PTEA420025, PTEA420033 www.ti.com SLTS288C – JUNE 2007 – REVISED OCTOBER 2010 20-A, 48-V INPUT, ISOLATED, 1/8th BRICK DC-DC CONVERTER Check for Samples: PTEA420025, PTEA420033 FEATURES 1 • • • • • • • • • • • • • • DESCRIPTION 20–A Output Current Rating Input Voltage Range: 36 V to 75 V 92% Efficiency 1500 Vdc Isolation Fast Transient Response On/Off Control Overcurrent Protection Differential Remote Sense Adjustable Output Voltage Output Overvoltage Protection Over-Temperature Shutdown Undervoltage Lockout Standard 1/8-Brick Footprint UL Safety Agency Approval The PTEA series of power modules are single-output isolated DC/DC converters, housed in an industry standard 1/8thbrick package. These modules are rated up to 66 W with a maximum load current of 20 A. The PTEA series operates from a standard 48-V telecom central office (CO) supply and occupies only 2.0 in2 of PCB area. The modules offer OEMs a compact and flexible high-output power source in an industry standard footprint. They are suitable for distributed power applications in both telecom and computing environments, and may be used for powering high-end microprocessors, DSPs, general purpose logic and analog. Features include a remote On/Off control with optional logic polarity, an undervoltage lockout (UVLO), a differential remote sense, and an industry standard output voltage adjustment using an external resistor. Protection features include output overcurrent protection (OCP), overvoltage protection (OVP), and thermal shutdown (OTP). The modules are fully integrated for stand-alone operation, and require no additional components. STANDARD APPLICATION SENSE (+) +VO 7 +VI Sense(+) 1 +V I CI (Optional) 3 −VI +VO PTEA4200xxN −VI Remote On/Off 2 Adjust −VO Sense(−) 8 6 CO (Optional) 4 L O A D −VO 5 SENSE (–) 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2007–2010, Texas Instruments Incorporated PTEA420025, PTEA420033 SLTS288C – JUNE 2007 – REVISED OCTOBER 2010 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. ORDERING INFORMATION For the most current package and ordering information, see the Package Option Addendum at the end of this datasheet, or see the TI website at www.ti.com. Table 1. PART NUMBERING SCHEME Input Voltage PTEA Output Current 4 4 = 48 V Output Voltage 20 20 = 20 A Enable 033 Electrical Options N 025 = 2.5 V N = Negative 033 = 3.3 V P = Positive 2 Pin Style A 2 = VO Adjust D D = Through-hole, Pb-free ABSOLUTE MAXIMUM RATING UNIT TA VI, MAX PO, Operating Temperature Range Maximum Input Voltage Continuous voltage 80 V Peak voltage for 100 ms duration Maximum Output Power MAX TS –40°C to 85°C (1) Over VI Range 100 V PTEA420033x2 66 W PTEA420025x2 50 W Storage Temperature –55°C to 125°C Mechanical Shock Per Mil-STD-883, Method 2002.3 1 ms, 1/2 Sine, mounted AD Suffix 250 G Mechanical Vibrarion Per Mil-STD-883, Method 2007.2 20-2000 Hz, PCB mounted AD Suffix 15 G Weight Flammability (1) 2 18 grams Meets UL 94V-O See SOA curves or consult factory for appropriate derating. Submit Documentation Feedback Copyright © 2007–2010, Texas Instruments Incorporated Product Folder Link(s): PTEA420025 PTEA420033 PTEA420025, PTEA420033 www.ti.com SLTS288C – JUNE 2007 – REVISED OCTOBER 2010 ELECTRICAL CHARACTERISTICS PTEA420025 (Unless otherwise stated, TA =25°C, VI = 48 V, VO = 2.5 V, CO = 0 mF, and IO = IO(max)) PARAMETER PTEA420025 TEST CONDITIONS MIN IO Output Current Over VI range 0 VI Input Voltage Range Over IO Range 36 VO tol Set Point Voltage Tolerance TYP MAX 20 48 75 UNIT A V ±1 (1) %VO ±1.15 %VO Regtemp Temperature Variation –40°C >TA > 85°C Regline Line Regulation Over VI range ±5 mV Regload Load Regulation Over IO range ±5 mV ΔVotot Total Output Voltage Variation Includes set-point, line, load, –40°C >TA > 85°C ΔVADJ Output Adjust Range PO ≤ 75 W h Efficiency IO = 50% IO(max) VR VO Ripple (pk-pk) 20 MHz bandwidth ttr Transient Response ΔVtr ±1.5 –20 ±3 %VO 10 %VO 89% 50 0.1 A/ms slew rate, 50% to 75% IO(max) VO over/undershoot mVpp 150 ms 90 mV ITRIP Overcurrent Threshold Shutdown, followed by auto-recovery 28 A OVP Output Overvoltage Protection Output shutdown and latch off 120 %VO OTP Over Temperature Protection Temperature Measurement at thermal sensor. Hysteresis = 10°C nominal. 