H11AA1 Vishay Semiconductors Optocoupler, Phototransistor Output, AC Input, with Base Connection FEATURES • AC or polarity insensitive input • Built-in reverse polarity input protection 1 6 B C/A 2 5 C NC 4 E A/C 3 • I/O compatible with integrated circuits • Industry standard DIP package • Isolation test voltage: 5300 VRMS • Lead (Pb)-free component • Component in accordance to RoHS 2002/95/EC and WEEE 2002/96/EC i179010 APPLICATIONS • Telephone line detection • AC line motor • PLC DESCRIPTION • Instrumentation The H11AA1 is a bi-directional input optically coupled isolator consisting of two inverse parallel gallium arsenide infrared LEDs coupled to a silicon NPN phototransistor in a 6 pin DIP package. The H11AA1 has a minimum CTR of 20 %, a CTR symmetry of 1:3 and is designed for applications requiring detection or monitoring of AC signals. AGENCY APPROVALS • UL1577, file no. E52744 system code H or J, double protection • CSA 93751 • BSI IEC 60950; IEC 60065 • DIN EN 60747-5-5 available with option 1 • FIMKO ORDER INFORMATION PART REMARKS H11AA1 CTR > 20 %, DIP-6 H11AA1-X006 CTR > 20 %, DIP-6 400 mil (option 6) H11AA1-X007 CTR > 20 %, SMD-6 (option 7) H11AA1-X009 CTR > 20 %, SMD-6 (option 9) Note For additional information on the available options refer to option information. ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT INPUT Forward continuous current Power dissipation IF 60 mA Pdiss 100 mW 1.3 mW/°C Derate linearly from 25 °C OUTPUT Power dissipation Pdiss Derate linearly from 25 °C Collector emitter breakdown voltage BVCEO 200 mW 2.6 mW/°C 30 V Emitter base breakdown voltage BVEBO 5 V Collector base breakdown voltage BVCBO 70 V Document Number: 83608 Rev. 1.6, 08-May-08 For technical questions, contact: [email protected] www.vishay.com 277 H11AA1 Vishay Semiconductors Optocoupler, Phototransistor Output, AC Input, with Base Connection ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT between emitter and detector, referred to standard climate 23 °C/50% RH, DIN 50014 VISO 5300 VRMS Creepage distance ≥7 mm Clearance distance ≥7 mm COUPLER Isolation test voltage (RMS) Comparative tracking index per DIN IEC 112/VDE 0303, part 1 CTI 175 VIO = 500 V, Tamb = 25 °C RIO ≥ 1012 VIO = 500 V, Tamb = 100 °C RIO ≥ 1011 Ω Storage temperature range Tstg - 55 to + 150 °C Operating temperature range Tamb - 55 to + 100 °C Lead soldering time at 260 °C Tsld 10 s Isolation resistance Ω Note Tamb = 25 °C, unless otherwise specified. Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. ELECTRICAL CHARACTERISTCS PARAMETER TEST CONDITION SYMBOL IF = 10 mA VF MIN. TYP. MAX. UNIT 1.2 1.5 V INPUT Forward voltage OUTPUT IC = 1 mA BVCEO 30 V Emitter base breakdown voltage Collector emitter breakdown voltage IE = 100 µA BVEBO 5 V Collector base breakdown voltage IC = 100 µA BVCBO 70 Collector emitter leakage current VCE = 10 V ICEO IF = 10 mA, IC = 0.5 mA VCEsat V 5 100 nA 0.4 V COUPLER Collector emitter saturation voltage Note Tamb = 25 °C, unless otherwise specified. Minimum and maximum values were tested requierements. Typical values are characteristics of the device and are the result of engineering evaluations. Typical values are for information only and are not part of the testing requirements. CURRENT TRANSFER RATIO PARAMETER DC current transfer ratio Symmetry (CTR at + 10 mA)/(CTR at - 10 mA) www.vishay.com 278 TEST CONDITION SYMBOL MIN. IF = 10 mA, VCE = 10 V CTRDC 20 0.33 For technical questions, contact: [email protected] TYP. MAX. UNIT % 1 3 Document Number: 83608 Rev. 1.6, 08-May-08 H11AA1 Optocoupler, Phototransistor Output, AC Input, with Base Connection Vishay Semiconductors TYPICAL CHARACTERISTICS Tamb = 25 °C, unless otherwise specified 1.5 Normalized to: VCE = 10 V, IF = 10 mA TA = 70 °C CTRce(sat) VCE = 0.4 V 40 NCTR - Normalized IF - LED Forward Current (mA) 60 85 °C 20 25 °C 0 - 55 °C - 20 1.0 0.5 NCTR(SAT) - 40 NCTR - 60 - 1.5 - 1.0 - 0.5 0.0 0.5 1.0 1.5 VF - LED Forward Voltage (V) ih11aa1_01 0.0 0.1 Fig. 1 - LED Forward Current vs.Forward Voltage 100 1.5 Normalized to: VCE = 10 V, IF = 10 mA TA = 85 °C CTRce(sat) VCE = 0.4 V VCE = 10 V, IF = 10 mA TA = 25 °C 1.0 CTRce(sat) VCE = 0.4 V 0.5 NCTR(SAT) NCTR 0.0 0.1 ih11aa1_02 1 10 NCTR - Normalized CTR Normalized to: 100 IF - LED Current (mA) 1.0 0.5 NCTR(SAT) NCTR 0.0 0.1 1 Fig. 2 - Normalized Non-Saturated and Saturated CTR vs. LED Current 10 100 IF - LED Current (mA) ih11aa1_05 Fig. 5 - Normalized Non-Saturated and Saturated CTR vs. LED Current 35 1.5 Normalized to: VCE = 10 V, IF = 10 mA TA = 50 °C CTRce(sat) VCE = 0.4 V 1.0 0.5 NCTR(SAT) NCTR 0.0 ICE - Collector Current (mA) NCTR - Normalized CTR 10 Fig. 4 - Normalized Non-Saturated and Saturated CTR vs. LED Current 1.5 NCTR - Normalized CTR 1 IF - LED Current (mA) ih11aa1_04 30 25 50 °C 20 70 °C 25 °C 15 100 °C 10 5 0 0.1 ih11aa1_03 1 10 100 IF - LED Current (mA) Fig. 3 - Normalized Non-Saturated and Saturated CTR vs. LED Current Document Number: 83608 Rev. 1.6, 08-May-08 0 ih11aa1_06 10 20 30 40 50 60 IF - LED Current (mA) Fig. 6 - Collector Emitter Current vs. Temperature and LED Current For technical questions, contact: [email protected] www.vishay.com 279 H11AA1 Vishay Semiconductors Optocoupler, Phototransistor Output, AC Input, with Base Connection ICEO - Collector Emitter (nA) 105 10 103 102 VCE = 10 V 101 TYPICAL 100 10-1 10-2 - 20 0 20 40 60 80 IF = 10 mA 1 0.1 Fig. 7 - Collector Emitter Leakage Current vs. Temperature 10 100 Fig. 10 - Normalized Photocurrent vs. LED Current 2.0 70 °C Normalized to: IF = 10 mA 50 °C NhFE(sat) - Normalized Saturated hFE NCTRcb - Normalized CTRcb 1 IF - LED Current (mA) ih11aa1_10 1.5 VCB = 9.3 V 1.0 0.5 25 °C 50 °C 70 °C 1.5 25 °C Normalized to: Ib = 20 µA VCE = 10 V 1.0 VCE = 0.4 V 0.5 0.0 0.0 0.1 1 10 1 100 10 ih11aa1_11 IF - LED Current (mA) ih11aa1_08 Fig. 8 - Normalized CTRcb vs. LED Current and Temperature 100 1000 Ib - Base Current (µA) Fig. 11 - Normalized Saturated hFE vs. Base Current and Temperature 1.5 1000 100 ICB = 1.0357 x IF ^ 1.3631 NhFE(sat) Normalized Saturated hFE Icb - Collector Base Photocurrent (µA) NIB - Ta = - 20 °C NIb, Ta = 25 °C NIb, Ta = 50 °C NIb, Ta = 70 °C 0.01 0.1 100 Tamb - Ambient Temperature (°C) ih11aa1_07 Normalized to: Normalized Photocurrent 104 10 1 0.1 70 °C 50 °C 1.0 Normalized to: VCE = 10 V IB = 20 µA - 25 °C - 20 °C 0.5 VCE = 0.4 V 0.0 0.01 0.1 ih11aa1_09 1 10 100 IF - LED Current (mA) Fig. 9 - Collector Base Photocurrent vs. LED Current www.vishay.com 280 1 ih11aa1_12 10 100 1000 Ib - Base Current (µA) Fig. 12 - Normalized Saturated hFE vs. Base Current and Temperature For technical questions, contact: [email protected] Document Number: 83608 Rev. 1.6, 08-May-08 H11AA1 Optocoupler, Phototransistor Output, AC Input, with Base Connection 2.5 IF = 10 mA VCC = 5 V, VTH = 