
Power-down Supply current
Internal Pull-up Device Current
Internal Pull-down Device Current
Input Pin Capacitance
Output Pin Capacitance
Pin Inductance
Crystal Pin Capacitance
Conditions
Applicable to PD#, F S(0:4)
Min.
Typ.
Max.
0.8
2.0
Applicable to SDATA and SCLK
1.0
2.2
0.4
24
IOL
VOL = 0.4V
35
CPU frequency set at 133.3 MHz, Note 6
CPU frequency set at 133.3 MHz, Note 6
PD# = 0
Input @ VSS
Input @ VDD
Measured from the Xin or Xout to VSS
10
190
195
600
–25
10
5
6
7
45
150
175
95
27
36
Unit
Vdc
Vdc
Vdc
Vdc
V
mA
µA
mA
mA
µA
µA
µA
pF
pF
pF
pF
AC Parameters
Parameter
Description
XTAL
TDC
Xin Duty Cycle
Xin Period
TPERIOD
Xin High Voltage
VHIGH
Xin Low Voltage
VLOW
Xin Rise and Fall Times
TR/TF
Xin Cycle to Cycle Jitter
TCCJ
Crystal Start-up Time
TXS
P4 Mode CPU at 0.7V
TDC
CPUT/C Duty Cycle
CPUT/C Period
TPERIOD
100 MHz
Min.
Max.
133 MHz
Min.
Max
200 MHz
Min.
Max.
45
69.84
0.7VDD
0
55
71.00
VDD
.3VDD
10.0
500
30
45
69.84
0.7VDD
0
55
71.0
VDD
.3VDD
10
500
30
45
69.84
0.7VDD
0
55
71.0
VDD
.3VDD
10
500
30
45
9.85
55
10.2
45
7.35
55
7.65
45
4.85
55
5.1
Unit
%
ns
V
V
ns
ps
ms
Notes
7,14
7,14
12
15
13
8,11
10,12
% 7,8,9,15,16
ns 7,8,9,15,16
Notes:
5. Multiple Supplies: The voltage on any input or I/O pin cannot exceed the power pin during power-up. Power supply sequencing is NOT required.
6. All outputs loaded as per maximum capacitive load table.
7. This parameter is measured as an average over a 1-us duration, with a crystal center frequency of 14.31818 MHz.
8. All outputs loaded as per loading specified in theTable 11.
9. Probes are placed on the pins, and measurements are acquired at 1.5V for 3.3V signals and at 1.25V for 2.5V, and 50% point for differential signals.
10. Probes are placed on the pins, and measurements are acquired at 0.4V.
11. When Xin is driven from and external clock source (3.3V parameters apply).
12. When crystal meets minimum 40-ohm device series resistance specification.
13. Measured between 0.2VDD and.7VDD.
14. This is required for the duty cycle on the REF clock out to be as specified. The device will operate reliably with input duty cycles up to 30/70 but the REF clock
duty cycle will not be within data sheet specifications.
15. Measured at VX, or where subtraction of CLK-CLK# crosses 0V.
16. See Figure 10 for 0.7V loading specification.
Document #: 38-07471 Rev. *D
Page 15 of 19
CY28341-2
AC Parameters (continued)
100 MHz
133 MHz
Parameter
Description
Min.
Max.
Min.
