VISHAY 152D685X9015A2T

152D
www.vishay.com
Vishay Sprague
Solid-Electrolyte TANTALEX® Capacitors,
Extended Capacitance Values, Hermetically-Sealed
FEATURES
• Axial through-hole terminatons: Tin/lead
(SnPb), 100 % tin (RoHS compliant)
• High capacitance and small size
• Exceptional operating stability
• Hermetically-sealed, cylindrical, metal-case
• Low leakage current and low dissipation
factor
• The military equivalent to the 152D is the CSR23 which is
qualified to MIL-C-39003/03
• Provide proven reliability in a wide variety of high
performance military, industrial and commercial markets
• Material categorization: For definitions please see
www.vishay.com/doc?99912
Note
* Lead (Pb)-containing terminations are not RoHS-compliant.
Exemptions may apply.
PERFORMANCE CHARACTERISTICS
Operating Temperature: - 55 °C to + 85 °C
(to + 125 °C with voltage derating)
Capacitance Tolerance: At 120 Hz, + 25 °C
± 20 % and ± 10 % standard. ± 5 % available as special
Dissipation Factor: At 120 Hz, + 25 °C
Dissipation factor, as determined from the expression
2fRC, shall not exceed the values listed in the Standard
Ratings table
DC Leakage Current (DCL Max.):
At + 25 °C: Leakage current shall not exceed the values
listed in the Standard Ratings table
At + 85 °C: Leakage current shall not exceed 10 times the
values listed in the Standard Ratings table
At + 125 °C: Leakage shall not exceed 12 times the values
listed in the Standard Ratings table
Life Test: Capacitors shall withstand rated DC voltage
applied at + 85 °C for 2000 h or derated DC voltage applied
at + 125 °C for 1000 h
Following the life test:
1. DCL shall not exceed 125 % of the initial requirement. In
no case need the leakage current be less than 2 µA
2. Dissipation factor shall meet the initial requirement
3. Change in capacitance shall not exceed ± 5 %
ORDERING INFORMATION
152D
106
X0
006
A
2
T
E3
MODEL
CAPACITANCE
CAPACITANCE
TOLERANCE
DC VOLTAGE RATING
AT 85 °C
CASE
CODE
STYLE
NUMBER
PACKAGING
RoHS
COMPLIANT
This is expressed
in picofarads. The
first two digits are
the significant
figures. The third
is the number of
zeros to follow.
X0 = ± 20 %
X9 = ± 10 %
X5 = ± 5 % *
* Special order
This is expressed in
volts. To complete the
three-digit block,
zeros precede the
voltage rating.
See
Ratings
and Case
Codes
table
2 = Insulated
sleeve
T = Tape
and reel
E3 = 100 % tin
termination
(RoHS compliant)
Blank = SnPb
termination
DIMENSIONS in inches [millimeters]
1.500 ± 0.250
[38.10 ± 6.35]
1.500 ± 0.250
[38.10 ± 6.35]
L
Positive lead
D
dia.
+
-
Solid tinned
nickel leads
0.047 [1.19] max.
0.125 [3.18] max.
J max.
CASE CODE
A
B
R
S
D
L
WITH INSULATING SLEEVE (1)
0.135 ± 0.016 [3.43 ± 0.41] 0.286 ± 0.031 [7.26 ± 0.79]
0.185 ± 0.016 [4.70 ± 0.41] 0.474 ± 0.031 [12.04 ± 0.79]
0.289 ± 0.016 [7.34 ± 0.41] 0.686 ± 0.031 [17.42 ± 0.79]
0.351 ± 0.016 [8.92 ± 0.41] 0.786 ± 0.031 [19.96 ± 0.79]
J
(MAXIMUM)
0.422 [10.72]
0.610 [15.49]
0.822 [20.88]
0.922 [23.42]
AWG NO.
