LINER LTC1760CFW

LTC1760
Dual Smart Battery
System Manager
DESCRIPTIO
U
FEATURES
■
■
■
■
■
■
■
■
■
■
■
■
■
■
SMBus Charger/Selector for Two Smart Batteries*
Voltage and Current Accuracy within 0.2% of Value
Reported by Battery
Simplifies Construction of “Smart Battery System
Manager”
Includes All SMBus Charger V1.1 Safety Features
Supports Autonomous Operation without a Host
Allows Both Batteries to Discharge Simultaneously
into Single Load with Low Loss (Ideal Diode)
SMBus Switching for Dual Batteries with Alarm
Monitoring for Charging Battery at All Times
Pin Programmable Limits for Maximum Charge
Current and Voltage Improve Safety
Fast Autonomous Power Path Switching (<10µs)
Low Loss Simultaneous Charging of Two Batteries
>95% Efficient Synchronous Buck Charger
AC Adapter Current Limiting* Maximizes Charge Rate
SMBus Accelerator Improves SMBus Timing**
Available in 48-Lead TSSOP Package
U
APPLICATIO S
■
■
Portable Computers and Instruments
Standalone Dual Smart Battery Chargers
Battery Backup Systems
A proprietary PowerPathTM architecture supports simultaneous charging or discharging of both batteries. Typical
battery run times are extended by up to 10%, while
charging times are reduced by up to 50%. The LTC1760
automatically switches between power sources in less
than 10µs to prevent power interruption upon battery or
wall adapter removal.
The LTC1760 implements all elements of a version 1.1
“Smart Battery System Manager” except for the generation of composite battery information. An internal multiplexer cleanly switches the SMBus Host to either of the
two attached Smart Batteries without generating partial
messages to batteries or SMBus Host. Thermistors on
both batteries are automatically monitored for temperature and disconnection information (SafetySignal).
, LTC and LT are registered trademarks of Linear Technology Corporation.
PowerPath is a trademark of Linear Technology Corporation.
Protected by U.S. Patents, including *5723970 **6650174
U
■
The LTC®1760 Smart Battery System Manager is a highly
integrated level 3 battery charger and selector intended for
products using dual smart batteries. Three SMBus interfaces allow the LTC1760 to servo to the internal voltage
and currents measured by the batteries while allowing an
SMBus Host to monitor either battery’s status. Charging
accuracy is determined by the battery’s internal voltage
and current measurement, typically better than ±0.2%.
TYPICAL APPLICATIO
Dual Battery Charger/Selector System Architecture
Dual vs Sequential Charging
SYSTEM
POWER
LTC1760
SMBus (HOST)
SafetySignal 1
SMBus 1
3500
3000
2500
2000
1500
1000
500
0
3500
3000
2500
2000
1500
1000
500
0
BAT1
CURRENT
1760 TA01
BAT2
CURRENT
SEQUENTIAL
BAT1
CURRENT
BAT2
CURRENT
DUAL
100
MINUTES
0
SafetySignal 2
SMBus 2
BATTERY CURRENT (mA)
DC
IN
50
100
150
200
TIME (MINUTES)
250
300
BATTERY TYPE: 10.8V Li-Ion (MOLTECH NI2020)
REQUESTED CURRENT = 3A
REQUESTED VOLTAGE = 12.3V
MAX CHARGER CURRENT = 4.1A
1760 TA03
1760f
1
LTC1760
U
W W
W
ABSOLUTE
AXI U RATI GS
U
W
U
PACKAGE/ORDER I FOR ATIO
(Note 1)
Voltage from DCIN, SCP, SCN, CLP,
VPLUS, SW to GND ................................... 32V/–0.3 V
Voltage from SCH1, SCH2 to GND ................ 28V/–0.3 V
Voltage from BOOST to GND ........................ 37V/ –0.3V
CSP, CSN, BAT1, BAT2 to GND ..................... 28V/–0.3V
LOPWR, DCDIV to GND ................................ 10V/ –0.3V
Voltage from VCC2, VDDS to GND .................... 7V/–0.3 V
SDA1, SDA2, SDA, SCL1, SCL2, SCL, SMBALERT
to GND ........................................................ 7V/–0.3V
MODE to GND ..................................... VCC2 +0.3V/–0.3V
COMP1 to GND ............................................... 5V/ –0.3V
Maximum DC Current Into Pin
SDA1, SDA2, SDA, SCL1, SCL2, SCL .............. ±3mA
TH1A, TH2A ..................................................... –5mA
TH1B, TH2B .................................................. –102µA
Operating Ambient Temperature (Note 6) .... 0°C to 70°C
Operating Junction Temperature ...........–40°C to 125°C
Storage Temperature .............................–65°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
TOP VIEW
VPLUS
BAT2
BAT1
SCN
SCP
GDCO
GDCI
GB1O
GB1I
GB2O
GB2I
LOPWR
VSET
ITH
ISET
DCDIV
SCL2
SCL
SCL1
VDDS
SDA2
SDA
SDA1
GND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
SCH2
GCH2
GCH1
SCH1
TGATE
BOOST
SW
DCIN
VCC
BGATE
PGND
COMP1
CLP
CSP
CSN
VLIMIT
ILIMIT
TH1B
TH1A
SMBALERT
TH2A
TH2B
MODE
VCC2
ORDER PART
NUMBER
LTC1760CFW
FW PACKAGE
48-LEAD PLASTIC TSSOP
TJMAX = 125°C, θJA = 110°C/W
Consult LTC Marketing for parts specified with wider operating temperature ranges.
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VDCIN = 20V, VBAT1 = 12V, VBAT2 = 12V, VVDDS = 3.3V, VVCC2 = 5.2V
unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
DCIN Operating Range
DCIN Selected
6
ICH0
ICH1
DCIN Operating Current
Not Charging (DCIN Selected) (Note 10)
Charging (DCIN Selected) (Note 10)
IVCC2_AC1
IVCC2_AC0
VCC2 Operating Current
AC Present (Note 11)
AC Not Present (Note 11)
TYP
MAX
UNITS
Supply and Reference
Battery Operating Voltage Range Battery Selected, PowerPath Function
Battery Selected, Charging Function (Note 2)
28
V
1
1.3
1.5
2
mA
mA
0.75
75
1
100
mA
µA
28
28
V
V
6
0
IBAT
Battery Drain Current
Battery Selected, Not Charging, VDCIN = 0V (Note 10)
175
µA
VFDC
VFB1
VFB2
VFSCN
VPLUS Diodes Forward Voltage:
DCIN to VPLUS
BAT1 to VPLUS
BAT2 to VPLUS
SCN to VPLUS
IVCC = 10mA
IVCC = 0mA
IVCC = 0mA
IVCC = 0mA
0.8
0.7
0.7
0.7
V
V
V
V
UVLO
Undervoltage Lockout Threshold VPLUS Ramping Down, Measured at VPLUS to GND
●
3
VVCC
VCC Regulator Output Voltage
●
4.9
VLDR
VCC Load Regulation
IVCC = 0mA to 10mA
●
With Respect to Voltage Reported by Battery
VCHMIN < Requested Voltage < VLIMIT
●
5
V
5.2
5.5
V
0.2
1
%
32
mV
Switching Regulator
VTOL
Voltage Accuracy
–32
1760f
2
LTC1760
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VDCIN = 20V, VBAT1 = 12V, VBAT2 = 12V, VVDDS = 3.3V, VVCC2 = 5.2V
unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
ITOL
Current Accuracy
With Respect to Current Reported by Battery
4mV/RSENSE < Requested Current < ILIMIT (Min)
(Note 12)
RILIMIT = 0 (Short to GND)
RILIMIT = 10k ±1%
RILIMIT = 33k ±1%
RILIMIT = Open (or Short ILIMIT to VCC2)
f0SC
Regulator Switching Frequency
fDO
Regulator Switching Frequency in Low
Dropout Mode
DCMAX
Regulator Maximum Duty Cycle
IMAX
MIN
●
●
●
●
TYP
–2
–4
–8
–8
MAX
2
4
8
8
255
300
Duty Cycle ≥99%
20
25
99
99.5
Maximum Current Sense Threshold
VITH = 2.2V
140
155
ISNS
CA1 Input Bias Current
VCSP = VCSN > 5V
CMSL
CA1/I1 Input Common Mode Low
CMSH
CA1/I1 Input Common Mode High
VCL1
CL1 Turn-On Threshold
TG tr
TG tf
TGATE Transition Time:
TGATE Rise Time
TGATE Fall Time
BG tr
BG tf
345
mA
mA
mA
mA
kHz
kHz
%
190
150
mV
µA
0
V
VDCIN – 0.2
V
100
100
105
108
mV
mV
CLOAD = 3300pF, 10% to 90%
CLOAD = 3300pF, 10% to 90%
50
50
90
90
ns
ns
BGATE Transition Time:
BGATE Rise Time
BGATE Fall Time
CLOAD = 3300pF, 10% to 90%
CLOAD = 3300pF, 10% to 90%
50
40
90
80
ns
ns
VTR
DCDIV/LOPWR Threshold
VDCDIV or VLOPWR Falling
1.19
1.215
V
VTHYS
DCDIV/LOPWR Hysteresis Voltage
VDCDIV or VLOPWR Rising
30
IBVT
DCDIV/LOPWR Input Bias Current
VDCDIV or VLOPWR = 1.19V
20
200
nA
VTSC
Short-Circuit Comparator Threshold
VSCP – VSCN, VCC ≥ 5V
100
115
mV
VFTO
Fast Power Path Turn-Off Threshold
VDCDIV Rising from VCC
7
7.9
VOVSD
Overvoltage Shutdown Threshold as a
Percent of Programmed Charger Voltage
VSET Rising from 0.8V until TGATE and BGATE
Stop Switching
IRES
IDAC Resolution
Guaranteed Monotonic
tIP
tILOW
IDAC Pulse Period:
Normal Mode
Wake-Up Mode
●
95
94
UNITS
Trip Points
●
●
1.166
90
6
mV
107
V
%
DACs
Charging Current Granularity
10
6
RILIMIT = (Short ILIMIT to GND)
RILIMIT = 10k ±1%
RILIMIT = 33k ±1%
RILIMIT = Open (or Short ILIMIT to VCC2 )
IWAKE_UP
Wake-Up Charging Current (Note 5)
ILIMIT
Charging Current Limit
RILIMIT = 0 (Short ILIMIT to GND)
RILIMIT = 10k ±1%
RILIMIT = 33k ±1%
RILIMIT = Open (or Short ILIMIT to VCC2 )
VRES
VDAC Resolution
Guaranteed Monotonic (5V < VBAT < 25V)
Bits
10
50
15
1
2
4
4
●
●
●
●
µs
ms
mA
mA
mA
mA
60
80
100
mA
980
1960
2490
3920
1000
2000
3000
4000
1070
2140
3210
4280
mA
mA
mA
mA
11
Bits
1760f
3
LTC1760
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VDCIN = 20V, VBAT1 = 12V, VBAT2 = 12V, VVDDS = 3.3V, VVCC2 = 5.2V
unless otherwise noted.
SYMBOL
PARAMETER
VSTEP
VDAC Granularity
VLIMIT
Charging Voltage Limit
(Note 7)
CONDITIONS
MIN
TYP
MAX
16
RVLIMIT = 0 (Short VLIMIT to GND)
RVLIMIT = 10k ±1%
RVLIMIT = 33k ±1%
RVLIMIT = 100k ±1%
RVLIMIT = Open (or Short VLIMIT to VCC2 )(Note 13)
●
●
●
●
●
8400
12608
16832
21024
UNITS
mV
8432
12640
16864
21056
32768
8464
12672
16896
21088
mV
mV
mV
mV
mV
10
ms
Charge Mux Switches
tONC
GCH1/GCH2 Turn-On Time
VGCHX – VSCHX > 3V, CLOAD = 3000pF
5
tOFFC
GCH1/GCH2 Turn-Off Time
VGCHX – VSCHX < 1V, from Time of
VCSN < VBATX – 30mV, CLOAD = 3000pF
15
VCON
CH Gate Clamp Voltage
GCH1
GCH2
ILOAD = 1µA
VGCH1 – VSCH1
VGCH2 – VSCH2
5
5
5.8
5.8
7
7
V
V
CH Gate Off Voltage
GCH1
GCH2
ILOAD =10µA
VGCH1 – VSCH1
VGCH2 – VSCH2
–0.8
–0.8
–0.4
–0.4
0
0
V
V
VTOC
CH Switch Reverse Turn-Off Voltage
VBATX – VCSN, 5V ≤ VBATX ≤ 28V
●
5
20
40
mV
VFC
CH Switch Forward Regulation Voltage
VCSN – VBATX, 5V ≤ VBATX ≤ 28V
●
15
35
60
mV
GCH1/GCH2 Active Regulation:
Max Source Current
Max Sink Current
VGCHX – VSCHX = 1.5V
IOC(SRC)
IOC(SNK)
VCOFF
VCHMIN
µs
–2
2
BATX Voltage Below Which
Charging is Inhibited (Does Not Apply
to Wake-Up Mode)
3.5
µA
µA
4.7
V
PowerPath Switches
tDLY
Blanking Period after UVLO Trip
Switches Held Off
tPPB
Blanking Period after LOPWR Trip
Switches in 3-Diode Mode
tONPO
GB1O/GB2O/GDCO Turn-On Time
VGS < –3V, from Time of Battery/DC
Removal, or LOPWR Indication, CLOAD = 3000pF
●
5
10
µs
tOFFPO
GB1O/GB2O/GDCO Turn-Off Time
VGS > –1V, from Time of Battery/DC
Removal, or LOPWR Indication, CLOAD = 3000pF
●
3
7
µs
VPONO
Output Gate Clamp Voltage
GB1O
GB2O
GDCO
ILOAD = 1µA
Highest (VBAT1 or VSCP) – VGB1O
Highest (VBAT2 or VSCP) – VGB2O
Highest (VDCIN or VSCP) – VGDCO
6.25
6.25
6.25
7
7
7
V
V
V
Output Gate Off Voltage
GB1O
GB2O
GDCO
ILOAD = –25µA
Highest (VBAT1 or VSCP) – VGB1O
Highest (VBAT2 or VSCP) – VGB2O
Highest (VDCIN or VSCP) – VGDCO
0.18
0.18
0.18
0.25
0.25
0.25
V
V
V
VTOP
PowerPath Switch Reverse
Turn-Off Voltage
VSCP – VBATX or VSCP – VDCIN
6V ≤ VSCP ≤ 28V
●
5
20
60
mV
VFP
PowerPath Switch Forward
Regulation Voltage
VBATX – VSCP or VDCIN – VSCP
6V ≤ VSCP ≤ 28V
●
0
25
50
mV
GDCI/GB1I/GB2I Active Regulation:
Source Current
Sink Current
(Note 3)
VPOFFO
IOP(SRC)
IOP(SNK)
4.75
4.75
4.75
250
ms
1
sec
–4
75
µA
µA
1760f
4
LTC1760
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VDCIN = 20V, VBAT1 = 12V, VBAT2 = 12V, VVDDS = 3.3V, VVCC2 = 5.2V
unless otherwise noted.
SYMBOL
tONPI
PARAMETER
Gate B1I/B2I/DCI Turn-On Time
CONDITIONS
VGS < –3V, CLOAD = 3000pF (Note 4)
tOFFPI
Gate B1I/B2I/DCI Turn-Off Time
VGS > –1V, CLOAD = 3000pF (Note 4)
VPONI
Input Gate Clamp Voltage
GB1I
GB2I
GDCI
ILOAD = 1µA
Highest (VBAT1 or VSCP) – VGB1I
Highest (VBAT2 or VSCP) – VGB2I
Highest (VDCIN or VSCP) – VGDCI
Input Gate Off Voltage
GB1I
GB2I
GDCI
ILOAD = –25µA
Highest (VBAT1 or VSCP) – VGB1I
Highest (VBAT2 or VSCP) – VGB2I
Highest (VDCIN or VSCP) – VGDCI
Thermistor Trip
(COLD-RANGE/OVER-RANGE)
CLOAD(MAX) = 300pF (Note 9)
R1A = R2A = 1130Ω ±1%
R1B = R2B = 54900Ω ±1%
●
Thermistor Trip
(IDEAL-RANGE/COLD-RANGE)
CLOAD(MAX) = 300pF (Note 9)
R1A = R2A = 1130Ω ±1%
R1B = R2B = 54900Ω ±1%
Thermistor Trip
(HOT-RANGE/IDEAL-RANGE)
Thermistor Trip
(UNDER-RANGE/HOT-RANGE)
VPOFFI
MIN
TYP
300
MAX
10
4.75
4.75
4.75
UNITS
µs
µs
6.7
6.7
6.7
7.5
7.5
7.5
V
V
V
0.18
0.18
0.18
0.25
0.25
0.25
V
V
V
95
100
105
kΩ
●
28.5
30
32.5
kΩ
CLOAD(MAX) = 300pF (Note 9)
R1A = R2A = 1130Ω ±1%
R1B = R2B = 54900Ω ±1%
●
2.85
3
3.15
kΩ
CLOAD(MAX) = 300pF (Note 9)
R1A = R2A = 1130Ω ±1%
R1B = R2B = 54900Ω ±1%
●
425
500
575
Ω
0.8
V
Thermistor
Logic Levels
IPULLUP
SCL/SCL1/SCL2/SDA/SDA1/
SDA2 Input Low Voltage (VIL)
●
SCL/SCL1/SCL2/SDA/SDA1/
SDA2 Input High Voltage (VIH)
●
2.1
V
SCL/SCL1/SCL2/SDA/SDA1/
SDA2 Input Leakage Current
VSDA, VSCL, VSDA1, VSCL1,
VSDA2, VSCL2 = 0.8V
●
–5
5
µA
SCL/SCL1/SCL2/SDA/SDA1/
SDA2 Input Leakage Current
VSDA, VSCL, VSDA1, VSCL1, VSDA2,
VSCL2 = 2.1V
●
–5
5
µA
SCL1/SDA1/SCL2/SDA2 Pull-Up
Current When Not Connected to
SMBus Host
VSCL1 = VSDA1 = VSCL2 = VSDA2 = 0.4V
VVCC2 = 4.85V and 5.55V (Current is Through
Internal Series Resistor and Schottky to VCC2)
350
µA
SCL1/SDA1/SCL2/SDA2
Series Impedance to Host SMBus
VSDA1, VSCL1, VSDA2, VSCL2 = 0.8V
●
300
Ω
SCL/SDA Output Low Voltage (VOL).
