P S D - 1 5 series 15W DC-DC Single Output Switching Power Supply ■ Features : Protections:Short circuit/Over load /Over voltage/Polarity Cooling by free air convection 100% full load burn-in test Low cost High reliability 2 year warranty SPECIFICATION PSD-15A-05 MODEL DC VOLTAGE RATED CURRENT CURRENT RANGE OUTPUT RATED POWER RIPPLE & NOISE (max.) Note.2 VOLTAGE TOLERANCE Note.3 LINE REGULATION LOAD REGULATION SETUP, RISE, HOLD UP TIME INPUT PROTECTION PSD-15B-12 PSD-15C-12 PSD-15A-24 PSD-15B-24 PSD-15C-24 3A 0 ~ 3A 15W 15W 50mVp-p 100mVp-p 2.0% 2.0% 2.0% 1.0% 1.0% 1.0% 1.0% 2.5s, 25ms, ----/12VDC/24VDC/48VDC at full load 0.5% VOLTAGE RANGE A: 9.2 ~18VDC (12VDC) 74% DC CURRENT(Typ.) 1.9A/12VDC 0.9A/24VDC 0.45A/48VDC 105% -150% rated output power OVER LOAD PSD-15A-12 12V 1.25A 0 ~ 1.25A EFFICIENCY(Typ.) OVER VOLTAGE ENVIRONMENT PSD-15B-05 PSD-15C-05 5V 78% B:18 ~ 36VDC (24VDC) 78% 67% 24V 0.6A 0 ~ 0.6A 14.4W 100mVp-p 0.5% C:36~72VDC(48VDC) 78% 78% 78% 72% 79% Protection type : hiccup mode ,recovery automatically after fault condition is removed 5.75 ~ 6.75V 13.8~ 16.2V WORKING TEMP. Protection type : Shut off o/p voltage, clamping by zener diode -10 60 20 ~ 90% RH non-condensing WORKING HUMIDITY 20 ~ 95% RH non-condensing 27.6 ~ 32.4V STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT SAFETY & EMC VIBRATION WITHSTAND VOLTAGE 10 ~ 500Hz, 2G 10min./1cycle, Period for 60min.each along X, Y, Z axes I/P-O/P:1.5KVAC ISOLATION RESISTANCE I/P-O/P:100M Ohms/500VDC / 25℃/ 70% RH EMI CONDUCTION&RADIATION Compliance to EN55022(CISPR22) CLASS B OTHERS NOTE EMS IMMUNITY Compliance to EN61000-4-2, 3, 4, 6, 8 EN55024, EN61000-6-1 Light industry level, criteria A MTBF 740.4Khrs min. MIL-HDBK-217F(25℃) DIMENSION 94*49*25mm (L*W*H) PACKING 81mg;120pcs/10.72Kg 1.All parameters NOT specially mentioned are measured at normal input,rated load and 25 of ambient temperature. 2.Ripple & noise are measued at 20 MHz of bandwidth by using a 12inch twisted pair-wire termined with a 0.1uf & 47uf capacitor. 3.Tolerance:includes set up tolerance,line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to EMI testing of component power supplies. (as available on http://www.meanwell.com) File Name:PSD-15-SPEC 2015-05-29 P S D - 1 5 series 15W DC-DC Single Output Switching Power Supply Mechanical Specification Unit:mm 94 3.5 87 26 4-3.5 Dia Mounting Holes 42 4 CN2 1 2 3 4 4 49 1 2 2 max. 25 3.5 7.5 CN1 DC Input Connector (CN1) : JST B3P-VH or equivalent Pin No. 1 2 3 Assignment -V No Pin +V Mating Housing JST VHR or equivalent Terminal JST SVH-21T-P1.1 or equivalent DC Output Connector (CN2) : JST B2P-VH or equivalent Pin No. 1 2 Assignment -V +V Mating Housing Terminal JST SVH-21T-P1.1 or equivalent JST VHR or equivalent Block Diagram fosc : 100KHz POWER SWITCHING EMI FILTER I/P RECTIFIERS & FILTER PWM CONTROL OLP +V -V DETECTION CIRCUIT Output Derating 100 80 LOAD (%) 60 40 20 -10 -10 0 10 20 30 40 AMBIENT TEMPERATURE ( 50 45 60 55 (HORIZONTAL) (VERTICAL) ) File Name:PSD-15-SPEC 2015-05-29