Revised June 2005 74LVX161284 Low Voltage IEEE 161284 Translating Transceiver General Description Features The LVX161284 contains eight bidirectional data buffers and eleven control/status buffers to implement a full IEEE 1284 compliant interface. The device supports the IEEE 1284 standard and is intended to be used in an Extended Capabilities Port mode (ECP). The pinout allows for easy connection from the Peripheral (A-side) to the Host (cable side). ■ Supports IEEE 1284 Level 1 and Level 2 signaling standards for bidirectional parallel communications between personal computers and printing peripherals Outputs on the cable side can be configured to be either open drain or high drive (r 14 mA) and are connected to a separate power supply pin (VCC-cable) to allow these outputs to be driven by a higher supply voltage than the Aside. The pull-up and pull-down series termination resistance of these outputs on the cable side is optimized to drive an external cable. In addition, all inputs (except HLH) and outputs on the cable side contain internal pull-up resistors connected to the VCC-cable supply to provide proper termination and pull-ups for open drain mode. Outputs on the Peripheral side are standard low-drive CMOS outputs designed to interface with 3V logic. The DIR input controls data flow on the A1–A8/B1–B8 transceiver pins. ■ Translation capability allows outputs on the cable side to interface with 5V signals ■ All inputs have hysteresis to provide noise margin ■ B and Y output resistance optimized to drive external cable ■ B and Y outputs in high impedance mode during power down ■ Inputs and outputs on cable side have internal pull-up resistors ■ Flow-through pin configuration allows easy interface between the “Peripheral and Host” ■ Replaces the function of two (2) 74ACT1284 devices Ordering Code Order Number Package Number 74LVX161284MEA MS48A 48-Lead Small Shrink Outline Package (SSOP), JEDEC MO-118, 0.300" Wide Package Description 74LVX161284MTD MTD48 48-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 6.1mm Wide Device also available in Tape and Reel. Specify by appending suffix letter “X” to the ordering code. Connection Diagram Pin Descriptions Pin Names HD © 2005 Fairchild Semiconductor Corporation DS500202 Description High Drive Enable Input (Active HIGH) DIR Direction Control Input A1–A8 Inputs or Outputs B1–B8 Inputs or Outputs A9–A13 Inputs Y9–Y13 Outputs A14–A17 Outputs C14–C17 Inputs PLHIN Peripheral Logic HIGH Input PLH Peripheral Logic HIGH Output HLHIN Host Logic HIGH Input HLH Host Logic HIGH Output www.fairchildsemi.com 74LVX161284 Low Voltage IEEE 161284 Translating Transceiver January 1999 74LVX161284 Logic Symbol Truth Table Inputs Outputs DIR HD L L B1–B8 Data to A1–A8, and A9–A13 