Max
TR/TF
CPUT/C Rise and Fall Times
175
700
175
700
Rise/Fall Matching
20%
20%
Rise/Fall Time Variation
125
125
∆ TR/TF
CPUCS_T/C to CPUT/C Clock Skew
0
200
0
150
TSKEW
TCCJ
CPUT/C Cycle to Cycle Jitter
–150
+150
–150
+150
Crossing Point Voltage at 0.7V Swing 280
430
280
430
VCROSS
P4 Mode CPU at 1.0V
TDC
CPUT/C Duty Cycle
45
55
45
55
TPERIOD
CPUT/C Period
9.85
10.2
7.35
7.65
CPUT/C Rise and Fall times
175
467
175
467
Differential
TR/TF
TSKEW
CPUCS_T/C to CPUT/C Clock Skew
0
200
0
150
CPUT/C Cycle to Cycle Jitter
–150
+150
–150
+150
TCCJ
Crossing Point Voltage at 1V Swing
510
760
510
760
VCROSS
SE-DeltaSlew Absolute Single-ended Rise/Fall
325
325
Waveform Symmetry
K7 Mode
TDC
CPUOD_T/C Duty Cycle
45
55
45
55
TPERIOD
CPUOD_T/C Period
9.98
10.5
7.5
8.0
CPUOD_T/C Low Time
2.8
1.67
TLOW
CPUOD_T/C Fall Time
0.4
1.6
0.4
1.6
TF
TSKEW
CPUCS_T/C to CPUT/C Clock Skew
0
200
0
150
CPUOD_T/C Cycle-to-Cycle Jitter
–150
+150
–150
+150
TCCJ
Differential Voltage AC
0.4
Vp+0.6V
0.4 Vp+0.6V
VD
VX
Differential Crossover Voltage
500
1100
500
1100
CHIPSET CLOCK
TDC
CPUCS_T/C Duty Cycle
45
55
45
55
CPUCS_T/C Period
10.0
10.5
15
15.5
TPERIOD
TR / TF
CPUCS_T/C Rise and Fall Times
0.4
1.6
0.4
1.6
Differential Voltage AC
0.4
Vp+.06V
0.4 Vp+.06V
VD
Differential Crossover Voltage
0.5*VDDI 0.5*VDDI 0.5*VD 0.5*VDDI
VX
–0.2
+0.2
+0.2
DI–0.2
AGP
TDC
AGP(0:2) Duty Cycle
45
55
45
55
AGP(0:2) Period
15
16
15
16
TPERIOD
AGP(0:2) High Time
5.25
5.25
THIGH
AGP(0:2) Low Time
5.05
5.05
TLOW
AGP(0:2) Rise and Fall Times
0.4
1.6
0.4
1.6
TR / TF
200 MHz
Min.
Max.
175
700
20%
125
0
200
–200
+200
280
430
Unit
Notes
ps 24
24,26
ps 8,24,16
ps 8,18,15,16
ps 8,18,15,16
mV 16
45
4.85
175
55
5.1
467
% 8,9,15
nS 8,9,15
ps 7,14,27
0
–200
510
200
+200
760
325
0
ps
mV
ps
8,14,11
8,14,11
27
26
45
55
%
5
5.5
ns
2.8
ns
0.4
1.6
ns
0
200
0
–200
+200
ps
0.4 Vp+.06V V
500
1100 mV
8,9
8,9
8,9
8,13
8,14,11
8,9
23
23
45
55
%
10.0
10.5
ns
0.4
1.6
ns
.4
Vp+.06V V
0.5*VD 0.5*VDDI V
+0.2
DI–0.2
45
15
5.25
5.05
0.4
55
16
1.6
%
ns
ns
ns
ns
7,8,9
7,8,9
7,8,13
24
11
7,8,9
7,8,9
8,21
8,10
8,13
Notes:
17. Probes are placed on the pins, and measurements are acquired between 0.4V and 2.4V for 3.3V signals and between 0.4V and 2.0V for 2.5V signals, and between
20% and 80% for differential signals.
18. This measurement is applicable with Spread ON or spread OFF.
19. Probes are placed on the pins, and measurements are acquired at 2.4V for 3.3V signals and at 2.0V for 2.5V signals).
20. Time specified is measured from when all VDDs reach their respective supply rail (3.3V and 2.5V) till frequency output is stable and operating within specs.
21. The typical value of VX is expected to be 0.5*VDDD (or 0.5*VDDC for CPUCS signals) and will track the variations in the DC level of the same.
22. VD is the magnitude of the difference between the measured voltage level on a DDRT (and CPUCS_T) clock and the measured voltage level on its complementary
DDRC (and CPUCS_C) one.
