MAXIM MAX1576

MOTOROLA
SEMICONDUCTOR
TECHNICAL
DATA
MC14489B
M u Iti-Character
lED
Display/lamp
Driver
CMOS
p SVFFiX
PLASTICOIP
CASE73$
The MC144898 is a flexible light-emitting-diode
driver which directly interfaces to individual lamps, 7-segment displays, or various combinations of
both. LEOs wired with common cathodes are driven in a multiplexed-by-5
fashion. Communication with an MCUIMPU is established through a synchronous serial port. The MC 144898 features data retention plus decode and scan
circuitry, thus relieving processor overhead. A single, current-setting resistor
is the only ancillary component required.
A single device can drive anyone of the following: a 5-digit display plus
decimals, a 4-112-digit display plus decimals and sign, or 25 lamps. A special
technique allows driving 5 112 digits; see Figure 16. A configuration register
allows the drive capability to be partitioned off to suit many additional applications. The on-chip decoder outputs 7-segment-format
numerals O to 9, hexadecimal characters A to F, plus 151etters and symbols.
The MC144898 is compatible with the Motorola SPI and National MICRO-WIRETM serial data ports. The chip's patented 8itGrabberTM registers
augment the serial interface by allowing random access without steering or
address bits. A 24-bit transfer updates the display register. Changing the configuration register requires an 8-bit transfer.
.Operating
Voltage Range of Drive Circuitry: 4.5 to 5.5 V
.Operating
Junction Temperature Range: -40° to 130°C
.Current Sources Controlled by Single Resistor Provide Anode Drive
.Low-Resistance
FET Switches Provide Direct Common Cathode Interface
.Low-Power
Mode (Extinguishes the LEDs) and Brightness Controlled via
Serial Port
.Special Circuitry Minimizes EMI when Display is Driven and Eliminates EMI
in Low-Power Mode
.Power-On
Reset (POR) Blanks the Display on Power-Up, Independent of
Supply Ramp Up Time
.May Be Used with Double-Heterojunction
LEDs for Optimum Efficiency
.Chip Complexity: 4300 Elements (FETs, Resistors, Capacitors, etc.)
BitGrabber is a trademark of Motorola Inc.
MICROWIRE is a trademark of National Semiconductor
REVO
November
2000
Corp.
PW SUFF,~
SOOPACKAGE "
CASE 7510
ORDERING
..
INFQRMATJON
MC14489BP
PlaSticDtP
MC14489BDW
SOOP~gec
BLOCK DIAGRAM
DATA IN
CLOCK
ENABLE
12
D
11
C
10
4
OSCILLATOR AND
CONTROL LOGIC
4
4
4
4
4
4
4
DATA OUT
4
PIN 3 = VDD
PIN 14 = VSS
4
NIBBLE MUX AND
DECODER ROM
5
7 a TO g
BLANK
5
4
4
BitGrabber
DISPLAY REGISTER
24 BITS
BitGrabber
CONFIGURATION REGISTER
8 BITS
POR
18
24–1/2–STAGE
SHIFT REGISTER
h
DIM/BRIGHT
ANODE DRIVERS
(CURRENT SOURCES)
BANK SWITCHES (FETs)
7
9
13
15
16
17
BANK 1 BANK 2 BANK 3 BANK 4 BANK 5
a
6
b
c
8
Rx
5 4 2 1 20 19
d e f g h
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁ
MAXIMUM RATINGS* (Voltages Referenced to VSS)
Symbol
VDD
Parameter
DC Supply Voltage
Value
Unit
– 0.5 to + 6.0
V
Vin
DC Input Voltage
– 0.5 to VDD + 0.5
V
Vout
DC Output Voltage
– 0.5 to VDD + 0.5
V
± 15
mA
Iin
Iout
IDD, ISS
TJ
RθJA
Tstg
TL
DC Input Current — per Pin
(Includes Pin 8)
mA
DC Output Current —
Pins 1, 2, 4 – 7, 19, 20 Sourcing
Sinking
– 40
10
Pins 9, 13, 15, 16, 17 Sinking
320
Pin 18
± 15
DC Supply Current, VDD and VSS Pins
Chip Junction Temperature
Device Thermal Resistance,
Junction–to–Ambient (see Thermal
Considerations section)
Plastic DIP
SOG Package
Storage Temperature
Lead Temperature, 1 mm from Case for
10 Seconds
± 350
mA
– 40 to + 130
°C
This device contains protection circuitry to
guard against damage due to high static voltages or electric fields. However, precautions
must be taken to avoid applications of any voltage higher than maximum rated voltages to this
high–impedance circuit. For proper operation,
Vin and Vout should be constrained to the range
VSS ≤ (Vin or Vout) ≤ VDD.
Unused inputs must always be tied to an appropriate logic voltage level (e.g., either VSS or
VDD). Unused outputs must be left open.
°C/W
90
100
– 65 to + 150
°C
260
°C
* Maximum Ratings are those values beyond which damage to the device may occur.
Functional operation should be restricted to the limits in the Electrical Characteristics
tables or Pin Descriptions section.
