Alternative Device Available SFH618A, SFH6186 www.vishay.com Vishay Semiconductors Optocoupler, Phototransistor Output, Low Input Current FEATURES A 1 4 C C 2 3 E • Good CTR linearity depending on forward current • Low CTR degradation • High collector emitter voltage, VCEO = 55 V • Isolation test voltage, 5300 VRMS • Low coupling capacitance • End stackable, 0.100" (2.54 mm) spacing • High common mode transient immunity • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 1 APPLICATIONS 1 i179061-1 • • • • DESCRIPTION The SFH618A (DIP) and SFH6186 (SMD) feature a high current transfer ratio, low coupling capacitance and high isolation voltage. These couplers have a GaAs infrared diode emitter, which is optically coupled to silicon planar phototransistor detector, and is incorporated in a plastic DIP-4 or SMD package. The coupling devices are designed for signal transmission between two electrically separated circuits.The couplers are end-stackable with 2.54 mm lead spacing. Creepage and clearance distances of > 8 mm achieved with option 6. Telecom Industrial controls Battery powered equipment Office machines AGENCY APPROVALS • UL1577, file no. E52744 system code H or J, double protection • CSA 93751 • DIN EN 60747-5-5 (VDE 0884-5) available with option 1 • BSI IEC 60950; IEC 60065 • FIMKO ORDERING INFORMATION S F H 6 1 8 # - PART NUMBER # X CTR BIN 0 # # PACKAGE OPTION DIP-# Option 6 7.62 mm 10.16 mm Option 7 Option 9 T TAPE AND REEL > 0.7 mm AGENCY CERTIFIED/PACKAGE UL, CUL DIP-4 DIP-4, 400 mil, option 6 SMD-4, option 7 SMD-4, option 9 VDE, UL, CUL DIP-4 DIP-4, 400 mil, option 6 SMD-4, option 7 SMD-4, option 9 > 0.1 mm CTR (%) 1 mA 63 to 125 SFH618A-2 SFH6186-2T (1) 100 to 200 SFH618A-3 SFH618A-3X006 SFH6186-3T (1), SFH6186-3T1 (2), SFH6186-3X002T (1) 160 to 320 SFH618A-4 - 250 to 500 SFH618A-5 SFH618A-5X007T (1) SFH6186-4T (1) SFH6186-5T (1), SFH6186-5T1 (2) 63 to 125 100 to 200 160 to 320 250 to 500 - SFH618A-3X001 SFH618A-3X016 SFH618A-3X017T (1) SFH6186-3X001T (1) SFH618A-4X001 SFH618A-4X016 SFH6186-4X001T SFH618A-5X016 SFH618A-5X017T (1) SFH6186-5X001T (1) Notes • Additional options may be possible, please contact sales office (1) Also available in tubes, do not put T to the end (2) Product is rotated 180° in tape and reel cavity Rev. 2.4, 23-May-13 Document Number: 83673 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Alternative Device Available SFH618A, SFH6186 www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL VALUE UNIT INPUT Reverse voltage VR 6 V Pdiss 70 mW IF 60 mA Collector emitter voltage VCEO 55 V Emitter collector voltage VECO 7 V Power dissipation Forward current OUTPUT IC 50 mA IC 100 mA Pdiss 150 mW t=1s VISO 5300 VRMS VIO = 500 V, Tamb = 25 °C RIO 1012 VIO = 500 V, Tamb = 100 °C RIO 1011 Storage temperature range Tstg - 55 to + 150 °C Ambient temperature range Tamb - 55 to + 100 °C Tj 125 °C Tsld 260 °C Collector current tp 1 ms Power dissipation COUPLER Isolation test voltage between emitter and detector Isolation