LTC1760 Driving the Pin
IPULLUP = 350µA
●
0.4
V
SCL1/SDA1/SCL2/SDA2 Pullup
Output Low Voltage (VOL).
LTC1760 Driving the Pin with Battery
SMBus not Connected to Host SMBus
IPULLUP Internal to LTC1760
●
0.4
V
SCL1/SDA1/SCL2/SDA2
Output Low Voltage (VOL).
LTC1760 Driving the Pin with Battery
SMBus Connected to Host SMBus
IPULLUP = 350µA on Host Side
●
0.4
V
165
220
1760f
5
LTC1760
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VDCIN = 20V, VBAT1 = 12V, VBAT2 = 12V, VVDDS = 3.3V, VVCC2 = 5.2V
unless otherwise noted.
SYMBOL
VIL_VDDS
VIH_VDDS
PARAMETER
CONDITIONS
SCL/SCL1/SCL2/SDA/SDA1/ SDA2/
SMBALERT Power Down Leakage
VVCC2 = 0V, VVDDS = 0V,
VSCL, VSCL1, VSCL2, VSDA,
VSDA1, VSDA2, VSMBALERT = 5.5V
●
SMBALERT Output Low Voltage (VOL)
IPULLUP = 500µA
●
SMBALERT Output Pull-Up Current
VSMBALERT = 0.4V
VDDS Input Low Voltage (VIL)
VDDS Input High Voltage (VIH)
VDDS Operating Voltage
VDDS Operating Current
MIN
MAX
2
3.5
●
●
●
TYP
10
2.6
3
uA
0.4
V
17.5
µA
1.5
V
V
V
µA
5.5
18
VSCL, VSDA = VVDDS , VVDDS = 5V
UNITS
VIL_MODE
MODE Input Low Voltage (VIL)
VVCC2 = 4.85V
●
VIH_MODE
MODE Input High Voltage (VIH)
VVCC2 = 4.85V
●
VVCC2 • 0.7
MODE Input Current (IIH)
MODE = VVCC2 • 0.7V, VVCC2 = 4.85V
●
–1
1
µA
MODE Input Current (IIL)
MODE = VVCC2 • 0.3V, VVCC2 = 4.85V
●
–1
1
µA
●
140
210
sec
VVCC2 • 0.3
V
V
Charger Timing
tTIMEOUT
Timeout for Wake-Up Charging and
Controlled Charging
tQUERY
Sampling Rate Used by the LTC1760 to
Update Charging Parameters
175
1
sec
SMBus Timing
SCL Serial-Clock High Period(tHIGH)
At IPULLUP = 350µA, CLOAD = 150pF (Note 8)
●
4
SCL Serial-Clock Low Period (tLOW)
At IPULLUP = 350µA, CLOAD = 150pF (Note 8)
●
4.7
SDA/SCL Rise Time (tr)
CLOAD = 150pF, RPU = 9.31k (Note 8)
●
SDA/SCL Fall Time (tf)
CLOAD = 150pF, RPU = 9.31k (Note 8)
●
µs
µs
1000
ns
300
ns
1.42
V
SMBus Accelerator Trip Voltage Range
●
0.8
Start-Condition Setup Time (tSU:STA)
●
4.7
µs
Start-Condition Hold Time (tHD:STA)
●
4
µs
SDA to SCL Rising-Edge
Setup Time (tSU:DAT)
●
250
ns
SDA to SCL Falling-Edge Hold Time,
Slave Clocking in Data (tHD:DAT)
●
300
ns
●
25
tTIMEOUT_SMB The LTC1760 will Release the SMBus
and Terminate the Current Master or
Slave Command if the Command is not
Completed Before this Time
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 2. Battery voltage must be adequate to drive gates of power path
P-channel FET switches. This does not affect charging voltage of the
battery, which can be zero volts during wake-up charging.
Note 3. DCIN, BAT1, BAT2 are held at 12V and GDCI, GB1I, GB2I are
forced to 10.5V. SCP is set at 12V to measure source current at GDCI,
GB1I and GB2I. SCP is set at 11.9V to measure sink current at GDCI, GB1I
and GB2I.
Note 4. Extrapolated from testing with CL = 50pF.
Note 5. Accuracy dependent upon external sense resistor and
compensation components.
35
ms
Note 6. The LTC1760C is guaranteed to meet specified performance from
0°C to 70°C and is designed, characterized and expected to meet specified
performance at –40°C and 85°C, but is not tested at these extended
temperature limits.
Note 7. Charger servos to the value reported by a Voltage() query. This is
the internal cell voltage measured by the battery electronics and may be
lower than the terminal voltage. See “Operation Section 3.6” for more
information.
Note 8. CLOAD is the combined capacitance on the host’s SMBus
connection and the selected battery’s SMBus connection.
Note 9. CLOAD_MAX is the maximum allowed combined capacitance on
THxA, THxB and the battery’s SafetySignalx connections.
1760f
6
LTC1760
ELECTRICAL CHARACTERISTICS
Note 10. Does not include current supplied by VCC to VCC2 (IVCC2_AC1 or
IVCC2_AC0)
Note 11. Measured with thermistors not present, RVILIM and RILIM
removed and SMBALERT = 1. See Applications Information section:
“Calculating IC Operating Current” for example on how to calculate total IC
operating current.
Note 12. Requested currents below 44mV/RSENSE may not servo correctly
due to charger offsets. The charging current for requested currents below
4mV/RSENSE will be between 4mV/RSENSE and (Requested Current – 8mA).
Refer to Applications Information: “Setting Charger Output Current Limit”
for values of RSENSE.
Note 13. This limit is greater than the absolute maximum for the charger.
Therefore, there is no effective limitation for the voltage when this option
is selected.
U W
TYPICAL PERFOR A CE CHARACTERISTICS
10
–5
–10
–15
–20
5
BATTERY CURRENT (mA)
Current()–ChargingCurrent() (mA)
0
–5
–10
–15
–20
–25
4700
7132
11996 14428
9564
ChargingVoltage() (mV)
0
16860
800
3000
2500
16.0
15.5
2000
15.0
1500
BAT1
CURRENT
14.5
BAT2
CURRENT
14.0
13.5
0
20
1000
DUAL
100
MINUTES
50
100
150
200
TIME (MINUTES)
10.0
BAT2
VOLTAGE
500
SEQUENTIAL
12.0
11.0
BAT1
VOLTAGE
9.0
0
20
40
12
250
300
60 80 100 120 140 160 180
TIME (MINUTES)
BATTERY TYPE: 10.8V Li-Ion (MOLTECH NI2020)
LOAD CURRENT = 3A
1760 G05
DUAL
BAT1
VOLTAGE
11
10
BAT2
VOLTAGE
15
14
SEQUENTIAL
BAT1
VOLTAGE
13
12
11
MINUTES
8.0
1760 G04
BAT2
VOLTAGE
13
9.0
8.0
14
DUAL
BAT2
VOLTAGE
10.0
0
40 60 80 100 120 140 160
TIME (MINUTES)
BAT1 INITIAL CAPACITY = 0%
BAT2 INITIAL CAPACITY = 90%
PROGRAMMED CHARGER CURRENT = 3A
PROGRAMMED CHARGER VOLTAGE = 16.8V
BAT1
VOLTAGE
11.0
BATTERY CURRENT (mA)
BAT1
VOLTAGE
BAT2
CURRENT
15
12.0
BATTERY VOLTAGE (V)
16.5
BAT1
CURRENT
Dual Battery Dischage Time vs
Sequential Battery Discharge
(NiMH)
3500
BAT2
VOLTAGE
SEQUENTIAL
BATTERY TYPE: 10.8V Li-Ion (MOLTECH NI2020)
REQUESTED CURRENT = 3A
REQUESTED VOLTAGE = 12.3V
MAX CHARGER CURRENT = 4.1A
1760 G03
Dual Battery Discharge Time vs
Sequential Battery Discharge
(Li-Ion)
Dual Charging Batteries with
Different Charge State
BAT2
CURRENT
BAT1
CURRENT
0
1760 G02
1760 G01
17.0
3500
3000
2500
2000
1500
1000
500
0
3500
3000
2500
2000
1500
1000
500
0
4000
1600
2400
3200
ChargingCurrent() (mA)
BATTERY VOLTAGE (V)
Voltage()–ChargingVoltage() (mV)
0
BATTERY VOLTAGE (V)
Dual Battery Charge Time vs
Sequential Battery Charging
Charging Current Accuracy
Charging Voltage Accuracy
16
MINUTES
11
10
0
20
40
60
80
100
TIME (MINUTES)
120
140
BATTERY TYPE: 12V NiMH (MOLTECH NJ1020)
1760 G06
LOAD: 33W
1760f
7
LTC1760
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Efficiency vs Charging Current
14
BAT1
OUTPUT
12
BAT1 VOLTAGE (V)
EFFICIENCY (%)
50
40
30
10
8
6
LOAD
CONNECTED
4
LOAD
DISCONNECTED
2
0
0
0.025
0.50
0.10
IOUT (A)
2.5 4.0
0
–4 –2
LOAD VOLTAGE (V)
14
12.0
11.9
VIN = 20V
VDAC = 12.288V
IDAC = 4000mA
TA = 25°C
11.6
0
2
4 6 8
TIME (ms)
0
10 12 14 16
1000
2000
3000
CHARGE CURRENT (mA)
4000
1760 G09
1760 G08
Power Path Switching 1 and 2
15
12.1
11.7
1760 G07
16
12.2
11.8
20
10
12.3
VIN = 20V
VDAC = 12.29V
IDAC = 3000mA
LOAD CURRENT = 1A
TA = 25°C
80
60
12.4
BAT1 VOLTAGE (V)
90
70
Load Regulation
Load Dump
100
SMBus Accelerator Operation
CLOAD = 20µF
ILOAD = 0.8A
TA = 25°C
5V
VCC = 5V
CLD = 200pF
TA = 25°C
13
12
LTC1760
11
10
RPULLUP = 15k
9
LOPWR
THRESHOLD
8
0V
7
6
–50 –40 –30 –20 –10 0 10 20 30 40 50
TIME (µs)
1960 G10
1µs/DIV
1760 G11
U
U
U
PI FU CTIO S
Input Power Related
SCN (Pin 4): PowerPath Current Sensing Negative Input.
This pin should be connected directly to the “bottom”
(output side) of the low valued resistor in series with the
three PowerPath switch pairs, for detecting short-circuit
current events. Also powers the LTC1760 internal circuitry
when all other sources are absent.
SCP (Pin 5): PowerPath Current Sensing Positive Input.
This pin should be connected directly to the “top” (switch
side) of the low valued resistor in series with the three
PowerPath switch pairs, for detecting short-circuit current events.
GDCO (Pin 6): DCIN Output Switch Gate Drive. Together
with GDCI, this pin drives the gate of the P-channel switch
in series with the DCIN input switch.
GDCI (Pin 7): DCIN Input Switch Gate Drive. Together with
GDCO, this pin drives the gate of the P-channel switch
connected to the DCIN input.
GB1O (Pin 8): BAT1 Output Switch Gate Drive. Together
with GB1I, this pin drives the gate of the P-channel switch
in series with the BAT1 input switch.
GB1I (Pin 9): BAT1 Input Switch Gate Drive. Together with
GB1O, this pin drives the gate of the P-channel switch
connected to the BAT1 input.
1760f
8
LTC1760
U
U
U
PI FU CTIO S
GB2O (Pin 10): BAT2 Output Switch Gate Drive. Together
with GB2I, this pin drives the gate of the P-channel switch
in series with the BAT2 input switch.
GB2I (Pin 11): BAT2 Input Switch Gate Drive. Together
with GB2O, this pin drives the gate of the P-channel switch
connected to the BAT2 input.
CLP (Pin 36): This is the Positive Input to the Supply
Current Limiting Amplifier CL1. The threshold is set at
100mV above the voltage at the DCIN pin. When used to
limit supply current, a filter is needed to filter out the
switching noise.
Battery Charging Related
VSET (Pin 13): The Tap Point of a Programmable Resistor
Divider which Provides Battery Voltage Feedback to the
Charger. A capacitor from CSN to VSET and one from VSET
to GND provide necessary compensation and filtering for
the voltage loop.
ITH (Pin 14): This is the Control Signal of the Inner Loop
of the Current Mode PWM. Higher ITH corresponds to
higher charging current in normal operation. A capacitor
of at least 0.1µF to GND filters out PWM ripple. Typical fullscale output current is 30µA. Nominal voltage range for
this pin is 0V to 2.4V.
ISET (Pin 15): A Capacitor from ISET to GND is Required to
Filter Higher Frequency Components from the Delta-Sigma
IDAC.
COMP1 (Pin 37): This is the Compensation Node for the
Amplifier CL1. A capacitor is required from this pin to
GND if input current amplifier CL1 is used. At input
adapter current limit, this node rises to 1V. By forcing
COMP1 to GND, amplifier CL1 will be defeated (no
adapter current limit). COMP1 can source 10µA.
BGATE (Pin 39): Drives the Gate of the Bottom External
MOSFET of the Battery Charger Buck Converter.
SW (Pin 42): Connected to Source of Top External MOSFET
Switch. Used as reference for top gate driver.
BOOST (Pin 43): Supply to Topside Floating Driver. The
bootstrap capacitor is returned to this pin. Voltage swing
at this pin is from a diode drop below VCC to (DCIN + VCC).
TGATE (Pin 44): Drives the Gate of the Top External
MOSFET of the Battery Charger Buck Converter.
SCH1 (Pin 45), SCH2 (Pin 48): Charger MUX Switch
Source Returns. These two pins are connected to the
sources of Q3/Q4 and Q9/Q10 (see Typical Applications).
A small pull-down current source returns these nodes to
0V when the switches are turned off.
GCH1 (Pin 46), GCH2 (Pin 47): Charger MUX Switch
Gate Drives. These two pins drive the gates of the backto-back N-channel switch pairs, Q3/Q4 and Q9/Q10,
between the charger output and the two batteries (see
Typical Applications).
External Power Supply Pins
ILIMIT (Pin 32): An external resistor (RILIMIT) is connected
between this pin and GND. The value of the external
resistor programs the range and resolution of the programmed charger current.
VPLUS (Pin 1): Supply. The VPLUS pin is connected via
four internal diodes to the DCIN, SCN, BAT1, and BAT2
pins. Bypass this pin with a 0.1µF capacitor and a 1µF
capacitor. See Typical Applications for complete circuit.
VLIMIT (Pin 33): An external resistor (RVLIMIT)is connected
between this pin and GND. The value of the external
resistor programs the range and resolution of the voltage
DAC.
BAT1 (Pin 3), BAT2 (Pin 2): These two pins are the inputs
from the two batteries for power to the LTC1760.
CSN (Pin 34): Current Amplifier CA1 Input. Connect this to
the common output of the charger MUX switches.
CSP (Pin 35): Current Amplifier CA1 Input. This pin and
the CSN pin measure the voltage across the sense resistor,
RSENSE, to provide the instantaneous current signals required for both peak and average current mode operation.
LOPWR (Pin 12): LOPWR Comparator Input from External Resistor Divider Connected from SCN to GND. If the
voltage at LOPWR pin is lower than the LOPWR comparator threshold, then system power has failed and
power is autonomously switched to a higher voltage
source, if available.