MC14489B
2
MOTOROLA
ELECTRICAL CHARACTERISTICS (Voltages Referenced to VSS, TJ = – 40° to 130°C* unless otherwise indicated)
Symbol
VDD
VDD (stby)
Parameter
Test Condition
Power Supply Voltage Range of LED Drive Circuitry
Minimum Standby Voltage
Bits Retained in Display and
Configuration Registers, Data
Port Fully Functional
VDD
V
Guaranteed
Limit
Unit
—
4.5 to 5.5
V
—
3.0
V
VIL
Maximum Low–Level Input Voltage
(Data In, Clock, Enable)
3.0
5.5
0.9
1.65
V
VIH
Minimum High–Level Input Voltage
(Data In, Clock, Enable)
3.0
5.5
2.1
3.85
V
VHys
Minimum Hysteresis Voltage
(Data In, Clock, Enable)
3.0
5.5
0.2
0.4
V
VOL
Maximum Low–Level Output Voltage
(Data Out)
Iout = 20 µA
3.0
5.5
0.1
0.1
V
Iout = 1.3 mA
4.5
0.4
VOH
Minimum High–Level Output Voltage
(Data Out)
Iout = – 20 µA
3.0
5.5
2.9
5.4
Iout = – 800 µA
4.5
4.1
Maximum Input Leakage Current
(Data In
In, Clock
Clock, Enable)
Vin = VDD or VSS
5.5
± 2.0
Vin = VDD or VSS,
TJ = 25°C only
5.5
± 0.1
iOL
Minimum Sinking Current
(a, b, c, d, e, f, g, h)
Vout = 1.0 V
4.5
0.2
mA
iOH
Peak Sourcing Current — See Figure 7 for currents up to
35 mA (a, b, c, d, e, f, g, h)
Rx = 2.0 kΩ, Vout = 3.0 V,
Dimmer Bit = High
5.0
13 to 17.5
mA
Rx = 2.0 kΩ, Vout = 3.0 V,
Dimmer Bit = Low
5.0
6 to 9
Vout = VDD (FET Leakage)
5.5
50
Vout = VDD (FET Leakage),
TJ = 25°C only
5.5
1
Vout = VSS (Protection Diode
Leakage)
5.5
1
Maximum ON Resistance
(Bank 1, Bank 2, Bank 3, Bank 4, Bank 5)
Iout = 0 to 200 mA
5.0
10
Ω
Maximum Quiescent Supply Current
Device in Low–Power Mode,
Vin = VSS or VDD, Rx in
Place, Outputs Open
5.5
100
µA
Same as Above, TJ = 25°C
5.5
20
Device NOT in Low–Power
Mode, Vin = VSS or VDD,
Outputs Open
5.5
1.5
Iin
IOZ
Ron
IDD, ISS
Iss
Maximum Output Leakage Current
(Bank 1
1, Bank 2
2, Bank 3
3, Bank 4
4, Bank 5)
Maximum RMS Operating Supply Current
(The VSS leg does not contain the Rx current component.
See Pin Descriptions.)
V
µA
µA
mA
* See Thermal Considerations section.
MOTOROLA
MC14489B
3
AC ELECTRICAL CHARACTERISTICS (TJ = – 40° to 130°C*, CL = 50 pF, Input tr = tf = 10 ns)
VDD
V
Guaranteed
Limit
Serial Data Clock Frequency, Single Device or Cascaded Devices
NOTE: Refer to Clock tw below
(Figure 1)
3.0
4.5
5.5
dc to 3.0
dc to 4.0
dc to 4.0
MHz
tPLH,
tPHL
Maximum Propagation Delay, Clock to Data Out
(Figures 1 and 5)
3.0
4.5
5.5
140
80
80
ns
tTLH,
tTHL
Maximum Output Transistion Time, Data Out
(Figures 1 and 5)
3.0
4.5
5.5
70
50
50
ns
fR
Refresh Rate — Bank 1 through Bank 5
(Figures 2 and 6)
3.0
4.5
5.5
NA
700 to 1900
700 to 1900
Hz
Cin
Maximum Input Capacitance — Data In, Clock, Enable
—
10
pF
VDD
V
Guaranteed
Limit
Unit
Symbol
fclk
Parameter
Unit
* See Thermal Considerations section.
TIMING REQUIREMENTS (TJ = – 40° to 130°C*, Input tr = tf = 10 ns unless otherwise indicated)
Symbol
Parameter
tsu, th
Minimum Setup and Hold Times, Data In versus Clock
(Figure 3)
3.0
4.5
5.5
50
40
40
ns
tsu, th,
trec
Minimum Setup, Hold, ** and Recovery Times, Enable versus Clock
(Figure 4)
3.0
4.5
5.5
150
100
100
ns
tw(L)
Minimum Active–Low Pulse Width, Enable
(Figure 4)
3.0
4.5
5.5
4.5
3.4
3.4
µs
tw(H)
Minimum Inactive–High Pulse Width, Enable
(Figure 4)
3.0
4.5
5.5
300
150
150
ns
Minimum Pulse Width, Clock
(Figure 1)
3.0
4.5
5.5
167
125
125
ns
Maximum Input Rise and Fall Times — Data In, Clock, Enable
(Figure 1)
3.0
4.5
5.5
1
1
1
ms
tw
tr, tf
* See Thermal Considerations section.
** For a high–speed 8–Clock access, th for Enable is determined as follows:
VDD = 3 to 4.5 V, fclk > 1.78 MHz: th = 4350 – (7500/fclk)
VDD = 4.5 to 5.5 V,clk
f > 2.34 MHz: th = 3300 – (7500/fclk)
where th is in ns and fclk is in MHz.
NOTES:
1. This restriction does NOT apply for fclk rates less than those listed above. For “slow” fclk rates, use the th limits in the above table.
2. This restriction does NOT apply for an access involving more than 8 Clocks. For > 8 Clocks, use the th limits in the above table.
MC14489B
4
MOTOROLA
tf
tr
VDD
90%
CLOCK 50%
10%
VSS
tw
tw
1/fclk
tPLH
DATA OUT
tPHL
90%
50%
10%
BANK
OUTPUT
tTLH
50%
tTHL
1/fR
Figure 1.