24
24
22
22
LEAD SIZE
NOMINAL DIAMETER
0.020 [0.51]
0.020 [0.51]
0.025 [0.64]
0.025 [0.64]
Note
(1) When a shrink-fitted insulation is used, it shall lap over the ends of the capacitor body
Revision: 09-Mar-12
Document Number: 40016
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
152D
www.vishay.com
Vishay Sprague
STANDARD RATINGS
CAPACITANCE
(μF)
CASE CODE
PART NUMBER
MAX. DCL
AT + 25 °C
(μA)
MAX. DF
AT + 25 °C
120 Hz
(%)
6 VDC AT + 85 °C, SURGE = 8 V; 4 VDC AT + 125 °C, SURGE = 5 V
10
12
15
68
82
100
330
390
470
560
680
820
1000
A
A
A
B
B
B
R
R
R
S
S
S
S
152D106(1)006A2
152D126(1)006A2
152D156(1)006A2
152D686(1)006B2
152D826(1)006B2
152D107(1)006B2
152D337(1)006R2
152D397(1)006R2
152D477(1)006R2
152D567(1)006S2
152D687(1)006S2
152D827(1)006S2
152D108(1)006S2
1.0
1.0
1.0
3.0
3.0
6.0
10.0
10.0
10.0
20.0
20.0
20.0
20.0
6
6
6
6
6
6
8
8
8
10
10
10
10
10 VDC AT + 85 °C, SURGE = 13 V; 7 VDC AT + 125 °C, SURGE = 9 V
5.6
6.8
8.2
10
47
56
68
82
150
180
220
270
330
390
470
560
A
A
A
A
B
B
B
B
R
R
R
R
S
S
S
S
152D565(1)010A2
152D685(1)010A2
152D825(1)010A2
152D106(1)010A2
152D476(1)010B2
152D566(1)010B2
152D686(1)010B2
152D826(1)010B2
152D157(1)010R2
152D187(1)010R2
152D227(1)010R2
152D277(1)010R2
152D337(1)010S2
152D397(1)010S2
152D477(1)010S2
152D567(1)010S2
1.0
1.0
1.2
1.2
4.0
5.0
6.0
7.0
8.0
8.0
12.0
13.0
16.0
16.0
16.0
20.0
4
6
6
6
6
6
6
6
8
8
8
8
8
10
10
10
15 VDC AT + 85 °C, SURGE = 20 V; 10 VDC AT + 125 °C, SURGE = 12 V
3.9
4.7
5.6
6.8
27
33
39
82
100
120
150
180
220
270
330
A
A
A
A
B
B
B
R
R
R
R
R
S
S
S
152D395(1)015A2
152D475(1)015A2
152D565(1)015A2
152D685(1)015A2
152D276(1)015B2
152D336(1)015B2
152D396(1)015B2
152D826(1)015R2
152D107(1)015R2
152D127(1)015R2
152D157(1)015R2
152D187(1)015R2
152D227(1)015S2
152D277(1)015S2
152D337(1)015S2
1.0
1.0
1.3
1.3
3.0
5.0
5.0
8.0
10.0
10.0
15.0
15.0
20.0
20.0
20.0
4
4
4
6
6
6
6
6
8
8
8
8
8
8
8
Note
• Part number definitions:
(1) For 10 % tolerance specify X9; for 20 % specify “X0”; for 5 % “X5” (special order)
Revision: 09-Mar-12
Document Number: 40016
2
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
152D
www.vishay.com
Vishay Sprague
STANDARD RATINGS
CAPACITANCE
(μF)
2.7
3.3
3.9
4.7
18
22
27
56
68
82
100
120
150
180
220
2.2
2.7
12
15
18
56
68
82
100
1.2
1.5
1.8
8.2
10
27
33
39
47
56
68
82
100
1.2
1.5
5.6
6.8
22
27
33
39
47
CASE CODE
PART NUMBER
20 VDC AT + 85 °C, SURGE = 26 V; 13 VDC AT + 125 °C, SURGE = 16 V
A
152D275(1)020A2
0.8
A
152D335(1)020A2
1.0
A
152D395(1)020A2
1.2
A
152D475(1)020A2
1.2
B
152D186(1)020B2
3.0
B
152D226(1)020B2
3.0
B
152D276(1)020B2
4.0
R
152D566(1)020R2
7.0
R
152D686(1)020R2
8.0
R
152D826(1)020R2
10.0
R
152D107(1)020R2
12.0
R
152D127(1)020R2
12.0
S
152D157(1)020S2
15.0
S
152D187(1)020S2
15.0
S
152D227(1)020S2
15.0
30 VDC AT + 85 °C, SURGE = 39 V; 20 VDC AT + 125 °C, SURGE = 26 V
A
152D225(1)030A2
1.0
A
152D275(1)030A2
1.0
B
152D126(1)030B2
3.0
B
152D156(1)030B2
3.0
B
152D186(1)030B2
3.0
R
152D566(1)030R2
7.0
R
152D686(1)030R2
7.0
S
152D826(1)030S2
10.0
S
152D107(1)030S2
10.0
35 VDC AT + 85 °C, SURGE = 46 V; 23 VDC AT + 125 °C, SURGE = 28 V
A
152D125(1)035A2
0.6
A
152D155(1)035A2
0.8
A
152D185(1)035A2
1.0
B
152D825(1)035B2
3.0
B
152D106(1)035B2
3.0
R
152D276(1)035R2
7.0
R
152D336(1)035R2
8.0
R
152D396(1)035R2
10.0
R
152D476(1)035R2
10.0
S
152D566(1)035S2
12.0
S
152D686(1)035S2
12.0
S
152D826(1)035S2
30.0
S
152D107(1)035S2
30.0
50 VDC AT + 85 °C, SURGE = 65 V; 33 VDC AT + 125 °C, SURGE = 40 V
A
152D125(1)050A2
0.6
A
152D155(1)050A2
0.8
B
152D565(1)050B2
2.5
B
152D685(1)050B2
2.5
R
152D226(1)050R2
7.0
R
152D276(1)050R2
8.0
S
152D336(1)050S2
10.0
S
152D396(1)050S2
10.0
S
152D476(1)050S2
10.0
60 VDC AT + 85 °C, SURGE = 78 V; 39 VDC AT + 125 °C, SURGE = 49 V
R
152D226(1)060R2
7
22
Note
• Part number definitions:
(1) For 10 % tolerance specify X9; for 20 % specify “X0”; for 5 % “X5” (special order)
Revision: 09-Mar-12
MAX. DCL
AT + 25 °C
(μA)
MAX. DF
AT + 25 °C
120 Hz
(%)
4
4
4
4
4
4
4
6
6
6
6
6
8
8
8
4
4
4
4
4
6
6
8
8
4
4
4
4
4
6
6
6
6
6
6
8
8
4
4
4
4
6
6
6
6
6
6
Document Number: 40016
3
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
152D
www.vishay.com
Vishay Sprague
STANDARD REEL PACKAGING SPECIFICATIONS - MEETS EIA STANDARD RS-296 in inches [millimeters]
“A”
13.0 [330.2]
Tape spacing
Standard reel
B
1.126 to 3.07
[28.6 to 78.0]
A
I. D. reel hub
Component
spacing
1.374 to 3.626
[34.9 to 92.1]
0.031 [0.79] max.
