MEANWELL PSD-15C-05

P S D - 1 5 series
15W DC-DC Single Output Switching Power Supply
Features :
Protections:Short circuit/Over load /Over voltage/Polarity
Cooling by free air convection
100% full load burn-in test
Low cost
High reliability
2 year warranty
SPECIFICATION
DC VOLTAGE
RATED CURRENT
CURRENT RANGE
OUTPUT
RATED POWER
RIPPLE & NOISE (max.) Note.2
VOLTAGE TOLERANCE Note.3
LINE REGULATION
LOAD REGULATION
SETUP, RISE, HOLD UP TIME
INPUT
PROTECTION
5V
PSD-15B-12 PSD-15C-12
PSD-15A-24 PSD-15B-24 PSD-15C-24
3A
0 ~ 3A
15W
15W
50mVp-p
100mVp-p
2.0%
2.0%
2.0%
1.0%
1.0%
1.0%
1.0%
2.5s, 25ms, ----/12VDC/24VDC/48VDC at full load
0.5%
VOLTAGE RANGE
A: 9.2 ~18VDC (12VDC)
74%
DC CURRENT(Typ.)
1.9A/12VDC 0.9A/24VDC 0.45A/48VDC
105% -150% rated output power
OVER LOAD
PSD-15A-12
12V
1.25A
0 ~ 1.25A
EFFICIENCY(Typ.)
OVER VOLTAGE
ENVIRONMENT
PSD-15B-05 PSD-15C-05
PSD-15A-05
MODEL
78%
B:18 ~ 36VDC (24VDC)
78%
67%
24V
0.6A
0 ~ 0.6A
14.4W
100mVp-p
0.5%
C:36~72VDC(48VDC)
78%
78%
78%
72%
79%
Protection type : hiccup mode ,recovery automatically after fault condition is removed
5.75 ~ 6.75V
13.8~ 16.2V
¡
WORKING TEMP.
Protection type : Shut off o/p voltage, clamping by zener diode
-10 60
20 ~ 90% RH non-condensing
WORKING HUMIDITY
20 ~ 95% RH non-condensing
27.6 ~ 32.4V
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
SAFETY &
EMC
VIBRATION
WITHSTAND VOLTAGE
10 ~ 500Hz, 2G 10min./1cycle, Period for 60min.each along X, Y, Z axes
I/P-O/P:2KVAC
ISOLATION RESISTANCE
I/P-O/P:100M Ohms/500VDC / 25
/ 70% RH
EMI CONDUCTION&RADIATION Compliance to EN55022(CISPR22) CLASS B
OTHERS
NOTE
EMS IMMUNITY
Compliance to EN61000-4-2, 3, 4, 6, 8 EN55024, EN61000-6-1 Light industry level, criteria A
MTBF
740.4Khrs min. MIL-HDBK-217F(25
DIMENSION
94*49*25mm (L*W*H)
PACKING
81mg;120pcs/10.72Kg
)
1.All parameters NOT specially mentioned are measured at normal input,rated load and 25 of ambient temperature.
2.Ripple & noise are measued at 20 MHz of bandwidth by using a 12inch twisted pair-wire termined with a 0.1uf & 47uf capacitor.
3.Tolerance:includes set up tolerance,line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed
that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power
supplies.” (as available on http://www.meanwell.com)
File Name:PSD-15-SPEC 2011-03-09
P S D - 1 5 series
15W DC-DC Single Output Switching Power Supply
Mechanical Specification
Unit:mm
94
3.5
87
1
2
4
42
1
2
3
4 4
49
26
4-3.5 Dia
Mounting Holes
CN2
2 max.
25
3.5
16
CN1
DC Input Connector (CN1) : JST B3P-VH or equivalent
Pin No.
1
2
3
Mating Housing
Assignment
-V
No Pin
+V
JST VHR
or equivalent
DC Output Connector (CN2) : JST B2P-VH or equivalent
Terminal
JST SVH-21T-P1.1
or equivalent
Pin No.
1
2
Assignment
-V
+V
Mating Housing
JST VHR
or equivalent
Block Diagram
fosc : 100KHz
EMI
FILTER
I/P
Terminal
JST SVH-21T-P1.1
or equivalent
RECTIFIERS
&
FILTER
POWER
SWITCHING
OLP
PWM
CONTROL
RECTIFIERS
&
FILTER
+V
-V
DETECTION
CIRCUIT
Output Derating
100
80
LOAD (%)
60
40
20
-10
-10
0
10
20
30
40
AMBIENT TEMPERATURE (
50
45
60
55
(HORIZONTAL)
(VERTICAL)
)
File Name:PSD-15-SPEC 2011-03-09