Figure 2.
tw(L)
VALID
ENABLE
tw(H)
VDD
50%
VDD
50%
DATA IN
VSS
tsu
th
VDD
50%
CLOCK
VSS
VSS
th
tsu
trec
VDD
CLOCK
50%
FIRST
CLOCK
LAST
CLOCK
Figure 3.
VSS
Figure 4.
VDD
TEST POINT
TEST POINT
56 Ω
DEVICE
UNDER
TEST
CL *
*Includes all probe and fixture capacitance.
Figure 5.
MOTOROLA
DEVICE
UNDER
TEST
CL *
*Includes all probe and fixture capacitance.
Figure 6.
MC14489B
5
PIN DESCRIPTIONS
DIGITAL INTERFACE
Data In (Pin 12)
Serial Data Input. The bit stream begins with the MSB and
is shifted in on the low–to–high transition of Clock. When the
device is not cascaded, the bit pattern is either 1 byte (8 bits)
long to change the configuration register or 3 bytes (24 bits)
long to update the display register. For two chips cascaded,
the pattern is either 4 or 6 bytes, respectively. The display
does not change during shifting (until Enable makes a low–
to–high transition) which allows slow serial data rates, if desired.
The bit stream needs neither address nor steering bits due
to the innovative BitGrabber registers. Therefore, all bits in
the stream are available to be data for the two registers. Random access of either register is provided. That is, the registers may be accessed in any sequence. Data is retained in
the registers over a supply range of 3 to 5.5 V. Formats are
shown in Figures 8 through 14 and summarized in Table 2.
Information on the segment decoder is given in Table 1.
Data In typically switches near 50% of VDD and has a
Schmitt–triggered input buffer. These features combine to
maximize noise immunity for use in harsh environments and
bus applications. This input can be directly interfaced to
CMOS devices with outputs guaranteed to switch near rail–
to–rail. When interfacing to NMOS or TTL devices, either a
level shifter (MC14504B, MC74HCT04A) or pullup resistor of
1 kΩ to 10 kΩ must be used. Parameters to be considered
when sizing the resistor are the worst–case IOL of the driving
device, maximum tolerable power consumption, and maximum data rate.
Clock (Pin 11)
Serial Data Clock Input. Low–to–high transitions on Clock
shift bits available at Data In, while high–to–low transitions
shift bits from Data Out. The chip’s 24–1/2–stage shift register is static, allowing clock rates down to dc in a continuous or
intermittent mode. The Clock input does not need to be synchronous with the on–chip clock oscillator which drives the
multiplexing circuit.
Eight clock cycles are required to access the configuration
register, while 24 are needed for the display register when the
MC14489B is not cascaded. See Figures 8 and 9.
As shown in Figure 10, two devices may be cascaded. In
this case, 32 clock cycles access the configuration register
and 48 access the display register, as depicted in Figure 10.
Cascading of 3, 4, 5, and 6 devices is shown in Figures 11,
12, 13, and 14, respectively. Also, reference Table 2.
Clock typically switches near 50% of V DD and has a
Schmitt–triggered input buffer. Slow Clock rise and fall times
are tolerated. See the last paragraph of Data In for more information.
NOTE
To guarantee proper operation of the power–on
reset (POR) circuit, the Clock pin must NOT be
floated or toggled during power–up. That is, the
Clock pin must be stable until the V DD pin
reaches at least 3 V.
If control of the Clock pin during power–up is not
practical, then the MC14489B must be reset via bit
C0 in the C register. To accomplish this, C0 is reset low, then set high.
MC14489B
6
Enable (Pin 10)
Active–Low Enable Input. This pin allows the MC14489B to
be used on a serial bus, sharing Data In and Clock with other
peripherals. When Enable is in an inactive high state, Data
Out is forced to a known (low) state, shifting is inhibited, and
the port is held in the initialized state. To transfer data to the
device, Enable (which initially must be inactive high) is taken
low, a serial transfer is made via Data In and Clock, and
Enable is taken high. The low–to–high transition on Enable
transfers data to either the configuration or display register,
depending on the data stream length.
Every rising edge on Enable initiates a blanking interval
while data is loaded. Thus, continually loading the device with
the same data may cause the LEDs on some banks to appear
dimmer than others.
NOTE
Transitions on Enable must not be attempted
while Clock is high. This puts the device out of
synchronization with the microcontroller. Resynchronization occurs when Enable is high and
Clock is low.
This input is also Schmitt–triggered and switches near 50%
of VDD, thereby minimizing the chance of loading erroneous
data in the registers. See the last paragraph of Data In for
more information.
Data Out (Pin 18)
Serial Data Output. Data is transferred out of the shift register through Data Out on the high–to–low transition of Clock.
This output is a no connect, unless used in one of the manners discussed below.
When cascading MC14489B’s, Data Out feeds Data In of the
next device per Figures 10, 11, 12, 13, and 14.
Data Out could be fed back to an MCU/MPU to perform a
wrap–around test of serial data. This could be part of a system check conducted at power–up to test the integrity of the
system’s processor, pc board traces, solder joints, etc.
The pin could be monitored at an in–line Q.A. test during
board manufacturing.
Finally, Data Out facilitates troubleshooting a system.
DISPLAY INTERFACE
Rx (Pin 8)
External Current–Setting Resistor. A resistor tied between
this pin and ground (VSS) determines the peak segment drive
current delivered at pins a through h. Pin 8’s resistor ties into
a current mirror with an approximate current gain of 10 when
bit D23 = high (brighten). With D23 = low, the peak current is
reduced about 50%. Values for Rx range from 700 Ω to infinity. When Rx = ∞ (open circuit), the display is extinguished.
For proper current control, resistors having ± 1% tolerance
should be used. See Figure 7.
