MAXIM MAX7049ATI

19-5867; Rev 0; 6/11
EVALUATION KIT AVAILABLE
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
General Description
The MAX7049 high-performance, single-chip, ultralow-power ASK /FSK UHF transmitter operates in the
industrial, scientific, medical (ISM) band at 288MHz to
945MHz carrier frequencies. The IC also includes a low
phase noise fractional-N synthesizer for precise tuning,
fast frequency agility, and low out-of-band power. To
support narrow-band applications, the IC has both
amplitude-shaping and frequency-shaping functions that
enable the user to optimize spectral efficiency. The IC
offers Tx power up to +15dBm. These features make the
transmitter ideally suited for long-range applications.
Additional system-level features of the IC include a digital
temperature sensor and a number of flexible GPOs for
monitoring radio status and for the control of external
functions. A complete transmitter system can be built
using a low-end microprocessor control unit (MCU), the
IC, a crystal, and a small number of passive components.
The IC is available in a small, 5mm x 5mm, 28-pin TQFN
package with an exposed pad. It is specified to operate
in the -40°C to +125°C automotive temperature range.
Applications
Automatic Meter Reading (AMR)
RF Modules
Benefits and Features
STransmitter (Tx)
Provides Long Transmit Range Up to +15dBm

21mA Tx Current for +10dBm Tx Power*

41mA Tx Current for +15dBm Tx Power*

Modulation Shaping, ASK, FSK
SGeneral
Delivers Long Battery Life
< 50nA Shutdown Current
< 350nA Sleep Current

Minimizes the Number of I/Os Required
Between the IC and the MCU Serial Peripheral
Interface (SPI™)
Regulatory Compliant
FCC Part 15 Frequency Hopping
ETSI EN300-220 Compatible
On-Chip Temperature Sensor
Fast Fractional-N Synthesizer with a
User-Defined External Loop Filter
*VDD = 3.0V. Includes losses for the matching network and
regulatory-compliant harmonic filter.
Ordering Information appears at end of data sheet.
Long-Range, One-Way Remote Keyless Entry (RKE)
Wireless Sensor Networks
TPMS
For related parts and recommended products to use with this part,
refer to www.maxim-ic.com/MAX7049.related.
Home Security
Home Automation
RFID
Remote Controls
SPI is a trademark of Motorola, Inc.
�� Maxim Integrated Products 1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
TABLE OF CONTENTS
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
DC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
AC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Typical Operating Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Functional Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Detailed Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Architectural Overview and Applications Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Digital Inputs and Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Digital Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Digital Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Serial Peripheral Interface (SPI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
SPI Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Operating Mode Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Sleep Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Temperature Sensor Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Tx Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Frequency-Hopping Spread-Spectrum (FHSS) Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Functional Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Crystal Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Fractional-N Synthesizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Tx ASK Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Tx FSK Mode Using Frequency Waveshaping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Tx Pulse FSK Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Loop Bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Lock Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Power Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Tx ASK Mode Using Amplitude Waveshaping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Tx FSK Mode Amplitude Ramp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Register Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Detailed Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Layout Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Chip Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Package Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
�� Maxim Integrated Products 2
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
LIST OF FIGURES
Figure 1. SPI Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Figure 2. Typical Operating Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 3. Digital Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 4. Digital Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 5. Digital Output Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 6. SPI Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 7. SPI Write Command Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 8. SPI Read Command Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 9. SPI Read-All Command Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 10. SPI Reset Command Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 11. Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 12. Tx Warmup Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 13. Frequency-Hopping Spread-Spectrum (FHSS) Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 14. Recommended Crystal Connection to the IC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Figure 15. Fractional-N Synthesizer Configuration Tx ASK Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 16. Tx FSK Mode Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Figure 17. Tx FSK Frequency Waveshaping Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Figure 18. Synthesizer Loop Filter Topology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 19. Lock Detector Delay Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 20. Power Amplifier Topology and Optimum Signal Swings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 21. Tx ASK Mode Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 22. ASK Waveshaping Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 23. Tx FSK Amplitude Ramp Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Figure 24. Tx FSK Amplitude Ramp Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
LIST OF TABLES
Table 1. Optional Digital Input Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Table 2. Mode Control Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Table 3. Mode Option Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Table 4. Sleep Mode Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Table 5. Temperature Sensor Mode Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Table 6. Crystal Divider Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Table 7. LO Frequency-Divider Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Table 8. Tx FSK Pulse Mode Frequency Multiplier Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Table 9. PA Design Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
�� Maxim Integrated Products 3
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
LIST OF TABLES (continued)
Table 10. Configuration Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Table 11. Group 0: Identification Register (Ident) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Table 12. Ident Register (0x00) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Table 13. Group 1: General Configuration Registers (Conf0, Conf1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Table 14. Conf0 Register (0x01) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Table 15. Conf1 Register (0x02) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Table 16. Group 2: GPO, Data Output, and Clock Output Registers (IOConf0, IOConf1, IOConf2) . . . . . . . . . . . . . . 38
Table 17. IOConf0 Register (0x03) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Table 18. Register IOConf1 (0x04) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Table 19. Register IOConf2 (0x05) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Table 20. Group 3: Synthesizer Frequency Settings (FBase0, FBase1, FBase2, FLoad) . . . . . . . . . . . . . . . . . . . . . . . 41
Table 21. Synthesizer Divider Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Table 22. Synthesizer Programming Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Table 23. Frequency Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Table 24. FBase0 Register (0x08) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Table 25. FBase1 Register (0x09) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Table 26. FBase2 Register (0x0A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Table 27. FLoad (0x0B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Table 28. Group 4: Transmiter Amplitude and Timing Parameters (TxConf0, TxConf1, TxTstep) . . . . . . . . . . . . . . . . . 43
Table 29. TxConf0 Register (0x0C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Table 30. TxConf1 Register (0x0D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Table 31. TxTstep Register (0x0E) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Table 32. Group 5: Transmitter Shaping Registers (Shape00–Shape18) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Table 33. Shape00 Register (0x0F) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Table 34. Shape01–Shape18 Registers (0x10–0x21) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Table 35. Group 6: Control Registers (TestMux, Datain, EnableReg) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Table 36. TestMux Register (0x3C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Table 37. Datain Register (0x3D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Table 38. EnableReg Register (0x3E) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Table 39. Group 7: Read-Only Status Registers (TestBus0, TestBus1, Status0, Status1) . . . . . . . . . . . . . . . . . . . . . . . 46
Table 40. TestBus0 Register (0x40) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Table 41. Test Bus Signals (tbus[15:8]) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Table 42. TestBus1 Register (0x41) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Table 43. Test Bus Signals (tbus[7:0]) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Table 44. Status0 Register (0x42) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Table 45. Status1 Register (0x43) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
�� Maxim Integrated Products 4
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
ABSOLUTE MAXIMUM RATINGS
PAVDD, LOVDD, VCOVDD, CPVDD, PLLVDD,
XOVDD, DVDD, and AVDD to EP.....................-0.3V to +3.6V
ENABLE, DATAIN, SDI, SDO, CS, SCLK,
GPO1, GPO2, HOP, and SHDN to EP.. -0.3V to (VDD + 0.3V)
All Other Pins to EP................................... -0.3V to (VDD + 0.3V)
Continuous Power Dissipation (TA = +70NC)
TQFN (single-layer board)
(derate 21.3mW/NC above +70NC)..........................1702.1mW
Operating Temperature Range......................... -40NC to +125NC
Storage Temperature Range............................. -65NC to +150NC
Lead Temperature (soldering, 10s).................................+300NC
Soldering Temperature (reflow).......................................+260NC
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
CAUTION! ESD SENSITIVE DEVICE
DC ELECTRICAL CHARACTERISTICS
(Figure 2, 50I system impedance, VDD = +2.1V to +3.6V, fRF = 868MHz, TA = -40°C to +125°C, unless otherwise noted. Typical
values are at VDD = +3.0V, TA = +25°C, unless otherwise noted. All min and max values are 100% tested at TA = +125°C and are
guaranteed by design and characterization over temperature, unless otherwise noted.)
