ILD610 Vishay Semiconductors Optocoupler, Phototransistor Output, Dual Channel FEATURES • Dual version of SFH610 series A 1 8 E • Isolation test voltage, 5300 VRMS C 2 7 C • VCEsat 0.25 (≤ 0.4) V at IF = 10 mA, IC = 2.5 mA A 3 6 E • VCEO = 70 V C 4 5 C • Lead (Pb)-free component • Component in accordance to 2002/95/EC and WEEE 2002/96/EC i179045 RoHS AGENCY APPROVALS DESCRIPTION • UL1577, file no. E52744 system code H or J, double protection The ILD610 series is a dual channel optocoupler series for high density applications. Each channel consists of an optically coupled pair with a gallium arsenide infrared LED and silicon NPN phototransistor. Signal information, including a DC level, can be transmitted by the device while maintaining a high degree of electrical isolation between input and output. The ILD610 series is the dual version of SFH610 series and uses a repetitive pin-out configuration instead of the more common alternating pin-out used in most dual couplers. • DIN EN 60747-5-2 (VDE 0884)/DIN EN 60747-5-5 pending available with option 1 • CSA 93751 • BSI IEC 60950 IEC 60065 ORDER INFORMATION PART REMARKS ILD610-1 CTR 40 to 80 %, DIP-8 ILD610-2 CTR 63 to 125 %, DIP-8 ILD610-3 CTR 100 to 200 %, DIP-8 ILD610-4 CTR 160 to 320 %, DIP-8 ILD610-2X007 CTR 63 to 125 %, SMD-8 (option 7) ILD610-3X006 CTR 100 to 200 %, DIP-8 400 mil (option 6) ILD610-3X009 CTR 100 to 200 %, SMD-8 (option 9) ILD610-4X009 CTR 160 to 320 %, SMD-8 (option 9) Note For additional information on the available options refer to option information. ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT t ≤ 1.0 ms VR IFSM Pdiss 6.0 1.5 100 1.3 60 V A mW mW/°C mA 70 50 100 150 2.0 V mA mA mW mW/°C INPUT Reverse voltage Surge forward current Power dissipation Derate linearly from 25 °C Forward continuous current OUTPUT Collector emitter voltage Collector current Power dissipation Derate linearly from 25 °C Document Number: 83651 Rev. 1.8, 09-Jan-08 IF t ≤ 1.0 ms VCE IC IC Pdiss For technical questions, contact: [email protected] www.vishay.com 1 ILD610 Optocoupler, Phototransistor Output, Dual Channel Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Isolation test voltage t = 1.0 s Isolation resistance VIO = 500 V, Tamb = 25 °C VIO = 500 V, Tamb = 100 °C VISO 5300 VRMS Storage temperature RIO RIO Tstg ≥ 1012 ≥ 1011 - 55 to + 150 Ω Ω °C Operating temperature Tamb - 55 to + 100 °C Tj 100 °C 10 s COUPLER Junction temperature Lead soldering time at 260 °C Note Tamb = 25 °C, unless otherwise specified. Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. ELECTRICAL CHARACTERISTICS PARAMETER TEST CONDITION PART SYMBOL MIN. TYP. MAX. UNIT INPUT Forward voltage IF = 60 mA VF 1.25 1.65 V Reverse current VR = 6.0 V IR 0.01 10 µA VR = 0 V, f = 1.0 MHz CO 25 pF V Capacitance OUTPUT Collector emitter breakdown voltage IC = 10 mA, IE = 10 µA Collector emitter dark current VCE = 10 V Collector emitter capacitance VCE = 5.0 V, f = 1.0 MHz VCE = 10 V Collector emitter leakage current BVCEO 70 90 BVCEO 6.0 7.0 ICEO 2.0 V 50 nA 50 nA CCE 7.0 ILD610-1 ICEO 2.0 pF ILD610-2 ICEO 2.0 50 nA ILD610-3 ICEO 5.0 100 nA ILD610-4 ICEO 5.0 100 nA VCEsat 0.25 0.40 V CC 0.35 COUPLER Collector emitter saturation voltage IF = 10 mA, IC = 2.5 mA Coupling capacitance pF Note Tamb = 25 °C, unless otherwise specified. Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements. CURRENT TRANSFER RATIO PARAMETER TEST CONDITION IF = 10 mA, VCE = 5.0 V CTR (1) IF = 1.0 mA, VCE = 5.0 V PART SYMBOL MIN. ILD610-1 CTR 40 TYP. MAX. 80 UNIT % ILD610-2 CTR 63 125 % ILD610-3 CTR 100 200 % ILD610-4 CTR 160 320 ILD610-1 CTR 13 % ILD610-2 CTR 22 % ILD610-3 CTR 34 % ILD610-4 CTR 56 % % Note (1) CTR will match within a ratio of 1.7:1 www.vishay.com 2 For technical questions, contact: [email protected] Document Number: 83651 Rev. 1.8, 09-Jan-08 ILD610 Optocoupler, Phototransistor Output, Dual Channel Vishay Semiconductors SWITCHING CHARACTERISTICS PARAMETER TEST CONDITION PART SYMBOL MIN. TYP. MAX. UNIT NON-SATURATED ILD610-1 Rise time Fall time Turn-on time Turn-off time VCC = 5.0 V, RL = 75 Ω, IF = 10 mA VCC = 5.0 V, RL = 75 Ω, IF = 10 mA VCC = 5.0 V, RL = 75 Ω, IF = 10 mA VCC = 5.0 V, RL = 75 Ω, IF = 10 mA ILD610-2 ILD610-3 2.0 tr 2.5 2.9 ILD610-4 3.3 ILD610-1 2.0 ILD610-2 ILD610-3 tf 2.6 3.1 ILD610-4 3.5 ILD610-1 3.0 ILD610-2 ILD610-3 ton 3.2 3.6 ILD610-4 2.3 ILD610-1 2.9 ILD610-2 ILD610-3 toff 3.4 3.7 ILD610-4 4.1 ILD610-1 2.0 µs µs µs µs SATURATED Rise time VCC = 5.0 V, RL = 1.0 kΩ, IF = 5.0 mA ILD610-2 ILD610-3 tr ILD610-4 Fall time Turn-on time VCC = 5.0 V, RL = 1.0 kΩ, IF = 5.0 mA VCC = 5.0 V, RL = 1.0 kΩ, IF = 5.0 mA Turn-off time 11 ILD610-2 2.6 ILD610-3 tf 3.1 ILD610-4 15 ILD610-1 3.0 ILD610-2 ILD610-3 ton 4.3 4.6 µs µs 6.0 ILD610-1 18 ILD610-2 2.9 ILD610-3 µs 4.6 toff ILD610-4 Document Number: 83651 Rev. 1.8, 09-Jan-08 3.3 ILD610-1 ILD610-4 VCC = 5.0 V, RL = 1.0 kΩ, IF = 5.0 mA 2.8 For technical questions, contact: [email protected] 3.4 µs 25 www.vishay.com 3 ILD610 Optocoupler, Phototransistor Output, Dual Channel Vishay Semiconductors TYPICAL CHARACTERISTICS Tamb = 25 °C, unless otherwise specified 1.4 1.5 Tamb = - 55 °C 1.2 Tamb = 25 °C 1.1 1.0 0.9 Normalized to: VCE = 10 V, I F = 10 mA Tamb = 25 °C NCTR - Normalized CTR VF - Forward Voltage (V) 1.3 Tamb = 85 °C 1.0 CTRCE(sat) VCE = 0.4 V Tamb= 70 °C 0.5 NCTR(SAT) NCTR 0.8 0.0 0.7 0.1 1 10 IF - Forward Current (mA) 100 1 10 100 iilct6_04 Fig. 1 - Forward Voltage vs. Forward Current 1.5 Fig. 4 - Normalized Non-Saturated and Saturated CTR vs. LED Current 1.5 Normalized to: VCE = 10 V, I F = 10 mA Tamb = 25 °C CTRCE(sat) VCE = 0.4 V 1.0 0.5 NCTR(SAT) NCTR 0.0 0.1 1 10 Normalized to: VCE = 10 V, IF = 10 mA, Tamb = 25 °C CTRCE(sat) VCE = 0.4 V NCTR - Normalized CTR NCTR - Normalized CTR 0.1 I F - LED Current (mA) iilct6_01 1.0 Tamb = 85 °C 0.5 NCTR(SAT) NCTR 0.0 100 0.1 1 I F - LED Current (mA) 10 100 IF - LED Current (mA) iilct6_02 iilct6_05 Fig. 2 - Normalized Non-Saturated and Saturated CTR vs. LED Current Fig. 5 - Normalized Non-Saturated and Saturated CTR vs. LED Current 35 Normalized to: VCE = 10 V, I F = 10 mA, TA = 25 °C ICE - Collector Current (mA) NCTR - Normalized CTR 1.5 CTRce(sat)VCE = 0.4 V 1.0 TA = 50 °C 0.5 NCTR(SAT) NCTR 25 50 °C 20 15 70 °C 25 °C 85 °C 10 5 0 0.0 0.1 1 10 100 0 I F - LED Current (mA) iilct6_06 iilct6_03 Fig. 3 - Normalized Non-Saturated and Saturated CTR vs. LED Current www.vishay.com 4 30 10 20 30 40 50 60 IF - LED Current (mA) Fig. 6 - Collector Emitter Current vs. Temperature and LED Current For technical questions, contact: [email protected] Document Number: 83651 Rev. 1.8, 09-Jan-08 ILD610 Optocoupler, Phototransistor Output, Dual Channel Vishay Semiconductors VCC = 5 V ICEO - Collector Emitter (nA) 10 5 10 4 F = 10 kHz, DF = 50 % 10 3 RL 10 2 Vce = 10 V 10 1 Typical 10 0 VO IF = 10 mA 10 - 1 10 - 2 - 20 0 20 40 60 80 100 Tamb - Ambient Temperature (°C) iild610_10 iilct6_07 Fig. 7 - Collector Emitter Leakage Current