CAUTION
Small Rx values may cause the chip to overheat
if precautions are not observed. See Thermal
Considerations.
MOTOROLA
a through h (Pins 1, 2, 4 – 7, 19, 20)
Anode–Driver Current Sources. These outputs are closely–matched current sources which directly tie to the anodes
of external discrete LEDs (lamps) or display segment LEDs.
Each output is capable of sourcing up to 35 mA.
When used with lamps, outputs a, b, c, and d are used to
independently control up to 20 lamps. Output h is used to control up to 5 lamps dependently. (See Figure 17.) For lamps,
the No Decode mode is selected via the configuration register, forcing e, f, and g inactive (low).
When used with segmented displays, outputs a through g
drive segments a through g, respectively. Output h is used to
drive the decimals. Refer to Figure 9. If unused, h must be left
open.
Bank 1 through Bank 5 (Pins 9, 13, 15, 16, 17)
Diode–Bank FET Switches. These outputs are low–resistance switches to ground (VSS) capable of handling currents
of up to 320 mA each. These pins directly tie to the common
cathodes of segmented displays or the cathodes of lamps
(wired with cathodes common).
The display is refreshed at a nominal 1 kHz rate to achieve
optimum brightness from the LEDs. A 20% duty cycle is utilized.
i OH, PEAK DRIVE CURRENT (mA)
35
Special design techniques are used on–chip to accommodate the high currents with low EMI (electromagnetic interference) and minimal spiking on the power lines.
POWER SUPPLY
VSS (Pin 14)
Most–negative supply potential. This pin is usually ground.
Resistor Rx is externally tied to ground (VSS). Therefore,
the chip’s VSS pin does not contain the Rx current component.
VDD (Pin 13)
Most–positive supply potential.
To guarantee data integrity in the registers and to ensure
the serial interface is functional, this voltage may range from
3 to 6 volts with respect to VSS. For example, within this voltage range, the chip could be placed in and out of the low–
power mode.
To adequately drive the LEDs, this voltage must be 4.5 to
6 volts with respect to VSS.
The VDD pin contains the Rx current component plus the
chip’s current drain. In the low–power mode, the current mirror and clock oscillator are turned off, thus significantly reducing the VDD current, IDD.
5 V SUPPLY
BIT D23 = HIGH (BRIGHTEN LEDs)
WITH D23 = LOW, iOH IS CUT BY ∼50%.
30
25
20
15
10
5
400
800
1.2 k
1.6 k
2.0 k
2.4 k 2.8 k
3.2 k
3.6 k
4.0 k
Rx, EXTERNAL RESISTOR (Ω)
NOTE: Drive current tolerance is approximately ± 15%.
Figure 7. a through h Nominal Current per Output versus Rx
MOTOROLA
MC14489B
7
~
Table 1. Triple-Mode Segment Decoder Function Table
Lamp Conditions
Bank Nibble Value
Binary
Hexadecimal
MSB
No DecodeG)
(Invoked via
Bits C1 to C7)
7-Segment Display
Characters
LSB
Hex Decode
(Invoked via
Bits C1 to C5)
Special
Decode
(Invoked via
Bits C1 to C7)
d
c
b
$0
L
L
L
"
u
$1
L
L
H
I
c
$2
L
H
L
2
,','
on
,'I
on
I
on
$3
L
H
H
3
$4
H L
L
l./
u
on
I
L
on
$5
H L
H
s
$6
H H
L
$7
H H
H
G
,
,
$8
IH
L
L
L
8
$9
H
L
L
H
$A
H
L
H
L
9
'-I
,-,
$B
H
L
H
H
'c,
L
,L
$C
H
H
,
@
~
@
on
,-
on
u
on
on
LI
on
on
~
on
on
on
on
on
on
on
on
$0
H
H
H
c'
on
on
$E
H
H
L
E
on
on
on
$F
H
H r
H
F
on
on
on
0
on
on
"
O
O
,
,
a
on
on
on
NOTES:
1. In the No Decode mode, outputs e, f, and g are unused and are all forced inactive (low). Output
h decoding is unaffected, i.e., unchanged from the other modes. The No Decode mode is used
for three purposes:
a. Individually controlling lamps.
b. Controlling a half digit with sign.
c. Controlling annunciators. examples: AM, PM, UHF, kV, mm Hg.
2. Can be used as capital S.
3. Can be used as capital B.
4. Can be used as small g.
MC14489B
8
MOTOROLA
MOTOROLA
CLOCK
ENABLE
1
C6
2
C5
3
C4
4
C3
5
C2
6
C1
7
8
CLCOK
ENABLE
DATA IN
1
2
C0
C7
3
4
5
6
7
8
9
10
11
12
13
14
15
(a) Configuration Register Format (1 Byte)
16
17
18
19
D4
20
D3
21
D2
22
D1
23
24
L = LOW POWER MODE (BLANKS THE DISPLAY), FORCED LOW (L) BY POWER ON RESET
H = NORMAL MODE
CONTROLS BANK 1: L = HEX DECODE, H = DEPENDS ON C6
NOTE: The low–power (standby) mode places the device
CONTROLS BANK 2: L = HEX DECODE, H = DEPENDS ON C6
in a static state, thus eliminating EMI and mux switching
noise. Therefore, during precision analog measurements,
CONTROLS BANK 3: L = HEX DECODE, H = DEPENDS ON C6
the low–power mode could be invoked by a system’s MCU.
CONTROLS BANK 4: L = HEX DECODE, H = DEPENDS ON C7
Also, the low–power mode blanks the display, and could
CONTROLS BANK 5: L = HEX DECODE, H = DEPENDS ON C7
be used to flash the LEDs on and off.
