VS-HFA32PA120CPbF Vishay Semiconductors HEXFRED® Ultrafast Soft Recovery Diode, 2 x 16 A FEATURES • Ultrafast and ultrasoft recovery • Very low IRRM and Qrr Base common cathode 2 • Compliant to RoHS Directive 2002/95/EC • Designed and qualified for industrial level BENEFITS TO-247AC • • • • • 1 3 Anode Anode 2 1 2 Common cathode DESCRIPTION VS-HFA32PA120CPbF is a state of the art ultrafast recovery diode. Employing the latest in epitaxial construction and advanced processing techniques it features a superb combination of characteristics which result in performance which is unsurpassed by any rectifier previously available. With basic ratings of 1200 V and 16 A per leg continuous current, the VS-HFA32PA120CPbF is especially well suited for use as the companion diode for IGBTs and MOSFETs. In addition to ultrafast recovery time, the HEXFRED® product line features extremely low values of peak recovery current (IRRM) and does not exhibit any tendency to “snap-off” during the tb portion of recovery. The HEXFRED features combine to offer designers a rectifier with lower noise and significantly lower switching losses in both the diode and the switching transistor. These HEXFRED advantages can help to significantly reduce snubbing, component count and heatsink sizes. The HEXFRED VS-HFA32PA120CPbF is ideally suited for applications in power supplies and power conversion systems (such as inverters), motor drives, and many other similar applications where high speed, high efficiency is needed. PRODUCT SUMMARY Package TO-247AC IF(AV) 2 x 16 A VR 1200 V VF at IF 3.0 V trr (typ.) 30 ns TJ max. 150 °C Diode variation Single die Reduced RFI and EMI Reduced power loss in diode and switching transistor Higher frequency operation Reduced snubbing Reduced parts count ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL Cathode to anode voltage Maximum continuous forward current VR per leg per device IF Single pulse forward current IFSM Maximum repetitive forward current IFRM Maximum power dissipation Operating junction and storage temperature range Document Number: 94073 Revision: 23-May-11 TEST CONDITIONS PD TJ, TStg TC = 100 °C VALUES UNITS 1200 V 16 32 190 A 64 TC = 25 °C 151 TC = 100 °C 60 - 55 to + 150 °C W For technical questions within your region, please contact one of the following: www.vishay.com [email protected], [email protected], [email protected] 1 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-HFA32PA120CPbF Vishay Semiconductors HEXFRED® Ultrafast Soft Recovery Diode, 2 x 16 A ELECTRICAL SPECIFICATIONS PER LEG (TJ = 25 °C unless otherwise specified) PARAMETER Cathode to anode breakdown voltage SYMBOL VBR TEST CONDITIONS IR = 100 μA IF = 16 A Maximum forward voltage VFM IF = 32 A See fig. 1 IF = 16 A, TJ = 125 °C VR = VR rated Maximum reverse leakage current IRM Junction capacitance CT VR = 200 V LS Measured lead to lead 5 mm from package body Series inductance TJ = 125 °C, VR = 0.8 x VR rated See fig. 2 See fig. 3 MIN. TYP. MAX. UNITS 1200 - - - 2.5 3.0 - 3.2 3.93 - 2.3 2.7 - 0.75 20 - 375 2000 - 27 40 pF - 8.0 - nH V μA DYNAMIC RECOVERY CHARACTERISTICS PER LEG (TJ = 25 °C unless otherwise specified) PARAMETER Reverse recovery time See fig. 5, 10 Peak recovery current See fig. 6 Reverse recovery charge See fig. 7 Peak rate of fall of recovery current during tb See fig. 8 SYMBOL TEST CONDITIONS MIN. TYP. MAX. - 30 - trr IF = 1.0 A, dIF/dt = 200 A/μs, VR = 30 V trr1 TJ = 25 °C - 90 135 trr2 TJ = 125 °C - 164 245 - 5.8 