1760f
9
LTC1760
U
U
U
PI FU CTIO S
DCDIV (Pin 16): DCDIV Comparator Input from External
Resistor Divider Connected from DCIN to GND. If the
voltage at DCDIV pin is above the DCDIV comparator
threshold, then the AC_PRESENT bit is set and the wall
adapter power is considered to be adequate to charge the
batteries. If DCDIV is taken more than 1.8V above VCC,
then all of the power path switches are latched off until all
power is removed.
DCIN (Pin 41): Supply. External DC power source. A
0.1µF bypass capacitor must be connected to this pin as
close as possible. No series resistance is allowed, since
the adapter current limit comparator input is also this pin.
Internal Power Supply Pins
VDDS (Pin 20): Power Supply for SMBus Accelerators.
Also used in conjunction with MODE pin to modify the
LTC1760 operating mode.
GND (Pin 24): Ground for Low Power Circuitry.
VCC2 (Pin 25): The VCC2 Power Supply is used Primarily to
Power Internal Logic Circuitry. Must be connected to VCC.
PGND (Pin 38): High Current Ground Return for BGATE
Driver.
VCC (Pin 40): Internal Regulator Output. Bypass this
output with at least a 2µF to 4.7µF capacitor. Do not use
this regulator output to supply external circuitry except
as shown in the application circuit.
SBS Interface Pins
SCL2 (Pin 17): SMBus Clock Signal to Smart Battery 2. Do
not connect to an external pull-up. The LTC1760 connects
this pin to an internal pull-up (IPULLUP) when required.
SCL (Pin 18): SMBus Clock Signal to SMBus Host. Also
used to determine flashing rate for stand-alone charge
indicators. Requires an external pullup to VDDS (normal
SMBus operating mode). Connected to internal SMBus
accelerator.
SDA2 (Pin 21): SMBus Data Signal to Smart Battery 2. Do
not connect to an external pull-up. The LTC1760 connects
this pin to an internal pull-up (IPULLUP) when required.
SDA (Pin 22): SMBus Data Signal to SMBus Host. Also
used to indicate charging status of Battery 2. Requires an
external pullup to VDDS. Connected to internal SMBus
accelerator.
SDA1 (Pin 23): SMBus Data Signal to Smart Battery 1. Do
not connect to an external pull-up. The LTC1760 connects
this pin to an internal pull-up (IPULLUP) when required.
MODE (Pin 26): Used in conjunction with VDDS to allow
SCL, SDA and SMBALERT to indicate charging status.
May also be used as a hardware charge inhibit.
TH2B (Pin 27): Thermistor Force/Sense Connection to
Smart Battery 2 SafetySignal. Connect to Battery 2 thermistor through resistor network shown in “Typical
Application.”
TH2A (Pin 28): Thermistor Force/Sense Connection to
Smart Battery 2 SafetySignal. Connect to Battery 2 thermistor through resistor network shown in “Typical
Application.”
SMBALERT (Pin 29): Active Low Interrupt Pin. Signals
SMBus Host that there has been a change of status in
battery or AC presence. Open drain with weak current
source pull-up to VCC2 (with Schottky to allow it to be
pulled to 5V externally). Also used to indicate charging
status of Battery 1.
TH1A (Pin 30): Thermistor Force/Sense Connection to
Smart Battery 1 SafetySignal. Connect to Battery 1 thermistor through resistor network shown in “Typical
Application.”
TH1B (Pin 31): Thermistor Force/Sense Connection to
Smart Battery 1 SafetySignal. Connect to Battery 1 thermistor through resistor network shown in “Typical
Application.”
SCL1 (Pin 19): SMBus Clock Signal to Smart Battery 1. Do
not connect to an external pull-up. The LTC1760 connects
this pin to an internal pull-up (IPULLUP) when required.
1760f
10
LTC1760
W
BLOCK DIAGRA
GB1I GB1O
9
GB2I GB2O
8
11
GDCI GDCO
10
7
6
100mV
SWDC
DRIVER
5 SCP
100Ω
–
SWB2
DRIVER
+
SWB1
DRIVER
SHORT CIRCUIT
4 SCN
32 ILIMIT
LIMIT
DECODER
CHARGE
PUMP
DCIN
33 VLIMIT
VCC2
10µA
ON
+
–
GCH1 46
29 SMBALERT
SCH1 45
ON
GCH2 47
SEQUENCER
26 MODE
+
–
CSN
20 VDDS
SCH2 48
BAT1
3
BAT2
2
18 SCL
AC_PRESENT
22 SDA
SMBus
INTERFACE
19 SCL1
CHARGE
VPLUS
1
23 SDA1
SCN
17 SCL2
21 SDA2
VCC2 25
VCC 40
VCC
REGULATOR
30 TH1A
SAFETY
SIGNAL
DECODER
GND 24
DCDIV 16
31 TH1B
28 TH2A
27 TH2B
+
–
LOPWR 12
PowerPath
CONTROLLER
15 ISET
10-BIT ∆Σ
CURRENT DAC
+
–
1.19V
CSP-CSN
3kΩ
DCIN 41
0.86V
3k
+
3k
34 CSN
–
gm = 1.4m
–
TON
35 CSP
CA1
Ω
+
BGATE
–
LOW DROP
DETECT
0V
CSN
–
OSCILLATOR
CA2
BOOST 43
+
TGATE 44
ICMP
Q
R
–+
3mV
–
PWM
LOGIC
VCC
S
+
÷15
SW 42
0.8V
BUFFERED ITH
BGATE 39
Ω
40mV
400k
EA
13 VSET
+
–
gm = 1.4m
11-BIT ∆Σ
VOLTAGE DAC
Ω
CLP 36
+
CL1
gm = 0.4m
+
DCIN
100mV
–
IREV
PGND 38
0.8V
37
COMP1
14
ITH
1760 BD
1760f
11
LTC1760
U U
TABLE OF CO TE TS
(For Operation Section)
1
Overview .............................................................................................................................................................................................. 13
2
The SMBus Interface ........................................................................................................................................................................... 13
2.1
SMBus Interface Overview ............................................................................................................................................................... 13
2.2
Data Bit Definition of Supported SMBus Functions. ......................................................................................................................... 14
2.3
Description of Supported SMBus Functions .................................................................................................................................... 16
2.3.1
BatterySystemState() ('h01) ........................................................................................................................................................ 16
2.3.2
BatterySystemStateCont() ('h02) ................................................................................................................................................. 17
2.3.3
BatterySystemInfo() ('h04) .......................................................................................................................................................... 18
2.3.4
LTC() ('h3c) ................................................................................................................................................................................. 19
2.3.5
BatteryMode() ('h03) ................................................................................................................................................................... 19
2.3.6
Voltage() ('h09) ........................................................................................................................................................................... 19
2.3.7
Current() ('h0a) ............................................................................................................................................................................ 20
2.3.8
ChargingCurrent() ('h14) ............................................................................................................................................................. 20
2.3.9
ChargingVoltage() ('h15) ............................................................................................................................................................. 20
2.3.10
AlarmWarning() ('h16) ................................................................................................................................................................ 20
2.3.11
AlertResponse() ........................................................................................................................................................................... 21
2.4
SMBus Dual Port Operation ............................................................................................................................................................. 21
2.5
LTC1760 SMBus Controller Operation ............................................................................................................................................. 22
2.6
LTC1760 SMBALERT Operation ...................................................................................................................................................... 24
3
Charging Algorithm Overview .............................................................................................................................................................. 24
3.1
Wake-Up Charging Initiation ............................................................................................................................................................ 24
3.2
Wake-Up Charging Termination ....................................................................................................................................................... 24
3.3
Wake-Up Charging Current and Voltage Limits ............................................................................................................................... 25
3.4
Controlled Charging Initiation .......................................................................................................................................................... 25
3.5
Controlled Charging Termination ..................................................................................................................................................... 25
3.6
Controlled Charging Current and Voltage Programming .................................................................................................................. 26
4
System Power Management Algorithm and Battery Calibration .......................................................................................................... 27
4.1
Turning Off System Power ............................................................................................................................................................... 27
4.2
Power-By Algorithm When No Battery is Being Calibrated .............................................................................................................. 27
4.3
Power-By Algorithm When a Battery is Being Calibrated ................................................................................................................. 27
4.4
Power-By Reporting ........................................................................................................................................................................ 27
5
Battery Calibration (Conditioning) ....................................................................................................................................................... 28
5.1
Selecting a Battery to be Calibrated ................................................................................................................................................. 28
5.2
Initiating Calibration of Selected Battery .......................................................................................................................................... 28
5.3
Terminating Calibration of Selected Battery ..................................................................................................................................... 28
6
MODE Pin Operation ............................................................................................................................................................................ 29
6.1
Stand Alone Charge Indication ......................................................................................................................................................... 29
6.2
Hardware Charge Inhibit .................................................................................................................................................................. 29
6.3
Charging When SCL and SDA are Low ............................................................................................................................................ 29
6.4
Charging With an SMBus Host ........................................................................................................................................................ 29
7
Battery Charger Controller ................................................................................................................................................................... 29
7.1
Charge MUX Switches ..................................................................................................................................................................... 30
7.2
Dual Charging .................................................................................................................................................................................. 30
8
PowerPath Controller .......................................................................................................................................................................... 31
8.1
Autonomous PowerPath Switching ................................................................................................................................................. 31
8.2
Short-Circuit Protection ................................................................................................................................................................... 31
8.3
Emergency Turn-Off ........................................................................................................................................................................ 32
8.4
Power-Up Strategy .......................................................................................................................................................................... 32
9
The Voltage DAC Block ........................................................................................................................................................................ 32
10 The Current DAC Block ........................................................................................................................................................................ 32
1760f
12
LTC1760
U
OPERATIO
(Refer to Block Diagram and Typical Application Figure)
1 Overview
The LTC1760 is composed of an SMBus interface with
dual port capability, a sequencer for managing system
power and the charging and discharging of two batteries,
a battery charger controller, charge mux controller, powerpath controller, a 10-bit current DAC (IDAC) and 11-bit
voltage DAC (VDAC). When coupled with optional system
software for generating composite battery information, it
forms a complete Smart Battery System Manager for
charging and selecting two smart batteries. The battery
charger is controlled by the sequencer which uses the
level 3 SMBus interface to read ChargingVoltage(), Voltage(), ChargingCurrent(), Current(), Alarm() and
BatteryMode(). This information, together with thermistor
measurements allows the sequencer to select the charging battery and safely servo on voltage and current.
Charging can be accomplished only if the voltage at DCDIV
indicates that sufficient voltage is available from the input
power source, usually an AC adapter. The charge mux,
which selects the battery to be charged, is capable of
charging both batteries simultaneously. The charge mux
switch drivers are configured to allow charger current to
share between the two batteries and to prevent current
from flowing in a reverse direction in the switch. The
amount of current that each battery receives will depend
upon the relative capacity of each battery and the battery
voltage. This can result in significantly shorter charging
times (up to 50% for Li-Ion batteries) than sequential
charging of each battery.
The sequencer also selects which of the pairs of PFET
switches will provide power to the system load. If the
system voltage drops below the threshold set by the
LOPWR resistor divider, then all of the output-side PFETs
are turned on quickly. The input-side PFETs act as diodes
in this mode and power is taken from the highest voltage
source available at the DCIN, BAT1, or BAT2 inputs. The
input-side powerpath switch driver that is delivering power
then closes its input switch to reduce the power dissipation in the PFET bulk diode. In effect, this system provides
diode-like behavior from the FET switches, without the
attendant high power dissipation from diodes. The HOST
is informed of this 3-Diode mode status when it polls the
powerpath status register via the SMBus interface. High
speed powerpath switching at the LOPWR trip point is
handled autonomously.
Simultaneous discharge of both batteries is supported.
The switch drivers prevent reverse current flow in the
switches and automatically discharge both batteries into
the load, sharing current according to the relative capacity
of the batteries. Simultaneous dual discharge can increase
battery operating time by up to 10% by reducing losses in
the switches and reducing internal battery losses associated with high discharge rates.
2 The SMBus Interface
2.1 SMBus Interface Overview
The SMBus interface allows the LTC1760 to communicate
with two batteries and the SMBus Host. The SMBus
Interface supports true dual port operation by allowing the
SMBus Host to be connected to the SMBus of either
battery. The LTC1760 is able to operate as an SMBus
master or slave device.
References:
Smart Battery System Manager Specification: Revision
1.1, SBS Implementers Forum.
Smart Battery Data Specification: Revision 1.1, SBS
Implementers Forum.
Smart Battery Charger Specification: Revision 1.1, SBS
Implementers Forum
System Management Bus Specification: Revision 1.1,
SBS Implementers Forum
I2C-Bus and How to Use it: V1.0, Philips Semiconductor.
1760f
13
LTC1760
U
OPERATIO
2.2 Data Bit Definition of Supported SMBus Functions.
PRESENT_ BAT1
PRESENT_ BAT2
PRESENT_ BAT3
PRESENT_ BAT4
CHARGE_BAT2
CHARGE_BAT1
AC_PRESENT
POWER_NOT_GOOD
CALIBRATE_REQUEST_SUPPORT
CHARGING_INHIBIT
LTC_VERSION2
LTC_VERSION1
LTC_VERSION0
0
0
0
0
0
1 0/1 0
0
0
0
0
0
1
RESERVED
RESERVED
RESERVED
Status
RESERVED
RESERVED
LTC_VERSION3
TURBO
0/1 0
RESERVED
1
RESERVED
1
RESERVED
0
RESERVED
0
RESERVED
0
RESERVED
0
CONDITION_FLAG
0
RESERVED
1
RESERVED
0
RESERVED
0
RESERVED
0
RESERVED
0
RESERVED
0
RESERVED
0
RESERVED
0
POWER_OFF
BATTERY
SUPPORTED
RESERVED
8'h03
Status/
Control
BATTERY
SYSTEM
REVISION
RESERVED
7'b0001_011
8'h3c
CHARGE_BAT3
0 0/1 0/1 0 0/1 0/1 0/1 0/1 1 0/1 0/1
RESERVED
Read
7'b0001_010
CHARGE_BAT4
0
0
RESERVED
Master
Read/
Write
POWER_BY_BAT2
0
RESERVED
0 0/1 0/1
RESERVED
BatteryMode()
Slave
POWER_BY_BAT1
0
POWER_BY_BAT3
0
RESERVED
LTC()
POWER_BY_BAT4
0
CALIBRATE_REQUEST
Status
CHARGER_POR
8'h04
CALIBRATE
7'b0001_010
RESERVED
Read
Slave
CALIBRATE_BAT1
BatterySystemInfo()
RESERVED
Status/
Control
CALIBRATE_BAT2
8'h02
0 0/1 0/1 0
CALIBRATE_BAT3
7'b0001_010
0 0/1 0/1 0
RESERVED
Read/
Write
0 0/1 0/1 0
CALIBRATE_BAT4
BatterySystemStateCont() Slave
0
SMB_BAT2
Status/
Control
SMB_BAT1
8'h01
D15 D14 D13 D12 D11 D10 D09 D08 D07 D06 D05 D04 D03 D02 D01 D00
RESERVED
7'b0001_010
Data Bit or Nibble Definition/Allowed Values
(See section 2.3 for Details)
SMB_BAT3
Read/
Write
Data
Type
RESERVED
Slave
Command
Code
SMB_BAT4
BatterySystemState()
SMBus
Address
RESERVED
Function
LTC1760
SMBus
Mode Access
0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1
1760f
14
LTC1760
U
OPERATIO
IA00
IA01
IA02
IA03
IA05
IA04
IA06
IA07
IA09
D15 D14 D13 D12 D11 D10 D09 D08 D07 D06 D05 D04 D03 D02 D01 D00
IA08
Value
IA10
8'h0a
IA11
7'b0001_011
Data Bit or Nibble Definition/Allowed Values
(See section 2.3 for Details)
IA13
Data
Type
IA12
Read
Command
Code
IA15
Master
SMBus
Address
IA14
Function
Current()
LTC1760
Mode Access
0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1
VA00
VA01
VA02
VA03
VA05
VA04
VA06
VA07
VA09
VA08
VA10
Value
VA11
8'h09
VA13
7'b0001_011
VA12
Read
VA14
Master
VA15
Voltage()
0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1
IR00
IR01
IR02
IR04
IR03
IR05
IR06
IR08
IR07
IR09
IR10
Value
IR12
8'h14
IR11
7'b0001_011
IR13
Read
IR14
Master
IR15
ChargingCurrent()
VR00
VR01
VR02
VR04
VR03
VR05
VR06
Status
VR08
8'h16
VR07
7'b0001_011
VR09
Value
VR10
8'h15
VR12
Master
7'b0001_011
VR11
AlarmWarning ()
Read
VR13
Master
VR15
ChargingVoltage()
VR14
0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1
Read
RESERVED
RESERVED
RESERVED
FULLY_DISCHARGED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
OVER_TEMP_ALARM
TERMINATE_DISCHARGE_ALARM
TERMINATE_CHARGE_RESERVED
ARA_ADD02
ARA_ADD01
ARA_ADD00
Register
ARA_ADD03
N/A
ARA_ADD04
7'b0001_100
ARA_ADD05
Read
Byte
ARA_ADD06
Slave
0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1
ARA_ADD07
AlertResponse ()
see (1)
TERMINATE_CHARGE_ALARM
OVER_CHARGED
0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1
0
0
0
1
0
1
0
0
(1) Read-byte format. 'h14 is returned as the interrupt address of the LTC1760.