L = NO DECODE, H = SPECIAL DECODE (REFER TO C1, C2, AND C3)
L = NO DECODE, H = SPECIAL DECODE (REFER TO C4 AND C5)
SEE TABLE 1
LSB
MSB
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
DATA IN
L
L
H
H
L
L
H
H
L
H
L
H
L
H
L
H
D17
BANK 5
NIBBLE
D18
D16
D15
D13
BANK 4
NIBBLE
D14
D11
D9
BANK 3
NIBBLE
D10
D8
D7
D5
SEE TABLE 1
BANK 2
NIBBLE
D6
THE LSBs OF EACH BANK NIBBLE ARE D0, D4, D8, D12, AND D16.
D12
NOTE: L = Low Voltage Level (Logic 0), H = High Voltage Level (Logic 1)
(b) Display Register Format (3 Bytes)
= ACTIVATE h IN BOTH BANKS 1 AND 2
= ACTIVATE h IN ALL BANKS
= ACTIVATE h IN BANK 1
= ACTIVATE h IN BANK 2
= ACTIVATE h IN BANK 3
= ACTIVATE h IN BANK 4
= ACTIVATE h IN BANK 5
= ALL h OUTPUTS INACTIVE
D19
L = DIM LEDs, H = BRIGHTEN LEDs
L
L
L
L
H
H
H
H
D20
BANK 1
NIBBLE
D0
D21
D23
D22
LSB
MSB
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
Figure 8. Timing Diagrams for Non–Cascaded Devices
MC14489B
9
APPLICATIONS INFORMATION
+5V
MC14489B
VDD
VSS
a
b
c
d
e
OPTIONAL
+5V
DATA OUT
f
g
Rx
h
8
8
8
8
8
8
a
•
Rx
#5
#4
#3
#2
f
e
g
d
#1
b
c
h
BANK 5
CMOS
MCU/MPU
DATA IN
CLOCK
ENABLE
BANK 4
BANK 3
BANK 2
BANK 1
Figure 9. Non–Cascaded Application Example: 5 Character Common Cathode
LED Display with Two Intensities as Controlled via Serial Port
MC14489B
10
MOTOROLA
"
~
I/)
c
~
Q)
"
.c
Q) -c
I/) .c
I/)
II)
~o~
z~z
<~<
00
~~
>..c
"''Q.°
I/) ~
.-Q)
"C.c
Q) E
>.
~
tO
~
i:;Q-
~
aJ
I
~~~
(!)U)-
I
~~Q
("I
cb ;
.c
--Gj
~
-'
<
Q
1~
Lt)
~o~
zt-z
~
~
I
In
GI
.~
>
GI
I
~
i
.!
Dl
C
=6
~
1,)
In
~
(J
~
ID
C
II:
I
w
I
~
12:
(0) I
o
C
cn
...
w
ow
.51
w
a:
~
I
c
o
~
;
ID
D
I
~
Z
~
~ I au.
~O~
:§:
~~
~-
';!?rn
I
IV
...
~
CI
;0=
C
0
(J
--
O
~
~
I/)
C
."
~
-Q)
C
.0
~
~
~
~
Q)
U)
.51
Q)
a:
>m
ii
U)
c
Q.
Q)
"C
.
I/)
.g' .~
C >
0
Q)
U "C
Q) "C
!~
~
~
'"" Q)
C .c
Q) .cQ) .-C
-I/)
OI~
C ~
.c
U
~
8
"C ~
~~
.Q I/)
u
-
8.
~~~
--~
~ffio
Sa:
~
0
01
.-C
"C
C
J,
>
u
."
-.c
-~
Q)
>.
g-.b
-"
~
I/) 0
~J
.QI
.c
Q)
>
U
"'
C
.-01
Q)
."
~
Q)
:5
.a;
.
.c
.-
.c.C
--"
I/) U
~ jg
E =>..c 01
"'
~
'""
0
:5 .5
.c .!a
1 ~li
«
z
UJ.C
..s:
UJ
Figure 10. Bit Stream Formats for Two Devices Cascaded
~
c
Q)
..:
'*
c:
Q)
(\1.0
~ c: .
~>-B.C: .2'
c.Q).c.
.~ >. Q)
"c .0 .~
Q).
u
>.~(\1
-9 B .5
.-c:-1
O ... ~W
~oaJ
O"cc(
~.
Z
2.Q)W
U) c:
c:°Q)
(\IQ)~
~
-(\I
--c:-~
°
.-~
.Il)
"§1!."C
:J
.2'
~
U)
c:
.-(\I
&JI
.
'E~U)
o>-Q)
U(\1>.
Q)Q..O
>.
.~
~
C')
"ccn
Q)
(\I
.c.-
Q) -~
.=
01 2.
-c:U)
C::QC:
Q) (\I
e
Q)"C.c.c.~
-:J-.r
Q)
0Ic:~
.
c:
.c:
U
:J.C.Q)
"c~C.
U)
1/1
..
Q)
...
1/1
.51
Q)
11:
c
.2
~
..
~
C)
;;:
c
O
u
~
~
~-~
OQ)J:
->~
J, "'
~
>
(\I :;:
E
Q)
UQ)Q)
(\I .-U)
-<{
c.
.c:
~Q) U).CJ.-
In
...
41
"cn
'61
41
a:
>la
"5.
In
c
Q).C.
.~ .!J Q)
~»
.c:
Q) .-
:§:
.5
OI"cU
.-"c
(\I
.c:
Q) .5
U~-1
~UJ
~"c
(\I (\I [D
U ~
Q)Q)w
.O=Q)
-c:0)
~ .-3
E ~ c.
