PS-25 25W Single Output Switching Power Supply series Features : Universal AC input / Full range Low leakage current <0.5mA Protections:Short circuit/Over load/Over voltage/Over temperature Cooling by free air convection 100% full load burn-in test Fixed switching frequency at 100KHz Low cost High reliability 2 years warranty SPECIFICATION MODEL OUTPUT INPUT PS-25-3.3 PS-25-5 PS-25-7.5 PS-25-12 PS-25-13.5 PS-25-15 PS-25-24 PS-25-27 PS-25-48 DC VOLTAGE 3.3V 5V 7.5V 12V 13.5V 15V 24V 27V 48V RATED CURRENT 5A 5A 3.3A 2.1A 1.9A 1.7A 1A 0.9A 0.5A CURRENT RANGE 0 ~ 5A 0 ~ 5A 0 ~ 3.3A 0 ~ 2.1A 0 ~ 1.9A 0 ~ 1.7A 0 ~ 1A 0 ~ 0.9A 0 ~ 0.5A RATED POWER 16.5W 25W 24.8W 25.2W 25.7W 25.5W 24W 24.3W 24W 100mVp-p 100mVp-p 100mVp-p 240mVp-p 240mVp-p 350mVp-p RIPPLE & NOISE (max.) Note.2 80mVp-p 80mVp-p 80mVp-p VOLTAGE TOLERANCE Note.3 3.0% 2.0% 2.0% 2.0% 2.0% 2.0% 2.0% 2.0% 2.0% LINE REGULATION 0.5% 0.5% 0.5% 0.3% 0.3% 0.3% 0.2% 0.2% 0.2% LOAD REGULATION 2.5% 2.0% 2.0% 1.0% 1.0% 1.0% 0.5% 0.5% 0.5% SETUP, RISE TIME 200ms, 20ms/230VAC HOLD TIME (Typ.) 100ms/230VAC VOLTAGE RANGE 85 ~ 264VAC FREQUENCY RANGE 47 ~ 63Hz EFFICIENCY(Typ.) 66% AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 0.6A/115VAC LEAKAGE CURRENT OVER LOAD PROTECTION OVER VOLTAGE OVER TEMPERATURE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE SAFETY & ISOLATION RESISTANCE EMC EMI CONDUCTION & RADIATION (Note 4) HARMONIC CURRENT OTHERS 20ms/115VAC at full load 120 ~ 370VDC 74% 76% 78% 78% 79% 79% 79% COLD START 36A <0.5mA / 240VAC Above 105% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed 3.8 ~ 4.46V 5.75 ~ 6.75V 8.6 ~ 10.1V 13.8 ~ 16.2V 15.5 ~ 18.2V 17.3 ~ 20.3V 27.6 ~ 32.4V 31 ~ 36.5V 55.2 ~ 64.8V Protection type : Shut down o/p voltage, re-power on to recover Tj 135 typically (U1) Detect on main control IC Protection type : Shut down o/p voltage, recovers automatically after temperature goes down -10 ~ +60 (Refer to output load derating curve) 20 ~ 90% RH non-condensing -20 ~ +85 , 10 ~ 95% RH 0.03%/ (0 ~ 50 10 ~ 500Hz, 2G 10min./1cycle, Period for 60min.each along X, Y, Z axes UL60950-1, TUV EN60950-1 Approved I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC Compliance to EN55022 (CISPR22) Class B Compliance to EN61000-3-2,-3 Compliance to EN61000-4-2,3,4,5, Light industry level, criteria A MTBF 576.4Khrs min. MIL-HDBK-217F (25 107*61*28mm (L*W*H) 0.14Kg; 96pcs/15Kg/1.3CUFT DIMENSION 78% 0.4A/230VAC EMS IMMUNITY PACKING NOTE 200ms, 30ms/115VAC at full load ) 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. File Name:PS-25-SPEC 2005-10-03 PS-25 25W Single Output Switching Power Supply Mechanical Specification series Unit:mm 107 6.35 94 4-3.5 Dia Mounting Holes 1 2 3 4 AC FUSE 2.5A/250V 3.81 53 