1.5 V tPHL 100 2.0 1.5 10 tPLH 1.0 100 1 0.1 ih11aa1_13 1 tpHL - Propagation Delay (µs) tp - Propagation Delay (µs) 1000 Vishay Semiconductors 10 RL - Collector Load Resistor (kΩ) Fig. 13 - Propagation Delay vs. Collector Load Resistor IF tD tR VO tPLH VTH = 1.5 V tF tS tPHL ih11aa1_14 Fig. 14 - Switching Waveform VCC = 5 V F = 10 kHz, DF = 50 % RL VO IF = 10 mA ih11aa1_15 Fig. 15 - Switching Schematic Document Number: 83608 Rev. 1.6, 08-May-08 For technical questions, contact: [email protected] www.vishay.com 281 H11AA1 Vishay Semiconductors Optocoupler, Phototransistor Output, AC Input, with Base Connection PACKAGE DIMENSIONS in inches (millimeters) 3 2 1 4 5 6 Pin one ID 0.248 (6.30) 0.256 (6.50) ISO method A 0.335 (8.50) 0.343 (8.70) 0.048 0.039 (1.00) min. 0.300 (7.62) (0.45) typ. 0.022 (0.55) 0.130 (3.30) 0.150 (3.81) 18° 4° typ. 0.114 (2.90) 0.031 (0.80) min. 0.031 (0.80) 0.018 (0.45) 0.035 (0.90) 0.022 (0.55) 0.100 (2.54) typ. 0.130 (3.0) 0.010 (0.25) typ. 3° to 9° 0.300 to 0.347 (7.62 to 8.81) i178004 Option 6 Option 7 Option 9 0.407 (10.36) 0.391 (9.96) 0.307 (7.8) 0.291 (7.4) 0.300 (7.62) typ. 0.375 (9.53) 0.395 (10.03 ) 0.300 (7.62) ref. 0.028 (0.7) 0.180 (4.6) 0.160 (4.1) 0.315 (8.0) min. 0.014 (0.35) 0.010 (0.25) 0.400 (10.16) 0.430 (10.92) www.vishay.com 282 0.331 (8.4) min. 0.406 (10.3) max. 0.0040 (0.102) 0.0098 (0.249) 0.012 (0.30 ) typ. 0.020 (0.51 ) 0.040 (1.02 ) 15° max. 0.315 (8.00) min. For technical questions, contact: [email protected] 18450 Document Number: 83608 Rev. 1.6, 08-May-08 H11AA1 Optocoupler, Phototransistor Output, AC Input, with Base Connection Vishay Semiconductors OZONE DEPLETING SUBSTANCES POLICY STATEMENT It is the policy of Vishay Semiconductor GmbH to 1. Meet all present and future national and international statutory requirements. 2. Regularly and continuously improve the performance of our products, processes, distribution and operating systems with respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment. It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone depleting substances (ODSs). The Montreal Protocol (1987) and its London Amendments (1990) intend to severely restrict the use of ODSs and forbid their use within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances. Vishay Semiconductor GmbH has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in the following documents. 1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively. 2. Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental Protection Agency (EPA) in the USA 3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C (transitional substances) respectively. Vishay Semiconductor GmbH can certify that our semiconductors are not manufactured with ozone depleting substances and do not contain such substances. We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications. All operating parameters must be validated for each customer application by the customer. Should the buyer use Vishay Semiconductors products for any unintended or unauthorized application, the buyer shall indemnify Vishay Semiconductors against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use. Vishay Semiconductor GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany Document Number: 83608 Rev. 1.6, 08-May-08 For technical questions, contact: [email protected] www.vishay.com 283 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1