1760f
15
LTC1760
U
OPERATIO
2.3 Description of Supported SMBus Functions
The functions are described as follows:
• The LTC1760 autonomously changes the configuration of the battery(s) being charged (Polling only).
Function Name() (command code)
Purpose:
Description:
Used by the SMBus Host to determine the present state of
the LTC1760 and the attached batteries. It also may be
used to determine the state of the battery system after the
LTC1760 notifies the SMBus Host of a change via
SMBALERT.
A brief description of the function.
Purpose:
The purpose of the function, and an example where
appropriate.
SMBus Protocol: Read or Write Word.
SMBus Protocol: Refer to Section 2.5 and to the SMBus
specification for more details.
Input/Output: word – Refer to “Section 2.2” for bit
mapping.
Input, Output or Input/Output: A description of the data
supplied to, or returned by, the function.
SMB_BAT[4:1]
Whenever the LTC1760 encounters a valid command with
invalid data, it ACK’s the command, and ignores the invalid
data. For example, if an attempt is made to select battery
A and B to simultaneously communicate with the system
host, the LTC1760 will just ignore the request.
2.3.1 BatterySystemState() ('h01)
Description:
This function returns the present state of the LTC1760 and
allows access to individual batteries. The information is
broken into four nibbles that report:
Which battery is communicating with the SMBus Host
Which battery(s), if any, or AC is powering the system
Which battery(s) is connected to the Smart Charger
Which battery(s) is present.
The LTC1760 provides a mechanism to notify the system
whenever there is a change in its state. Specifically, the
LTC1760 provides the system with a notification whenever:
• A battery is added or removed (Polling or SMBALERT).
• AC power is connected or disconnected (Polling or
SMBALERT).
• The LTC1760 autonomously changes the configuration of the battery(s) supplying power (Polling only).
The read/write SMB_BAT[4:1] nibble is used by the SMBus
Host to select with which individual battery to communicate or to determine with which individual battery it is
communicating.
For example, an application that displays the remaining
capacity of all batteries would write to this nibble to
individually select each battery in turn and get its capacity.
Allowed values are:
'b0010: SMBus Host is communicating with Battery 2.
'b0001: SMBus Host is communicating with Battery 1.
(Power On Reset Value)
To change this nibble, set only one of the lower two bits of
this nibble high. All other values will simply be ignored.
POWER_BY_BAT[4:1]
The read only POWER_BY_BAT[4:1] nibble is used by the
SMBus Host to determine which battery(s) is powering the
system. All writes to this nibble will be ignored.
Allowed values are:
'b0011: System being powered by Battery 2 and Battery
1 simultaneously.
'b0010: System being powered by Battery 2.
'b0001: System being powered by Battery 1.
'b0000: System being powered by AC.
1760f
16
LTC1760
U
OPERATIO
CHARGE_BAT[4:1]
Purpose:
The read only CHARGE_BAT[4:1] nibble is used by the
SMBus Host to determine which, if any, battery is being
charged. All writes to this nibble will be ignored.
Used by the SMBus Host to retrieve additional state
information from the LTC1760 and the overall system
power configuration. It may also be used by the system to
prohibit any battery charging.
Allowed values are:
'b0011: Battery 2 and Battery 1 being charged.
SMBus Protocol: Read or Write Word.
'b0010: Battery 2 is being charged.
Input/Output: word - Refer to “Section 2.2” for bit
mapping
'b0001: Battery 1 is being charged.
'b0000: No Battery being charged.
An indication that multiple batteries are being charged
simultaneously does not indicate that the batteries are
being charged at the same rate or that they will complete
their charge at the same time. To actually determine when
an individual battery will be fully charged, use the
SMB_BAT[4:1] nibble to individually select the battery of
interest and read the TimeToFull() value.
PRESENT_BAT[4:1]
The read only PRESENT_BAT[4:1] nibble is used by the
SMBus Host to determine how many and which batteries
are present. All writes to this nibble will be ignored.
Allowed values are:
'b0011: Battery 2 and Battery 1 are present.
AC_PRESENT Bit
The read only AC_PRESENT bit is used to show the user
the status of AC availability to power the system. It may be
used internally by the SMBus Host in conjunction with
other information to determine when it is appropriate to
allow a battery conditioning cycle. Whenever there is a
change in the AC status, the LTC1760 asserts SMBALERT
low. In response, the system has to read this register to
determine the actual presence of AC. The LTC1760 uses
the DCDIV pin to measure the presence of AC.
Allowed values are:
'b1: The LTC1760 has determined that AC is present.
'b0: The LTC1760 has determined that AC is not present.
POWER_NOT_GOOD Bit
'b0001: Battery 1 is present.
The read only POWER_NOT_GOOD bit is used to show
that the voltage delivered to the system load is inadequate.
This is determined by the comparator on the LOPWR pin.
'b0000: No batteries are present.
Allowed values are:
'b0010: Battery 2 is present.
2.3.2 BatterySystemStateCont() ('h02)
Description:
This function returns additional state information of the
LTC1760 and provides an interface to prohibit charging.
This command also removes any requirement for the
SMBus Host to communicate directly with the charger to
obtain AC presence information. When the LTC1760 is
used, access to the charger address, 'h12, is blocked.
'b1: The LTC1760 has determined that the voltage
delivered to the system load is inadequate.
'b0: The LTC1760 has determined that the voltage
delivered to the system load is adequate.
CALIBRATE_REQUEST_SUPPORT Bit
The read only CALIBRATE_REQUEST_SUPPORT bit is
always set to indicate that the LTC1760 has a mechanism
to determine when any of the attached batteries are in need
of a calibration cycle.
1760f
17
LTC1760
U
OPERATIO
CALIBRATE_REQUEST Bit
CALIBRATE_BAT[4:1] Nibble
The read only CALIBRATE_REQUEST bit is set whenever
the LTC1760 has determined that one or more of the
connected batteries need a calibration cycle.
The read/write CALIBRATE_BAT[4:1] nibble is used by the
SMBus Host to select the battery to be calibrated or to
determine which individual battery is being calibrated.
Allowed values are:
Allowed read values are:
'b1: The LTC1760 has determined that one or both
batteries requires calibration.
'b0010: Battery 2 is being calibrated . CALIBRATE must
be 1.
'b0: The LTC1760 has determined that no batteries
require calibration.
'b0001: Battery 1 is being calibrated. CALIBRATE must
be 1.
CHARGING_INHIBIT Bit
The read/write CHARGING_INHIBIT is used by the SMBus
Host to inhibit charging or to determine if charging is
inhibited. This bit is also set if MODE is used to inhibit
charging.
Allowed values are:
'b1: The LTC1760 must not allow any battery charging
to occur.
'b0: The LTC1760 may charge batteries as needed,
(Power On Reset Value).
'b0000: No batteries are being calibrated.
Allowed write values are:
'b0010: Select Battery 2 for calibration.
'b0001: Select Battery 1 for calibration.
'b0000: Allow LTC1760 to choose battery
to be calibrated.
All other values will simply be ignored. This provides a
mechanism to update the other BatterySystemStateCont()
bits without altering this nibble.
CHARGER_POR Bit
2.3.3 BatterySystemInfo ()('h04)
The read/write CHARGER_POR bit is used to force a
charger power on reset.
Description:
Writing a 1 to this bit will cause a charger power on reset
with the following effects.
The SMBus Host uses this command to determine the
capabilities of the LTC1760.
Purpose:
• Charging will be turned off and wake-up charging will
be resumed. This is the same as if the batteries were
removed and then reinserted.
Allows the SMBus Host to determine the number of
batteries the LTC1760 supports as well as the specification revision implemented by the LTC1760.
• The three minute wake-up watchdog timer will be
restarted.
SMBus Protocol: Read Word
Writing a 0 to this bit has no effect.
Input/Output: word — Refer to “Section 2.2” for bit
mapping.
A read of this bit always returns a 0.
BATTERIES_SUPPORTED Nibble
CALIBRATE Bit
The read only BATTERIES_SUPPORTED nibble is used by
the SMBus Host to determine how many batteries the
LTC1760 can support. The two-battery LTC1760 always
returns 'b0011 for this nibble.
The read/write CALIBRATE bit is used either to show the
status of battery calibration cycles in the LTC1760 or to
begin or end a calibration cycle.
1760f
18
LTC1760
U
OPERATIO
BATTERY_SYSTEM_REVISION Nibble
2.3.5 BatteryMode() ('h03)
The read only BATTERY_SYSTEM_REVISION nibble reports the version of the Smart Battery System Manager
specification supported.
Description:
LTC1760 returns 'b1000 for this nibble, indicating Version
1.0 without optional PEC support.
Purpose:
2.3.4 LTC() ('h3c)
Description:
This function returns the LTC Version nibble and allows
the user to perform expanded Smart Battery System
Manager functions.
This function is used by the LTC1760 to read the Battery
Mode register.
Allows the LTC1760 to determine if a battery requires a
conditioning/calibration cycle.
SMBus Protocol: Read Word. LTC1760 reads Battery 1 or
Battery 2 as an SMBus Master.
Input/Output: word — Refer to “Section 2.2” for bit
mapping.
Purpose:
CONDITION_FLAG Bit
Used by the SMBus Host to determine the version of the
LTC1760 and to program and monitor TURBO and
POWER_OFF special functions.
The CONDITION_FLAG bit is set whenever the battery
requires calibration.
SMBus Protocol: Read or Write Word.
Input/Output: word — Refer to “Section 2.2” for bit
mapping.
Allowed values:
'b1 - Battery requires calibration. (Also known as a
Condition Cycle Request).
'b0 - Battery does not require calibration.
POWER_OFF Bit
This read/write bit allows the LTC1760 to turn off all power
path sources.
Allowed values:
'b1: All power path sources are off.
'b0: All power path sources are enabled. (Power
On Reset Value).
2.3.6 Voltage() ('h09)
Description:
This function is used by the LTC1760 to read the actual
cell-pack voltage .
Purpose:
TURBO Bit
Allows the LTC1760 to determine the cell pack voltage and
close the charging voltage servo loop.
This read/write bit allows the LTC1760 to enter TURBO
charging mode.
SMBus Protocol: Read Word. LTC1760 reads Battery 1 or
Battery 2 as an SMBus Master.
Allowed values:
Output: unsigned integer — battery terminal voltage in
milli-volts. Refer to "Section 2.2" for bit mapping.
'b1: Turbo Charging mode enabled.
'b0: Turbo Charging mode disabled. (Power On Reset
Value).
Units: mV.
Range: 0 to 65,535 mV.
LTC_Version[3:0] Nibble
This read only nibble always returns 'b0001 as the LTC1760
version.
1760f
19
LTC1760
U
OPERATIO
2.3.7 Current() ('h0a)
Purpose:
Description:
Allows the LTC1760 to determine the maximum charging
voltage.
This function is used by the LTC1760 to read the actual
current being supplied through the battery terminals.
Purpose:
SMBus Protocol: Read Word. LTC1760 reads Battery 1 or
Battery 2 as an SMBus Master.
Allows the LTC1760 to determine how much current a
battery is receiving through its terminals and close the
charging current servo loop.
Output: unsigned integer — charger output voltage in mV.
Refer to Section 2.2 for bit mapping.
SMBus Protocol: Read Word. LTC1760 reads Battery 1 or
Battery 2 as an SMBus Master.
Range: 0 to 65,534 mV.
Output: signed integer (2’s complement) — charge/discharge rate in mA increments - positive for charge, negative for discharge. Refer to "Section 2.2" for bit mapping.
Units: mA.
Range: 0 to 32,767 mA for charge or 0 to -32,768 mA for
discharge.
2.3.8 ChargingCurrent() ('h14)
Description:
This function is used by the LTC1760 to read the Smart
Battery’s desired charging current.
Purpose:
Allows the LTC1760 to determine the maximum charging
current.
SMBus Protocol: Read Word. LTC1760 reads Battery 1 or
Battery 2 as an SMBus Master.
Output: unsigned integer — maximum charger output
current in mA. Refer to "Section 2.2" for bit mapping.
Units: mA.
Range: 0 to 65,534 mA.
Units: mV.
2.3.10 AlarmWarning () ('h16)
Description:
This function is used by the LTC1760 to read the Smart
Battery alarm register.
Purpose:
Allows the LTC1760 to determine the state of all applicable
alarm flags.
SMBus Protocol: Read Word. LTC1760 reads Battery 1 or
Battery 2 as an SMBus Master.
Output: unsigned integer – Refer to “Section 2.2” for bit
mapping.
OVER_CHARGED_ALARM Bit
The read only OVER_CHARGED_ALARM bit is used by the
LTC1760 to determine if charging may continue.
Allowed values are:
'b1: The LTC1760 will not charge this battery.
'b0: The LTC1760 may charge this battery if other
conditions permit charging.
TERMINATE_CHARGE_ALARM Bit
2.3.9 ChargingVoltage() ('h15)
The read only TERMINATE_CHARGE_ALARM bit is used
by the LTC1760 to determine if charging may continue.
Description:
Allowed values are:
This function is used by the LTC1760 to read the Smart
Battery’s desired charging voltage.
'b1: The LTC1760 will not charge this battery.
'b0: The LTC1760 may charge this battery if other
conditions permit charging.
1760f
20
LTC1760
U
OPERATIO
TERMINATE_CHARGE_RESERVED Bit
The read only TERMINATE_CHARGE_RESERVED bit is
used by the LTC1760 to determine if charging may continue.
Allowed values are:
'b0: The LTC1760 may continue discharging this
battery.
2.3.11 AlertResponse ()
Description:
'b1: The LTC1760 will not charge this battery.
The SMBus Host uses the Alert Response Address (ARA)
to quickly identify the generator of an SMBALERT# event.
'b0: The LTC1760 may charge this battery if other
conditions permit charging.
Purpose:
OVER_TEMP_ALARM Bit
The read only OVER_TEMP_ALARM is used by the LTC1760
to determine if charging may continue.
Allowed values are:
'b1: The LTC1760 will not charge this battery.
'b0: The LTC1760 may charge this battery if other
conditions permit charging.
TERMINATE_DISCHARGE_ALARM Bit
The read only TERMINATE_DISCHARGE_ALARM bit is
used by the LTC1760 to determine if discharge from the
battery is still allowed. This is used for power path management and battery calibration.
Allowed values are:
'b1: The LTC1760 will terminate calibration and should
try to not use this battery in the power path. When all
other power paths fail the LTC1760 will ignore this
alarm and still try to supply system power from this
source.
'b0: The LTC1760 may continue discharging this
battery.
FULLY_DISCHARGED Bit
The read only FULLY_DISCHARGED bit is used by the
LTC1760 to determine if discharge from the battery is still
allowed. This is used for power path management and
battery calibration.
Allowed values are:
'b1: The LTC1760 will terminate calibration and should
try to not use this battery in the power path. When all
other power paths fail the LTC1760 will ignore this
alarm and still try to supply system power from this
source.
The LTC1760 will respond to an ARA if the SMBALERT
signal is actively pulling down the SMBALERT# bus. The
LTC1760 will follow the prioritization reporting as defined
in the “System Management Bus Specification”.
SMBus Protocol: A 7-bit Addressable Device Responds to
an ARA.
Output:
The device address will be sent to the SMBus Host. The
LTC1760 device address is 0x14 (or 0x0a if just looking at
the 7 bit address field).
The following events will cause the LTC1760 to pull-down
the SMBALERT# bus through the SMBALERT pin:
• Change of AC_PRESENT in the
BatterySystemStateCont() function.
• Change of BATTERY_PRESENT in the
BatterySystemState() function.
• Internal power on reset condition.
Refer to "Section 2.2" for bit mapping.
2.4 SMBus Dual Port Operation
The SMBus Interface includes the LTC1760’s SMBus
controller, as well as circuitry to arbitrate and connect the
battery and SMBus Host interfaces. The SMBus controller
generates and interprets all LTC1760 SMBus functions.
The dual port operation allows the SMBus Host to be
connected to the SMBus of either battery by setting the
SMB_BAT[4:1] nibble. Arbitration is handled by stretching an SMBus start sequence when a bus collision might
occur. Whenever configurations are switched, the LTC1760
will generate a harmless SMBus reset on SMB1 and SMB2
as required. The four possible configurations are illustrated in Figure 1. Sample SMBus communications are
shown in Figures 2 and 3.