10 - 8.3 15 - 260 675 - 680 1838 UNITS ns IRRM1 TJ = 25 °C IRRM2 TJ = 125 °C Qrr1 TJ = 25 °C Qrr2 TJ = 125 °C dI(rec)M/dt1 TJ = 25 °C - 120 - dI(rec)M/dt2 TJ = 125 °C - 76 - MIN. TYP. MAX. UNITS - - 300 °C - - 0.83 IF = 16 A dIF/dt = 200 A/μs VR = 200 V A nC A/μs THERMAL - MECHANICAL SPECIFICATIONS PARAMETER SYMBOL TEST CONDITIONS Lead temperature Tlead Thermal resistance, junction to case RthJC Thermal resistance, junction to ambient RthJA Typical socket mount - - 80 Thermal resistance, case to heatsink RthCS Mounting surface, flat, smooth and greased - 0.50 - - 2.0 - - 0.07 - oz. - 12 (10) kgf · cm (lbf · in) 0.063" from case (1.6 mm) for 10 s Weight 6.0 (5.0) Mounting torque Marking device www.vishay.com 2 Case style TO-247AC (JEDEC) K/W g HFA32PA120C For technical questions within your region, please contact one of the following: Document Number: 94073 [email protected], [email protected], [email protected] Revision: 23-May-11 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-HFA32PA120CPbF 1000 1000 IR - Reverse Current (µA) IF - Instantaneous Forward Current (A) HEXFRED® Vishay Semiconductors Ultrafast Soft Recovery Diode, 2 x 16 A 10 TJ = 150 °C TJ = 125 °C TJ = 25 °C 1 TJ = 150 °C 100 TJ = 125 °C 10 1 TJ = 25 °C 0.1 0.01 0.1 0 2 4 6 0 8 VFM - Forward Voltage Drop (V) 94073_01 200 600 800 1000 1200 VR - Reverse Voltage (V) 94073_02 Fig. 1 - Maximum Forward Voltage Drop vs. Instantaneous Forward Current 400 Fig. 2 - Typical Reverse Current vs. Reverse Voltage CT - Junction Capacitance (pF) 1000 100 TJ = 25 °C 10 1 0 10 100 1000 10 000 VR - Reverse Voltage (V) 94073_03 Fig. 3 - Typical Junction Capacitance vs. Reverse Voltage ZthJC - Thermal Response 1 0.1 Single pulse (thermal resistance) D = 0.50 D = 0.20 D = 0.10 D = 0.05 D = 0.02 D = 0.01 PDM t1 t2 Notes: 1. Duty factor D = t1/t2 2. Peak TJ = PDM x ZthJC + TC 0.01 0.00001 94073_04 0.0001 0.001 0.01 0.1 1 10 100 t1 - Rectangular Pulse Duration (s) Fig. 4 - Maximum Thermal Impedance ZthJC Characteristics Document Number: 94073 Revision: 23-May-11 For technical questions within your region, please contact one of the following: www.vishay.com [email protected], [email protected], [email protected] 3 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-HFA32PA120CPbF Vishay Semiconductors HEXFRED® Ultrafast Soft Recovery Diode, 2 x 16 A 270 1400 170 VR = 200 V TJ = 125 °C TJ = 25 °C 1200 IF = 16 A IF = 8 A Qrr (nC) trr (ns) 220 1600 VR = 200 V TJ = 125 °C TJ = 25 °C 120 IF = 16 A IF = 8 A 1000 800 600 400 70 200 20 100 0 100 1000 dIF/dt (A/µs) 94073_05 Fig. 5 - Typical Reverse Recovery Time vs. dIF/dt (Per Leg) Fig. 7 - Typical Stored Charge vs. dIF/dt (Per Leg) 30 10 000 VR = 200 V TJ = 125 °C TJ = 25 °C Irr (A) 20 dI(rec)M/dt (A/µs) 25 1000 dIF/dt (A/µs) 94073_07 IF = 16 A IF = 8 A 15 10 VR = 200 V TJ = 125 °C TJ = 25 °C 1000 IF = 16 A IF = 8 A 100 5 0 100 94073_06 1000 dIF/dt (A/µs) Fig. 6 - Typical Recovery Current vs. dIF/dt (Per Leg) www.vishay.com 4 10 100 94073_08 1000 dIF/dt (A/µs) Fig. 8 - Typical dI(rec)M/dt vs. dIF/dt (Per Leg) For technical questions within your region, please contact one of the following: Document Number: 94073 [email protected], [email protected], [email protected] Revision: 23-May-11 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-HFA32PA120CPbF HEXFRED® Vishay Semiconductors Ultrafast Soft Recovery Diode, 2 x 16 A VR = 200 V 0.01 Ω L = 70 μH D.U.T. dIF/dt adjust D IRFP250 G S Fig. 9 - Reverse Recovery Parameter Test Circuit (3) trr IF ta tb 0 Qrr (2) IRRM (4) 0.5 IRRM dI(rec)M/dt (5) 0.75 IRRM (1) dIF/dt (1) dIF/dt - rate of change of current through zero crossing (2) IRRM - peak reverse recovery current (3) trr - reverse recovery time measured from zero crossing point of negative going IF to point where a line passing through 0.75 IRRM and 0.50 IRRM extrapolated to zero current. (4) Qrr - area under curve defined by trr and IRRM Qrr = trr x IRRM 2 (5) dI(rec)M/dt - peak rate of change of current during tb portion of trr Fig. 10 - Reverse Recovery Waveform and Definitions Document Number: 94073 Revision: 23-May-11 For technical questions within your region, please contact one of the following: www.vishay.com [email protected], [email protected], [email protected] 5 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-HFA32PA120CPbF HEXFRED® Ultrafast Soft Recovery Diode, 2 x 16 A Vishay Semiconductors ORDERING INFORMATION TABLE Device code VS- HF A 32 PA 120 C PbF 1 2 3 4 5 6 7 8 1 - Vishay Semiconductors product 2 - HEXFRED® family 3 - Electron irradiated 4 - Current rating (32 = 32 A) 5 - PA = TO-247AC 6 - Voltage rating: (120 = 1200 V) 7 - Circuit configuration C = Common cathode 8 - PbF = Lead (Pb)-free LINKS TO RELATED DOCUMENTS Dimensions www.vishay.com/doc?95223 Part marking information www.vishay.com/doc?95226 www.vishay.com 6 For technical questions within your region, please contact one of the following: Document Number: 94073 [email protected], [email protected], [email protected] Revision: 23-May-11 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Outline Dimensions www.vishay.com Vishay Semiconductors DIMENSIONS in millimeters and inches A A (3) (6) Ø P E B (2) R/2 N A2 S (Datum B) Ø K M DBM FP1 A D2 Q 2xR (2) D1 (4) D 1 4 D 3 2 Thermal pad (5) L1 C L A See view B 2 x b2 3xb 0.10 M C A M Planting (4) E1 0.01 M D B M View A - A C 2x e A1 b4 (b1, b3, b5) Lead assignments Base metal D DE (c) c1 E C C Diodes 1. - Anode/open 2. - Cathode 3. - Anode (b, b2, b4) (4) Section C - C, D - D, E - E SYMBOL A A1 A2 b b1 b2 b3 b4 b5 c c1 D D1 MILLIMETERS MIN. MAX. 4.65 5.31 2.21 2.59 1.50 2.49 0.99 1.40 0.99 1.35 1.65 2.39 1.65 2.37 2.59 3.43 2.59 3.38 0.38 0.86 0.38 0.76 19.71 20.70 13.08 - INCHES MIN. MAX. 0.183 0.209 0.087 0.102 0.059 0.098 0.039 0.055 0.039 0.053 0.065 0.094 0.065 0.094 0.102 0.135 0.102 0.133 0.015 0.034 0.015 0.030 0.776 0.815 0.515 - View B NOTES SYMBOL 3 4 D2 E E1 e FK L L1 N P P1 Q R S MILLIMETERS MIN. MAX. 0.51 1.30 15.29 15.87 13.72 5.46 BSC 2.54 14.20 16.10 3.71 4.29 7.62 BSC 3.56 3.66 6.98 5.31 5.69 4.52 5.49 5.51 BSC INCHES MIN. MAX. 0.020 0.051 0.602 0.625 0.540 0.215 BSC 0.010 0.559 0.634 0.146 0.169 0.3 0.14 0.144 0.275 0.209 0.224 1.78 0.216 0.217 BSC NOTES 3 Notes (1) Dimensioning and tolerancing per ASME Y14.5M-1994 (2) Contour of slot optional (3) Dimension D and E do not include mold flash. Mold flash shall not exceed 0.127 mm (0.005") per side. These dimensions are measured at the outermost extremes of the plastic body (4) Thermal pad contour optional with dimensions D1 and E1 (5) Lead finish uncontrolled in L1 (6) Ø P to have a maximum draft angle of 1.5 to the top of the part with a maximum hole diameter of 3.91 mm (0.154") (7) Outline conforms to JEDEC outline TO-247 with exception of dimension c Revision: 16-Jun-11 Document Number: 95223 1 For technical questions within your region: [email protected], [email protected], [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 11-Mar-11 www.vishay.com 1