61 1 2 3 CN1 CN2 28 To Chassis Grounding AC Input Connector (CN1) : Molex 41791-03 or equivalent Assignment AC/L No Pin AC/N Pin No. 1 2 3 Mating Housing Terminal Molex 2139 or equivalent Molex 2478 or equivalent DC Output Connector (CN2) : Molex 41791-04 or equivalent Pin No. 1,2 3,4 Assignment +V -V Mating Housing Molex 2139 or equivalent Terminal Molex 2478 or equivalent Block Diagram fosc : 100KHz RECTIFIERS & FILTER EMI FILTER I/P RECTIFIERS & FILTER POWER SWITCHING PWM CONTROL -V DETECTION CIRCUIT FG Output Derating +V Static Characteristics (24V) OUTPUT VOLTAGE (V) 100 80 LOAD (%) 60 40 20 350 28 300 24 250 20 200 16 150 12 100 50 8 -10 -10 0 10 20 30 40 50 45 AMBIENT TEMPERATURE ( ) 60 55 (HORIZONTAL) (VERTICAL) OUTPUT RIPPLE (mVp-p) Ta=25 32 60 80 100 120 140 160 180 200 220 240 260 INPUT VOLTAGE (V) 60Hz File Name:PS-25-SPEC 2005-10-03 PS-45 45W Single Output Switching Power Supply series Features : Universal AC input/Full range Low leakage current<0.5mA Protections:Short circuit/Over load/Over voltage Cooling by free air convection 100% full load burn-in test Fixed switching frequency at 65KHz 2 years warranty SPECIFICATION MODEL OUTPUT INPUT PS-45-3.3 PS-45-5 PS-45-7.5 PS-45-12 PS-45-13.5 PS-45-15 PS-45-24 PS-45-27 DC VOLTAGE 3.3V 5V 7.5V 12V 13.5V 15V 24V 27V 48V RATED CURRENT 8A 8A 5.4A 3.7A 3.3A 3A 1.9A 1.7A 1A CURRENT RANGE 0 ~ 10.7A 0 ~ 10.5A 0 ~ 7A 0 ~ 4.4A 0 ~ 3.9A 0 ~ 3.5A 0 ~ 2.2A 0 ~ 1.95A 0 ~ 1.1A RATED POWER 26.4W 40W 40.5W 44.4W 44.6W 45W 45.6W 45.9W 48W OUTPUT POWER (max.) Rated output power for convection; 52W (+3.3V : 35W) with 18 CFM min. 100mVp-p 100mVp-p 100mVp-p 100mVp-p RIPPLE & NOISE (max.) Note.2 80mVp-p 100mVp-p VOLTAGE ADJ. RANGE 3.14 ~ 3.63V 4.75 ~ 5.5V VOLTAGE TOLERANCE Note.3 3.0% 3.0% 100mVp-p 100mVp-p 100mVp-p PS-45-48 7.13 ~ 8.25V 11.4 ~ 13.2V 12.8 ~ 14.85V 14.25 ~ 16.5V 22.8 ~ 26.4V 25.65 ~ 29.7V 45.6 ~ 52.8V 3.0% 2.0% 2.0% 2.0% 2.0% 2.0% 2.0% LINE REGULATION 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% LOAD REGULATION 3.0% 3.0% 3.0% 2.0% 2.0% 2.0% 2.0% 2.0% 2.0% SETUP, RISE TIME 800ms, 30ms at full load HOLD TIME (Typ.) 60ms at full load VOLTAGE RANGE 90 ~ 264VAC FREQUENCY RANGE 47 ~ 440Hz EFFICIENCY(Typ.) 69% AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 0.8A/115VAC LEAKAGE CURRENT OVER LOAD PROTECTION OVER VOLTAGE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE 127 ~370VDC 74% 75% 76% 77% 77% 78% 78% 78% 0.56A/230VAC COLD START 15A/115VAC <0.75mA / 240VAC 30A/230VAC 53 ~ 75W(3.3V : 36 ~ 55W) rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed. 3.8 ~ 4.46V 5.75 ~ 6.75V 8.63 ~ 10.1V 13.8 ~ 16.2V 15.5 ~ 18.2V 17.25 ~ 20.25V 27.6 ~ 32.4V 31 ~ 36.45V 55.2 ~ 64.8V Protection type : Hiccup mode, recovers