105 °C fs Switching Frequency Over VI range 290 kHz UVLO Undervoltage Lockout VOFF VI decreasing, IO = 6 A 29.4 VHYS Hysteresis 3.3 V On/Off Input: Negative Enable VIH Input High Voltage VIL Input Low Voltage IIL Input Low Current Referenced to –VI 2.4 Open (2) –0.2 0.8 –0.2 V mA On/Off Input: Positive Enable VIH Input High Voltage VIL Input Low Voltage IIL Input Low Current IISB Standby Input Current Output disabled (pin 2 status set to Off) CI External Input Capacitance Between +VI and –VI CO External Output Capacitance Between +VO and –VO Isolation Voltage Input-to-output and input-to-case Isolation Capacitance Input-to-output Isolation Resistance Input-to-output (1) (2) Referenced to –VI 2.4 Open (2) –0.2 0.8 V –0.2 mA 37 mA 100 0 mF 20000 1500 1200 10 mF Vdc pF MΩ If Sense(–) is not used, pin 5 must be connected to pin 4 for optimum output voltage accuracy. The Remote On/Off input has an internal pull-up and may be controlled with an open collector (drain) interface. An open circuit correlates to a logic high. Consult the application notes for interface considerations. Copyright © 2007–2010, Texas Instruments Incorporated Product Folder Link(s): PTEA420025 PTEA420033 Submit Documentation Feedback 3 PTEA420025, PTEA420033 SLTS288C – JUNE 2007 – REVISED OCTOBER 2010 www.ti.com ELECTRICAL CHARACTERISTICS PTEA420033 (Unless otherwise stated, TA =25°C, VI = 48 V, VO = 3.3 V, CO = 0 mF, and IO = IO(max)) PARAMETER PTEA420033 TEST CONDITIONS MIN IO Output Current Over VI range 0 VI Input Voltage Range Over IO Range 36 VO tol Set Point Voltage Tolerance TYP MAX 20 48 75 UNIT A V ±1 (1) %VO ±1.15 %VO Regtemp Temperature Variation –40°C >TA > 85°C Regline Line Regulation Over VI range ±5 mV Regload Load Regulation Over IO range ±5 mV ΔVotot Total Output Voltage Variation Includes set-point, line, load, –40°C >TA > 85°C ΔVADJ Output Adjust Range PO ≤ 100 W h Efficiency IO = 50% IO(max) VR VO Ripple (pk-pk) 20 MHz bandwidth ttr Transient Response ΔVtr ±1.5 –20 ±3 %VO 10 %VO 91% 50 0.1 A/ms slew rate, 50% to 75% IO(max) VO over/undershoot mVpp 150 ms 90 mV ITRIP Overcurrent Threshold Shutdown, followed by auto-recovery 28 A OVP Output Overvoltage Protection Output shutdown and latch off 120 %VO OTP Over Temperature Protection Temperature Measurement at thermal sensor. Hysteresis = 10°C nominal. 105 °C fs Switching Frequency Over VI range 290 kHz UVLO Undervoltage Lockout VOFF VI decreasing, IO = 6 A 29.4 VHYS Hysteresis 3.3 V On/Off Input: Negative Enable VIH Input High Voltage VIL Input Low Voltage IIL Input Low Current Referenced to –VI 2.4 Open (2) –0.2 0.8 –0.2 V mA On/Off Input: Positive Enable VIH Input High Voltage VIL Input Low Voltage IIL Input Low Current IIsb Standby Input Current Output disabled (pin 2 status set to Off) CI External Input Capacitance Between +VI and –VI CO External Output Capacitance Between +VO and –VO Isolation Voltage Input-to-output and input-to-case Isolation Capacitance Input-to-output Isolation Resistance Input-to-output (1) (2) 4 Referenced to –VI 2.4 Open (2) –0.2 0.8 V –0.2 mA 42 mA 100 0 mF 20000 1500 1200 10 mF Vdc pF MΩ If Sense(–) is not used, pin 5 must be connected to pin 4 for optimum output voltage accuracy. The Remote On/Off input has an internal pull-up and may be controlled with an open collector (drain) interface. An open circuit correlates to a logic high. Consult the application notes for interface considerations. Submit Documentation Feedback Copyright © 2007–2010, Texas Instruments Incorporated Product Folder Link(s): PTEA420025 PTEA420033 PTEA420025, PTEA420033 www.ti.com SLTS288C – JUNE 2007 – REVISED OCTOBER 2010 PIN DESCRIPTIONS +VI: The positive input for the module with respect to –VI. When powering the module from a –48-V telecom central office supply, this input is connected to the primary system