resistance Junction temperature max. 10 s, dip soldering distance to seating plane 1.5 mm Soldering temperature (1) Notes • Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. (1) Refer to reflow profile for soldering conditions for surface mounted devices (SMD). Refer to wave profile for soldering conditions for through hole devices (DIP). Ptot - Power Dissipation (mW) 200 150 Detector 100 LED 50 0 0 20 40 60 80 100 120 Tamb - Ambient Temperature (°C) Fig. 1 - Permissible Power Dissipation vs. Ambient Temperature Rev. 2.4, 23-May-13 Document Number: 83673 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Alternative Device Available SFH618A, SFH6186 www.vishay.com Vishay Semiconductors ELECTRICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION PART SYMBOL MIN. TYP. MAX. UNIT INPUT Forward voltage IF = 5 mA VF 1.1 1.5 V Reverse current VR = 6 V IR 0.01 10 μA Capacitance VR = 0 V, f = 1 MHz CO 25 pF Rthja 1070 K/W VCE = 10 V ICEO 10 VCE = 5 V, f = 1 MHz CCE 7 pF Rthja 500 K/W SFH618A-2 VCEsat 0.25 0.4 V SFH6186-2 VCEsat 0.25 0.4 V SFH618A-3 VCEsat 0.25 0.4 V SFH6186-3 VCEsat 0.25 0.4 V SFH618A-4 VCEsat 0.25 0.4 V SFH6186-4 VCEsat 0.25 0.4 V SFH618A-5 VCEsat 0.25 0.4 V SFH6186-5 VCEsat 0.25 0.4 CC 0.25 Thermal resistance OUTPUT Collector emitter leakage current Collector emitter capacitance Thermal resistance 200 nA COUPLER IC = 0.32 mA, IF = 1 mA Collector emitter saturation voltage IC = 0.5 mA, IF = 1 mA IC = 0.8 mA, IF = 1 mA IC = 1.25 mA, IF = 1 mA Coupling capacitance V pF Note • Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements. CURRENT TRANSFER RATIO (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION IF = 1 mA, VCE = 0.5 V IF = 0.5 mA, VCE = 1.5 V IF = 1 mA, VCE = 0.5 V IF = 0.5 mA, VCE = 1.5 V IC/IF IF = 1 mA, VCE = 0.5 V IF = 0.5 mA, VCE = 1.5 V IF = 1 mA, VCE = 0.5 V IF = 0.5 mA, VCE = 1.5 V PART SYMBOL MIN. SFH618A-2 CTR 63 TYP. MAX. UNIT 125 % 125 % SFH6186-2 CTR 63 SFH618A-2 CTR 32 75 % SFH6186-2 CTR 32 75 % SFH618A-3 CTR 100 200 % SFH6186-3 CTR 100 200 % SFH618A-3 CTR 50 120 % SFH6186-3 CTR 50 120 % SFH618A-4 CTR 160 320 % 320 % SFH6186-4 CTR 160 SFH618A-4 CTR 80 200 % SFH6186-4 CTR 80 200 % SFH618A-5 CTR 250 500 % SFH6186-5 CTR 250 500 % SFH618A-5 CTR 125 300 % SFH6186-5 CTR 125 300 % SWITCHING CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER Turn on time Rise time Turn off time Fall time Rev. 2.4, 23-May-13 TEST CONDITION VCC = 5 V, IC = 2 mA, RL = 100 VCC = 5 V, IC = 2 mA, RL = 100 VCC = 5 V, IC = 2 mA, RL = 100 VCC = 5 V, IC = 2 mA, RL = 100 SYMBOL ton tr toff tf MIN. TYP. 6 3.5 5.5 5 MAX. UNIT μs μs μs μs Document Number: 83673 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Alternative Device Available SFH618A, SFH6186 www.vishay.com Vishay Semiconductors VCC = 5 V Input Input pulse RL 10 % VOUT Output pulse 90 % tr tf t off t on isfh618a_10 isfh618a_12 Fig. 2 - Test Circuit Fig. 3 - Test Circuit and Waveforms SAFETY AND INSULATION RATINGS PARAMETER TEST CONDITION SYMBOL MIN. Climatic