automatically after fault condition is removed. -10 ~ +60 (Refer to output load derating curve) 20 ~ 90% RH non-condensing -20 ~ +85 , 10 ~ 95% RH 0.05%/ (0 ~ 50 10 ~ 500Hz, 2G 10min./1cycle, Period for 60min.each along X, Y, Z axes UL60950, TUV EN60950-1 Approved I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC SAFETY & ISOLATION RESISTANCE EMC (Note 4) I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B HARMONIC CURRENT Compliance to EN61000-3-2,-3 EMS IMMUNITY MTBF OTHERS DIMENSION PACKING NOTE Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, Light industry level, criteria A 300.7K hrs min. MIL-HDBK-217F (25 ) 127*76*28mm (L*W*H) 0.19Kg; 72pcs/15.6Kg/1.35CUFT 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 5. Mounting holes M1 and M2 should be grounded for EMI purposes. File Name:PS-45-SPEC 2006-01-27 PS-45 45W Outputs Switching Power Supply Mechanical Specification series Unit:mm 127 5.6 5.6 115.8 FG M2 M1 CN1 64.8 CN2 1 2 3 4 5 6 2 AC FUSE F4A/250V 76 1 4- 8 28 3. AC Input Connector (CN1) : Molex 5277-02 or equivalent Pin No. 1 2 Assignment AC/N AC/L Mating Housing Terminal Molex 5195 or equivalent Molex 5194 or equivalent DC Output Connector (CN2) : Molex 5273-06 or equivalent Pin No. 1,2,3 4,5,6 Assignment +V -V Terminal Molex 5194 or equivalent Mating Housing Molex 5195 or equivalent Block Diagram fosc : 65KHz POWER SWITCHING RECTIFIERS & FILTER EMI FILTER I/P FG RECTIFIERS & FILTER DETECTION CIRCUIT PWM CONTROL O.L.P. Output Derating +V -V O.V.P. Static Characteristics (12V) Ta=25 OUTPUT VOLTAGE (V) 80 LOAD (%) 60 3.3V,5V 40 20 -10 0 10 20 30 40 50 AMBIENT TEMPERATURE ( ) 60 (HORIZONTAL) 250 14 +12V 12 200 10 150 8 +12V 100 6 50 4 25 60 80 100 120 140 160 180 200 220 240 OUTPUT RIPPLE (mVp-p) OTHERS 100 300 16 260 INPUT VOLTAGE (V) 60Hz File Name:PS-45-SPEC 2006-01-27 PS-65 65W Single Output Switching Power Supply series Features : Universal AC input/Full range Low leakage current<0.5mA Protections: Short circuit / Overload / Over voltage Cooling by free air convection 100% full load burn-in test Fixed switching frequency at 65KHz 2 years warranty SPECIFICATION MODEL OUTPUT INPUT PS-65-3.3 PS-65-5 PS-65-7.5 PS-65-12 PS-65-13.5 PS-65-15 PS-65-24 PS-65-27 DC VOLTAGE 3.3V 5V 7.5V 12V 13.5V 15V 24V 27V 48V RATED CURRENT 12A 12A 8A 5.2A 4.7A 4.2A 2.7A 2.4A 1.35A CURRENT RANGE 0 ~ 15.2A 0 ~ 13.8A 0 ~ 9.6A 0 ~ 6A 0 ~ 5.4A 0 ~ 4.8A 0 ~ 3A 0 ~ 2.7A 0 ~ 1.5A RATED POWER 39.6W 60W 60W 62.4W 63.5W 63W 64.8W 64.8W 64.8W OUTPUT POWER (max.) Rated output power for convection; 72W (+3.3V : 50W;+5V:69W) with 18 CFM min. Forced air 100mVp-p 100mVp-p RIPPLE & NOISE (max.) Note.2 80mVp-p 3.14 ~ 3.63V 4.75 ~ 5.5V VOLTAGE TOLERANCE Note.3 3.0% 3.0% 100mVp-p 