PARAMETER
Supply Voltage
SYMBOL
VDD
CONDITIONS
PAVDD, LOVDD, VCOVDD, CPVDD,
PLLVDD, XOVDD, DVDD, and AVDD
connected to power supply
PA off
Operating Current
IDD
Shutdown Current
Input Low Voltage
VIL
Input High Voltage
VIH
PA off,
PA predriver at
high current
setting
MIN
TYP
MAX
UNITS
2.1
3.0
3.6
V
fRF = 315MHz
11.2
fRF = 434MHz
10.4
fRF = 863MHz to 945MHz
10.2
fRF = 315MHz
13.2
fRF = 434MHz
12.4
fRF = 863MHz to 945MHz
12.2
868MHz +15dBm
POUT = +15dBm matching network with
harmonic filter
41
868MHz +10dBm
POUT = +10dBm matching network with
harmonic filter
21
TA = +25NC, Sleep mode
350
TA = +85NC, Sleep mode
600
TA = +125NC, Sleep mode
1700
TA = +25NC, Shutdown mode (registers reset)
50
TA = +85NC, Shutdown mode (registers reset)
200
TA = +125NC, Shutdown mode
(registers reset)
1300
mA
4000
nA
3500
0.2 x VDD
0.8 x VDD
V
�� Maxim Integrated Products 5
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
DC ELECTRICAL CHARACTERISTICS (continued)
(Figure 2, 50I system impedance, VDD = +2.1V to +3.6V, fRF = 868MHz, TA = -40°C to +125°C, unless otherwise noted. Typical
values are at VDD = +3.0V, TA = +25°C, unless otherwise noted. All min and max values are 100% tested at TA = +125°C and are
guaranteed by design and characterization over temperature, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
Pulldown Sink Current
12.5
Pullup Source Current
12.5
Output Low Voltage
Output High Voltage
VOL
In buffer mode, GPO1 250FA sink current,
SDO 1mA sink current, and GPO2 4mA
sink current
VOH
In buffer mode, GPO1 250FA source current,
SDO 1mA source current, and GPO2 4mA
source current
MAX
UNITS
FA
0.225
V
VDD - 0.225
AC ELECTRICAL CHARACTERISTICS
(Figure 2, 50I system impedance, VDD = +2.1V to +3.6V, fRF = 868MHz, TA = -40°C to +125°C, unless otherwise noted. Typical
values are at VDD = +3.0V, TA = +25°C, unless otherwise noted. All min and max values are 100% tested at TA = +125°C and are
guaranteed by design and characterization over temperature, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
Divide-by-1 LO divider setting
863
945
Divide-by-2 LO divider setting
431.5
472.5
Divide-by-3 LO divider setting
287.7
315
UNITS
GENERAL CHARACTERISTICS
Operating Frequency
Maximum Data Rate
Maximum Frequency Deviation
Frequency Settling Time
Manchester encoded
100
NRZ encoded
200
100kHz synthesizer loop bandwidth
tON
From Enable low-to-high transition to LO
within 5kHz of final value, 100kHz synthesizer
loop bandwidth
Q150
MHz
kbps
kHz
330
Fs
From Enable low-to-high transition to LO
within 1kHz of final value, 100kHz synthesizer
loop bandwidth
400
Match to 50I, including harmonic filter
+15
dBm
Programmable PA Bias Current
Step
With Q1% 56.2kI external PA reference
current setting resistor
0.5
mA
Programmable PA Power
Dynamic Range
Power range from decimal 1 to decimal 63
on digital PA bias current
36
dB
Modulation Depth
With respect to +10dBm output power
57
dB
Maximum Carrier Harmonics
With output matching network
-50
dBc
POWER AMPLIFIER
Maximum Output Power
PMAX
�� Maxim Integrated Products 6
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
AC ELECTRICAL CHARACTERISTICS (continued)
(Figure 2, 50I system impedance, VDD = +2.1V to +3.6V, fRF = 868MHz, TA = -40°C to +125°C, unless otherwise noted. Typical
values are at VDD = +3.0V, TA = +25°C, unless otherwise noted. All min and max values are 100% tested at TA = +125°C and are
guaranteed by design and characterization over temperature, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
FRACTIONAL-N SYNTHESIZER
VCO Gain
KVCO
Referenced to 863MHz to 945MHz LO
108
MHz/V
Close-In Phase Noise
10kHz offset, 100kHz loop BW
-101
dBc/Hz
VCO Phase Noise
1MHz offset, 863MHz to 945MHz
-126
dBc/Hz
VOUT = VCPVDD/2, low setting (icont bit = 0)
204
FA
VOUT = VCPVDD/2, high setting (icont bit = 1)
407
FA
Charge-Pump Current
ICP
1
LO Divider Settings
2
3
Minimum Synthesizer Frequency
Step
Referenced to 863MHz to 945MHz LO or
carrier frequency band
fXTAL/216
Hz
-71
dBc
48
Fs
1
VP-P
7
Bits
7.25
mV
16 to 22.4
MHz
Frequency Pulling by VDD
0.5
ppm/V
Recommended Crystal Load
Capacitance
10
Maximum Crystal Load
Capacitance
20
Reference Spur
26MHz frequency step, 902MHz to 928MHz
band, 100kHz synthesizer loop bandwidth
Frequency Switching Time
Reference Frequency Input
Level
ADC
Resolution
LSB Bit Width
CRYSTAL OSCILLATOR
Crystal Frequency
fXTAL
pF
TEMPERATURE SENSOR
Range
Digital Code Slope
-40 to +125
NC
2
NC/LSB
SPI TIMING CHARACTERISTICS (Figure 1)
Minimum SCLK Low to Falling
Edge of CS Setup Time
tSC
20
ns
Minimum CS Low to Rising Edge
of SCLK Setup Time
tCSS
30
ns
�� Maxim Integrated Products 7
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
AC ELECTRICAL CHARACTERISTICS (continued)
(Figure 2, 50I system impedance, VDD = +2.1V to +3.6V, fRF = 868MHz, TA = -40°C to +125°C, unless otherwise noted. Typical
values are at VDD = +3.0V, TA = +25°C, unless otherwise noted. All min and max values are 100% tested at TA = +125°C and are
guaranteed by design and characterization over temperature, unless otherwise noted.)
PARAMETER
SYMBOL
Minimum SCLK Low to Rising
Edge of CS Setup Time
CONDITIONS
MIN
TYP
MAX
UNITS
tHCS
30
ns
Minimum SCLK Low after Rising
Edge of CS Hold Time
tHS
20
ns
Minimum Data Valid to SCLK
Rising-Edge Setup Time
tDS
15
ns
Minimum Data Valid to SCLK
Rising-Edge Hold Time
tDH
10
ns
Minimum SCLK High Pulse
Width
tCH
30
ns
Minimum SCLK Low Pulse Width
tCL
30
ns
Minimum CS High Pulse Width
tCSH
30
ns
Maximum Transition Time from
Falling Edge of CS to Valid SDO
tCSG
CL = 10pF load capacitance from
SDO to GND
20
ns
Maximum Transition Time from
Falling Edge of SCLK to
Valid SDO
tCG
CL = 10pF load capacitance from
SDO to GND
20
ns
CS
tCSH
tCSS
tHCS
tSC
tCH
SCLK
tCL
tDH
tHS
tDS
SDI
tCSG
tCG
SDO
Figure 1. SPI Timing Diagram
�� Maxim Integrated Products 8
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
Typical Operating Characteristics
(Figure 2, 50Ω system impedance, VDD = +2.1V to +3.6V, fRF = 288MHz to 945MHz, TA = -40°C to +125°C, unless otherwise noted.
Typical values are at VDD = +3.0V, TA = +25°C, unless otherwise noted.)
1.0
VDD = 3.6V
0.8
VDD = 3.0V
0.6
VDD = 2.7V
0.4
VDD = 2.1V
0.2
0
-50
-25
0
25
50
75
100
125
VDD = 3.6V
1.6
1.4
1.2
1.0
0.8
VDD = 3.0V
VDD = 2.7V
VDD = 2.1V
0.6
0.4
0.2
0
-25
940
0
25
50
75
100
MAX7049 toc03
-50
-25
0
TA = +85˚C
25
50
75
100
125
CHARGE-PUMP CURRENT
vs. CONTROL VOLTAGE
(LOW CURRENT SETTING, 2.1V SUPPLY)
FREQUENCY SETTLING
AFTER POWER-UP
MAX7049 toc05
868.62MHz
868.60MHz
880
860
20
TEMPERATURE (°C)
920
900
40
125
TA = +25˚C
TA = +125˚C
840
250
-40˚C
200
+25˚C
+85˚C
150
100
-40˚C
+125˚C
DOWN
UP
50
820
868.58MHz
800
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
TRANSMIT FREQUENCY (MHz)
960
MAX7049 toc04
TA = -40˚C
60
TEMPERATURE (°C)
VCO TUNING CHARACTERISTIC
(IN 900MHz BAND) vs. CONTROL VOLTAGE
980
80
0
-50
TEMPERATURE (°C)
1000
100
MAX7049 toc06
1.2
1.8
120
TEMPERATURE SENSOR CODE (DECIMAL)
1.4
2.2
2.0
CHARGE-PUMP CURRENT (µA)
1.6
MAX7049 toc02
SHUTDOWN MODE CURRENT (µA)
1.8
2.4
SLEEP MODE CURRENT (µA)
MAX7049 toc01
2.0
TEMPERATURE SENSOR CODE
vs. TEMPERATURE
SLEEP MODE CURRENT
vs. TEMPERATURE
SHUTDOWN MODE CURRENT
vs. TEMPERATURE
CONTROL VOLTAGE WITH RESPECT TO SUPPLY (V)
0.00s
500.0µs
100.0µs/div
1.000ms
0
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
CONTROL VOLTAGE WITH RESPECT TO GROUND (V)
�� Maxim Integrated Products 9
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
Typical Operating Characteristics (continued)
(Figure 2, 50Ω system impedance, VDD = +2.1V to +3.6V, fRF = 288MHz to 945MHz, TA = -40°C to +125°C, unless otherwise noted.