vs.Temperature 1000 tpHL 100 2.0 10 1.5 tpLH 1 0.1 1 tpHL - Propagation Delay (µs) 2.5 Tamb = 25 °C, IF = 10 mA VCC = 5 V, Vth = 1.5 V tpLH - Propagation (µs) Fig. 10 - Non-Saturated Switching Schematic 1.0 100 10 R L - Collector Load Resistor (kΩ) Input toff ton tpdoff tpdon Output td tr 10 % ts tr 10 % 50 % 50 % 90 % 90 % iild610_11 iilct6_08 Fig. 8 - Propagation Delay vs. Collector Load Resistor Fig. 11 - Saturated Switching Time Test Waveform IF tD tR VO t PLH V TH = 1.5 V t PHL iild610_09 tS tF Fig. 9 - Switching Timing Document Number: 83651 Rev. 1.8, 09-Jan-08 For technical questions, contact: [email protected] www.vishay.com 5 ILD610 Optocoupler, Phototransistor Output, Dual Channel Vishay Semiconductors PACKAGE DIMENSIONS in inches (millimeters) Pin one ID 4 3 2 1 5 6 7 8 0.255 (6.48) 0.268 (6.81) ISO method A 0.379 (9.63) 0.390 (9.91) 0.030 (0.76) 0.045 (1.14) 0.300 (7.62) typ. 0.031 (0.79) 4° typ. 0.130 (3.30) 0.150 (3.81) 0.050 (1.27) 0.020 (0.51) 0.018 (0.46) 0.022 (0.56) 0.230 (5.84) 10° 0.035 (0.89) 0.100 (2.54) typ. i178006 0.110 (2.79) 0.008 (0.20) 0.012 (0.30) Option 6 Option 7 Option 9 0.407 (10.36) 0.391 (9.96) 0.307 (7.8) 0.291 (7.4) 0.300 (7.62) typ. 0.375 (9.53) 0.395 (10.03 ) 0.300 (7.62) ref. 0.028 (0.7) min. 0.315 (8.0) min. 0.014 (0.35) 0.010 (0.25) 0.400 (10.16) 0.430 (10.92) www.vishay.com 6 0.250 (6.35) 0.130 (3.30) 3° to 9° 0.331 (8.4) min. 0.406 (10.3) max. 0.180 (4.6) 0.160 (4.1) 0.0040 (0.102) 0.0098 (0.249) 0.012 (0.30 ) typ. 0.020 (0.51 ) 0.040 (1.02 ) 15° max. 0.315 (8.00) min. For technical questions, contact: [email protected] 18450 Document Number: 83651 Rev. 1.8, 09-Jan-08 ILD610 Optocoupler, Phototransistor Output, Dual Channel Vishay Semiconductors OZONE DEPLETING SUBSTANCES POLICY STATEMENT It is the policy of Vishay Semiconductor GmbH to 1. Meet all present and future national and international statutory requirements. 2. Regularly and continuously improve the performance of our products, processes, distribution and operating systems with respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment. It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone depleting substances (ODSs). The Montreal Protocol (1987) and its London Amendments (1990) intend to severely restrict the use of ODSs and forbid their use within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances. Vishay Semiconductor GmbH has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in the following documents. 1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively. 2. Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental Protection Agency (EPA) in the USA. 3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C (transitional substances) respectively. Vishay Semiconductor GmbH can certify that our semiconductors are not manufactured with ozone depleting substances and do not contain such substances. We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications. All operating parameters must be validated for each customer application by the customer. Should the buyer use Vishay Semiconductors products for any unintended or unauthorized application, the buyer shall indemnify Vishay Semiconductors against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use. Vishay Semiconductor GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany Document Number: 83651 Rev. 1.8, 09-Jan-08 For technical questions, contact: [email protected] www.vishay.com 7 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1