B
>-:J~
-HC')
~o-:
...~
C: Q)
.-->.
.c.0).o
U
.-(\I
.c.
~
U)
Q)
c:
co
"'
-~
~Q)2.
~
UJ
>.
0)
-1-9C:
aJoe
c(.-:::.
z~C\I
WO~
"I:i.b~
Q)
-
"Cc:Q)
.2U
(\I
~
.->
c:Q)U
.-.c:
~
...
(\IQ)-1
~UJ
U).r:aJ
Q) .2'
c(
(\I
>..c:Z
.O~W
,
U
Q)
~~~
B-s .c.~
...01.C::J~
O
O
"C
~
,
.0
..
~
~
OIU)O
c: .-=
.-"
.O
"C~(\I-1U)
Q)aJ(\1
-a;c("C
.c:ZQ)
-Wc:c:C:
Q) Q)
.c:.c:E
~~~
Uj
Figure 11. Bit Stream Formats for Three Devices Cascaded
b
z
(\I
.-
~
~~
~o
"'
:.:=0:.:
Z I-
Z
<
<
00
00
Lt)
:11:
I~
m
0>
~
v
v
.u
~
.c
~
"'
~
UJI
c:
Q) "'
.c: Q)
$:'(iJc:
8
-'
0
"'
Q)
~
'"'
'(iJ;
C:.c:
~
~>- .-c:
~z
<n
~
-Q)
I/)
~>.-.Q
"0Q)
"'
~o~
ZI-Z
~
~
;b~
.-:3
'"' c
0
Q)
'"'.C:
Q)'(iJ C
C 0
~ CI
-C
C .-
M
=11=
ID
I~
0)
~
~
~
,U
<
~~i
'"'
z
t-
Q)
>
~
CI
<
00
<
00
C
~o
N
*
U
In
ffi
-'
~
"I
~
qo
,..
U
~
.c
~
...
:g
w
m
0>
(/)
Qj
-u;
'61
0)
~
c
o
;
cu
..
~
Dl
-=
C
0
U
In
Q)
u
">
Q)
0
i
~~
"'
~o~
z
0"0
.-C
-Q)
~ a.
:. Q)
CI"0 IC
C U>
§
u
~
.c
~
"'
0
>-'"'
~~
~o
~
0
-IU
1~
IU
(,)
--
§:
--
0
8 .~
Q) >
III
.."0
Q)
-.-"0
~
CI
Q)
~
~>-
~
Q)
Q) B
.= I/)
-~
~ u
>Q)Q)
ca
£:5
-c:
c.
CI ..!
c
.E ~
:.:3
u
"-'
~8
0'"'
"0 u
1~
>
~
U
~
~
<.>
c:
~
'"'
-
-Q)
a.>.
~z
<1"
~;b
:c-'"'
ClO
"'
~o~
2
1-
<
00
:c~
Q)
~>
U
"'
.E
Q)
.Q
-.c:
U>
:.
~~
00
2
<
00
~
.c
9
"'
0)
~
"'"
I ~~
~,
W
"'"
~
U
~
8
;1
.~
'"'
Q)
£
.a;
.
.-CI
E.C:~
>-u
=
~
.~
.Q
,..
c: .c:
.-CI
.c:
~
U
0
:c.c
~
~.-
~z
~0
lili
OLL
I
gJ.!..
~0",
<n
::J
a.
o~
~::J
uu
~fi3
W~
mt;:
~cn
I-cn:c
~
I
~0:..
5~~
I
-->
8Z
LL(!)W
~
z
wo
0:
I/)
~
1="
~~
Z
~o~
Z
I-
~ ~
.c
~
...
ID
=!I:
;;:aJ
~a(t;
8 wc
10
-11:
!
I~
ID
0)
CO
~
~
~
()
~
~ ~ ~
1
~5
~o
"'
z
au.
~a-
'
~
<
u
1Z
~
~
§
u
c
w ~
~.;
~z
<n
z
~a:-
~I:;
~o~
ZI-Z
~
~
.c
~
"'
::I1:!~
(!)00-->
LL(!)W
~o
M
'#:
UJ
-'
00
m
01
~
qq~
U
~
~
III
~!;
~o
"'
~
<
CD
('II
=11:
w
-'
[0
<
z
w
m
0)
~
~
~
?-
a:
5
1Z
--'
<
zO
8
I ~ 11.
~
~~~
IIJ 115!7j~
~ I~~~
~
III
IV
U
IV
~
w
Ir
~
I
CI.
O
~
~
~
8
-'
(.)
~
UI
...
Q)
~
'51
Q)
a:
c
o
;:
la
...
~
CI
;;:
C
O
(J
~z
<a
8
z
Ou.
~5
~o
"'
~o~
ZLZ
<~<
CD
.c
~
m
CD
,..
:11:
~
z
w
q-
~
c:;
~
8
5
..
w
a:
<
(.)
1Z
~
0
.2
~
:.:. u
-0
~
CJ
>u
~
I
=>
Inll.
o~
~=>
l>~
cn:l:
>=~
I
aJtL:
f-~cn
...
Q!
:5
.a;
.
.-CJ
~ID
Z<
wffi
Ou.
g~~
~
(.!)cn-
~~
.-,..
:2"...
CJO
:2~
W ,..
> (1J
-::
I~ I~
w
F;°~
~~
C
~
Q!
~.c
.2 :E
-CJ
.c
:.
u
0
.c.c
~ (/)
~.-
~
~
~
z
8
~~
"1
0
0...
E.C ~
>.u
=
as
8
.<
~
CI~~
GI
c
~
a:
W
>Q!~
ca
.c--c
c.
CJ .-
U
(1J
.E
w
.c
-.c
"'
:.