Typical values are at VDD = +3.0V, TA = +25°C, unless otherwise noted.)
927MHz, ibsel = 1
-130
-140
10
100
1000
10,000
OFFSET FREQUENCY (kHz)
-30
-40
-50
-80
-80
-90
-90
868.590 868.594 868.598 868.602 868.606 868.610
926.990 926.994 926.998 927.002 927.006 927.010
868.592 868.596 868.600 868.604 868.608
FREQUENCY (MHz)
926.992 926.996 927.000 927.004 927.008
FREQUENCY (MHz)
0
ASK MODULATION SPECTRUM
(3kHz RBW, 4kHz SQUARE-WAVE MODULATION,
+10dBm OUTPUT POWER, WITH
+10dBm AT 3V MATCH)
0
-20
-10
-20
-50
-40
-50
-60
-60
-70
-70
-80
-80
-90
-90
-100
926.990 926.994 926.998 927.002 927.006 927.010
926.992 926.996 927.000 927.004 927.008
FREQUENCY (MHz)
POWER (dBc)
-40
-50
-70
-30
-30
-40
-60
-10
POWER (dBc)
POWER (dBc)
-20
-30
-70
UNMODULATED SPECTRUM
(palopwr = 0, 100% DUTY CYCLE,
+10dBm, 868MHz,
WITH +10dBm AT 3V MATCH)
MAX7049 toc10
-10
-20
-60
UNMODULATED CLOSE-IN SPECTRUM
(100Hz RBW, 100 SAMPLE AVERAGE,
16MHz CRYSTAL, ibsel = 0, icont = 0)
0
-10
MAX7049 toc12
-110
MAX7049 toc08
-20
POWER (dBc)
927MHz, ibsel = 0
-120
-10
POWER (dBc)
868MHz, ibsel = 0
-100
0
MAX7049 toc11
-80
PHASE NOISE (dBc/Hz)
0
MAX7049 toc07
-70
-90
UNMODULATED CLOSE-IN SPECTRUM
(100Hz RBW, 100 SAMPLE AVERAGE,
22.4MHz CRYSTAL, ibsel = 0, icont = 0)
UNMODULATED CLOSE-IN SPECTRUM
(100Hz RBW, 100 SAMPLE AVERAGE,
22.4MHz CRYSTAL, ibsel = 0, icont = 0)
MAX7049 toc09
PHASE NOISE (VCO DOMINATED)
vs. OFFSET FREQUENCY
(CL = 0.1µF, CS = 0.01µF,
R = 200I, RP = CP = 0)
UNSHAPED
-30
-40
-50
-60
GAUSSIAN
-70
848 853 858 863 868 873 878 883 888
FREQUENCY (MHz)
-80
867.75
867.85
867.80
867.95
868.05
868.15
867.90 868.00 868.10
FREQUENCY (MHz)
868.25
868.20
�� Maxim Integrated Products 10
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
Typical Operating Characteristics (continued)
(Figure 2, 50Ω system impedance, VDD = +2.1V to +3.6V, fRF = 288MHz to 945MHz, TA = -40°C to +125°C, unless otherwise noted.
Typical values are at VDD = +3.0V, TA = +25°C, unless otherwise noted.)
-10
-40
-50
-60
-70
GAUSSIAN
-80
867.85
867.80
867.95
-20
-20
-30
-30
-40
-50
868.15
867.90 868.00 868.10
FREQUENCY (MHz)
868.25
-70
-70
867.95
868.20
867.97
867.96
867.99
868.01
868.03
867.98 868.00 868.02
FREQUENCY (MHz)
-10
GAUSSIAN
-20
-40
-50
-10
868.05
UNSHAPED
-50
-80
-80
FREQUENCY (MHz)
868.03
-40
-70
868.6
868.01
-30
-60
868.2 868.4
867.99
FREQUENCY (MHz)
-20
-70
867.8 868.0
867.97
0
-60
-90
867.4 867.6
-80
867.95
FSK MODULATION SPECTRUM
(3kHz RBW, 4kHz SQUARE-WAVE MODULATION,
Q100kHz DEVIATION, +10dBm OUTPUT
POWER, WITH +10dBm AT 3V MATCH)
POWER (dBc)
-30
868.05
868.04
FSK MODULATION SPECTRUM
(3kHz RBW, 4kHz SQUARE-WAVE MODULATION,
Q100kHz DEVIATION, +10dBm OUTPUT
POWER, WITH +10dBm AT 3V MATCH)
0
-50
-60
-80
868.05
UNSHAPED
-40
-60
MAX7049 toc16
867.75
-10
MAX7049 toc17
-30
POWER (dBc)
UNSHAPED
POWER (dBc)
POWER (dBc)
-20
GAUSSIAN
POWER (dBc)
-10
0
MAX7049 toc14
0
MAX7049 toc13
0
FSK MODULATION SPECTRUM
(1kHz RBW, 4kHz SQUARE-WAVEMODULATION,
±4kHz DEVIATION, +10dBm OUTPUT POWER,
WITH +10dBm AT 3V MATCH)
FSK MODULATION SPECTRUM (1kHz RBW,
4kHz SQUARE-WAVE MODULATION,
±4kHz DEVIATION, +10dBm OUTPUT
POWER, WITH +10dBm AT 3V MATCH)
MAX7049 toc15
ASK MODULATION SPECTRUM
(3kHz RBW, 4kHz SQUARE-WAVE MODULATION,
+9dBm OUTPUT POWER, WITH
+10dBm AT 3V MATCH)
-90
867.4 867.6
867.8 868.0
868.2 868.4
868.6
FREQUENCY (MHz)
�� Maxim Integrated Products 11
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
Typical Operating Characteristics (continued)
(Figure 2, 50Ω system impedance, VDD = +2.1V to +3.6V, fRF = 288MHz to 945MHz, TA = -40°C to +125°C, unless otherwise noted.
Typical values are at VDD = +3.0V, TA = +25°C, unless otherwise noted.)
PA POWER vs. PA CODE
(palopwr = 0, 100% DUTY CYCLE, 915MHz,
WITH +15dBm AT 3V MATCH)
15
VDD = 3.0V
10
POUT (dBm)
VDD = 3.6V
3.6V
10.30
10.20
10.10
VDD = 2.1V
10
3.0V
2.1V
5
3.6V
15
POUT (dBm)
10.40
20
MAX7049 toc19
10.50
9.90
0
-5
-5
0
25
50
75
100
-10
125
0
TEMPERATURE (°C)
8
16
24
32
40
48
56
64
0
10
12
POUT (dBm)
0
40
48
56
64
PA CODE 39
8
6
4
PA CODE 19
2
-5
32
14
10
2.4V 2.7V 3.0V 3.3V 3.6V
24
PA POWER vs. PA CODE
(palopwr = 0, 100% DUTY CYCLE, 868MHz,
WITH +15dBm AT 3V MATCH)
MAX7049 toc21
15
2.1V
16
PA CODE (DECIMAL)
PA POWER vs. PA CODE
(palopwr = 1, 100% DUTY CYCLE, 868MHz,
WITH +10dBm AT 3V MATCH)
5
8
PA CODE (DECIMAL)
MAX7049 toc22
-25
5
0
-10
-50
3.0V
2.1V
VDD = 2.7V
10.00
POUT (dBm)
Tx CURRENT (mA)
20
MAX7049 toc18
10.60
PA POWER vs. PA CODE
(palopwr = 0, 100% DUTY CYCLE, 868MHz,
WITH +15dBm AT 3V MATCH)
MAX7049 toc20
Tx CURRENT vs. TEMPERATURE
(PA OFF, 900MHz BAND, palopwr = 1)
PA CODE 10
0
-2
-10
0
8
16
24
32
40
PA CODE (DECIMAL)
48
56
64
-50
-25
0
25
50
75
TEMPERATURE (°C)
100
125
�� Maxim Integrated Products 12
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
CS
SDI
SCLK
ENABLE
DATAIN
SDO
TOP VIEW
GPO2
Pin Configuration
21
20
19
18
17
16
15
DVDD 22
14
N.C.