ground. –VI: The negative input supply for the module, and the 0 VDC reference for the Remote On/Off input. When powering the module from a +48-V supply, this input is connected to the 48-V return. Remote On/Off: This input controls the On/Off status of the output voltage. It is either driven low (–VI potential), or left open-circuit. For units identified with the NEN option, applying a logic low to this pin will enable the output. And for units identified with the PEN option, the output will be disabled. VO Adjust: Allows the output voltage to be trimmed by up or down between +10% and –20% of its nominal value. The adjustment method uses a single external resistor. Connecting the resistor between VO Adjust and –VO adjusts the output voltage lower, and placing it between VO Adjust and +VO adjusts the output higher. The calculations for the resistance value follows industry standard formulas. For further information consult the application note on output voltage adustment. +VO: The positive power output with respect to –VO, which is DC isolated from the input supply pins. If a negative output voltage is desired, +VO should be connected to the secondary circuit common and the output taken from –VO. –VO: The negative power output with respect to +VO, which is DC isolated from the input supply pins. This output is normally connected to the secondary circuit common when a positive output voltage is desired. Sense(+): Provides the converter with an output sense capability to regulate the set-point voltage directly at the load. When used with Sense(-), the regulation circuitry will compensate for voltage drop between the converter and the load. The pin may be left open circuit, but connecting it to +VO will improve load regulation. Sense(–): Provides the converter with an output sense capability when used in conjunction with Sense(+) input. For optimum output voltage accuracy this pin should always be connected to –VO. PTEA4200xx (Top View) +VO 1 +VI Sense(+) 2 On/Off 3 −VI Adjust Sense(−) −VO 8 7 6 5 4 Copyright © 2007–2010, Texas Instruments Incorporated Product Folder Link(s): PTEA420025 PTEA420033 Submit Documentation Feedback 5 PTEA420025, PTEA420033 SLTS288C – JUNE 2007 – REVISED OCTOBER 2010 www.ti.com TYPICAL CHARACTERISTICS PTEA420025, VO = 2.5 V (1) (2) EFFICIENCY vs LOAD CURRENT OUTPUT RIPPLE vs LOAD CURRENT 12 95 VI (V) VO - Ouptut Voltage Ripple - VPP (mV) 90 85 60 V 80 75 75 V 70 VO = 2.5 V 65 VI (V) 60 36 48 60 75 55 5 10 15 IO - Output Current - A 60 V 75 V 8 6 48 V 4 7 6 60 V 5 4 75 V 3 VI (V) 2 2 36 V 1 VO = 2.5 V 0 20 VO = 2.5 V 8 36 48 60 75 10 36 V 0 50 0 9 48 V PDISS - Power Dissipation - W 36 V h - Efficiency - % POWER DISSIPATION vs LOAD CURRENT 5 10 15 IO - Output Current - A Figure 1. 20 48 V 0 0 Figure 2. 5 10 15 IO - Output Current - A 36 48 60 75 20 Figure 3. AMBIENT TEMPERATURE vs LOAD CURRENT 90 TA - Ambient Temperature - °C 80 70 400 LFM 200 LFM 60 VO = 2.5 V VI = 48 V 50 100 LFM Airflow 400 LFM 40 Natural Convection 200 LFM 30 100 LFM Nat conv 20 0 5 10 15 IO - Output Current - A 20 Figure 4. (1) (2) 6 All data listed in Figure 1, Figure 2, and Figure 3 have been developed from actual products tested at 25°C. This data is considered typical data for the dc-dc converter. The temperature derating curves represent operating conditions at which internal components are at or below manufacturer's maximum rated operating temperature. Derating limits apply to modules soldered directly to a 100–mm × 100–mm, double-sided PCB with 2 oz. copper. For surface mount packages, multiple vias (plated through holes) are required to add thermal paths around the power pins. Please refer to the mechanical specification for more information. Applies to Figure 4. Submit Documentation Feedback Copyright © 2007–2010, Texas Instruments Incorporated Product Folder Link(s): PTEA420025 PTEA420033 PTEA420025, PTEA420033 www.ti.com SLTS288C – JUNE 2007 – REVISED OCTOBER 2010 TYPICAL CHARACTERISTICS PTEA420033, VO = 3.3 V (1) (2) EFFICIENCY vs LOAD CURRENT OUTPUT RIPPLE vs LOAD CURRENT 12 48 V 36 V VO - Ouptut Voltage Ripple - VPP (mV) 85 75 V 80 60 V 75 70 VO = 3.3 V 65 VI (V) 60 36 48 60 75 55 5 10 15 IO - Output Current - A 10 60 V 8 6 48 V 4 VI (V) 36 V 36 48 60 75 2 0 20 5 10 15 IO - Output Current - A Figure 5. VO = 3.3 V 8 7 6 75 V 60 V 5 48 V 4 36 V 3 VI (V) 2 36 48 60 75 1 0 0 50 0 75 V VO = 3.3 V 90 PDISS - Power Dissipation - W 95 h - Efficiency - % POWER DISSIPATION vs LOAD CURRENT 20 0 Figure 6. 