1760f
21
LTC1760
U
OPERATIO
SMB2*
HOST
SMB*
SMB2*
BAT2
SMB*
HOST
SMB1*
LTC1760
SMBus
CONTROLLER
SMB1*
BAT1
LTC1760
SMBus
CONTROLLER
HOST, LTC1760 AND BAT1 CAN COMMUNICATE.
BAT2 ORIGINATED COMMANDS ARE IGNORED.
BAT1
LTC1760 AND BAT2 CAN COMMUNICATE. HOST AND
BAT1 ORIGINATED COMMANDS ARE STRETCHED IF
THE LTC1760 IS COMMUNICATING WITH BAT2.
(1a)
(1b)
SMB2*
HOST
BAT2
SMB*
SMB2*
BAT2
SMB*
HOST
SMB1*
LTC1760
SMBus
CONTROLLER
SMB1*
BAT1
HOST, LTC1760 AND BAT2 CAN COMMUNICATE.
BAT1 ORIGINATED COMMANDS ARE IGNORED.
LTC1760
SMBus
CONTROLLER
BAT2
BAT1
LTC1760 AND BAT1 CAN COMMUNICATE. HOST AND
BAT2 ORIGINATED COMMANDS ARE STRETCHED IF
THE LTC1760 IS COMMUNICATING WITH BAT1.
(1c)
(1d)
1760 F01
*SMB INCLUDES SCL AND SDA, SMB1 INCLUDES SCL1 AND SDA1, AND SMB2 INCLUDES SCL2 AND SDA2.
Figure 1. Switch Configurations Used by the LTC1760 for Managing Dual Port Battery Communication
2.5 LTC1760 SMBus Controller Operation
SMBus communication with the LTC1760 is handled by
the SMBus Controller, a sub-block of the SMBus Interface.
Data is clocked into the SMBus Controller block shift
register after the rising SCL edge. Data is clocked out of the
SMBus Control block shift register after the falling edge of
SCL.
The LTC1760 acting as a slave will acknowledge (ACK)
each byte of serial data. The Command byte will be
NACKed if an invalid command code is transmitted to the
LTC1760. The SMBus Controller must respond if addressed as a combined Smart Battery System Manager
(Address 14). A valid address includes a legal Read/Write
bit. The SMBus Controller will ignore invalid data although
the data transmission with the invalid data will still be
ACK’ed.
When the LTC1760, acting as a bus master receives a
NACK, it will terminate the transmission and provide a
STOP condition on the bus.
Detection of a STOP condition, power on reset, or SMBus
time-out will reset the controller to an initial state at any
time.
The LTC1760 supports ARA, Word Write and Word Read
protocols as an SMBus slave. The LTC1760 supports
Word Read protocol as an SMBus master.
Refer to “System Management Bus Specification” for
complete description of required operation and symbols.
1760f
22
SDA2
SCL2
SDA1
SCL1
SDA
SCL
SMBus
DUAL PORT
SDA2
SCL2
SDA1
SCL1
SDA
SCL
SMBus DUAL
PORT
Figure 3. LTC1760 Queries Battery 1 Followed By Battery 2 For Requested Current. (Configuration b)
Figure 2. LTC1760 Stretches Host’s Communication With Battery 1 While It Completes a Read Of Battery 2. (Configuration b)
LTC1760
U
OPERATIO
1760f
23
LTC1760
U
OPERATIO
2.6 LTC1760 SMBALERT Operation
The SMBALERT pin allows the LTC1760 to signal to the
SMBus Host that there has been a change of status.
This pin is asserted low whenever there is a change in
battery presence, AC presence or after a power on reset
event. This pin is cleared during an Alert Response or
any of the following reads:
BatterySystemState(),BatterySystemStateCont(),
BatterySystemInfo(), or LTC().
3 Charging Algorithm Overview
thermistor is reporting IDEAL-RANGE, and the battery
fails to respond to an SMBus query. This is an important
feature for handling deeply discharged NiMh batteries.
These batteries may begin to talk while being charged and
go silent once charging has stopped.
Wake-up charging is disabled if the battery thermistor is
COLD-RANGE or UNDER-RANGE and the battery has been
charged for longer than tTIMEOUT.
3.2 Wake-Up Charging Termination
3.1 Wake-Up Charging Initiation
The LTC1760 will terminate wake-up charging when any of
the following conditions are met:
The following conditions must be met in order to allow
wake-up charging:
1. Battery removal (thermistor indicating OVER-RANGE)
1. The battery thermistor must be COLD-RANGE, IDEALRANGE, or UNDER-RANGE.
2. AC must be present.
3. BatterySystemStateCont(CHARGING_INHIBIT) must be
de-asserted (or low).
4. Hardware controlled charging inhibit must be
de-asserted (MODE not low with VDDS high).
Wake-up charging initiates when a newly inserted battery
does not respond to any LTC1760 master read commands. Only one battery will wake-up charge at a time.
When two batteries are inserted and both require wake-up
charging, Battery 1 will wake-up charge first. Battery 2 will
only wake-up charge when Battery 1 terminates wake-up
charging.
Wake-up charging takes priority over controlled charging;
this prevents one battery from tying up the charger when
it would be advantageous to dual charge two deeply
discharged batteries.
The LTC1760 will attempt to reinitiate wake-up
charging on both batteries after the SMBus Host asserts
BatterySystemStateCont(CHARGER_POR) or a power on
reset event. This will reset any wake-up charging safety
timers and is equivalent to removing and reinserting both
batteries.
The LTC1760 will attempt to reinitiate wake-up charging
on a battery if the battery is not being charged, the
2. AC is removed.
3. The SMBus Host issues a calibration request by setting
BatterySystemStateCont(CALIBRATE) high.
4. Any response to an LTC1760 master read of
ChargingCurrent(), Current(), ChargingVoltage(), or Voltage(). Note that the LTC1760 ignores all writes from the
battery.
5. Any of the following AlarmWarning() bits asserted high:
OVER_CHARGED_ALARM
TERMINATE_CHARGE_ALARM
TERMINATE_CHARGE_RESERVED
OVER_TEMP_ALARM
Note that the LTC1760 ignores all writes from the battery.
Each battery’s charge alarm is cached inside the LTC1760.
This bit will be set when any of the upper four bits of the
battery’s AlarmWarning() response are set. This bit will
remain set if a subsequent AlarmWarning() fails to respond. The cached alarm will be cleared by any of the
following conditions.
a) Associated battery is removed.
b) A subsequent AlarmWarning() clears all
charge alarm bits for the associated battery.
c) A power on reset event.
d) The SMBus Host asserts
BatterySystemStateCont(CHARGER_POR) high.
1760f
24
LTC1760
U
OPERATIO
6. An SMBus Host write asserts the LTC1760
BatterySystemStateCont(CHARGING_INHIBIT) high.
5. The battery responds to an LTC1760 master read of
Alarm() with all charge alarms deasserted.
7. Hardware controlled charging inhibit is asserted (MODE
low with VDDS high).
6. The battery responds to an LTC1760 master read of
ChargingVoltage() with a non zero voltage request value.
8. The thermistor of the battery being charged indicates
COLD-RANGE and the battery has been charged for longer
than tTIMEOUT.
7. The battery responds to an LTC1760 master read of
Voltage().
9. The thermistor of the battery being charged indicates
UNDER-RANGE and the battery has been charged for
longer than tTIMEOUT.
10. The thermistor of the battery being charged indicates
HOT-RANGE.
11. Any SMBus communication line is grounded for
longer than tQUERY.
12. BatterySystemStateCont(POWER_NOT_GOOD) is
high.
13. The emergency off feature has been asserted using the
DCDIV input pin.
3.3 Wake-Up Charging Current and Voltage Limits
The wake-up charging current is fixed at IWAKE-UP for all
values of ILIMIT. Wake-up charging uses the low current
mode described in “Section 10”.
The wake-up charging voltage is not limited by the VLIMIT
function.
3.4 Controlled Charging Initiation
All of the following conditions must be met in order to
allow controlled charging of a given battery. One or both
batteries may be control charged at a time.
1. The battery thermistor must be COLD-RANGE, IDEALRANGE, or UNDER-RANGE.
2. AC must be present.
3. BatterySystemStateCont(CHARGING_INHIBIT) must be
de-asserted (or low).
8. The battery responds to an LTC1760 master read of
ChargingCurrent() with a non zero current request value.
9. The battery responds to an LTC1760 master read of
Current().
The following charging related functions are polled each
t QUERY : Alarm(), ChargingVoltage(), Voltage(),
ChargingCurrent(), and Current().
3.5 Controlled Charging Termination
The LTC1760 will terminate controlled charging when any
of the following conditions are met:
1. Battery removal, or thermistor indicating OVER-RANGE.
2. AC removal.
3. The SMBus Host issues a calibration request by setting
BatterySystemStateCont(CALIBRATE) high.
4. An LTC1760 master read of ChargingCurrent() returning a zero current request.
5. An LTC1760 master read of ChargingVoltage() returning a zero voltage request.
6. Any of the following AlarmWarning() bits asserted high:
OVER_CHARGED_ALARM
TERMINATE_CHARGE_ALARM
TERMINATE_CHARGE_RESERVED
OVER_TEMP_ALARM
Note that the LTC1760 ignores all writes from the battery.
Each battery’s charge alarm is cached inside the LTC1760.
This bit will be set when any of the upper four bits of the
battery’s AlarmWarning() response are set.
4. Hardware controlled charging inhibit must be
de-asserted (MODE not low with VDDS high).
1760f
25
LTC1760
U
OPERATIO
This bit will remain set if a subsequent AlarmWarning()
fails to respond. The cached alarm will be cleared by any
of the following conditions.
a) Associated battery is removed.
b) A subsequent AlarmWarning() clears all charge
alarm bits for the associated battery.
c) A power on reset event.
d) The SMBus Host asserts
BatterySystemStateCont(CHARGER_POR) high.
7. An SMBus Host write asserts the LTC1760
BatterySystemStateCont(CHARGING_INHIBIT) high.
8. Hardware controlled charging inhibit is asserted (MODE
low with VDDS high).
9. The SMBus of the battery being charged has stopped
acknowledging SMBus read commands for longer than
tTIMEOUT.
10. The thermistor of the battery being charged indicates
HOT-RANGE.
11. Any SMBus communication line is grounded for
longer than tQUERY.
12. BatterySystemStateCont(POWER_NOT_GOOD) is
high.
13. The emergency off feature has been asserted using the
DCDIV input pin.
Whenever changing conditions cause either battery to
stop charging, charging is stopped immediately for all
batteries and the voltage and current algorithms are reset
to zero. Charging is not resumed until all the conditions for
controlled charging are met.
3.6 Controlled Charging Current and Voltage
Programming
The LTC1760 monitors the requested and actual current in
each battery and increases the programmed current unless one of the following conditions is met:
b) The total programmed current equals the maximum
of the two requested currents + ILIMIT/32 and
LTC(TURBO) is de-asserted (or low).
c) Only one battery is charging and the programmed
current equals the requested current + ILIMIT/32.
d) The total programmed current equals ILIMIT.
The programmed current is updated every tQUERY. It is
changed by the difference between the actual and requested currents.
LTC(TURBO) provides a mechanism for the SMBus Host
to put additional current into both batteries. Normally the
LTC1760 will limit the current into both batteries to the
maximum of the two requested currents + ILIMIT/32. When
LTC(TURBO) is asserted, this restriction is removed,
allowing the charger to output as much as ILIMIT into both
batteries. Whenever changing conditions cause either
battery to stop charging, the current algorithm is reset to
zero.
The LTC1760 monitors the requested and actual voltages
in each battery and increases the programmed voltage by
16mV each tQUERY unless one of the following conditions
are met:
a) The actual voltage exceeds the requested voltage in
either battery.
b) The actual voltage exceeds VLIMIT.
This is an extremely important feature of the LTC1760
since it allows the charger to servo on the internal cell
voltage of the battery as determined by the Smart Battery.
This voltage may be significantly lower than the battery
pack terminal voltage which is used by all Level 2 chargers.
The advantage for the LTC1760 is improved charge time,
safety, and a more completely charged battery.
The voltage correction cannot exceed the minimum requested voltage by more than 512mV. When decrementing,
the programmed voltage is reduced by 16mV each tQUERY.
Whenever changing conditions cause either battery to
stop charging, the voltage algorithm is reset to zero.
a) The actual current exceeds the requested current in
either battery.
1760f
26
LTC1760
U
OPERATIO
4 System Power Management Algorithm and Battery
Calibration
4.1 Turning Off System Power
The LTC1760 allows the user to turn off system power
using the LTC(POWER_OFF) bit. When POWER_OFF is
asserted high all power management functions are bypassed and the LTC1760 will turn off DCIN, BAT2 and
BAT1 power paths. This feature allows the user to power
down the system. Charging is still allowed when
POWER_OFF is asserted high.
4.2 Power-By Algorithm When No Battery is Being
Calibrated
The LTC1760 will always attempt to maintain system
power. The preferred configuration is to remain in 3- Diode
mode. In 3-Diode mode, power will be provided by BAT1,
BAT2 and DCIN with the source at the highest voltage
potential automatically providing all the power. Sources at
similar voltage potentials will share power based on their
capacity.
The following conditions will cause the LTC1760 to modify
its preferred power-by algorithm.
1. A battery issues a terminate discharge alarm and
AC_PRESENT is high. The LTC1760 will select the other
battery and DCIN to power the system.
2. A battery issues a terminate discharge alarm and
AC_PRESENT is low. The LTC1760 will select the other
battery to power the system.
3. A battery issues a terminate discharge alarm,
AC_PRESENT is low, and the other battery is not present
or has previously alarmed. The LTC1760 will autonomously try to restore power by entering 3-Diode mode.
The 3-Diode mode will ignore TERMINATE_DISCHARGE
and FULLY_DISCHARGED alarms.
4.4 Power-By Reporting
The following tables illustrate how BatterySystem
State(POWER_BY_BAT[4:1]) interprets power path
conditions.
Power Reporting for Batteries Being Calibrated
AC_PRESENT CALIBRATE_BAT2 CALIBRATE_BAT2 POWER_BY_BAT[4:1]
1
0
0
'b0000
1
0
1
'b0001
1
1
0
'b0010
*States not shown are not allowed
Power Reporting as a Function of Battery Presence
AC_PRESENT PRESENT_BAT2 PRESENT_BAT1 POWER_BY_BAT[4:1]
1
X
X
'b0000
0
0
0
'b0000
0
0
1
'b0001
0
1
0
'b0010
0
1
1
'b0011
Power Reporting with AC_PRESENT Low and both Batteries
Present, as a Function of Power Alarms.
BATTERY 2
BATTERY 1
POWER ALARM POWER ALARM
AC_PRESENT
(NOTE 1)
(NOTE 1)
POWER_BY_BAT[4:1]
0
0
0
'b0011
0
0
1
'b0010
0
1
0
'b0001
0
1
1
'b0011
1
X
X
'b0000
Note 1: A power alarm means that ALARM() has returned
TERMINATE_DISCHARGE=1 or FULLY_DISCHARGED_ALARM=1
Power Reporting When
BatterySystemStateCont(POWER_NOT_GOOD) is High
and the LTC1760 has Autonomously Entered 3-Diode Mode
AC_PRESENT PRESENT_BAT2 PRESENT_BAT1 POWER_BY_BAT[4:1]
0
0
0
'b0000
0
0
1
'b0001
0
1
0
'b0010
4.3 Power-By Algorithm When a Battery is Being
Calibrated
0
1
1
'b0011
1
0
0
'b0000
During battery calibration, the battery being calibrated is
the only device powering the system. This will be reflected
in the reported POWER_BY[4:1] bits. See “Section 5” for
more information on battery calibration.
1
0
1
'b0000
1
1
0
'b0000
1
1
1
'b0000
1760f
27
LTC1760
U
OPERATIO
5 Battery Calibration (Conditioning)
5.2 Initiating Calibration of Selected Battery
Calibration allows the SMBus Host to fully discharge a
battery for conditioning purposes. The SMBus Host may
determine the battery to be discharged or allow the
LTC1760 to choose based on the batteries’ request to be
conditioned.
The SMBus Host initiates a calibration by writing to
BatterySystemStateCont(CALIBRATE). Follow rules of the
previous section to preserve battery intended for calibration. The SMBus Host must only set the calibration bit
once per calibration.
5.1 Selecting a Battery to be Calibrated
Option 1) SMBus Host chooses battery to be calibrated
using BatterySystemStateCont(CALIBRATE_BAT[4:1])
Allowed values:
'b0001: Set CALIBRATE_BAT1. Only has an effect if
Battery 1 BatteryMode(CONDITION_FLAG) is high .
May not be updated if a calibration is in progress.