Sa:
I -J
w
m
0)
rD
~
cn
..I
GI(OW
-,..-0
~
Q!
c.>.
~
-0."
'<
a:a:w
::J~U
<.?CI)-->
u.<.?w
Zwc
CJ
.-0
8 .~
w Q!
~-0-0
1.;
>
-::
U
(1J
w
Ir
<
u
C
0
"§
~
:.
W
CJ-0
10=
.
C
(/)
e:
1-
u
.c
~
...
~
-C
C
0
.-C
~
w
UI
Q)
U
'>
Q)
C
><
in
Dl
C
=6
:.
Q!
c
Win
C
~
1-
<
~
zgz
<
CD
,..
...c
0
w
'<~
0
c
.(/)
l~
8~o
8
d
as
Q!
.~~
-0Q! 0
~~'"'
II)
c
~
.p!.;.
(/)
C.c
as
;.
>.
as
-w
~
b
z
[!:a[;j
1
~wc
Olr
(,)
Figure 14. Bit Stream Formats tor Six Devices Cascaded
15
Table 2. Register Access for Two or More Cascaded Devices
Configuration Register Access
Display Register Access
Total Number of Bytes
Number of Leading
“Don’t Care” Bytes
Total Number of Bytes
Number of Leading
“Don’t Care” Bytes
3N
2
3N + 2
2
If 3N – 1 is a Multiple of 4
3N – 1
1
3N + 1
1
If 3N – 2 is a Multiple of 4
3N – 2
0
3N
0
If 3N – 3 is a Multiple of 4
3N – 2
0
3N
0
Ci i *
Criteria*
If 3N is a Multiple of 4
* N = number of devices that are cascaded. For example, to drive 10 digits, 2 devices are cascaded; therefore, N = 2. To drive 35 digits, seven
devices are cascaded; therefore N = 7.
LED DISPLAY
+5V
8
5
+5V
VDD
CMOS
MCU/MPU
R1
MC14489B
Rx
R2
VSS
NOTE: R1 limits the maximum current to avoid damaging the display and/or the MC14489B
due to overheating. See the Thermal Considerations section. An 1/8 watt resistor
may be used for R1. R2 is a 1 kΩ or 5 kΩ potentiometer (≥ 1/8 watt). R2 may be a
light–sensitive resistor.
Figure 15. Common–Cathode LED Display with Dial–Adjusted Brightness
MC14489B
16
MOTOROLA
UNIVERSAL OVERFLOW
(“1” OR “HALF–DIGIT”)
5–DIGIT DISPLAY
7
USE TO DRIVE LAMP
OR MINUS SIGN
h
1
2 3
4
5
BANK OUTPUTS
a TO g
MC14489B
3
INPUT LINES
NOTE: A Universal Overflow pins out all anodes and cathodes.
Figure 16. Driving 5 1/2 Digits
MOTOROLA
MC14489B
17
THESE LAMPS
INDEPENDENTLY
CONTROLLED WITH
BITS D0 TO D19
a
b
MC14489B
c
d
e
NC
f
NC
g
NC
h
BANK 1
BANK 2
THESE LAMPS DEPENDENTLY
CONTROLLED WITH
BITS D20, D21, AND D22*
BANK 3
BANK 4
BANK 5
3
CMOS
MCU/MPU
* If required, this group of lamps can be independently controlled. To accomplish independent control, only connect lamps to BANK 1 and
BANK 2 for output h (two lamps). Then, use bits D20, D21, and D22 for control of these two lamps.
Figure 17. 25–Lamp Application
MC14489B
18
MOTOROLA
4
•
4
4
4
a TO d
e TO h
BANK 1
TO
BANK 4
BANK 5
MC14489B
3
CMOS MCU/MPU
Figure 18. 4–Digit Display Plus Decimals with Four Annunciators
or 4–1/2–Digit Display Plus Sign
MUXED 5–DIGIT MONOLITHIC DISPLAY (CLUSTER)
HEWLETT–PACKARD 5082–7415 OR EQUIVALENT
8
14
12
3
6
2
10
8
5
1
13
4
9
7
7
6
5
4
2
1
20
19
17
16
15
13
9
MC14489B
3
INPUT LINES
Figure 19. Compact Display System with Three Components
MOTOROLA
MC14489B
19
THERMAL CONSIDERATIONS
The MC14489B is designed to operate with a chip–junction
temperature (TJ) ranging from – 40 to 130°C, as indicated in
the electrical characteristics tables. The ambient operating
temperature range (TA) is dependent on RθJA, the internal
chip current, how many anode drivers are used, the number
of bank drivers used, the drive current, and how the package
is cooled. The maximum ratings table gives the thermal resistance, junction–to–ambient, of the MC14489B mounted on a
pc board using natural convection to be 90°C per watt for the
plastic DIP. The SOG thermal resistance is 100°C per watt.
The following general equation (1) is used to determine the
power dissipated by the MC14489B.
PT = PD + PI
(1)
where
PT = Total power dissipation of the MC14489B
PD = Power dissipated in the driver circuitry (mW)
PI = Power dissipated by the internal chip
circuitry (mW)
That is, if TA = 79°C, the maximum junction temperature is
130°C. The chip’s average temperature for this example is
lower than 130°C because all segments are usually not illuminated simultaneously for an indefinite period.