HOP 23
13
XTALB
GPO1 24
12
XTALC
SHDN 25
11
XOVDD
10
N.C.
9
PLLVDD
8
CPOUT
MAX7049
AVDD 26
PA+ 27
EP
4
5
6
7
CTRL
CPVDD
PAVDD
REXTPA
3
VCOVDD
2
N.C.
1
LOVDD
+
PA- 28
TQFN
(5mm x 5mm)
Pin Description
PIN
NAME
1
PAVDD
Power Amplifier Supply Voltage Input. Bypass to ground with 33pF capacitor as close as possible to the pin.
FUNCTION
2
REXTPA
External PA Bias Current Setting Resistor Connection. Couple to ground through a Q1% tolerance lowtemperature coefficient resistor. A resistor of 56.2kI is recommended for a 0.5mA nominal PA bias
current DAC LSB value.
3, 10,
14
N.C.
4
LOVDD
5
VCOVDD
6
CTRL
No Connection. Leave unconnected.
Local Oscillator (LO) Supply Voltage Input. Bypass to ground with 33pF capacitor as close as possible
to the pin.
Voltage-Controlled Oscillator (VCO) Supply Voltage. Bypass to ground with 1FF capacitor as close as
possible to the pin.
Control (Tuning) Voltage for VCO Input. Referenced to VCOVDD pin. Connect through passive loop filter to
CPOUT.
7
CPVDD
Charge-Pump Supply Voltage Input. Bypass to ground with 0.01FF capacitor as close as possible to the pin.
8
CPOUT
Charge-Pump Output. Connect through passive loop filter to CTRL.
9
PLLVDD
Synthesizer Supply Voltage Input. Bypass to ground with 33pF capacitor as close as possible to the pin.
11
XOVDD
Crystal Oscillator Supply Voltage Input. Bypass to ground with 0.1FF capacitor as close as possible to
the pin.
�� Maxim Integrated Products 13
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
Pin Description (continued)
PIN
NAME
FUNCTION
12
XTALC
Collector Crystal Input. Connect to crystal either directly or through an AC-coupling capacitor. A shunt
capacitance to ground might be needed depending on the specified load capacitance of the crystal and
PCB stray capacitances. Can be driven by an AC-coupled external reference with a signal swing of
0.8VP-P to 1.2VP-P.
13
XTALB
Base Crystal Input. Connect to crystal either directly or through an AC-coupling capacitor. A shunt
capacitance to ground might be needed depending on the specified load capacitance of the crystal and
PCB stray capacitances. Must be DC shorted to ground if XTALC is driven by external reference.
15
SDO
16
DATAIN
Transmitter Data Input. The Datain function can also be controlled by SPI. Internally pulled to ground.
17
ENABLE
Enable. Drive high for active operation. Drive low or leave unconnected to put the device into Sleep mode.
The enable function can also be controlled by SPI. Internally pulled to ground.
18
SCLK
19
SDI
20
SPI Active-Low Chip Select. Internally pulled to supply.
21
CS
GPO2
22
DVDD
Digital Supply Voltage Input. Bypass to ground with 0.1FF capacitor as close as possible to the pin.
23
HOP
24
GPO1
General-Purpose Output 1. Low drive strength digital general-purpose output.
25
SHDN
Shutdown Digital Input. Turns off internal power-on-reset (POR) circuit when driven high. Register contents
are set to the initial state when driven high. Must be driven low for normal operation. Not internally pulled to
supply or ground.
26
AVDD
Analog Supply Voltage Input. Bypass to ground with a 1FF capacitor as close as possible to the pin.
27
PA+
Power Amplifier (PA) Positive Output. Requires DC current path to supply voltage through an inductive path.
The DC current path can be part of the output impedance matching and harmonic filter network.
28
PA-
Power Amplifier (PA) Negative Output. Requires DC current path to supply voltage through an inductive path.
The DC current path can be part of the output impedance matching and harmonic filter network.
—
EP
Exposed Pad. This is the only ground connection. Solder evenly to the PCB ground plane for proper
operation. Multiple vias from the solder pad to the PCB ground plane are recommended.
Serial Peripheral Interface (SPI) Data Output. It can also be configured as a general-purpose digital output.
SPI Clock. Internally pulled to ground.
SPI Data Input. Internally pulled to ground.
General-Purpose Output 2. High drive strength digital general-purpose output.
Frequency Hop Pin. Transfers the base[20:0] bits to the fractional-N divider. See the Fractional-N Synthesizer
section. The hop function can also be controlled by SPI. Internally pulled to ground.
�� Maxim Integrated Products 14
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
Functional Diagram
27
28
PA+ PASHDN* 25
MAX7049
2 REXTPA
6
PA
GPO1* 24
ADC
7
HOP* 23
TEMPERATURE
SENSOR
GPO2* 21
/1, /2, OR /3
8 CPOUT
CS 20
DIGITAL
CONTROL
AND MCU
INTERFACE
CHARGE
PUMP
SDI 19
SCLK 18
6 CTRL
FRACTIONAL-N
DIVIDER
PFD
ENABLE* 17
VCO
21
GROUNDED
PAD (EP)
DATAIN* 16
SDO* 15
XTAL OSCILLATOR
XTALC
XTALB
12
13
Detailed Description
Architectural Overview and
Applications Circuit
The MAX7049 includes a single precision local oscillator
fractional-N synthesizer with an integrated VCO, fractional-N divider, phase/frequency detector, charge pump,
LO divider, and lock detector. The loop filter is located
off-chip to allow the user to optimize the synthesizer noise
and transient characteristics for a particular application.
In FSK transmit mode, the synthesizer transitions between
the mark and the space frequency based on the state
of the DATAIN pin or datain bit (Datain register, 0x3D,
bit 6). A user-programmable frequency-shaping function
enables the user to precisely define the transition from the
mark frequency to the space frequency and vice versa to
minimize spectral width of the modulated Tx waveform.
* OPTIONAL I/Os FROM/TO MCU.
The bias current of the output stage is set with a combination of an external resistor and an internal amplitudeshaping function. The programmable shaping function enables the user to precisely define the transition
between carrier on and carrier off and vice versa based
on the state of the DATAIN pin or datain bit so as to
minimize the spectral width of the modulated Tx signal.
Linear amplitude ramping is used in FSK mode as the PA
is enabled at the beginning of a data burst and disabled
at the end of a data burst for spectral control.
A complete transmitter system can be built using a
low-end MCU, the IC, a crystal, and a small number of
passive components for power-supply bypassing and for
RF matching, as illustrated in Figure 2.
Communication between the MCU and the IC is accomplished through a 4-pin SPI bus and a number of optional
digital inputs and outputs.
The IC utilizes a differential emitter-coupled, dual-opencollector power amplifier for the transmitter output.
�� Maxim Integrated Products 15
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
C13
L1
DASHED LINES DENOTE OPTIONAL CONNECTIONS
C20
J1
C14
L3
L4
C12
L2
C11
50I
+
VDD
PAVDD
28
27
26
25
24
23
DVDD
HOP
GPO1
SHDN
AVDD
PA-
C15
PA+
C16
C17
22
1
21
2
20
3
19
4
18
C1
REXTPA
R1
N.C.
LOVDD
C2
C3
VCOVDD
CTRL
CPVDD
R2
MAX7049
5
17
GROUNDED
PAD (EP)
6
16
7
15
GPO2
CS
SDI
µP
SCLK
ENABLE
DATAIN
SDO
C4
C7
C8
14
N.C.
13
XTALB
12
11
XTALC
10
XOVDD
9
N.C.
8
PLLVDD
C5
CPOUT
C6
Y1
C9
C10
Figure 2. Typical Operating Circuit
�� Maxim Integrated Products 16
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
Digital Inputs and Outputs
Digital Inputs
The IC’s SPI inputs are the CS, SCLK, and SDI pins. The
CS pin is active low, so this pin has an internal pullup.
The SCLK and SDI pins have internal pulldowns. In addition to the SPI inputs, there are also a number of optional
digital inputs to the IC. These inputs are DATAIN,
ENABLE, and HOP. These optional inputs, which have
internal pulldowns, give the user the option to control an
internal signal by either driving the pin to the appropriate
logic level or by setting a control bit to the appropriate
state. This is illustrated in Figure 3.
Digital Outputs
The IC has two dedicated general-purpose outputs
(GPO1 and GPO2), one SPI output (SDO) that can also
serve as a general-purpose output when CS is high. The
GPO1, GPO2, and SDO pins can be configured to output
various internal status signals and clocks, as illustrated
in Figure 4.