23. Measured at VX between the rising edge and the following falling edge of the signal.
24. Measured from VOL = 0.175V to VOH = 0.525V.
25. Measurement taken from differential waveform, from –0.35V to +0.35V.
26. Measurements taken from common mode waveforms, measure rise/fall time from 0.41V to 0.86V. Rise/fall time matching is defined as “the instantaneous
difference between maximum clk rise (fall) and minimum clk# fall (rise) time, or minimum clk rise (fall) and maximum clk# fall (rise) time”. This parameter is
designed for waveform symmetry.
27. Measured in absolute voltage, i.e., single-ended measurement.
Document #: 38-07471 Rev. *D
Page 16 of 19
CY28341-2
AC Parameters (continued)
Parameter
TSKEW
TCCJ
PCI
TDC
TPERIOD
THIGH
TLOW
TR / TF
TSKEW
TCCJ
48 MHz
TDC
TPERIOD
TR / TF
TCCJ
24 MHz
TDC
TPERIOD
TR / TF
TCCJ
REF
TDC
TPERIOD
TR / TF
TCCJ
Description
Any AGP to Any AGP Clock Skew
AGP(0:2) Cycle-to-Cycle Jitter
PCI(_F,1:6) Duty Cycle
PCI(_F,1:6) Period
PCI(_F,1:6) High Time
PCI(_F,1:6) Low Time
PCI(_F,1:6) Rise and Fall Times
Any PCI to Any PCI Clock Skew
PCI(_F,1:6) Cycle-to-Cycle Jitter
100 MHz
Min.
Max.
250
500
133 MHz
Min.
Max
250
500
200 MHz
Min.
Max.
250
500
45
30.0
12.0
12.0
0.5
45
30.0
12.0
12.0
0.5
45
30.0
12.0
12.0
0.5
55
2.5
500
500
55
2.5
500
500
55
2.5
500
500
Unit
Notes
ps 8,14
ps 8,9,14
%
ns
ns
ns
ns
ps
ps
7,8,9
7,8,9
8,21
8,10
8,13
8,14
8,9,14
48-MHz Duty Cycle
48-MHz Period
48-MHz Rise and Fall Times
48-MHz Cycle-to-Cycle Jitter
45
20.8299
1.0
55
20.8333
4.0
500
45
55
45
55
20.8299 20.8333 20.8299 20.8333
1.0
4.0
1.0
4.0
500
500
%
ns
ns
ps
7,8,9
7,8,9
8,13
8,9,14
24-MHz Duty Cycle
24-MHz Period
24-MHz Rise and Fall Times
24-MHz Cycle-to-Cycle Jitter
45
41.660
1.0
55
41.667
4.0
500
45
41.660
1.0
55
41.667
4.0
500
45
41.660
1.0
55
41.667
4.0
500
%
ns
ns
ps
7,8,9
7,8,9
8,13
8,9,14
REF Duty Cycle
REF Period
REF Rise and Fall Times
REF Cycle-to-Cycle Jitter
45
69.8413
1.0
55
71.0
4.0
1000
45
69.8413
1.0
55
71.0
4.0
1000
45
69.8413
1.0
55
71.0
4.0
1000
%
ns
ns
ps
7,8,9
7,8,9
8,13
8,9,14
VX
Crossing Point Voltage of DDRT/C
VD
Differential Voltage Swing
TDC
TPERIOD
TR / TF
TSKEW
TCCJ
THPJ
TDELAY
TSKEW
TSTABLE
DDRT/C(0:5) Duty Cycle
DDRT/C(0:5) Period
DDRT/C(0:5) Rise/Fall Slew Rate
DDRT/C to any DDRT/C Clock Skew
DDRT/C(0:5) Cycle-to-Cycle Jitter
DDRT/C(0:5) Half-period Jitter
BUF_IN to Any DDRT/C Delay
FBOUT to Any DDRT/C Skew
All-Clock Stabilization from Power-up
0.5*VDDD 0.5*VDDD 0.5*VDD 0.5*VDD 0.5*VDD 0.5*VDD V 15
–0.2
+0.2
D–0.2
D+0.2
D–0.2
D+0.2
0.7
VDDD +
0.7
VDDD +
0.7
VDDD + V 23
0.6
0.6
0.6
45
55
45
55
45
55
% 11
9.85
10.2
14.85
15.3
9.85
10.2
ns 11
1
3
1
3
1
3
V/ns 13
100
100
100
ps 8,14,11
±75
±75
±75
ps 8,14,11
±100
±100
±100
ps 8,14,11
1
4
1
4
1
4
ns 8,9
100
100
100
ps 8,9
3
3
3
ms 22
DDR