'b0010: Set CALIBRATE_BAT2. Only has an effect if
Battery 2 BatteryMode(CONDITION_FLAG) is high.
May not be updated if a calibration is in progress.
'b0000: Clears CALIBRATE_BAT1 and
CALIBRATE_BAT2 and allows LTC1760 to chose. Power
on reset default. May not be updated if a calibration is
in progress.
Option 2) SMBus Host allows LTC1760 to choose battery
to be calibrated.
BatterySystemStateCont(CALIBRATE_BAT[4:1]) = 'b0000.
See previous option.
The LTC1760 determines that the battery requires calibration by reading BatteryMode(CONDITION_FLAG). This
flag is cached in the LTC1760. The LTC1760 sets
BatterySystemStateCont(CALIBRATE_REQUEST) high.
The LTC1760 will always select the battery that is requesting calibration. If both batteries are requesting calibration,
the LTC1760 will select Battery 1. If neither battery is
requesting calibration, then calibration cannot occur.
The LTC1760 will discharge the selected battery as long as
the calibration is in progress (CALIBRATE high). Updates
to the cached BatteryMode(CONDITION_FLAG) will be
inhibited while CALIBRATE is asserted. This means that
discharge of the battery will continue even if the battery
clears the CONDITION_FLAG.
5.3 Terminating Calibration of Selected Battery
Calibration will end when CALIBRATE is cleared. CALIBRATE will be cleared when:
• AC is removed.
• The battery being calibrated is removed. When the
battery being calibrated is removed, the LTC1760
will automatically calibrate the other battery if it is
requesting calibration.
• BatterySystemStateCont(POWER_NOT_GOOD) is
high.
• The battery sets Alarm Warning
(TERMINATE_DISCHARGE) high.
• The battery sets Alarm Warning
(FULLY_DISCHARGED) high.
• A zero is written to the CALIBRATE bit.
The LTC1760 will attempt to initiate a charge cycle after the
discharge cycle is completed.
1760f
28
LTC1760
U
OPERATIO
6 MODE Pin Operation
The MODE pin is a multifunction pin that allows the
LTC1760 to: 1) display charging status in stand alone
operation; 2) activate hardware charge inhibit; 3) charge
when SCL and SDA are low and; 4) charge with an SMBus
Host.
Summary of SDA, SCL and SMBALERT Operation as a Function
of MODE and VDDS Levels
CONDITION
LTC1760 OPERATING MODE
VMODE = VVSS
VVDDS < VILVDDS
SCL: Clock for Status Indicators
SDA: Battery 2 Status
SMBALERT: Battery 1 Status
VMODE = VVSS
VVDDS > VILVDDS
SCL, SDA, SMBALERT: Normal Operation
LTC1760 Charging Inhibited
VMODE = VVSS
VVDDS < VILVDDS
SCL, SDA Ignored and May Float Low
SMBALERT: Normal Operation
SCL1, SDA1, SCL2 and SDA2: Normal Operation and
Charging is Allowed
VMODE = VVSS
VVDDS > VILVDDS
Normal Operation on all Pins, Charging is Allowed
6.1 Stand Alone Charge Indication
When MODE is tied to GND and VVDDS < VIL_VDDS, the
function of SDA, SMBALERT, and SCL are changed as
described below.
SDA is an output and is used to monitor charging status of
Battery 2.
Allowed valued are:
Low: Battery 2 is charging.
High: Battery 2 not charging (AC is not present or
battery is not present).
Blinking: Battery 2 charge complete (AC is present,
battery is present and not charging).
SMBALERT is used to monitor charging status of Battery1. Allowed valued are:
Low: Battery 1 is charging.
High: Battery 1 not charging (AC is not present or
battery is not present).
Blinking: Battery 1 charge complete (AC is present,
battery is present and not charging).
SCL is an input and is used to determine the blinking rate
of SDA and SMBALERT. Tie SCL high if blinking is not
desired. This will provide two different states to indicate
charging (output low) and not charging (output high).
6.2 Hardware Charge Inhibit
When MODE is tied to GND and VVDDS>VIH_VDDS,charging
is inhibited and BatterySystemStateCont(CHARGING_INHIBIT)
will report a logic high.
6.3 Charging When SCL And SDA Are Low
When MODE is tied to VCC2 and VDDS < VIL_VDDS, SDA and
SCL are not used and will not interfere with LTC1760
battery communication. This feature allows the LTC1760
to autonomously charge when SCL and SDA are not
available. This scenario might occur when SMBus Host
has powered down and is no longer pulling up on SCL and
SDA.
6.4 Charging With an SMBus Host
When Mode is tied to VCC2 and VVDDS > VIL_VDDS, SDA and
SCL are used to communicate with the SMBus Host.
7 Battery Charger Controller
The LTC1760 charger controller uses a constant off-time,
current mode step-down architecture. During normal operation, the top MOSFET is turned on each cycle when the
oscillator sets the SR latch and turned off when the main
current comparator ICMP resets the SR latch. While the top
MOSFET is off, the bottom MOSFET is turned on until
either the inductor current trips the current comparator
IREV, or the beginning of the next cycle. The oscillator uses
the equation.
tOFF = (VDCIN - VBAT)/(VDCIN • fOSC)
to set the bottom MOSFET on time. The result is quasiconstant frequency operation where the converter frequency remains nearly constant over a wide range of
output voltages. This activity is diagrammed in Figure 4.
The peak inductor current, at which ICMP resets the SR
latch, is controlled by the voltage on ITH. ITH is in turn
controlled by several loops, depending upon the situation
1760f
29
LTC1760
U
OPERATIO
DCIN + 10V
(CHARGE PUMPED)
OFF
TGATE
ON
TO
BATTERY
1
tOFF
ON
BGATE
FROM
CHARGER
OFF
BAT1
–
CSN
GCH1
Q3
EAC
35mV
+
TRIP POINT SET BY ITH VOLTAGE
SCH1
+
INDUCTOR
CURRENT
CC
20mV
10k
–
Figure 4.
at hand. The average current control loop converts the
voltage between CSP and BAT to a representative current.
Error amp CA2 compares this current against the desired
current programmed by the IDAC at the ISET pin and adjusts
ITH for the desired voltage across RSENSE.
The voltage at BAT is divided down by an internal resistor
divider set by the VDAC and is used by error amp EA to
decrease ITH if the divider voltage is above the 0.8V
reference.
The amplifier CL1 monitors and limits the input current,
normally from the AC adapter, to a preset level (100 mV/
RCL). At input current limit, CL1 will decrease the ITH
voltage and thus reduce battery charging current.
An over-voltage comparator, OV, guards against transient
overshoots (>7.5%). In this case, the top MOSFET is
turned off until the over-voltage condition is cleared. This
feature is useful for batteries which “load dump” themselves by opening their protection switch to perform
functions such as calibration or pulse-mode charging.
The top MOSFET driver is powered from a floating bootstrap capacitor C4. This capacitor is normally recharged
from VCC through an external diode when the top MOSFET
is turned off. As VIN decreases towards the selected
battery voltage, the converter will attempt to turn on the
top MOSFET continuously (“dropout’’). A dropout timer
detects this condition and forces the top MOSFET to turn
off, and the bottom MOSFET on, for about 200ns at 40µs
intervals to recharge the bootstrap capacitor.
7.1 Charge MUX Switches
The equivalent circuit of a charge MUX switch driver is
shown in Figure 5. If the charger controller is not enabled,
the charge MUX drivers will drive the gate and source of
Q4
OFF
1760 F05
Figure 5. Charge MUX Switch Driver Equivalent Circuit
the series connected MOSFETs to a low voltage and the
switch is off. When the charger controller is on, the charge
MUX driver will keep the MOSFETs off until the voltage at
CSN rises at least 35mV above the battery voltage. GCH1
is then driven with an error amplifier EAC until the voltage
between BAT1 and CSN satisfies the error amplifier or until
GCH1 is clamped by the internal Zener diode. The time
required to close the switch could be quite long (many ms)
due to the small currents output by the error amp and
depending upon the size of the MOSFET switch.
If the voltage at CSN decreases below VBAT1 – 20mV a
comparator CC quickly turns off the MOSFETs to prevent
reverse current from flowing in the switches. In essence,
this system performs as a low forward voltage diode.
Operation is identical for BAT2.
7.2 Dual Charging
Note that the charge MUX switch drivers will operate
together to allow both batteries to be charged simultaneously. If both charge MUX switch drivers are enabled,
only the battery with the lowest voltage will be charged
until its voltage rises to equal the higher voltage battery.
The charge current will then share between the batteries
according to the capacity of each battery.
When batteries are controlled charging, only batteries
with voltages above VCHMIN are allowed to charge. When
a battery is wake-up charging this restriction does not
apply.
1760f
30
LTC1760
U
OPERATIO
8 PowerPath Controller
8.1 Autonomous PowerPath Switching
The PowerPath switches are turned on and off by the
power management algorithm. The external PFETs are
usually connected as an input switch and an output switch.
The output switch PFET is connected in series with the
input PFET and the positive side of the short-circuit
sensing resistor, RSC. The input switch is connected in
series between the power source and the output PFET. The
PowerPath switch driver equivalent circuit is shown in
Figure 6. The output PFET is driven ON or OFF by the output
side driver controlling pin GB10. The gate of the input PFET
is driven by an error amplifier which monitors the voltage
between the input power source (BAT1 in this case) and
SCP. If the switch is turned off, the two outputs are driven
to the higher of the two voltages present across the
input/SCP terminals of the switch. When the switch is
instructed to turn on, the output side driver immediately
drives the gate of the output PFET approximately 6V below
the highest of the voltages present at the input/SCP. When
the output PFET turns on, the voltage at SCP will be pulled
up to a diode drop below the source voltage by the bulk
diode of the input PFET. If the source voltage is more than
25mV above SCP, EAP will drive the gate of the input PFET
low until the input PFET turns on and reduces the voltage
across the input/SCP to the EAP set point, or until the
Zener clamp engages to limit the voltage applied to the
input PFET. If the source voltage drops more than 20mV
below SCP, then comparator CP turns on SWP to quickly
prevent large reverse current in the switch. This operation
mimics a diode with a low forward voltage drop.
The LOPWR comparator monitors the voltage at the load
through the resistor divider from pin SCN. If LTC
(POWER_OFF) is low and the LOPWR comparator trips,
then all of the switches are turned on (3-Diode mode) by
the Autonomous PowerPath Controller to ensure that the
system is powered from the source with the highest voltage. The Autonomous PowerPath Controller waits approximately 1second, to allow power to stabilize, and then reverts back to the PowerPath switch configuration requested
by the PowerPath Management Algorithm. A power fail
counter is incremented to indicate that a failure has occurred. If the power fail counter equals a value of 3, then
the the Autonomous PowerPath Controller sets the
switches to 3-Diode mode and BatterySystemStateCont(POWER_NOT_GOOD) will be set, provided the
LOPWR comparator is still detecting a low power event. This
is a three-strikes-and-you’re-out process which is intended
to debounce the POWER_NOT_GOOD indicator. The power
fail counter is reset when battery or AC presence change.
OFF
20mV
–
CP
+
FROM
BATTERY
1
BAT1
SWP
–
Short-circuit protection operates in both a current mode
and a voltage mode. If the voltage between SCP and SCN
exceeds the short-circuit comparator threshold VTSC
for more than 15ms, then all of the PowerPath
switches are turned off and BatterySystemStateCont (POWER_NOT_GOOD) is set. Similarly, if the voltage
at SCN falls below 3V for more than 15ms, then all of
the PowerPath switches are turned off and
POWER_NOT_GOOD is set high. The POWER_NOT_GOOD
bit is reset by removing all power sources and allowing the
voltage at VPLUS to fall below the UVLO threshold. If the
POWER_NOT_GOOD bit is set, charging is disabled until
VPLUS exceeds the UVLO threshold and the Charger Algorithm allows charging to resume.
GB1I
Q7
EAP
SCP
8.2 Short-Circuit Protection
+
25mV
GB1O
Q8
OFF
CL
RSC
Figure 6. PowerPath Driver Equivalent Circuit
TO LOAD
1760 F06
When a hard short-circuit occurs, it might pull all of the
power sources down to near 0V potentials. The capacitors
on VCC and VPLUS must be large enough to keep the circuit
operating correctly during the 15ms short-circuit event.
The charger will stop within a few microseconds, leaving
a small current which must be provided by the capacitor
on VPLUS. The recommended minimum values (1µF on
1760f
31
LTC1760
U
OPERATIO
VPLUS and 2µF on VCC, including tolerances) should keep
the LTC1760 operating above the UVLO trip voltage long
enough to perform the short-circuit function when the
input voltages are greater than 8V. Increasing the capacitor across VCC to 4.7µF will allow operation down to the
recommended 6V minimum.
8.3 Emergency Turn-Off
All of the PowerPath switches can be forced off by setting
the DCDIV pin to a voltage between 8V and 10V. This will
have the same effect as a short-circuit event. DCDIV must
be less than 5V and VPLUS must decrease below the UVLO
threshold to re-enable the PowerPath switches. The
LTC1760 can recover from this condition without removing power. Contact Applications Engineering for more
information.
8.4 Power-Up Strategy
All three PowerPath switches are turned on after VPLUS
exceeds the UVLO threshold for more than 250ms. This
delay is to prevent oscillation from a turn-on transient near
the UVLO threshold.
9 The Voltage DAC Block
The voltage DAC (VDAC) is a delta-sigma modulator which
controls the effective value of an internal resistor,
RVSET = 7.2k, used to program the maximum charger
voltage. Figure 7 is a simplified diagram of the VDAC
operation. The delta-sigma modulator and switch SWV
convert the VDAC value to a variable resistance equal to
(11/8)RVSET/(VDAC(VALUE)/2047). In regulation, VSET is
servo driven to the 0.8V reference voltage, VREF.
Capacitors CB1 and CB2 are used to average the voltage
present at the VSET pin as well as provide a zero in the
voltage loop to help stability and transient response time
to voltage variations.
10 The Current DAC Block
The current DAC is a delta-sigma modulator which
controls the effective value of an internal resistor,
RSET = 18.77k, used to program the maximum charger
current. Figure 8 is a simplified diagram of the DAC operation. The delta-sigma modulator and switch convert the
IDAC value to a variable resistance equal to 1.25RSET/
(IDAC(VALUE)/1023). In regulation, ISET is servo driven to
the 0.8V reference voltage, VREF, and the current from RSET
is matched against a current derived from the voltage
between pins CSP and CSN. This current is (VCSP – VCSN)/
3k.
Therefore programmed current is:
ICHG = 0.8 VREF 3k/(RSNS RSET) • (IDAC(VALUE)/1023)
= (102.3mV/RSNS) • (IDAC(VALUE)/1023)
During wake-up current operation, the current DAC enters
a low current mode. The current DAC output is pulse-width
modulated with a high frequency clock having a duty cycle
value of 1/8. Therefore, the maximum output current provided by the charger is IMAX/8. The delta-sigma output gates
this low duty cycle signal on and off. The delta-sigma shift
registers are then clocked at a slower rate, about 40ms/bit,
so that the charger has time to settle to the IMAX/8 value.
CSN
CB2
(VCSP – VCSN)
3kΩ
(FROM CA1 AMPLIFIER)
RVF
405.3k
VSET
ISET
–
TO
ITH
EA
CB1
VREF
RVSET
7.2k
SWV
+
+
TO
ITH
CSET
RSET
18.77k
∆Σ
MODULATOR
11
DAC
VALUE
(11 BITS)
VREF
–
∆Σ
MODULATOR
10
1760 F07
Figure 7. Voltage DAC Operation
DAC
VALUE
(10 BITS)
1760 F08
Figure 8. Current Dac Operation
1760f
32
LTC1760
U
W
U U
APPLICATIO S I FOR ATIO
Automatic Current Sharing
In a dual parallel charge configuration, the LTC1760 does
not actually control the current flowing into each individual
battery. The capacity, or Amp-Hour rating, of each battery
determines how the charger current is shared. This automatic steering of current is what allows both batteries to
reach their full capacity points at the same time. In other
words, given all other things equal, charge termination will
happen simultaneously.
A battery can be modeled as a huge capacitor and hence
governed by the same laws.
I = C • (dV/dt) where:
I = The current flowing through the capacitor
C = Capacity rating of battery (using amp-hour values
instead of capacitance)
dV = Change in voltage
dt = Change in time
The equivalent model of a set or parallel batteries is a set
of parallel capacitors. Since they are in parallel, the change
in voltage over change in time is the same for both batteries
one and two.
Capacity rating will change with age and use and hence the
current sharing ratios can change over time.
Adapter Limiting
An important feature of the LTC1760 is the ability to
automatically adjust charging current to a level which
avoids overloading the wall adapter. This allows the product to operate at the same time that batteries are being
charged without complex load management algorithms.