The outputs (GPO1 and GPO2) offer a feature where the
pin can operate either as a digital buffer or as a currentlimited source/sink output, as illustrated in Figure 5.
SPI control minimizes the number of I/Os required
between the IC and the MCU, whereas the pin control
eliminates the configuration overhead associated with
SPI communication.
22 DVDD
22 DVDD
22 DVDD
INTERNAL
CSB
SIGNAL
20 CS
INTERNAL
INPUT
SIGNAL
INPUT
‘OR’
INPUT
INPUT
GROUNDED
PAD (EP)
GROUNDED
PAD (EP)
INTERNAL
INPUT
SIGNAL
PROGRAMMABLE
CONTROL BIT
GROUNDED
PAD (EP)
INPUT = SCLK AND SDI
INPUT = DATAIN, ENABLE, AND HOP
SPI INPUTS
Figure 3. Digital Inputs
Table 1. Optional Digital Input Controls
PIN
BIT NAME
REGISTER
NAME
REGISTER
ADDRESS (hex)
BIT LOCATION (7:0)
FUNCTION
DATAIN
datain
Datain
0x3D
6
Data input to transmitter.
ENABLE
enable
EnableReg
0x3E
0
Enable input for transmitter.
HOP
hop
FLoad
0x0B
0
Initiates the transition to the next
frequency as defined by base[20:0].
�� Maxim Integrated Products 17
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
sdos[3:0]
SPI READ-ONLY REGISTERS
TestBus0 AND TestBus1 (0x40 AND 0x41)
tmux[3:0]
INTERNAL SIGNALS
MUX
SDO 15
MUX
gp1s[3:0]
tbus[15:0]
gp1md[1:0]
GPO1 24
MUX
gp2s[3:0]
gp1isht
[15:4]
MAX7049
plllock
xtal
/16
ckdiv[1:0]
/1, /2,
/4, OR /8
gp2md[2:0]
GPO2 21
MUX
/1, /2,
/4, OR /8
gp2isht
/5, /6, mclk /1, /2,
/7, OR /8
/4, OR /8
clksht
XTALC
12
XTALB
xtal[1:0]
13
Figure 4. Digital Outputs
BUFFER MODE
CURRENT MODE
DVDD 22
DVDD 22
ISOURCE
INTERNAL
SIGNAL
OUTPUT
GROUNDED
PAD (EP)
OUTPUT
INTERNAL
SIGNAL
ISINK
GROUNDED
PAD (EP)
Figure 5. Digital Output Options
�� Maxim Integrated Products 18
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
The current mode of operation can reduce digital noise
associated with large supply current spikes. The GPO1
pin has a relatively small current drive capability (80µA
or 160µA). The IOConf2 register (0x05) (gp1md[1:0] bits)
control the current settings:
and xtal is the crystal frequency, and mclk is the master
digital clock. The master digital clock is the divided crystal
frequency given by the xtal[1:0] bits (Conf0 register, 0x01),
according to:
xtal[1:0]
Divide by
gp1md[1:0]
Mode
00
5
0x
Buffer mode
01
6
10
80µA sink/source capability
10
7
11
160µA sink/source capability
11
8
GPO2 has a much larger current drive capability (up to
4mA), as this GPO can be the source of output clock
signals. The IOConf2 register (0x05) (gp2md[2:0] bits)
control the current settings:
If a clock output on GPO2 is required even when the IC
is in Sleep mode (ENABLE pin and enable bit reset to 0),
the SHDN pin is reset to 0, and the clksht bit (IOConf2
register, 0x05, bit 3) must be set to 1.
gp2md[2:0] Mode
0xx
Buffer mode
100
1.0mA sink/source capability
101 2.0mA sink/source capability
A very useful function of the GPOs is to output status
signals that reflect the state of the transmitter at any
particular instance in time. See the Register Details
section for an in-depth description of the status signals
available for the TestBus0 and TestBus1 registers.
110 3.0mA sink/source capability
111 4.0mA sink/source capability
Two other bits also control the operation of GPO1 and
GPO2. The IOConf0 register (0x03) (gp1isht and gp2isht
bits) allows the current mode operation to continue even
if the IC is disabled (Sleep mode).
The GPO2 pin is designated as the primary output for
driving a clock, as it has the strongest buffer and highest
current output capabilities.
Serial Peripheral Interface (SPI)
The IC utilizes a 4-wire SPI protocol for programming its
registers, configuring and controlling the operation of the
whole transmitter.
The following digital pins control the operation of the SPI:
CS:
Active-low SPI chip select
SDI:
SPI data input
SCLK: SPI serial clock
The GPO2 clock signal can be selected by the gp2s[3:0]
and ckdiv[1:0] bits (IOConf0 register, 0x03).
SDO:
SPI data output
gp2s[3:0]
GPO2 Output
0000
plllock
0001
mclk /(ckdiv divider)
0010
xtal/(ckdiv divider)
Any number of 8-bit data bursts (Data 1, Data 2, … Data
N) can be sent within one low cycle of CS, to allow for
burst-write or burst-read operations. The SDO pin acts
as another general-purpose output (GPO) when the CS
pin is high.
0011
xtal/16/(ckdiv divider)
The SPI operates on a byte format, as shown in Figure 6.
where the ckdiv divider is given by:
ckdiv[1:0]
Divide by
00
1
01
2
10
4
11
8
�� Maxim Integrated Products 19
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
CS
SCLK
SDI
DI7
DI6
DI5
DI4
DI3
DI2
DI1
DI0
DI7
DI6
DI5
DI4
DI3
DI2
DI1
DI0
SDO
DO7
DO6
DO5
DO4
DO3
DO2
DO1
DO0
DO7
DO6
DO5
DO4
DO3
DO2
DO1
DO0
DATA 1
DATA N
Figure 6. SPI Format
SPI Commands
The following commands are implemented in the IC:
Write: Within the same CS cycle, a write command is implemented as follows:
SDI:
<0x01> <Initial Address> <Data 1> <Data 2> … <Data N>
With this command, Data 1 is written to the address given by <Initial Address>, Data 2 is written to <Initial Address +
1>, and so on.
Read: Within the same CS cycle, a read command is implemented as follows:
SDI:
<0x02> <Address 1> <Address 2> <Address 3> … <Address N>
SDO:
<0xXX>
<0xXX>
<Data 1>
<Data 2>
<0x00>
… <Data N - 1> <Data N>
With this command, all the registers can be read within the same cycle of CS. The addresses can be given in any order.
Read All: With two CS cycles, the Read All command is implemented as follows:
SDI:
CS Cycle 1
<0x03> <Address N>
CS Cycle 2
SDO:
<0x00>
<0x00>
<0x00>
…
<0x00>
<Data N> <Data N + 1> <Data N + 2> … <Data N + n>
Reset: A SPI reset command is implemented as follows:
SDI:
<0x04>
An internal active-low master resetb signal is generated, from the falling edge of the last SCLK signal to the falling edge
of the following CS signal (tHCS + tCSH).
CS
SCLK
SDI
A7 A6 A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0
WRITE COMMAND (0x01)
INITIAL ADDRESS (A[7:0])
DATA 1
D7
D0
DATA N
Figure 7. SPI Write Command Format
�� Maxim Integrated Products 20
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
CS
SCLK
SDI
A7 A6 A5 A4 A3 A2 A1 A0 A7 A6 A5 A4 A3 A2 A1 A0 A7
READ COMMAND (0x02)
ADDRESS 1
ADDRESS 2
SDO
A0
ADDRESS N
D7 D6 D5 D4 D3 D2 D1 D0 D7
DATA 1
0x00
D0 D7
DATA 2
D0
DATA N
Figure 8. SPI Read Command Format
CS
SCLK
A7 A6 A5 A4 A3 A2 A1 A0
SDI
READ-ALL COMMAND (0x03)
ADDRESS N
SDO
D7 D6 D5 D4 D3 D2 D1 D0 D7
DATA N
D0 D7
D0
DATA N + 1 DATA N + n
Figure 9. SPI Read-All Command Format
INITIAL
CS
SHUTDOWN
SCLK
SLEEP
SLEEP
XTAL ON
SDI
SPI
CONFIGURATION
TEMPERATURE
SENSOR
RESET COMMAND (0x04)
resetb
Tx
FSK
ASK
Figure 10. SPI Reset Command Format
Figure 11. Operating Modes
Operating Mode Overview
The IC offers several modes of operation that allow the
user to optimize the transmitter’s power consumption for
a particular application. The primary operating modes
are Initial, Sleep, Temperature Sensor, and Tx, as illustrated in Figure 11.
When the SHDN pin is high, the IC is in Shutdown mode.