Data to Y9–Y13 (Note 1) C14–C17 Data to A14–A17 PLH Open Drain Mode L H B1–B8 Data to A1–A8, and A9–A13 Data to Y9–Y13 C14–C17 Data to A14–A17 H L A1–A8 Data to B1–B8 (Note 2) A9–A13 Data to Y9–Y13 (Note 1) C14–C17 Data to A14–A17 PLH Open Drain Mode H H A1–A8 Data to B1–B8 A9–A13 Data to Y9–Y13 C14–C17 Data to A14–A17 Note 1: Y9–Y13 Open Drain Outputs Note 2: B1–B8 Open Drain Outputs Logic Diagram www.fairchildsemi.com 2 Recommended Operating Conditions Supply Voltage 0.5V to 4.6V 0.5V to 7.0V VCC VCC—Cable Supply Voltage VCC—Cable Must Be t VCC Input Voltage (VI)—(Note 4) 0.5V to VCC 0.5V 0.5V to 5.5V (DC) 2.0V to 7.0V* A1–A13, PLHIN , DIR, HD B1–B8, C14–C17, HLHIN B1–B8, C14–C17, HLHIN VCC 3.0V to 3.6V VCC—Cable 3.0V to 5.5V DC Input Voltage (VI) 0V to VCC Open Drain Voltage (VO) 0V to 5.5V 40qC to 85qC Operating Temperature (TA) *40 ns Transient Output Voltage (VO) 0.5V to VCC 0.5V 0.5V to 5.5V (DC) 2.0V to 7.0V* A1–A8, A14–A17, HLH B1–B8, Y9–Y13, PLH B1–B8, Y9–Y13, PLH *40 ns Transient DC Output Current (IO) r25 mA r50 mA A1–A8, HLH B1–B8, Y9–Y13 PLH (Output LOW) 84 mA PLH (Output HIGH) 50 mA Input Diode Current (IIK)—(Note 4) DIR, HD, A9–A13, PLH, HLH, C14–C17 20 mA Output Diode Current (IOK) r50 mA 50 mA A1–A8, A14–A17, HLH B1–B8, Y9–Y13, PLH DC Continuous VCC or Ground Current Storage Temperature Note 3: Absolute maximum ratings are values beyond which the device may be damaged or have its useful life impaired. Fairchild does not recommend operation outside the databook specifications. r200 mA 65qC to 150qC ESD (HBM) Last Passing Voltage Note 4: Either voltage limit or current limit is sufficient to protect inputs. 2000V DC Electrical Characteristics Symbol Parameter VCC (V) VCC—Cable (V) TA 0qC to 70qC TA 40qC to 85qC Units Conditions Guaranteed Limits VIK Input Clamp 3.0 3.0 1.2 1.2 V Ii 18 mA Diode Voltage VIH VIL 'VT VOH Minimum An, Bn, PLHIN, DIR, HD 3.0–3.6 3.0–5.5 2.0 2.0 HIGH Level Cn 3.0–3.6 3.0–5.5 2.3 2.3 Input Voltage HLHIN 3.0–3.6 3.0–5.5 2.6 2.6 Maximum An, Bn, PLHIN, DIR, HD 3.0–3.6 3.0–5.5 0.8 0.8 LOW Level Cn 3.0–3.6 3.0–5.5 0.8 0.8 Input Voltage HLHIN 3.0–3.6 3.0–5.5 1.6 1.6 V V VT–VT Minimum Input An, Bn, PLHIN, DIR, HD 3.3 5.0 0.4 0.4 Hysteresis Cn 3.3 5.0 0.8 0.8 HLHIN 3.3 5.0 0.2 0.2 An, HLH 3.0 3.0 2.8 2.8 IOH 50 PA 3.0 3.0 2.4 2.4 IOH 4 mA Bn, Yn 3.0 3.0 2.0 2.0 IOH 14 mA Bn, Yn 3.0 4.5 2.23 2.23 IOH 14 mA PLH 3.15 3.15 3.1 3.1 IOH 500 PA Minimum HIGH Level Output Voltage 3 V VT–VT VT–VT V www.fairchildsemi.com 74LVX161284 Absolute Maximum Ratings(Note 3) 74LVX161284 DC Electrical Characteristics Symbol Parameter (Continued) VCC (V) VCC—Cable (V) TA 0 qC to 70qC TA 40qC to 85qC Units Conditions Guaranteed Limits VOL Maximum LOW 3.0 3.0 0.2 0.2 IOL 50 PA 3.0 3.0 0.4 0.4 IOL 4 mA