Off center (1. a)
0.625 ± 0.0062 dia.
[15.88 ± 1.575]
Thru hole
0.125 [3.18] max.
0.250 [6.35] (3. b)
CASE
CODE
0.750 [19.05]
“A”
Label (4. a)
0.031 [0.79] (3. f)
Section “A” to “A”
TYPE 150D UNITS WITH
INSULATING SLEEVE
Both sides (3. f)
COMPONENT
SPACING
LEAD SIZE
TAPE SPACING
UNITS
PER REEL
D
L
AWG NO.
NOM. DIA.
A
B
A
0.135 ± 0.016
[3.43 ± 0.41]
0.286 ± 0.031
[7.26 ± 0.79]
24
0.020
[0.51]
0.200 ± 0.015
[5.08 ± 0.38]
2.500 ± 0.062
[63.5 ± 1.57]
1000
B
0.185 ± 0.016
[4.70 ± 0.41]
0.474 ± 0.031
[12.04 ± 0.79]
24
0.020
[0.51]
0.200 ± 0.015
[5.08 ± 0.38]
2.500 ± 0.062
[63.5 ± 1.57]
1000
R
0.289 ± 0.016
[7.34 ± 0.41]
0.686 ± 0.031
[17.42 ± 0.79]
22
0.025
[0.64]
0.400 ± 0.015
[10.16 ± 0.38]
2.875 ± 0.062
[73.03 ± 1.57]
500
S
0.351 ± 0.016
[8.92 ± 0.41]
0.786 ± 0.031
[19.96 ± 0.79]
22
0.025
[0.64]
0.400 ± 0.015
[10.16 ± 0.38]
2.875 ± 0.062
[73.03 ± 1.57]
500
STANDARD REEL PACKAGING INFORMATION
1. Component Leads
a. Component leads shall not be bent beyond 0.047"
[1.19 mm] maximum from their nominal position when
measured from the leading edge of the component lead
at the lead egress from the component.
b. The “C” dimension shall be governed by the overall
length of the reel packaged component. The distance
between flanges shall be 0.125" to 0.250" [3.18 mm to
6.35 mm] greater than the overall component length.
2. Orientation
All polarized components must be oriented to one
direction. The cathode lead tape shall be a color and the
anode lead tape shall be white.
3. Reeling
a. Components on any reel shall not represent more than
two date codes when date code identification is required.
b. Component leads shall be positioned between pairs of
0.250" [6.35 mm] tape.
c. The disposable reels have hubs and corrugated
fibreboard flanges and core or equivalent.
d. A minimum of 12.0" [304.8 mm] leader of tape shall be
provided before the first and after the last component on
the reel.
e. 50 lb or 60 lb. Kraft paper must be wound between layer
of components as far as necessary for component
protection. Width of paper to be 0.062" to 0.250"
[1.57 mm to 6.35 mm] less than the “C” dimension
of the reel.
Revision: 09-Mar-12
f. A row of components must be centered between tapes
± 0.047" [1.19 mm]. In addition, individual components
may deviate from center of component row ± 0.031"
[0.79 mm].
g. Staples shall not be used for splicing. Not more than
4 layers of tape shall be used in any splice area and no
tape shall be offset from another by more than 0.031"
[0.79 mm] non-cumulative. Tape splices shall overlap at
least 6.0" [152.4 mm] for butt joints and at least 3.0"
[76.2 mm] for lap joints and shall not be weaker than
unspliced tape. Universal splicing clips may also be used.
h. Quantity per reel shall be controlled so that tape
components and cover shall not extend beyond the
smallest dimension of the flange (either across flats or
diameter). Once the quantity per reel for each part
number has been established, future orders for that part
number shall be packaged in that quantity. When order or
release quantity is less than the established quantity, a
standard commercial pack is to be used.
i. A maximum of 0.25 % of the components per reel
quantity may be missing without consecutive missing
components.
j. Adequate protection must be provided to prevent
physical damage to both reel and components during
shipment and storage.
4. Marking
Minimum reel and carton marking shall consist of the
following: Customer part number, purchase order no.,
quantity, package date, manufacturer’s name, electrical
value, date code, Vishay Sprague part number and
country of origin.
Document Number: 40016
4
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000