5 10 15 IO - Output Current - A 20 Figure 7. AMBIENT TEMPERATURE vs LOAD CURRENT 90 TA - Ambient Temperature - °C 80 70 400 LFM 60 200 LFM VO = 3.3 V VI = 48 V 50 100 LFM Airflow 400 LFM 40 Natural Convection 200 LFM 30 100 LFM Nat conv 20 0 5 10 15 IO - Output Current - A 20 Figure 8. (1) (2) All data listed in Figure 5, Figure 6, and Figure 7 have been developed from actual products tested at 25°C. This data is considered typical data for the dc-dc converter. The temperature derating curves represent operating conditions at which internal components are at or below manufacturer's maximum rated operating temperature. Derating limits apply to modules soldered directly to a 100–mm × 100–mm, double-sided PCB with 2 oz. copper. For surface mount packages, multiple vias (plated through holes) are required to add thermal paths around the power pins. Please refer to the mechanical specification for more information. Applies to Figure 8. Copyright © 2007–2010, Texas Instruments Incorporated Product Folder Link(s): PTEA420025 PTEA420033 Submit Documentation Feedback 7 PTEA420025, PTEA420033 SLTS288C – JUNE 2007 – REVISED OCTOBER 2010 www.ti.com APPLICATION INFORMATION Operating Features and System Considerations for the PTEA Series of DC/DC Converters Overcurrent Protection To protect against load faults, these converters incorporate output overcurrent protection. Applying a load to the output that exceeds the converter's overcurrent threshold (see applicable specification) will cause the output voltage to momentarily fold back, and then shut down. Following shutdown the module will periodically attempt to automatically recover by initiating a soft-start power-up. This is often described as a hiccup mode of operation, whereby the module continues in the cycle of successive shutdown and power up until the load fault is removed. Once the fault is removed, the converter automatically recovers and returns to normal operation. Output Overvoltage Protection Each converter incorporates protection circuitry that continually senses for an output overvoltage (OV) condition. The OV threshold is set approximately 20% higher than the nominal output voltage. If the converter output voltage exceeds this threshold, the converter is immediately shut down and remains in a latched-off state. To resume normal operation the converter must be actively reset. This can only be done by momentarily removing the input power to the converter. For fail-safe operation and redundancy, the OV protection uses circuitry that is independent of the converter’s internal feedback loop. Overtemperature Protection Overtemperature protection is provided by an internal temperature sensor, which closely monitors the temperature of the converter’s printed circuit board (PCB). If the sensor exceeds a temperature of approximately 105°C, the converter will shut down. The converter will then automatically restart when the sensed temperature drops back to approximately 95°C. When operated outside its recommended thermal derating envelope (see data sheet SOA curves), the converter will typcially cycle on and off at intervals from a few seconds to one or two minutes. This is to ensure that the internal components are not permanently damaged from excessive thermal stress. Undervoltage Lockout The Undervoltage lockout (UVLO) is designed to prevent the operation of the converter until the input voltage is at the minimum input voltage. This prevents high start-up current during normal power-up of the converter, and minimizes the current drain from the input source during low