In Shutdown mode, the POR circuit internal to the IC is
disabled and draws virtually no current. In Shutdown
mode, all internal data registers are reset to the initial
states and must be rewritten for desired transmitter
operation after the SHDN pin is driven low.
�� Maxim Integrated Products 21
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
When the SHDN pin is low, the POR circuit is active and
holds the internal data registers in the initial state until the
power supply is above 2.1V and the IC enters the Initial
mode. From the Initial mode, the IC can be configured
for operation in Sleep mode, Temperature Sensor mode,
or Tx mode. In Sleep mode, there are two options available: Sleep and XTAL ON. In Sleep mode, the current
drain is typically 350nA. All register states are retained in
Sleep mode. In XTAL ON mode, controlled by the clksht
bit (IOConf2 register, 0x05, bit 3), the crystal oscillator is
enabled and the divided output of the crystal oscillator
(/1, /2, /4, /8, as set by the ckdiv[1:0] bits (IOConf0 register, 0x03, bits [5:4]) can be directed to GPO2. The XTAL
ON mode is designed so an accurate high-speed clock
is always available to the MCU.
In Temperature Sensor mode, the internal temperature
sensor function can be executed.
In Tx mode, the transmitter can be configured to transmit
ASK data or FSK data.
Table 2. Mode Control Logic
The Tx mode is determined by the logic states of the
SHDN pin, ENABLE pin, and the enable bit (EnableReg
register, 0x3E, bit 0). The transmitter is enabled if the
SHDN pin is driven low and the ENABLE pin is driven
high, or the enable bit is set. This logic is summarized
in Table 2.
The mode options are selected by the mode SPI bit
(Conf0 register, 0x01, bit 4) and these options are
summarized in Table 3.
Sleep Mode
From the Initial mode, the transmitter directly enters
Sleep mode. In XTAL ON mode, the crystal oscillator is
enabled and the divided output of the crystal oscillator
can be directed to GPO2. This mode is enabled when
the RF functions are disabled and the clksht bit is set.
The current drain in this mode is highly dependent on the
frequency of the output signal and the load capacitance
on the GPO2 pin. The current drain is typically 750µA
when the output signal is 3.2MHz and the load capacitance is 10pF. See the Digital Outputs section for more
details. Table 4 summarizes the Sleep mode functions.
Table 4. Sleep Mode Summary
SHDN PIN
ENABLE PIN
enable BIT
TRANSMITTER
MODE
0
0
0
Sleep
0
0
1
Tx
0
1
0
Tx
0
1
1
Tx
1
0
0
Shutdown
1
0
1
Shutdown
1
1
0
Shutdown
1
1
1
Shutdown
SLEEP
MODE
SETTINGS
TYPICAL
CURRENT
DRAIN
Sleep
Enable = 0
350nA
All register contents
are retained.
XTAL
ON
clksht = 1
750FA*
Divided XTAL
oscillator signal can
be directed to GPO2.
COMMENTS
*Dependent on GPO2 load capacitance and output clock
frequency.
Table 3. Mode Option Logic
mode BIT
MODE OPTION
0
ASK
1
FSK
�� Maxim Integrated Products 22
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
Temperature Sensor Mode
The user must initiate the temperature sensor from Sleep
mode, and the transmitter automatically returns to sleep
when the measurement sequence is completed.
The on-chip temperature sensor is enabled when the
tsensor bit (EnableReg register, 0x3E, bit 3) is set. Once
the internal analog temperature sensor circuit has settled,
an A/D conversion is performed and the resultant ADC
value is stored in the tsadc[6:0] bits that are accessed
through the TestBus1 register (0x41, bits 6:0) when the
digital test mux bits tmux[3:0] (TestMux register, 0x3C,
bits 3:0) are set to 0. The tsensor bit is a self-reset bit,
so it returns to a zero state once the temperature sensor
measurement is completed. The tsdone status bit (Status1
register, 0x43, bit 4) is also set when the measurement
is completed. The current drain in Temperature Sensor
mode is less than 1mA and the sensor settling time plus
the ADC conversion time is less than 2ms. The pertinent
features of the Temperature Sensor mode are summarized in Table 5.
Tx Mode
There are two subsets of the Tx mode. These subsets
include FSK and ASK.
The transmitter output signal is generated by the fractional-N
synthesizer, then buffered, and amplified by the power
amplifier (PA) to the programmed output power level. There
is a finite warmup time for the transmitter. Upon entering Tx
mode from Sleep mode, the following sequence occurs:
1) The crystal oscillator is enabled and settles to a steady
state. The rising edge of the internal ckalive status signal indicates that the crystal oscillator has settled and
an accurate time base is available. All other Tx modules
are enabled except the PA. The synthesizer settles to
the desired LO frequency at the same time the other
Table 5. Temperature Sensor Mode
Summary
BIT
tsensor
EXECUTION
TIME (ms)
<2
TYPICAL
CURRENT
DRAIN (mA)
COMMENTS
<1
The tsdone status
bit is set when the
measurement is
completed. The
results are stored in
tsadc[6:0].
modules settle to their desired operating points.
A rising edge of the lockdet status signal indicates
that the synthesizer has locked. In some narrowband applications, the lockdet signal can effectively
be delayed with the plldl[2:0] bits (Conf1 register,
0x02, bits 5:3) to ensure that the synthesizer has
settled to within the desired accuracy. This delayed
signal is called plllock. The rising edge of the txready
status signal is coincident with the rising edge of the
plllock signal.
2) In ASK mode, the power amplifier ramp-up sequence
begins on the rising edge of either the DATAIN pin
or the datain bit after the internal txready signal
transitions high. In FSK mode, the power amplifier
linear ramp-up sequence begins on the rising edge
of the txready signal.
Figure 12 illustrates this warmup sequence.
In an ASK application, the output of the synthesizer
is fixed at the carrier frequency. The output power is
alternated between fully off when both the DATAIN
pin is logic 0 and the datain bit is cleared, and the
programmed output power level when either the DATAIN
enable
‘OR’
ENABLE
ckalive
105µs
(typ)
95µs
(typ)
lockdet
plldel
INTERVAL
plllock
txready
datain
‘OR’
DATAIN
PAQ*
USER-DEFINED PA RAMP
(*PA RAMP BEGINS ON THE RISING EDGE OF DATAIN IN ASK MODE
AND ON THE RISING EDGE OF txready IN FSK MODE.)
Figure 12. Tx Warmup Timing Diagram
�� Maxim Integrated Products 23
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
pin is logic 1 or the datain bit is set. The output signal
can be waveshaped in amplitude to reduce the spectral
width of the transmission. See the Power Amplifier section
for more information regarding amplitude waveshaping.
The PA power is determined by the 6-bit amplitude word
that linearly controls the PA output bias current. The LSB
current amplitude is set by an off-chip resistor placed
between the REXTPA pin and ground. The LSB current is
nominally 0.5mA for a 56.2kI resistor and allows for very
tight transmitter power control with a low-temperature
coefficient ±1% tolerance resistor.
In an FSK application, the output of the synthesizer
alternates between the space frequency when both the
DATAIN pin is logic 0 and the datain bit is cleared, and
the mark frequency when either the DATAIN pin is logic 1
or the datain bit is set. The output signal can be waveshaped in frequency to reduce the spectral width of the
transmission. See the Fractional-N Synthesizer section
for more information regarding frequency waveshaping.
The PA power is determined by the 6-bit amplitude word.
The PA output power linearly ramps between fully off and
the programmed power when the transmitter is enabled
or disabled. The ramp slope is also programmable. To
transmit the entire message at the desired power level,
the user should wait until the PA ramp is completed
before initiating the data sequence.
INITIAL STATE
ENABLE
Figure 13 shows the recommended sequence during
FHSS operation.
Use of the hop bit is preferred during initial configuration.
Use of the HOP pin is preferred over the hop bit during
active transmitter operation. This eliminates the possibility
of SPI activity during active transmitter operation and
allows for exact control of transmitter timing.
SET fska
TO ZERO
HOP
LOAD FIRST
CHANNEL
(FBase)
**CAN BE COMPLETED IN A SINGLE SPI BURST**
NO
The typical current drain in Tx mode is 10.2mA (low-power buffer mode) or 12.2mA (high-power buffer mode) plus
the programmable PA output current. The buffer power
mode is controlled by the palopwr bit (TxConf0 register,
0x0C, bit 7) and is in low-power mode when the bit is set.
Frequency-Hopping SpreadSpectrum (FHSS) Operation
The IC is fully capable of FHSS operation. The fastsettling fractional-N synthesizer and amplitude-shaping
PA work in concert to allow clean, time efficient, and
easy-to-implement frequency hopping under the control
of a low-end MCU.