Bn, Yn 3.0 3.0 0.8 0.8 IOL 14 mA Bn, Yn 3.0 4.5 0.77 0.77 IOL 14 mA PLH 3.0 3.0 0.85 0.95 IOL 84 mA PLH 3.0 4.5 0.8 0.9 IOL 84 mA B1–B8, Y9–Y13 3.3 3.3 60 60 3.3 5.0 55 55 An, HLH Level Output Voltage RD Maximum Output Impedance Minimum Output B1–B8, Y9–Y13 Impedance RP IIH IOZL IOFF IOFF 35 B1–B8, Y9–Y13, 3.3 3.3 1650 1650 3.3 5.0 1650 1650 Minimum Pull-Up B1–B8, Y9–Y13 3.3 3.3 1150 1150 Resistance C14–C17 3.3 5.0 1150 1150 Maximum Input A9–A13, PLHIN, 3.6 3.6 1.0 1.0 Current in HD, DIR, HLHIN C14–C17 3.6 3.6 50.0 50.0 C14–C17 3.6 5.5 100 100 Maximum Input A9–A13, PLHIN, 3.6 3.6 1.0 1.0 Current in HD, DIR, HLHIN (Note 5)(Note 7) : (Note 5)(Note 7) : : PA VI 3.6V VI 3.6V VI 5.5V PA VI 0.0V C14–C17 3.6 3.6 3.5 3.5 mA VI 0.0V C14–C17 3.6 5.5 5.0 5.0 mA VI 0.0V Maximum Output A1–A8 3.6 3.6 20 20 PA VO 3.6V Disable Current B1–B8 3.6 3.6 50 50 PA VO 3.6V (HIGH) B1–B8 3.6 5.5 100 100 PA VO 5.5V Maximum A1–A8 3.6 3.6 20 20 PA VO 0.0V Output Disable B1–B8 3.6 3.6 3.5 3.5 mA Current (LOW) B1–B8 3.6 5.5 5.0 5.0 mA Power Down B1–B8, Y9–Y13, Output Leakage PLH 0.0 0.0 100 100 PA VO 5.5V 0.0 0.0 100 100 PA VI 0.0 0.0 250 250 PA (Note 6) 0.0 0.0 250 250 PA (Note 6) Power Down C14–C17, HLHIN Power Down Leakage to VCC IOFF—ICC2 Power Down Leakage to VCC—Cable ICC 30 35 C14–C17 Input Leakage IOFF—ICC 30 5.0 Maximum Pull-Up LOW State IOZH 3.3 Resistance HIGH State IIL 3.3 3.3 V 5.5V Maximum Supply 3.6 3.6 45 45 mA VI VCC or GND Current 3.6 5.5 70 70 mA VI VCC or GND Note 5: Output impedance is measured with the output active LOW and active HIGH (HD HIGH). Note 6: Power-down leakage to V CC or VCC—Cable is tested by simultaneously forcing all pins on the cable-side (B1–B8, Y9–Y13, PLH, C14–C17 and HLHIN) to 5.5V and measuring the resulting ICC or ICC—Cable. Note 7: This parameter is guaranteed but not tested, characterized only. www.fairchildsemi.com 4 TA Symbol VCC Parameter 0qC to 70qC TA 3.0V–3.6V VCC—Cable 40qC to 85qC VCC 3.0V–5.5V 3.0V–3.6V VCC—Cable Units Figure Number 3.0V–5.5V Min Max Min Max tPHL A1–A8 to B1–B8 2.0 40.0 2.0 44.0 ns Figure 1 tPLH A1–A8 to B1–B8 2.0 40.0 2.0 44.0 ns Figure 2 tPHL B1–B8 to A1–A8 2.0 40.0 2.0 44.0 ns Figure 3 tPLH B1–B8 to A1–A8 2.0 40.0 2.0 44.0 ns Figure 3 tPHL A9–A13 to Y9–Y13 2.0 40.0 2.0 44.0 ns Figure 1 tPLH A9–A13 to Y9–Y13 2.0 40.0 2.0 44.0 ns Figure 2 tPHL C14–C17 to A14–A17 2.0 40.0 2.0 44.0 ns Figure 3 tPLH C14–C17 to A14–A17 2.0 40.0 2.0 44.0 ns Figure 3 tSKEW LH-LH or HL-HL 12.0 ns (Note 9) tPHL PLHIN to PLH 44.0 ns Figure 1 tPLH PLHIN to PLH 2.0 40.0 2.0 44.0 ns Figure 2 tPHL HLHIN to HLH 2.0 40.0 2.0 44.0 ns Figure 3 tPLH HLHIN to HLH 2.0 40.0 2.0 44.0 ns Figure 3 tPHZ Output Disable Time 2.0 15.0 2.0 18.0 tPLZ DIR to A1–A8 2.0 15.0 2.0 18.0 ns Figure 7 tPZH Output Enable Time 