input voltage conditions. The UVLO circuitry also overrides the operation of the Remote On/Off control. Primary-Secondary Isolation These converters incorporate electrical isolation between the input terminals (primary) and the output terminals (secondary). All converters are production tested to a withstand voltage of 1500 VDC. This specification complies with UL60950 and EN60950 requirements. This allows the converter to be configured for either a positive or negative input voltage source. The data sheet Pin Descriptions section provides guidance as to the correct reference that must be used for the external control signals. Input Current Limiting The converter is not internally fused. For safety and overall system protection, the maximum input current to the converter must be limited. Active or passive current limiting can be used. Passive current limiting can be a fast acting fuse. A 125-V fuse, rated no more than 10 A, is recommended. Active current limiting can be implemented with a current limited Hot-Swap controller. Thermal Considerations Airflow may be necessary to ensure that the module can supply the desired load current in environments with elevated ambient temperatures. The required airflow rate may be determined from the Safe Operating Area (SOA) thermal derating chart (see typical characteristics). 8 Submit Documentation Feedback Copyright © 2007–2010, Texas Instruments Incorporated Product Folder Link(s): PTEA420025 PTEA420033 PTEA420025, PTEA420033 www.ti.com SLTS288C – JUNE 2007 – REVISED OCTOBER 2010 Differential Remote Sense The remote sense pins allows the converter to precisely regulate the DC output voltage at a remote location. This might be a power plane on an inner layer of the host PCB. Connecting Sense(+) directly to +VO , and Sense(–) to –VO will improve output voltage accuracy. In the event that the sense pins are left open-circuit, an internal 100-Ω (S+) or 10-Ω (S–) resistor between each sense pin and its corresponding output prevents an excessive rise in the output voltage. For practical reasons, the amount of IR voltage compensation should be limited to 0.5 V maximum. The remote sense feature is designed to compensate for limited amounts of IR voltage drop. It is not intended to compensate for the forward drop of a non-linear or frequency dependent components that may be placed in series with the converter output. Examples of such components include OR-ing diodes, filter inductors, ferrite beads, and fuses. Enclosing these components with the remote sense connections effectively places them inside the regulation control loop, which can affect the stability of the regulator. Using the Remote On/Off Function on the PTEA Series of DC/DC Converters For applications requiring output voltage On/Off control, the PTEA series of DC/DC converters incorporate a Remote On/Off control (pin 2). This feature can be used to switch the module off without removing the applied input source voltage. When placed in the Off state, the standby current drawn from the input source is typically reduced to 3 mA. Negative Output Enable (NEN) Models using the negative enable option, the Remote On/Off (pin 2) control must be driven to a logic low voltage for the converter to produce an output. This is accomplished by either permanently connecting pin 2 to –VI (pin 3), or driving it low with an external control signal. Table 2 shows the input requirements of pin 2 for those modules with the NEN option. Table 2. On/Off Control Requirements for Negative Enable PARAMETER MIN TYP MAX VIH Disable 2.4 V 20 V VIL Enable –0.2 V 0.8 V Vo/c Open-Circuit II Pin 2 at –VI 3.3 V 4V –0.2 mA Positive Output Enable (PEN) For those models with the positive enable (PEN) option, leaving pin 2 open circuit, (or driving it to an equivalent logic high voltage), will enable the converter output. This allows the module to produce an output voltage whenever a valid input source voltage is applied to +VI with respect to –VI. If a logic-low signal is then applied to pin 2 the converter