CONFIGURE
LOAD SECOND
CHANNEL
(FBase)
SET fska TO
DESIRED VALUE
IF FSK MODE
DISABLE
SLEEP STATE
ENABLE
HOP
TRANSMITTER
ACTIVITY
WARMUP
SYNTHESIZER
FORCED OUT
OF LOCK
FSK MODE
ckalive
TRANSITIONS
HIGH
YES
YES
PA
RAMPED
DOWN
NO
YES
END
TRANSMITTER
ACTIVITY
SYNTHESIZER
FREQUENCY
CHANGED
LOAD NEXT
CHANNEL
(FBase)
NO
YES
SYNTHESIZER
ACQUIRES LOCK
HOP PIN
HELD
LOGIC 1
NO
FSK
TRANSMITTER
MODE
YES
PA RAMPED
UP
NO
Figure 13. Frequency-Hopping Spread-Spectrum (FHSS)
Flowchart
�� Maxim Integrated Products 24
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
Functional Descriptions
Crystal Oscillator
The IC’s crystal oscillator circuitry is designed to operate
in conjunction with a parallel resonant crystal to generate
the fractional-N synthesizer reference frequency and the
clock signal for the digital control block. Only the crystal,
attached between pins XTALB and XTALC, and two
optional loading capacitors are typically required.
The oscillator typically presents a load capacitance of
approximately 8pF between the pins of the crystal when
PCB stray capacitance is considered. Capacitance
must be added equally from pin XTALC to ground
and pin XTALB to ground to operate the crystal at the
specified crystal load capacitance. If the crystal is
operated at a load capacitance different from the
specified load capacitance, the oscillation frequency
is pulled away from the specified operating frequency,
introducing an error in the fractional-N synthesizer reference frequency. Crystals specified to operate with higher
load capacitance than the applied load capacitance
oscillate at a higher than specified frequency.
XTALC
XTALB
12
13
CBLOCK
CBLOCK
CLOAD
CLOAD
fP =
CM 
1

2  C CASE + C LOAD
−

1
6
 × 10
C CASE + C SPEC 
where:
fP is the amount the crystal frequency is pulled in
ppm.
CM is the motional capacitance of the crystal.
CCASE is the case capacitance (includes package
capacitance and crystal blank capacitance).
CSPEC is the specified load capacitance.
CLOAD is the applied load capacitance.
When the crystal is loaded as specified (i.e., CLOAD =
CSPEC), the frequency pulling equals zero.
The oscillator circuitry is designed to operate with crystal
load capacitances between 8pF and 20pF. Operation at
an applied load capacitance of 10pF is recommended for
optimal startup times. Operation with applied load capacitances greater than 20pF can prevent oscillator startup.
The operating range of the crystal oscillator is 16.0MHz
to 22.4MHz. To maintain an internal 3.2MHz time base
mclk, the xtal[1:0] (Conf0 register, 0x01, bits 1:0), must
be programmed as shown in Table 6. The 3.2MHz
internal time base is recommended for all data rates
below 80kbps (Manchester coded) or 160kbps (NRZ
coded). For higher data rates (up to 100kbps (Manchester
coded) or 200kbps (NRZ coded)), a 4MHz internal time
base is needed, as shown in Table 6.
MAX7049
OPTIONAL
BLOCKING
CAPACITORS
SHORT IF NOT
REQUIRED
Frequency pulling from the specified operating frequency
can be calculated if the electrical parameters of the crystal
are known. The frequency pulling is given by:
LOADING CAPACITORS
(USED ALONG WITH THE IC INTERNAL CAPACITANCE AND PCB STRAY
CAPACITANCE TO APPLY SPECIFIED LOAD CAPACITANCE TO THE CRYSTAL.)
Figure 14. Recommended Crystal Connection to the IC
The crystal initial tolerance, temperature coefficient,
and aging must be specified so that the cumulative
error between the transmitter and companion receiver
frequencies allows proper operation. The transmitted
signal must be downconverted by the companion receiver
so that all necessary modulation sidebands are within the
Table 6. Crystal Divider Programming
CRYSTAL FREQUENCY
(MHz)
CRYSTAL DIVIDER RATIO
xtal[1:0] Conf0 REGISTER,
ADDRESS 0x01, BITS 1:0
mclk (MHz)
16.0
5
00
3.2
19.2
6
01
3.2
22.4
7
10
3.2
20.0
5
00
4.0
Note: The combinations of crystal frequency and divide ratio in this table are recommended, but not all inclusive.
�� Maxim Integrated Products 25
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
passband of the predemodulation filter to operate properly.
For channelized operation, the transmitted signal, including modulation sidebands, must be contained within a
given frequency range, placing limits on the crystal initial
tolerance, temperature coefficient, and aging.
The VCO operates over the entire specified frequency
range with no calibration required. The typical VCO gain
is 108MHz/V and the typical phase noise is -126dBc/
Hz at 1MHz offset. The phase noise improves by
20 x log10(2) for divide-by-2 LO frequency-divider
operation, and improves by 20 x log10(3) for divideby-3 LO frequency divider operation. The VCO control
voltage is applied at the CTRL pin and is referenced
to the VCOVDD pin. The ibsel bit (Conf1 register, 0x02,
bit 6) sets the VCO bias current. The VCO current
increases by 1mA with the ibsel bit set. The VCO phase
noise improves to -128dBc/Hz at 1MHz offset with the
additional current drain.
The IC provides a temperature sensor and a fine-step
fractional-N synthesizer to ease crystal frequency stability requirements. This sensor can be used by the system
MCU along with the crystal temperature coefficient to
calculate the necessary frequency correction and adjust
the fractional-N synthesizer in fXTAL/216Hz steps.
The IC allows for an external reference signal to be
applied in place of a crystal. The external reference
signal should be applied to pin XTALC through an
AC-coupling capacitor at an amplitude between 0.8VP-P
and 1.2VP-P with pin XTALB DC grounded.
The charge pump operates within a typical compliance
range of 0.4V to 0.4V below the supply voltage. The
typical charge-pump current is 204FA with the icont bit
(Conf1 register, 0x02, bit 7) reset. It nearly doubles to 407FA
with icont set. The CPOUT pin is the charge-pump output.
Fractional-N Synthesizer
The IC contains a fully integrated fractional-N synthesizer with the exception of a passive off-chip loop filter
for generating the transmitted signal frequency. This
includes an on-chip voltage-controlled oscillator
(VCO), charge pump, phase-frequency detector (PFD),
fractional-N frequency divider, LO frequency divider,
and all necessary support circuitry. The on-chip
crystal oscillator generates the reference frequency for
the fractional-N synthesizer.
Tx ASK Mode
The fractional-N frequency divider is programmed with
a 21-bit divider word. The divider word consists of a
5-bit integer portion and a 16-bit fractional portion as
illustrated in Figure 15.
The parameter D is the fractional-N divider ratio, where:
D = 32 + base[20:0]/216
and therefore, the synthesizer output frequency is given by:
The operating range of the fractional-N synthesizer is
863MHz to 945MHz. The LO frequency divider has
three modes: divide by 1, divide by 2, and divide by 3.
This allows for operation at frequencies of 863MHz
to 945MHz, 431.5MHz to 472.5MHz, and 287.7MHz
to 315MHz, respectively. The frequency resolution is
fXTAL/216 in the 863MHz to 945MHz range, and is
smaller at the LO frequency-divider output by the LO
division ratio. The division ratio of the LO frequency
divider is set by the fsel[1:0] bits (Conf0 register, 0x01,
bits 3:2). These division ratios are shown in Table 7.
fSYNTH = D x fXTAL
where fXTAL is the reference frequency generated by the
crystal oscillator.
The 21-bit divider word as defined by the contents of the
FBase0, FBase1, and FBase2 registers is latched into the
fractional-N divider on the rising edge of the Hop signal,
which is the logical OR of the HOP input pin and the hop
bit (FLoad register, 0x0B, bit 0), when the IC is enabled.
Table 7. LO Frequency-Divider Modes
fsel[1:0] Conf0 REGISTER, ADDRESS
0x01, BITS 3:2
LO DIVISION RATIO
TRANSMITTER OPERATING
FREQUENCIES (MHz)
00
3
287.7 to 315
01
2
431.5 to 472.5
10
Not used
N/A
11
1
863 to 945
�� Maxim Integrated Products 26
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
Figure 15 illustrates the synthesizer operation in Tx ASK
mode, where the Tx carrier frequency is static. For Tx
FSK applications, where the frequency of the carrier
alternates between the space frequency and the mark
frequency based on the Datain input, the IC includes a
frequency waveshaping function that allows the user to
control the spectral width of the transmit signal.