Additionally, batteries will automatically be charged at the
maximum possible rate of which the adapter is capable.
This feature is created by sensing total adapter output
current and adjusting charging current downward if a
preset adapter current limit is exceeded. True analog
control is used, with closed loop feedback ensuring that
adapter load current remains within limits. Amplifier CL1
in Figure 9 senses the voltage across RCL, connected
between the CLP and DCIN pins. When this voltage exceeds 100mV, the amplifier will override programmed
charging current to limit adapter current to 100mV/RCL. A
lowpass filter formed by 5kΩ and 0.1µF is required to
eliminate switching noise. If the current limit is not used,
CLP should be connected to DCIN.
dV/dtBAT1 = dV/dtBAT2
100mV
–
From here we can simplify.
+
From here we solve for the actual current for each battery.
IBAT2 = ICHRG CBAT2/(CBAT1 + CBAT2)
IBAT1 = ICHRG CBAT1/(CBAT1 + CBAT2)
Please note that the actual observed current sharing will
vary from manufacturer’s claimed capacity ratings since it
is actual physical capacity rating at the time of charge.
5kΩ
+
RCL*
DCIN
IBAT2 = IBAT1 CBAT2/CBAT1
ICHRG = IBAT1 + IBAT2
0.1µF
CL1
IBAT1/CBAT1 = dV/dt = IBAT2/CBAT2
At this point you can see that the current divides as the ratio
of the two batteries capacity ratings. The sum of the
current into both batteries is the same as the current being
supply by the charger. This is independent of the mode of
the charger (CC or CV).
CLP
+
*RCL =
CIN
100mV
ADAPTER CURRENT LIMIT
AC ADAPTER
INPUT
VIN
1760 F09
Figure 9.
Setting Input Current Limit
To set the input current limit, you need to know the
minimum wall adapter current rating. Subtract 5% for the
input current limit tolerance and use that current to determine the resistor value.
RCL = 100mV/ILIM
ILIM = Adapter Min Current
– (Adapter Min Current • 5%)
1760f
33
LTC1760
U
W
U U
APPLICATIO S I FOR ATIO
As is often the case, the wall adapter will usually have at
least a +10% current limit margin and many times one can
simply set the adapter current limit value to the actual
adapter rating (see Table 1).
in currents that greatly exceed the requested value and
potentially damage the battery or overload the wall adapter
if no input current limiting is provided.
Setting Charger Output Voltage Limit
Table 1. Common RCL Resistor Values
Adapter
Rating A
RCL Value*
(Ω) 1%
RCL Power
Dissipation (W)
RCL Power
Rating (W)
1.5
0.06
0.135
0.25
1.8
0.05
0.162
0.25
2
0.045
0.18
0.25
2.3
0.039
0.206
0.25
2.5
0.036
0.225
0.5
2.7
0.033
0.241
0.5
3
0.030
0.27
0.5
*Values shown above are rounded to nearest standard value.
Extending System to More than 2 Batteries
The LTC1760 can be extended to manage systems with
more than 3 sources of power. Contact Linear Technology
Applications Engineering for more information.
Charge Termination Issues
Batteries with constant-current charging and voltagebased charger termination might experience problems
with reductions of charger current caused by adapter
limiting. It is recommended that input limiting feature be
defeated in such cases. Consult the battery manufacturer
for information on how your battery terminates charging.
Setting Charger Output Current Limit
The LTC1760 current DAC and the PWM analog circuitry
must coordinate the setting of the charger current. Failure
to do so will result in incorrect charge currents.
Table 2. Recommended Resistor Values
IMAX (A)
RSENSE (Ω) 1%
RSENSE (W)
RILIM (Ω) 1%
1
0.100
0.25
0
2
0.05
0.25
10k
3
0.025
0.5
33k
4
0.025
0.5
Open
Warning
DO NOT CHANGE THE VALUE OF RILIM DURING OPERATION. The value must remain fixed and track the RSENSE
value at all times. Changing the current setting can result
The value of an external resistor connected from the VLIMIT
pin to GND determines one of five voltage limits that are
applied to the charger output value. See Table 3. These
limits provide a measure of safety with a hardware restriction on charging voltage, which cannot be overridden by
software. This voltage sets the limit that will be applied to
the battery as reported by battery. Since the battery
internal voltage monitor point is the actual cell voltage, you
may see higher voltages, up to 512mV higher, at the
external charger terminals due to the voltage servo loop
action. See Operations section 3.6 for more information
on the voltage servo system.
Table 3. Recommended Resistor Values for RVLIM
VMAX
RVLIM ± 1%
Up to 8.4V
0Ω (Short to ground)
Up to 12.6V
10k
Up to 16.8V
33k
Up to 21.0V
100k
Up to 32.7V (No Limit)
Open (or short to VCC2)
Inductor Selection
Higher operating frequencies allow the use of smaller
inductor and capacitor values. A higher frequency generally results in lower efficiency because of MOSFET gate
charge losses. In addition, the effect of inductor value on
ripple current and low current operation must also be
considered. The inductor ripple current ∆IL decreases
with higher frequency and increases with higher VIN.
∆IL =
⎛ V ⎞
VOUT ⎜ 1 − OUT ⎟
VIN ⎠
⎝
f L
1
( )( )
Accepting larger values of ∆IL allows the use of low
inductances, but results in higher output voltage ripple
and greater core losses. A reasonable starting point for
setting ripple current is ∆IL = 0.4(IMAX). In no case should
∆IL exceed 0.6(IMAX) due to limits imposed by IREV and
1760f
34
LTC1760
U
W
U U
APPLICATIO S I FOR ATIO
CA1. Remember the maximum ∆IL occurs at the maximum input voltage. In practice 10µH is the lowest value
recommended for use.
Charger Switching Power MOSFET and Diode
Selection
Two external power MOSFETs must be selected for use
with the LTC1760 charger: An N-channel MOSFET for the
top (main) switch and an N-channel MOSFET for the
bottom (synchronous) switch.
The peak-to-peak gate drive levels are set by the VCC
voltage. This voltage is typically 5.2V. Consequently, logiclevel threshold MOSFETs must be used. Pay close attention to the BVDSS specification for the MOSFETs as well;
many of the logic level MOSFETs are limited to 30V or less.
Selection criteria for the power MOSFETs include the “ON”
resistance RDS(ON), reverse transfer capacitance CRSS,
input voltage and maximum output current. The LTC1760
charger is always operating in continuous mode so the
duty cycles for the top and bottom MOSFETs are given by:
Main Switch Duty Cycle = VOUT/VIN
Synchronous Switch Duty Cycle = (VIN – VOUT)/VIN
The MOSFET power dissipations at maximum output
current are given by:
PMAIN = VOUT/VIN(IMAX) 2(1 + δ∆Τ)RDS(ON) + k(VIN) 2
(IMAX)(CRSS)(f)
PSYNC = (VIN – VOUT)/VIN(IMAX)2(1 + δ∆Τ) RDS(ON)
Where δ∆Τ is the temperature dependency of RDS(ON) and
k is a constant inversely related to the gate drive current.
Both MOSFETs have I2R losses while the topside
N-channel equation includes an additional term for transition losses, which are highest at high input voltages. For
VIN < 20V the high current efficiency generally improves
with larger MOSFETs, while for VIN > 20V the transition
losses rapidly increase to the point that the use of a higher
RDS(ON) device with lower CRSS actually provides higher
efficiency. The synchronous MOSFET losses are greatest
at high input voltage or during a short-circuit when
the duty cycle in this switch is nearly 100%. The term
(1 + δ∆Τ) is generally given for a MOSFET in the form of a
normalized RDS(ON) vs Temperature curve, but δ = 0.005/°C
can be used as an approximation for low voltage MOSFETs.
CRSS is usually specified in the MOSFET characteristics.
The constant k = 1.7 can be used to estimate the contributions of the two terms in the main switch dissipation
equation.
If the LTC1760 charger is to operate in low dropout mode
or with a high duty cycle greater than 85%, then the
topside N-channel efficiency generally improves with a
larger MOSFET. Using asymmetrical MOSFETs may achieve
cost savings or efficiency gains.
The Schottky diode D1, shown in the Typical Application,
conducts during the dead-time between the conduction of
the two power MOSFETs. This prevents the body diode of
the bottom MOSFET from turning on and storing charge
during the dead-time, which could cost as much as 1% in
efficiency. A 1A Schottky is generally a good size for 4A
regulators due to the relatively small average current.
Larger diodes can result in additional transition losses due
to their larger junction capacitance. The diode may be
omitted if the efficiency loss can be tolerated.
Calculating IC Operating Current
This section shows how to use the values supplied in the
Electrical Characteristics table to estimate operating current for a given application.
The total IC operating current through DCIN when AC is
present and batteries are charging (IDCIN_CHG) is given by:
IDCIN_CHG = ICH1 + IVCC2_AC1 + ISAFETY1 + ISAFETY2 +
IVLIM + IILIM + ISMB + ISMB_BAT1 + ISMB_BAT2 + ISMBALERT
where:
ICH1 is defined in “Electrical Characteristics.”
IVCC2_AC1 is defined in “Electrical Characteristics.”
ISAFETYX is the current used to test the battery thermistor
connected to SAFETY1 OR SAFETY2.
For thermistors that are OVER-RANGE:
ISAFETYX = 2/64 • VVCC2/(RXB + RTHX)
For thermistors that are COLD-RANGE:
ISAFETYX = 4/64 • VVCC2/(RXB + RTHX)
1760f
35
LTC1760
U
W
U U
APPLICATIO S I FOR ATIO
For thermistors that are IDEAL-RANGE:
ISAFETYX = 4/64 • VVCC2/(RXB + RTHX) + 2/64 • VVCC2/
(R1A +RTHX)
For thermistors that are HOT-RANGE:
ISAFETYX = 4/64 • VVCC2/(RXB + RTHX) + 4/64 • VVCC2/
(R1A +RTHX)
RTHX is the impedance of the battery’s thermistor to
ground.
RXB = 54.9k
IDCIN_CHG = ICH1 + IVCC2_AC1 + ISAFETY1 + ISAFETY2 +
IVLIM + IILIM + ISMB + ISMB_BAT1 + ISMB_BAT2 +
ISMBALERT
= 1.3mA + 700µA + 218µA + 218µA +81µA + 81µA
+ 0µA + 5.4µA + 5.4µA + 0µA = 2.62mA
The total operating current through BAT1 and BAT2 when
AC is not present (IBAT_NOAC) is given by:
IBAT_NOAC = IBAT + IVCC2_AC0 + ISAFETY1 + ISAFETY2 +
ISMB + ISMB_BAT1_AC0 + ISMB_BAT2_AC0 + ISMBALERT
where:
RXA = 1.13k
Sample calculation of ISAFETYX with VVCC2 = 5.2V
IBAT is defined in “Electrical Characteristics.”
IVCC2_AC0 is defined in “Electrical Characteristics.”
Thermistor Impedance
RTHX (Ω)
Thermistor Range
ISAFETYX (µA)
100k
OVER_RANGE
1.05
3.3k
IDEAL_RANGE
42.2
400
UNDER_RANGE
218
ISAFETYX is the current used to test the battery
thermistor connected to SAFETY1 or SAFETY2.
ISAFETYX = 2/64 • VVCC2/(RXB + RTHX).
IVLIM = VVCC2/(RVLIMIT + RLIM_PU).
RTHX is the impedance of the battery’s thermistor to
ground.
IILIM = VVCC2/(RILIMIT + RLIM_PU).
RXB = 54.9k.
RLIM_PU is the typical pull-up impedance at VLIMIT
and ILIMIT.
RLIM_PU = 34k.
RVLIMIT is the value of the resistance from VLIMIT to
GND.
RILIMIT is the value of the resistance from ILIMIT to
GND.
ISMB is the current used for communicating with the
SMBus Host and depends on the amount of bus
traffic.
ISMB_BATX is the current used for communicating
with Battery1 or Battery2.
ISMB_BATX = 350µA • 0.0155 = 5.425µA.
ISMBALERT is defined in “Electrical Characteristics.”
Sample calculation of IDCIN_CHG with two Li-Ion batteries
(RTHX = 400), RVLIMIT = RILIMIT = 30k, VCC2 = 5.2V, and no
SMBus Host communication:
Sample calculation of ISAFETY with VVCC2 = 5.2V
Thermistor Impedance
RTHX (Ω)
Thermistor Range
ISAFETYX (µA)
400
UNDER_RANGE
2.9
ISMB_BATX_ACO is the current used for communicating with Battery1 or Battery2 when AC in not present.
ISMB_BATX_AC0 = 350µA • 0.00687 = 2.404µA.
ISMB is the current used for communicating with the
SMBus Host and depends on the amount of bus
traffic.
Sample calculation with two Li-Ion batteries (RTHX =
400), VCC2 = 5.2V, and no SMBus Host communication:
IBAT_NOAC – IBAT + IVCC2_AC0 + ISAFETY1 + ISAFETY2 +
ISMB + ISMB_BAT1_AC0 + ISMB_BAT2_AC0 + ISMBALERT
= 175µA + 80µA + 2.9µA + 2.9µA + 0µA + 2.4µA +
2.4µA + 0µA = 265µA
1760f
36
LTC1760
U
W
U U
APPLICATIO S I FOR ATIO
Calculating IC Power Dissipation
The power dissipation of the LTC1760 is dependent upon
the gate charge of QTG and QBG.(Refer to Typical
Application). The gate charge is determined from the
manufacturer’s data sheet and is dependent upon both the
gate voltage swing and the drain voltage swing of the FET.
PD = (VDCIN – VVCC) • fOSC • (QTG + QBG) + VDCIN •
IDCIN_CHG – VVCC • (ISAFETY1 + ISAFETY2)
where:
IDCIN_CHG, ISAFETY1, ISAFETY2 are defined in the
previous section.
Example:
∆VVSET =
VREF • T∆ ∑
VSET/ISET Capacitors
Capacitor C7 is used to filter the delta-sigma modulation
frequency components to a level which is essentially DC.
Acceptable voltage ripple at ISET is about 10mVP-P. Since
the period of the delta-sigma switch closure, T∆Σ, is about
10µs and the internal IDAC resistor, RSET, is 18.77k, the
ripple voltage can be approximated by:
VREF • T∆ ∑
RSET • C 7
Then the equation to extract C7 is:
VREF • T∆ ∑
∆VISET • RSET
= 0.8/0.01/18.77k(10µs) ≅ 0.043µF
In order to prevent overshoot during start-up transients
the time constant associated with C7 must be shorter than
the time constant of C5 at the ITH pin. If C7 is increased to
improve ripple rejection, then C5 should be increased
proportionally and charger response time to average current variation will degrade.
C7 =
Capacitors CB1 and CB2 are used to filter the VDAC deltasigma modulation frequency components to a level which
(
RVSET C B1 || C B2
)
Then the equation to extract CB1 || CB2 is:
C B1 || C B2 =
VVCC = 5.2V, VDCIN = 19V, fOSC = 345kHz, QTG =
QBG = 15nC, IDCIN_CHG = 2.62mA, ISAFETY1 =
ISAFETY2 = 218µA.
PD = 190mW
∆VISET =
is essentially DC. CB2 is the primary filter capacitor and
CB1 is used to provide a zero in the response to cancel the
pole associated with CB2. Acceptable voltage ripple at VSET
is about 10mVP-P. Since the period of the delta-sigma
switch closure, T∆Σ, is about 11µs and the internal VDAC
resistor, RVSET, is 7.2kΩ, the ripple voltage can be approximated by:
VREF • T∆ ∑
RVSET ∆VVSET
CB2 should be 10× to 20× CB1 to divide the ripple voltage
present at the charger output. Therefore CB1 = 0.01µF and
CB2 = 0.1µF are good starting values. In order to prevent
overshoot during start-up transients the time constant
associated with CB2 must be shorter than the time constant
of C5 at the ITH pin. If CB2 is increased to improve ripple
rejection, then C5 should be increased proportionally and
charger response time to voltage variation will degrade.
Input and Output Capacitors
In the 4A Lithium Battery Charger (Typical Application
section), the input capacitor (CIN) is assumed to absorb all
input switching ripple current in the converter, so it must
have adequate ripple current rating. Worst-case RMS
ripple current will be equal to one half of output charging
current. Actual capacitance value is not critical. Solid
tantalum low ESR capacitors have high ripple current
rating in a relatively small surface mount package, but
caution must be used when tantalum capacitors are used
for input or output bypass. High input surge currents can
be created when the adapter is hot-plugged to the charger
or when a battery is connected to the charger. Solid
tantalum capacitors have a known failure mechanism
when subjected to very high turn-on surge currents. Only
Kemet T495 series of “Surge Robust” low ESR tantalums
are rated for high surge conditions such as battery to
ground.
1760f
37
LTC1760
U
W
U U
APPLICATIO S I FOR ATIO
The relatively high ESR of an aluminum electrolytic for
C15, located at the AC adapter input terminal, is helpful in
reducing ringing during the hot-plug event. Refer to AN88
for more information.