Ordering Information
Part Number
CY28341OC–2
CY28341OC–2T
CY28341ZC–2
CY28341ZC–2T
Lead-free
CY28341OXC–2
CY28341OXC–2T
Package Type
56-pin Shrunk Small Outline package (SSOP)
56-pin Shrunk Small Outline package (SSOP)–Tape and Reel
56-pin Thin Shrunk Small Outline package (TSSOP)
56-pin Thin Shrunk Small Outline package (TSSOP)–Tape and Reel
Product Flow
Commercial, 0° to 70°C
Commercial, 0° to 70°C
Commercial, 0° to 70°C
Commercial, 0° to 70°C
56-pin Shrunk Small Outline package (SSOP)
56-pin Shrunk Small Outline package (SSOP)–Tape and Reel
Commercial, 0° to 70°C
Commercial, 0° to 70°C
Document #: 38-07471 Rev. *D
Page 17 of 19
CY28341-2
Package Drawing and Dimensions
56-Lead Thin Shrunk Small Outline Package, Type II (6 mm x 12 mm) Z56
0.249[0.009]
28
1
DIMENSIONS IN MM[INCHES] MIN.
MAX.
REFERENCE JEDEC MO-153
7.950[0.313]
8.255[0.325]
PACKAGE WEIGHT 0.42gms
5.994[0.236]
6.198[0.244]
PART #
Z5624 STANDARD PKG.
ZZ5624 LEAD FREE PKG.
29
56
13.894[0.547]
14.097[0.555]
1.100[0.043]
MAX.
GAUGE PLANE
0.25[0.010]
0.20[0.008]
0.851[0.033]
0.950[0.037]
0.500[0.020]
BSC
0.170[0.006]
0.279[0.011]
0.051[0.002]
0.152[0.006]
0°-8°
SEATING
PLANE
0.508[0.020]
0.762[0.030]
0.100[0.003]
0.200[0.008]
51-85060-*C
56-Lead Shrunk Small Outline Package O56
51-85062-*C
2
Purchase of I C components from Cypress or one of its sublicensed Associated Companies conveys a license under the Philips
I2C Patent Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification
as defined by Philips. VIA is a trademark of VIA Technologies, Inc. Pentium 4 is a registered trademark of Intel Corporation.
Athlon is a trademark of AMD Corporation, Inc. Dial-a-Frequency is a registered trademark, and Dial-a-Skew, Dial-a-dB, and
Dial-a-Ratio are trademarks, of Cypress Semiconductor. All product and company names mentioned in this document are the
trademarks of their respective holders.
Document #: 38-07471 Rev. *D
Page 18 of 19
© Cypress Semiconductor Corporation, 2005. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be
used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its
products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
CY28341-2
Document History Page
Document Title: CY28341-2 Universal Clock Chip for VIA™P4M/KT/KM400 DDR Systems
Document Number: 38-07471
REV.
ECN NO.
Issue Date
Orig. of
Change
Description of Change
**
118589
09/18/02
RGL
New Data Sheet
*A
122938
12/19/02
RBI
Add power up requirements to maximum ratings information
*B
124914
04/23/03
RGL
Fixed pin 1 and pin 2 in Pin Description table
Added KT400 feature to Features section
Corrected Figure 8 (K7 Load Termination) diagram
Simplified title
*C
127161
06/10/03
RGL
Fixed Spread Spectrum table
*D
333216
See ECN
RGL
Added Lead-free for SSOP device
Document #: 38-07471 Rev. *D
Page 19 of 19