classification (according to IEC68 part 1) TYP. MAX. UNIT 55/100/21 Comparative tracking index CTI 175 VIOTM 10000 VIORM 890 399 V V PSO 400 mW ISI 275 mA TSI 175 °C Creepage distance Standard DIP-4 7 mm Clearance distance Standard DIP-4 7 mm Creepage distance 400 mil DIP-4 8 mm Clearance distance 400 mil DIP-4 8 mm per IEC60950 2.10.5.1 0.4 mm Insulation thickness, reinforced rated Note • As per IEC60747-5-5, § 7.4.3.8.2, this optocoupler is suitable for “safe electrical insulation” only within the safety ratings. Compliance with the safety ratings shall be ensured by means of protective circuits. TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) 280 280 VCE = 0.5 V, CTR = f (TA) 240 200 CTR (%) CTR (%) 240 IF = 5mA 160 120 IF = 2mA 80 IF = 1mA 40 IF = 0.5mA 0 - 40 - 20 isfh618a_01 0 20 40 60 TA (°C) 80 100 Fig. 4 - Current Transfer Ratio (typ.) Rev. 2.4, 23-May-13 200 IF = 5mA 160 120 IF = 2mA 80 IF = 1mA 40 IF = 0.5mA 0 - 40 - 20 isfh618a_02 0 20 40 60 TA (°C) 80 100 Fig. 5 - Current Transfer Ratio (typ.) Document Number: 83673 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Alternative Device Available SFH618A, SFH6186 www.vishay.com Vishay Semiconductors 1.2 12 TA = 25 ºC, VF = f (IF) 10 ICE (mA) VR (V) 1.15 1.1 1.05 8 6 1 4 IF = 2 mA 0.95 2 IF = 1 mA 0.9 10-1 100 IF (mA) isfh618a_03 0 10-2 101 10-1 100 VCE (V) 101 102 Fig. 9 - Output Characteristics 1.2 103 IF = 1.0 mA, VF = f (TA) 1.15 IF = 0.5 mA isfh618a_06 Fig. 6 - Diode Forward Voltage (typ.) t off 1.1 t (µs) VF (V) IF = 5 mA TA = 25 ºC, CE = f (VCE, IF) 1.05 1 tF 102 t on tR 101 0.95 0 - 40 - 20 0 20 isfh618a_04 40 60 TA (°C) 80 100 100 102 isfh618a_09 Fig. 7 - Diode Forward Voltage (typ.) TA = 25 ºC, IF = 1.0 mA, VCC = 5.0 V, tON, tR, tOFF, tF, = f (RL) 103 104 RL (Ω) 105 Fig. 10 - Switching Times (typ.) 20 TA = 25 ºC, f = 1.0 MHz CEE = f (VCE) CCE (pF) 16 12 8 4 0 10-2 10-1 isfh618a_05 100 101 VCE (V) 102 Fig. 8 - Transistor Capacitance Rev. 2.4, 23-May-13 Document Number: 83673 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Alternative Device Available SFH618A, SFH6186 www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 2 1 Pin one ID 6.48 6.81 ISO method A 3 4 4.55 4.83 7.62 typ. 0.79 typ. 0.76 1.14 1.27 typ. 3.30 3.81 2.79 3.30 0.508 0.89 0.46 0.56 i178027 5.84 6.35 10° 4° typ. 0° to 15° 0.2 0.3 1.27 2.54 SMD 0.76 Pin one ID R 0.25 2.54 1.78 6.48 6.81 1.52 8 min. 11.05 3 4 9.52 10.03 4.55 4.83 0.76 1.14 7.52 7.90 0.79 typ. 10° 3.30 3.81 0.25 typ. ISO method A 8 min. 0.249 0.102 4° typ. 2.54 typ. Lead coplanarity 0.004 max. 1.27 typ. i178029 Option 6 Option 7 10.36 9.96 7.8 7.4 3° to 7° 0.508 1.020 Option 9 or SFH6186 9.53 10.03 7.62 ref. 7.62 typ. 4.6 4.1 0.102 0.249 0.30 typ. 0.7 8 min. 10.16 10.92 0.51 1.02 8.4 min. 10.3 max. 0.35 0.25 15° max. 0.76 2.54 R0.25 0.76 2.54 R0.25 1.78 18450-11 8 min. 11.05 1.52 1.78 8 min. 11.05 1.52 PACKAGE MARKING YWW 68 SFH618A-3 V Rev. 2.4, 23-May-13 Document Number: 83673 6 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000