Highest possible voltage rating on the capacitor will minimize problems. Consult with the manufacturer before use.
Alternatives include new high capacity ceramic (at least
20µF) from Tokin, United Chemi-Con/Marcon, et al. Other
alternative capacitors include OSCON capacitors from
Sanyo.
The output capacitor (COUT) is also assumed to absorb
output switching current ripple. The general formula for
capacitor current is:
(
0.29 (VBAT) 1 –
IRMS =
VBAT
VDCIN
)
(L1)(f)
Selection criteria for the power MOSFETs include the “ON”
resistance RDS(ON), input voltage and maximum output
current. For the N-channel charge path, the maximum
current is the maximum programmed current to be used.
For the P-channel discharge path maximum current typically occurs at end of life of the battery when using only
one battery. The upper limit of RDS(ON) value is a function
of the actual power dissipation capability of a given
MOSFET package that must take into account the PCB
layout. As a starting point, without knowing what the PCB
dissipation capability would be, derate the package power
rating by a factor of two.
RDS(ON)MAX =
EMI considerations usually make it desirable to minimize
ripple current in the battery leads, and beads or inductors
may be added to increase battery impedance at the 300kHz
switching frequency. Switching ripple current splits between the battery and the output capacitor depending on
the ESR of the output capacitor and the battery impedance. If the ESR of COUT is 0.2Ω and the battery impedance
is raised to 4Ω with a bead or inductor, only 5% of the
current ripple will flow in the battery.
Power Path and Charge MUX MOSFET Selection
Three pairs of P-channel MOSFETs must be used with the
wall adapter and the two battery discharge paths. Two
pairs of N-channel MOSFETs must be used with the
battery charge path. The nominal gate drive levels are set
by the clamp drive voltage of their respective control
circuitry. This voltage is typically 6.25V. Consequently,
logic-level threshold MOSFETs must be used. Pay close
attention to the BVDSS specification for the MOSFETs as
well; many of the logic level MOSFETs are limited to 30V
or less.
2
( )
2 IMAX
If you are using a dual MOSFET package with both MOSFETs
in series, you must cut the package power rating in half
again and recalculate.
For example:
VDCIN = 19V, VBAT = 12.6V, L1 = 10µH, and
f = 300kHz, IRMS = 0.41A.
PMOSFET
RDS(ON)MAX =
PMOSFETDUAL
2
( )
4 IMAX
If you use identical MOSFETs for both battery paths,
voltage drops will track over a wide current range. The
LTC1760 linear 25mV CV drop regulation will not occur
until the current has dropped below:
ILINEARMAX =
25mV
2 RDS(ON)MAX
However, if you try to use the above equation to determine
RDS(ON) to force linear mode at full current, the MOSFET
RDS(ON) value becomes unreasonably low for MOSFETs
available at this time. The need for the LTC1760 voltage
drop regulation only comes into play for parallel battery
configurations that terminate charge or discharge using
voltage. At first this seems to be a problem, but there are
several factors helping out:
1. When batteries are in parallel current sharing, the
current flow through any one battery is less than if it is
running stand-alone.
2. Most batteries that charge in constant voltage mode,
such as Li-ion, charge terminate at a current value of
1760f
38
LTC1760
U
W
U U
APPLICATIO S I FOR ATIO
C/10 or less which is well within the linear operation
range of the MOSFETs.
3. Voltage tracking for the discharge process does not
need such precise voltage tracking values.
The LTC1760 has two transient conditions that force the
discharge path P-channel MOSFETs to have two additional
parameters to consider. The parameters are gate charge
QGATE and single pulse power capability.
When the LTC1760 senses a LOW_POWER event, all the
P-channel MOSFETs are turned on simultaneously to
allow voltage recovery due to a loss of a given power
source. However, there is a delay in the time it takes to turn
on all the MOSFETs. Slow MOSFETs will require more bulk
capacitance to hold up all the system’s power supply
function during the transition and fast MOSFET will require
less bulk capacitance. The transition speed of a MOSFET
to an on or off state is a direct function of the MOSFET gate
charge.
adapter path with wall adapters of high voltage, large bulk
capacitance and low resistance DC cables between the
adapter and device are the most common failures.
Remember to only use the real wall adapter with a production DC power cord when performing the wall adapter path
test. The use of a laboratory power supply is unrealistic for
this test and will force you to over specify the MOSFET
ratings. A battery pack usually has enough series resistance to limit the peak current or are too low in voltage to
create enough instantaneous power to damage their respective power path MOSFETs.
Conditioning Systems With Large Loads
In systems where the load is too large to be used for
conditioning a single battery it may be necessary to
bypass the built in calibrate function and simply switch in
an external load. A convenient way to accomplish this task
is by using an SMBus based LTC1623 load switch controller. See Figure 10.
t = QGATE/IDRIVE
IDRIVE is the fixed drive current into the gate from the
LTC1760 and “t” is the time it takes to move that charge to
a new state and change the MOSFET conduction mode.
Hence time is directly related to QGATE. Since QGATE goes
up with MOSFETs of lower RDS(ON), choosing such
MOSFETs has a counterproductive increase in gate charge
making the MOSFET slower. Please note that the LTC1760
recovery time specification only refers to the time it takes
for the voltage to recover to the level just prior to the
LOW_POWER event as opposed to full voltage.
The single pulse current rating of MOSFET is important
when a short-circuit takes place. The MOSFET must
survive a 15ms overload. MOSFETs of lower RDS(ON) or
MOSFETs that use more powerful thermal packages will
have a high power surge rating. Using too small of a pulse
rating will allow the MOSFET to blow to the open circuit
condition instantly like a fuse. Typically there is no
outward sign of failure because it happens so fast. Please
measure the surge current for all discharge power paths
under worse case conditions and consult the MOSFET
data sheet for the limitations. Voltage sources with the
highest voltage and the most bulk capacitance are often
the biggest risk. Specifically the MOSFETs in the wall
PowerPath
MUX
TO
LOAD
LTC1760
CHARGE
MUX
SMBus
SMBus
TO/FROM
HOST
CONDITIONING
LOAD
LTC1623
1760 F10
Figure 10
Unique Configuration Information
This section summarizes unique LTC1760 configurations
that allow some LTC1760 features to be eliminated. These
configurations may be selected in any combination without adversely affecting LTC1760 operation. Refer to the
Typical Application circuit diagram located at the back of
this data sheet.
1760f
39
LTC1760
U
W
U U
APPLICATIO S I FOR ATIO
A) Single Battery Configuration.
To limit the LTC1760 to a single battery, modify the battery
slot to be eliminated as follows:
5) Remove all components connected to COMP1, VSET,
ITH, ISET, ILIMIT and VLIMIT pins.
6) Short ILIMIT and VLIMIT to VSS.
1) Remove both FETs (Q5, Q6 or Q7, Q8) involved in the
charge path.
6) Remove R1, C1 but short CLP to DCIN. Replace RCL
with a short/trace connection.
2) Remove both FETS (Q3, Q4 or Q9, Q10) involved in
the discharge path.
7) Short CSP to CSN but leave the combination floating.
3) Remove the thermistor sensing resistors (R1A, R1B
or R2A, R2B).
4) Short the thermistor sense lines together at the IC.
5) Remove the diode (D2 or D3) as required.
6) Unless otherwise specified, leave the unused pins of
the LTC1760 floating.
8) Unless otherwise specified, leave the unused pins of
the LTC1760 floating.
F) No DC Path And No Charge Configuration.
To limit the LTC1760 to battery discharge functions only,
merge the previous two configurations with the following:
1) Remove CIN.
2) Remove resistors tied to DCDIV and ground DCDIV.
B) No Short-Circuit Protection Configuration.
1) Replace RSC with a short.
C) No LOPWR Protection.
1) Remove resistors R2 and R3 connected to LOPWR
and tie LOPWR to the VCC pin.
D) No DC Path Configuration.
To remove the DC input as part of the power path choices
to support the load:
1) Remove both FETs Q1 and Q2 involved in the DC
path.
2) Unless otherwise specified, leave the unused pins of
the LTC1760 floating.
E) No Charge Configuration.
To permanently disable the battery charger function:
1) Remove ALL FETs involved in the charge path (Q3,
Q4, Q9, Q10).
2) Remove switching FETs QTG, QBG, diode D1 and
inductor L1.
3) Remove diodes D2, D3, D4, capacitors C4, COUT and
Resistor R11 and RSENSE.
4) Reduce CIN capacitor to 0.1µF.
PCB Layout Considerations
For maximum efficiency, the switch node rise and fall
times should be minimized. To prevent magnetic and
electrical field radiation and high frequency resonant problems, proper layout of the components connected to the IC
is essential. (See Figure 11.) Here is a PCB layout priority
list for proper layout. Layout the PCB using this specific
order.
1. Input capacitors need to be placed as close as possible
to switching FET’s supply and ground connections. Shortest copper trace connections possible. These parts must
be on the same layer of copper. Vias must not be used to
make this connection.
2. The control IC needs to be close to the switching FET’s
gate terminals. Keep the gate drive signals short for a clean
FET drive. This includes IC supply pins that connect to the
switching FET source pins. The IC can be placed on the
opposite side of the PCB relative to above.
3. Place inductor input as close as possible to switching
FET’s output connection. Minimize the surface area of this
trace. Make the trace width the minimum amount needed
to support current—no copper fills or pours. Avoid running the connection using multiple layers in parallel.
Minimize capacitance from this node to any other trace or
plane.
1760f
40
LTC1760
U
W
U U
APPLICATIO S I FOR ATIO
SWITCH NODE
L1
VBAT
VIN
CIN
HIGH
FREQUENCY
CIRCULATING
PATH
D1
COUT
BAT
1760 F10
Figure 11. High-Speed Switching Path
4. Place the output current sense resistor right next to the
inductor output but oriented such that the IC’s current
sense feedback traces going to resistor are not long. The
feedback traces need to be routed together as a single pair
on the same layer at any given time with smallest trace
spacing possible. Locate any filter component on these
traces next to the IC and not at the sense resistor location.
5. Place output capacitors next to the sense resistor output
and ground.
9. A good rule of thumb for via count for a given high
current path is to use 0.5A per via. Be consistent.
10. If possible, place all the parts listed above on the same
PCB layer.
11. Copper fills or pours are good for all power connections except as noted above in Rule 3. You can also use
copper planes on multiple layers in parallel too—this
helps with thermal management and lower trace inductance improving EMI performance further.
12. For best current programming accuracy provide a
Kelvin connection from RSENSE to CSP and BAT. See
Figure 12 as an example.
It is important to keep the parasitic capacitance on the RT,
CSP and BAT pins to a minimum. The traces connecting
these pins to their respective resistors should be as short
as possible.
DIRECTION OF CHARGING CURRENT
6. Output capacitor ground connections need to feed into
same copper that connects to the input capacitor ground
before tying back into system ground.
RSNS
1760 F11
General Rules
7. Connection of switching ground to system ground or
internal ground plane should be single point. If the system
has an internal system ground plane, a good way to do this
is to cluster vias into a single star point to make the
connection.
8. Route analog ground as a trace tied back to IC ground
(analog ground pin if present) before connecting to any
other ground. Avoid using the system ground plane. CAD
trick: make analog ground a separate ground net and use
a 0Ω resistor to tie analog ground to system ground.
CSP
CSN
Figure 12. Kelvin Sensing of Charging Current
Important Safety Notes
Although every effort is made to meet and exceed all
required “SMBus Charger V1.1” safety features it is the
responsibility of the battery pack to protect itself from
excessive currents or voltages. The LTC1760 is not itself
a safety device. Consult your battery pack manufacturer
for more information.
1760f
41
LTC1760
U
TYPICAL APPLICATIO
Application for a Dual Battery System (12.6V/4A)
PowerPath MUX
VIN
C8, 1µF
RCL
0.03Ω
R1
4.99k
R4
12.7k
R5
1.21k
R7
49.9k
C3
0.012µF
C11
1800pF
VDDS
SMBALERT
RPU
SCL
RPU
SDA
VDDS
C1
0.1µF
R10, 100Ω
C1
0.1µF
RVLIMIT
10k
C9, 0.1µF
36
CLP
41
DCIN
3
BAT1
2
BAT2
LTC1760
VPLUS
GDCI
GDCO
GB1I
GB1O
GB2I
GB2O
SCP
16
SCN
DCDIV
37
LOPWR
COMP1
47
CSN
GCH2
48
CSP
SCH2
46
ITH
GCH1
45
ISET
SCH1
13
SW
V
40 SET
BOOST
V
24 CC
TGATE
VSS
BGATE
PGND
25
TH2A
V
29 CC2
TH2B
SMBALERT
18
SCL2
SCL
22
SDA2
SDA
20
TH1A
V
33 DDS
TH1B
V
32 LIMIT
SCL1
I
26 LIMIT
SDA1
MODE
BAT2
D2
1
7
6
9
8
11
10
5
4
12
34
35
14
15
42
43
44
39
38
28
27
17
21
30
31
19
23
R11
1k
Q6
Q7
Q2
Q5
Q8
RSC
0.02Ω
LOAD
R2
280k
C7
0.1µF
R9
3.3k C12
1000pF
C5
0.15µF
D1: MBR130T3
D2: IN4148 TYPE
Q1, Q2, Q5, Q6, Q7, Q8: Si4925DY
Q3, Q4, Q9, Q10, QTG, QBG: FDS6912A
CB1, 0.1µF
R6
100Ω
TH
SCL
SDA
BAT1
TH
SCL
SDA
QTG
C6
4.7µF
BAT2
R1B, 54.9k
D4
C13
0.1µF
R2A, 1.13k SAFETY 2
R1A, 1.13k SAFETY 1
CIN
20µF
L1
10µH
RSENSE
0.025Ω
C4, 0.22µF
CB2
0.47µF
CL
20µF
R3
49.9k
R2B, 54.9k
BAT1
D3
I5
I6
Q1
QBG
D1
COUT
20µF
CHARGE
MUX
Q4
Si6928
Q9
Si6928
Q3
Si6928
Q10
Si6928
1760 TA02
1760f
42
LTC1760
U
PACKAGE DESCRIPTIO
FW Package
48-Lead Plastic TSSOP (6.1mm)
(Reference LTC DWG # 05-08-1651)
48
12.40 – 12.60*
(.488 – .496)
25
0.95 ±0.10
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25
8.1 ±0.10
6.2 ±0.10
7.9 – 8.3
(.311 – .327)
1
24
0.32 ±0.05
0.50 BSC
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
RECOMMENDED SOLDER PAD LAYOUT
6.0 – 6.2**
(.236 – .244)
1.10
(.0433)
MAX
0.25
REF
0° – 8°
-T0.10 C
-C0.09 – 0.20
(.0035 – .008)
0.50
(.0197)
BSC
0.45 – 0.75
(.018 – .029)
0.17 – 0.27
(.0067 – .0106)
TYP
0.05 – 0.15
(.002 – .006)
FW48 TSSOP 0204
NOTE:
1. CONTROLLING DIMENSION: MILLIMETERS
MILLIMETERS
2. DIMENSIONS ARE IN
(INCHES)
3. DRAWING NOT TO SCALE
*DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED .152mm (.006") PER SIDE
**DIMENSIONS DO NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED .254mm (.010") PER SIDE
1760f
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
43
LTC1760
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT1571
1.5A Switching Regulator Battery Charger
500kHz or 200kHz Switching Frequency for Small Design
LTC1733
Li-Ion Linear Charger with Thermal Regulation
Will Not Overheat, Standalone Charger, Complete Charger
LT1769
2A Switching Regulator Battery Charger
Monolithic, 20-Lead TSSOP, 28-Lead SSOP Packages
LTC1960
Dual Battery Charger/Selector with SPI
11-Bit VDAC, 0.8% Voltage Accuracy, 10-Bit IDAC for 5% Current Accuracy
LTC4006
Small, High Efficiency, Fixed Voltage,
Lithium-Ion Battery Charger
Constant Current/ Constant Voltage Switching Regulator
with Termination Timer; AC Adapter Current Limit and
SafetySignal Sensor in a Small 16 Pin Package
LTC4007
High Efficiency, Programmable Voltage
Battery Charger with Termination
Complete Charger for 3- or 4-Cell Lithium-Ion Batteries,
AC Adapter Current Limit, SafetySignal Sensor and Indicator Outputs
LTC4008
High Efficiency, Programmable Voltage/
Current Battery Charger
Constant Current/ Constant Voltage Switching Regulator;
Resistor Voltage/Current Programming, AC Adapter Current
Limit and SafetySignal Sensor
LTC4100
Smart Battery Charger Controller
SMBus Rev 1.1 Compliant
1760f
44
Linear Technology Corporation
LT/TP 1004 1K • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900
●
FAX: (408) 434-0507 ● www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2003