output is disabled. Table 3 gives the input requirements of pin 2 for modules with the PEN option. Table 3. On/Off Control Requirements for Positive Enable PARAMETER MIN VIH Enable 4.5 V VIL Disable –0.2 V Vo/c Open-Circuit II Pin 2 at –VI TYP MAX 20 V 0.8 V 3.3 V 4V –0.2 mA Copyright © 2007–2010, Texas Instruments Incorporated Product Folder Link(s): PTEA420025 PTEA420033 Submit Documentation Feedback 9 PTEA420025, PTEA420033 SLTS288C – JUNE 2007 – REVISED OCTOBER 2010 www.ti.com Notes: 1. The Remote On/Off control uses –VI (pin 3) as its ground reference. All voltages are with respect to –VI. 2. An open-collector device (preferably a discrete transistor) is recommended. A pull-up resistor is not required. If one is added the pull-up voltage should not exceed 20 V. Caution: Do not use a pull-resistor to +VI (pin 1). The remote On/Off control has a maximum input voltage of 20 V. Exceeding this voltage will overstress, and possibly damage, the converter. 3. The Remote On/Off pin may be controlled with devices that have a totem-pole output. This is provided the output high level voltage (VOH) meets the module's minimum VIH specified in Table 2. If a TTL gate is used, a pull-up resistor may be required to the logic supply voltage. 4. The converter incorporates an undervoltage lockout (UVLO). The UVLO keeps the converter off until the input voltage is close to the minimum specified operating voltage. This is regardless of the state of the Remote On/Off control. Consult the product specification for the UVLO input voltage thresholds. PTEA4200xx Q1 BSS138 2 Remote On/Off 1 = Disable −VI 3 −VI Figure 9. Recommended Control or Remote On/Off Input Turn-On: With a valid input source voltage applied, the converter produces a regulated output voltage within 75 ms of the output being enabled. Figure 10 shows the output response of the PTEA420033P following the removal of the logic-low signal from the Remote On/Off (pin 2); see Figure 9. This corresponds to the drop in Q1 VGS in Figure 10. Although the rise-time of the output voltage is short (<10 ms), the indicated delay time will vary depending upon the input voltage and the module’s internal timing. The waveforms were measured with 48 VDC input voltage, and a 10-A resistive load. Turn-Off Time: When a valid input source is removed or if the Remote On/Off (pin 2) is used to disable the output, with no external output capacitance, the module powers down within 200 ms. Figure 11 shows that, during power down, there is no output voltage undershoot. If used to supply processor I/O voltages, the lack of undershoot ensures the parasitic diodes do not conduct current and potentially cause damage to external circuitry. 10 Submit Documentation Feedback Copyright © 2007–2010, Texas Instruments Incorporated Product Folder Link(s): PTEA420025 PTEA420033 PTEA420025, PTEA420033 www.ti.com SLTS288C – JUNE 2007 – REVISED OCTOBER 2010 VO (1 V/div) VO (1 V/div) II (500 mA/div) II (500 mA/div) Q1 VDS (5V/div) Q1 VDS (5V/div) t − Time − 4 ms/div t − Time − 1 ms/div Figure 10. Power Up Figure 11. Power Down Adjusting the Output Voltage of the 20–A Rated PTEA Series of Isolated DC/DC Converters The output voltage adjustment of the PTEA series of isolated DC/DC converters follows the standard adopted by popular 1/8-brick DC/DC converters. Adjustment is accomplished with a single external resistor that can adjust the output voltage from –20% to +10% of the nominal set-point voltage. The placement of the resistor determines the direction of adjustment, up or down, and the value of the magnitude of adjustment. Adjust Up: To increase the output voltage add a resistor, R1, between VO Adjust (pin 6) and Sense(+) (pin 7). Adjust Down: Add a resistor, (R2), between VO Adjust (pin 6) and Sense(–) (pin 5). Refer to Figure 12 for the placement of the required resistor, R1 or (R2). Sense (+) 7 Sense(+) 1 +V I +VO PTEA4200xx 3 8 6 −VO 4 2 CO 330 µF Adjust −VI Remote On/Off R1 Adjust Up Sense(–) + +VI −VI +VO (R2) Adjust Down L O A D −VO 5 Sense (–) Figure 