2.0 50.0 2.0 50.0 tPZL DIR to A1–A8 2.0 50.0 2.0 50.0 ns Figure 8 tPHZ Output Disable Time 2.0 50.0 2.0 50.0 tPLZ DIR to B1–B8 2.0 50.0 2.0 50.0 ns Figure 9 tpEN Output Enable Time 2.0 25.0 2.0 28.0 HD to B1–B8, Y9–Y13 2.0 25.0 2.0 28.0 ns Figure 2 Output Disable Time 2.0 25.0 2.0 28.0 HD to B1–B8, Y9–Y13 2.0 25.0 2.0 ns Figure 2 tpDIS tpEN–tpDIS 10.0 2.0 40.0 Output Enable- 2.0 10.0 28.0 12.0 ns V/ns Output Disable tSLEW Output Slew Rate tPLH B1–B8, Y9–Y13 tPHL tr, tf 0.05 0.40 0.05 0.40 0.05 0.40 0.05 0.40 Figure 4 Figure 6 tRISE and tFALL 120 120 B1–B8 (Note 8), 120 120 ns Figure 5 (Note 10) Y9–Y13 (Note 8) Note 8: Open Drain Note 9: tSKEW is measured for common edge output transitions and compares the measured propagation delay for a given path type: (i) A1–A8 to B1–B8, A9–A13 to Y9–Y13 (ii) B1–B8 to A1–A8 (iii) C14–C17 to A14–A17 Note 10: This parameter is guaranteed but not tested, characterized only. Capacitance Symbol Parameter CIN Input Capacitance CI/O (Note 11) I/O Pin Capacitance Note 11: CI/O is measured at frequency Typ Units 3 pF VCC 0.0V (HD, DIR, A9–A13, C14–C17, PLHIN and HLHIN) Conditions 5 pF VCC 3.3V 1 MHz, per MIL-STD-883B, Method 3012 5 www.fairchildsemi.com 74LVX161284 AC Electrical Characteristics 74LVX161284 AC Loading and Waveforms Pulse Generator for all pulses: Rate d1.0 MHz; ZO d 50:; tf d 2.5 ns, tr d 2.5 ns. FIGURE 1. Port A to B and A to Y Propagation Delay Waveforms FIGURE 2. Port A to B and A to Y Output Waveforms FIGURE 3. Port B to A, C to A and HLHin to HLH Propagation Delay Waveforms www.fairchildsemi.com 6 74LVX161284 AC Loading and Waveforms (Continued) FIGURE 4. Port A to B and A to Y HL Slew Test Load and Waveforms FIGURE 5. Port A to B and A to Y LH Slew Test Load and Waveforms 7 www.fairchildsemi.com 74LVX161284 AC Loading and Waveforms tr Output Rise Time, Open Drain tf Output Fall Time, Open Drain (Continued) FIGURE 6. Ports A to B and A to Y Rise and Fall Test Load and Waveforms for Open Drain Outputs FIGURE 7. tPHZ and tPLZ Test Load and Waveforms, DIR to A1–A8 www.fairchildsemi.com 8 74LVX161284 AC Loading and Waveforms (Continued) FIGURE 8. tPZH and tPZL Test Load and Waveforms, DIR to A1–A8 FIGURE 9. tPHZ and tPLZ Test Load and Waveforms DIR to B1–B8 9 www.fairchildsemi.com 74LVX161284 Physical Dimensions inches (millimeters) unless otherwise noted 48-Lead Small Shrink Outline Package (SSOP), JEDEC MO-118, 0.300" Wide Package Number MS48A www.fairchildsemi.com 10 74LVX161284 Low Voltage IEEE 161284 Translating Transceiver Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 48-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 6.1mm Wide Package Number MTD48 Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. www.fairchildsemi.com 11 www.fairchildsemi.com