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% 3.0% 3.0% 2.0% 2.0% 2.0% 2.0% 2.0% 2.0% 79% 80% 80% 80% SETUP, RISE TIME 800ms, 20ms at full load HOLD UP TIME (Typ.) 60ms at full load VOLTAGE RANGE 90 ~ 264VAC FREQUENCY RANGE 47 ~ 440Hz EFFICIENCY(Typ.) 69% AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 1.2A/115VAC WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE 127 ~370VDC 76% 79% 79% 79% 0.72A/230VAC COLD START 20A/115VAC <0.75mA / 240VAC 40A/230VAC 73 ~ 105W(3.3V : 51 ~ 75W)(5V : 70 ~ 105W) rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed. 3.8 ~ 4.46V 5.75 ~ 6.75V 8.63 ~ 10.1V 13.8 ~ 16.2V 15.5 ~ 18.2V 17.25 ~ 20.25V 27.6 ~ 32.4V 31 ~ 36.45V 55.2 ~ 64.8V Protection type : Hiccup mode, recovers automatically after fault condition is removed. -10 ~ +60 (Refer to output load derating curve) 20 ~ 90% RH non-condensing -20 ~ +85 , 10 ~ 95% RH 0.04%/ (0 ~ 50 10 ~ 500Hz, 2G 10min./1cycle, Period for 60min.each along X, Y, Z axes UL60950-1, TUV EN60950-1 Approved I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B HARMONIC CURRENT Compliance to EN61000-3-2,-3 EMS IMMUNITY MTBF Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, Light industry level, criteria A DIMENSION PACKING NOTE 100mVp-p 3.0% OVER VOLTAGE OTHERS 100mVp-p 1.0% PROTECTION (Note 4) 100mVp-p 7.13 ~ 8.25V 11.4 ~ 13.2V 12.8 ~ 14.9V 14.25 ~ 16.5V 22.8 ~ 26.4V 25.65 ~ 29.7V 45.6 ~ 52.8V 3.0% 2.0% 2.0% 2.0% 2.0% 2.0% 2.0% LOAD REGULATION OVERLOAD EMC 100mVp-p LINE REGULATION LEAKAGE CURRENT SAFETY & 100mVp-p VOLTAGE ADJ. RANGE PS-65-48 300.7K hrs min. MIL-HDBK-217F (25 127*76*42mm (L*W*H) 0.21Kg; 54pcs/14.2Kg/1.35CUFT ) 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 5. Mounting holes M1 and M2 should be grounded for EMI purposes. File Name:PS-65-SPEC 2007-03-14 PS-65 65W Single Output Switching Power Supply Mechanical Specification series Unit:mm 127 5.6 5.6 115.8 FG M2 M1 CN1 64.8 76 1 CN2 1 2 3 4 5 6 2 AC FUSE F4A/250V 43. 42 8 AC Input Connector (CN1) : Molex 5277-02 or equivalent Pin No. 1 2 Assignment AC/N AC/L Mating Housing Terminal Molex 5195 or equivalent Molex 5194 or equivalent DC Output Connector (CN2) : Molex 5273-06 or equivalent Pin No. 1,2,3 4,5,6 Assignment +V -V Terminal Molex 5194 or equivalent Mating Housing Molex 5195 or equivalent Block Diagram fosc : 65KHz RECTIFIERS & FILTER EMI FILTER I/P POWER SWITCHING RECTIFIERS & FILTER FG O.L.P. DETECTION CIRCUIT PWM CONTROL Derating Curve +V -V O.V.P. Output Derating VS Input Voltage Ta=25 100 100 OTHERS 90 85 80 80 70 3.3V,5V LOAD (%) LOAD (%) 60 40 20 -10 0 10 20 30 40 50 AMBIENT TEMPERATURE ( ) 60 (HORIZONTAL) 60 50 40 90 95 100 115 120 140 160 180 200 220 240 264 INPUT VOLTAGE (VAC) 60Hz File Name:PS-65-SPEC 2007-03-14