12. The values of R1 [adjust up], and (R2) [adjust down], can be calculated using the following formulas. R1 = 5.11 VO (100 + D% ) 511 - 10.22 (kW ) 1.224 D% D% (1) (R2 ) = 5.11 æç 100 ö ÷ - 10.22 (k W ) è D% ø (2) Where: Δ% = Amount of adjustment in % Copyright © 2007–2010, Texas Instruments Incorporated Product Folder Link(s): PTEA420025 PTEA420033 Submit Documentation Feedback 11 PTEA420025, PTEA420033 SLTS288C – JUNE 2007 – REVISED OCTOBER 2010 www.ti.com VO = Original set-point voltage Notes: 1. Use only a single 1% resistor in either the R1 or (R2) location. Place the resistor as close to the converter as possible. 2. If the output voltage is increased, the maximum load current must be derated according to the following equation. IO(max) = VO ´ IO(rated) VA (3) Where: VO = Original set-point voltage VA = Adjusted output voltage (measured between pins 8 and 4) In any instance, the load current must not exceed the converter's maximum rated output current of 20 A. 3. The overvoltage threshold is fixed, and is set approximately 20% above the nominal output voltage. Adjusting the output voltage higher reduces the voltage margin between the adjusted output voltage and the overvoltage (OV) protection threshold. This could make the module sensitive to OV fault detection, as a result of random noise and load transients. 12 Submit Documentation Feedback Copyright © 2007–2010, Texas Instruments Incorporated Product Folder Link(s): PTEA420025 PTEA420033 PTEA420025, PTEA420033 www.ti.com SLTS288C – JUNE 2007 – REVISED OCTOBER 2010 Table 4. Adjustment Resistor Values Adjusted Output Voltage (V) Trim-Up RADJ Trim-Down RADJ VO (nom) % Adjust (V) 3.3 V 2.5 V 3.3 V R1 (kΩ) 2.5 V R1 (kΩ) 3.3 V R2 (kΩ) 2.5 V R2 (kΩ) +10 3.630 2.750 90.9 53.6 - - +9 3.597 2.725 100 59.0 - - +8 3.564 2.700 113 66.5 - - +7 3.531 2.675 127 76.8 - - +6 3.498 2.650 147 88.7 - - +5 3.465 2.625 178 107 - - +4 3.432 2.600 221 133 - - +3 3.399 2.575 294 178 - - +2 3.366 2.550 432 267 - - +1 3.333 2.525 866 536 - - 0 3.300 2.500 Open Open - - –1 3.267 2.475 - - 499 499 –2 3.234 2.450 - - 243 243 –3 3.201 2.425 - - 158 158 –4 3.168 2.400 - - 118 118 –5 3.135 2.375 - - 90.9 90.9 –6 3.102 2.350 - - 75 75 –7 3.069 2.325 - - 63.4 63.4 –8 3.036 2.300 - - 53.6 53.6 –9 3.003 2.275 - - 46.4 46.4 –10 2.970 2.250 - - 41.2 41.2 –11 2.937 2.225 - - 36.5 36.5 –12 2.904 2.200 - - 32.4 32.4 –13 2.871 2.175 - - 28.7 28.7 –14 2.838 2.150 - - 26.1 26.1 –15 2.805 2.125 - - 23.7 23.7 –16 2.772 2.100 - - 21.5 21.5 –17 2.739 2.075 - - 19.6 19.6 –18 2.706 2.050 - - 18.2 18.2 –19 2.673 2.025 - - 16.5 16.5 –20 2.640 2.000 - - 15.4 15.4 Copyright © 2007–2010, Texas Instruments Incorporated Product Folder Link(s): PTEA420025 PTEA420033 Submit Documentation Feedback 13 PACKAGE OPTION ADDENDUM www.ti.com 13-Nov-2010 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) PTEA420025N2AD ACTIVE ThroughHole Module EAW 8 15 Pb-Free (RoHS) SN N / A for Pkg Type Request Free Samples PTEA420025P2AD ACTIVE ThroughHole Module EAW 8 15 Pb-Free (RoHS) SN N / A for Pkg Type Request Free Samples PTEA420033N2AD ACTIVE ThroughHole Module EAW 8 15 Pb-Free (RoHS) SN N / A for Pkg Type Request Free Samples PTEA420033P2AD ACTIVE ThroughHole Module EAW 8 15 Pb-Free (RoHS) SN N / A for Pkg Type Request Free Samples (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DLP® Products www.dlp.com Communications and Telecom www.ti.com/communications DSP dsp.ti.com Computers and Peripherals www.ti.com/computers Clocks and Timers www.ti.com/clocks Consumer Electronics www.ti.com/consumer-apps Interface interface.ti.com Energy www.ti.com/energy Logic logic.ti.com Industrial www.ti.com/industrial Power Mgmt power.ti.com Medical www.ti.com/medical Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Space, Avionics & Defense www.ti.com/space-avionics-defense RF/IF and ZigBee® Solutions www.ti.com/lprf Video and Imaging www.ti.com/video Wireless www.ti.com/wireless-apps Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2010, Texas Instruments Incorporated