Worst–Case Analysis Example 2:
16 lamps (4 banks and 4 anode drivers)
SOG without heat sink on PC board
iOH = 30 mA max
VLED = 1.8 V min
VDD = 5.5 max
PD = (30)(4)(5.5 – 1.8)(4/5) = 355 mW
Ref. (2)
PI = (1.5)(5.5) + 3[5.5 – 3(1.0)] = 16 mW
Ref. (3)
Therefore, PT = 355 + 16 = 371 mW
Ref. (1)
and ∆Tchip = RθJAPT = (100°C/W)(0.371) = 37°C
The equations for the two terms of the general equation
are:
PD = (iOH) (N)(VDD – VLED)(B/5)
(2)
PI = (1.5 mA)(VDD) + IRx(VDD – IRxRx)
(3)
where
iOH = Peak anode driver current (mA)
IRx = iOH /10, with iOH = the peak anode driver current
(mA) when the dimmer bit is high
N = Number of anode drivers used
B = Number of bank drivers used
Rx = External resistor value (kΩ)
VDD = Maximum supply voltage, referenced to VSS
(volts)
VLED = Minimum anticipated voltage drop across the
LED
1.5 mA = Operating supply current of the MC14489B
The following two examples show how to calculate the
maximum allowable ambient temperature.
Finally, the maximum allowable
TA = TJmax – ∆Tchip = 130 – 37 = 93°C
To extend the allowable ambient temperature range or to
reduce TJ, which extends chip life, a heat sink such as shown
in Figure 20 can be used in high–current applications. Alternatively, heat–spreader techniques can be used on the PC
board, such as running a wide trace under the MC14489B and
using thermal paste. Wide, radial traces from the MC14489B
leads also act as heat spreaders.
AAVID #5804 or equivalent
(Tel. 603/524–4443, FAX 603/528–1478)
Motorola cannot recommend one supplier over another and
in no way suggests that this is the only heat sink supplier.
Worst–Case Analysis Example 1:
Figure 20. Heat Sink
5–digit display with decimals (5 banks and 8 anode drivers)
DIP without heat sink on PC board
iOH = 20 mA max
VLED = 1.8 V min
VDD = 5.25 max
Table 3. LED Lamp and Common–Cathode Display
Manufacturers
Supplier
PD = (20)(8)(5.25 – 1.8)(5/5) = 552 mW
Ref. (2)
QT Optoelectronics
PI = (1.5)(5.25) + 2[5.25 – 2(2)] = 10 mW
Ref. (3)
Hewlett–Packard (HP), Components Group
Therefore, PT = 552 + 10 = 562 mW
Ref. (1)
Industrial Electronic Engineers (IEE), Component Products Div.
and ∆Tchip = RθJAPT = (90°C/W)(0.562) = 51°C
Finally, the maximum allowable
TA = TJmax – ∆Tchip = 130 – 51 = 79°C
MC14489B
20
Purdy Electronics Corp., AND Product Line
NOTE: Motorola cannot recommend one supplier over another
and in no way suggests that this is a complete listing of
LED suppliers.
MOTOROLA
PACKAGE DIMENSIONS
P SUFFIX
PLASTIC DIP
CASE 738–03
-A20
11
1
10
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD
FLASH.
B
C
-T-
L
DIM
A
B
C
D
E
F
G
J
K
L
M
N
K
SEATING
PLANE
M
E
G
N
F
J 20 PL
0.25 (0.010)
D 20 PL
0.25 (0.010)
M
T A
M
T B
M
M
INCHES
MIN
MAX
1.010 1.070
0.240 0.260
0.150 0.180
0.015 0.022
0.050 BSC
0.050 0.070
0.100 BSC
0.008 0.015
0.110 0.140
0.300 BSC
15°
0°
0.020 0.040
MILLIMETERS
MIN
MAX
25.66 27.17
6.10
6.60
3.81
4.57
0.39
0.55
1.27 BSC
1.27
1.77
2.54 BSC
0.21
0.38
2.80
3.55
7.62 BSC
0°
15°
1.01
0.51
DW SUFFIX
SOG PACKAGE
CASE 751D–04
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.150
(0.006) PER SIDE.
5. DIMENSION D DOES NOT INCLUDE
DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.13
(0.005) TOTAL IN EXCESS OF D DIMENSION
AT MAXIMUM MATERIAL CONDITION.
–A–
20
11
–B–
10X
P
0.010 (0.25)
1
M
B
M
10
20X
D
0.010 (0.25)
M
T A
B
S
J
S
F
R
C
–T–
18X
MOTOROLA
G
K
SEATING
PLANE
X 45 _
DIM
A
B
C
D
F
G
J
K
M
P
R
MILLIMETERS
MIN
MAX
12.65
12.95
7.40
7.60
2.35
2.65
0.35
0.49
0.50
0.90
1.27 BSC
0.25
0.32
0.10
0.25
0_
7_
10.05
10.55
0.25
0.75
INCHES
MIN
MAX
0.499
0.510
0.292
0.299
0.093
0.104
0.014
0.019
0.020
0.035
0.050 BSC
0.010
0.012
0.004
0.009
0_
7_
0.395
0.415
0.010
0.029
M
MC14489B
21
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
Mfax is a trademark of Motorola, Inc.
How to reach us:
USA / EUROPE / Locations Not Listed: Motorola Literature Distribution;
P.O. Box 5405, Denver, Colorado 80217. 1–303–675–2140 or 1–800–441–2447
JAPAN: Nippon Motorola Ltd.; SPD, Strategic Planning Office, 141,
4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan. 81–3–5487–8488
Customer Focus Center: 1–800–521–6274
Mfax: [email protected] – TOUCHTONE 1–602–244–6609
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbor Center,
Motorola Fax Back System
– US & Canada ONLY 1–800–774–1848 2 Dai King Street, Tai Po, N.T., Hong Kong. fax: 852–26666123
– http://sps.motorola.com/mfax/
HOME PAGE: http://mot-sps.com/
MC14489
22
A
MC14489B