Tx FSK Mode Using Frequency Waveshaping
The inputs to the waveshaping function are illustrated in Figure 16. In this mode, the wsoff bit
(TxConf0 register, 0x0C, bit 6) is cleared and the
wsmlt[1:0] bits (TxConf1 register, 0x0D, bits 7:6) are
cleared. The base[20:0] bits set the divider ratio for
the lowest (space) frequency and base1[20:0] corresponds to the divider ratio for the highest (mark)
frequency. On the rising edge of the Datain signal, the
input to the fractional-N divider transitions between
base[20:0] and base1[20:0] in 20 discrete steps, as
defined by the tstep[7:0] bits (TxTstep register, 0x0E,
bits 7:0) and the shpnn[7:0] bits (Shape00–Shape18
registers, 0x0F–0x21, bits 7:0, where nn = 00 to 18), as
shown in Figure 17.
icont = 0 → CP CURRENT = 204µA
icont = 1 → CP CURRENT = 407µA
MAX7049
fTX
icont
REGISTER
Conf1,
ADDRESS
0x02, BIT 7
fsel[1:0]
REGISTER
Conf0,
ADDRESS
0x01,
BITS 3:2
/1, /2, OR /3
fsel[1:0] = 00 → /3
fsel[1:0] = 01 → /2
fsel[1:0] = 11 → /1
fSYNTH
8 CPOUT
PROGRAMMABLE
CONTROL BITS
CHARGE
PUMP
hop
REGISTER
FLoad,
ADDRESS
0x0B,
BIT 0
FRACTIONAL-N DIVIDER D
/(32 + base[20:0]/216)
PFD
VCO
108MHz/V
6 CTRL
Hop
21-BIT LATCH
ibsel
REGISTER
Conf1,
ADDRESS
0x02,
BIT 6
base[20:16]
REGISTER
FBase0,
ADDRESS
0x08,
BITS 4:0
base[15:8]
REGISTER
FBase1,
ADDRESS
0x09,
BITS 7:0
HOP 23
base[7:0]
REGISTER
FBase2,
ADDRESS
0x0A,
BITS 7:0
XTAL OSCILLATOR
fXTAL
XTALC
12
XTALB
13
Figure 15. Fractional-N Synthesizer Configuration Tx ASK Mode
�� Maxim Integrated Products 27
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
PROGRAMMABLE
CONTROL BITS
FROM VCO
TO PFD
21
datain
16 DATAIN
FRACTIONAL-N
DIVIDER D
MAX7049
Datain
FREQUENCY
WAVESHAPING
FUNCTION
wsoff
shpnn[7:0] : nn = 00:18
wsmlt[1:0]
tstep[7:0]
base[20:0] → SPACE FREQUENCY
base1[20:0] → MARK FREQUENCY
base[20:0]
Figure 16. Tx FSK Mode Programming
Datain
base1[20:0]
base[20:0]
shp05[7:0]
shp04[7:0]
tSTEP
tSTEP
Figure 17. Tx FSK Frequency Waveshaping Timing Diagram
�� Maxim Integrated Products 28
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
The 21-bit divider word is updated at a rate defined by
the tstep[7:0] bits, and this update time step is given by:
tSTEP = tstep[7:0]/mclk
In terms of the shpnn[7:0] bits, the value of base1[20:0]
is therefore:
base1[20:0] = base[20:0] +
nn = 18
∑
shpnn[7:0]
nn = 00
As Figure 17 illustrates, the frequency ramp-down shape
is the inverse, not the mirror image, of the frequency
ramp-up shape. The frequency deviation, which is the
difference between the mark frequency and the space
frequency, can also be expressed in terms of the
shpnn[7:0] bits:
frequency deviation = fXTAL /2 16 ×
nn = 18
∑
shpnn[7:0]
nn = 00
The waveshaping function allows for the approximation of
any monotonic-shape characteristic. An example of the
waveshaping function is the approximation of a 2kbps
NRZ with linear ramp shaping of duration at a 1/2 bit
interval and deviation of 50kHz. The length of the ramp
time is 250Fs. With a 3.2MHz mclk, a decimal value of
40 (0x28) is required for the tstep[7:0] SPI bits because
each of the time steps would need to be 12.5Fs, and 40
x 0.3125Fs yields 12.5Fs. This requires a decimal value
of 11 (0xB) for the shpnn[7:0] bits if used with a 16MHz
crystal. In this case the deviation is 19 (# of frequency
steps) x 11 (frequency change per step) x 16,000,000/216
or 51.03kHz. To attain a value closer to 50kHz at the
expense of linearity, four of the Shape00–Shape18
register values could have been set to decimal 10 (0xA).
This results in a deviation of 205 x 16,000,000/216 or
50.05kHz. The maximum programmable deviation (not
typically used with companion receivers due to bandwidth limitations) in this mode with a 16.0MHz crystal is
19 x 255 x 16,000,000/216 or 1.18MHz.
Tx Pulse FSK Mode
In this mode, the wsoff bit (TxConf0 register, 0x0C, bit 6)
is set and the wsmlt[1:0] bits (TxConf1 register, 0x0D,
bits 7:6) are used to transition directly from the space
frequency to the mark frequency without the use of
shaping. The value of base1[20:0] is expressed as:
base1[20:0] = base[20:0] + wsm × shp00[7:0]
where wsm is a multiplier whose value is given in Table 8.
This mode of pulsed FSK might offer slightly better range
when compared to shaped FSK at the expense of a higher
occupied bandwidth. A waveshaping function is also
available in Tx ASK mode. This feature is documented in
the Power Amplifier section.
Loop Bandwidth
The required loop bandwidth of the fractional-N synthesizer is dependent on the required phase noise characteristics of the transmitted carrier signals, the required
frequency settling times, the FSK modulation rates, and
the current consumption.
Three components dominate the phase noise of the
fractional-N synthesizer output: close-in phase noise, VCO
phase noise, and fractional quantization phase noise.
The loop bandwidth and filter order can be set to meet
the requirements for a wide range of applications due to
the low close-in phase noise (for excellent performance
at wide-loop bandwidths) and low VCO phase noise
(for excellent performance at narrow-loop bandwidths).
The loop filter order can be increased to lessen the
effect of fractional quantization phase noise for wide-loop
bandwidths if necessary.
Table 8. Tx FSK Pulse Mode Frequency Multiplier Values
wsmlt[1:0] TxConf1 REGISTER, ADDRESS 0x0D, BITS 7:6
wsm
00
1
01
2
10
4
11
8
�� Maxim Integrated Products 29
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
Generally, a 100kHz loop bandwidth works for most
applications. This choice allows for fast settling times,
within typically 48Fs for less than 5kHz offset during a
26MHz step in the 902MHz to 928MHz ISM band. This
loop bandwidth is near the optimum for minimizing the
contributions of both close-in phase noise and VCO
phase noise. In addition, this choice allows for FSK
modulation rates up to 160kbps NRZ and 80kbps
Manchester for most applications. If the phase noise at
higher offset frequencies needs to be reduced, the loop
bandwidth can be lowered to allow for the VCO noise to
dominate the phase-noise profile completely.
The loop filter components can be calculated as follows:
R = (2 x G x D x BW)/(ICP x KVCO)I
where:
R is the loop filter resistor in I.
D is the frequency division ratio of the feedback
divider of the fractional-N synthesizer.
BW is the desired fractional-N synthesizer loop bandwidth in Hz.
ICP is the charge-pump current in A.
KVCO is the VCO gain at the synthesizer output
frequency (863MHz to 945MHz) in Hz/V.
CL = (√10)/(2 x G x R x BW) in F
where:
CL is the large-loop filter capacitor in series with R.
The value of 10 is approximate.
CS = 1/(2 x G x R x BW x (√10) ) in F
where:
CS is the small-loop filter capacitor in parallel with the
series combination of R and CL.
R is the loop filter resistor in I.
BW is the desired fractional-N synthesizer loop bandwidth in Hz.
The value of 10 is approximate.
An additional RC pole can be added to the loop filter
to remove more fractional quantization phase noise at
wide-loop bandwidths. This pole is added between the
CPOUT pin and the CTRL pin. The resistance of the RC
pole should be 1.5x the value of the loop filter resistor to
limit loading while minimizing thermal noise as a phasenoise contributor. The pole frequency should be greater
than ten times the loop bandwidth. The loop filter configuration is shown in Figure 18.
Lock Detector
The primary support circuit for the fractional-N synthesizer is the lock detector. The internal lock-detect
signal is a gate for transmitter operation as illustrated in
the Operating Mode Overview section. The lock-detect
signal itself is adequate for most operating conditions,
but additional delay can be added if this signal is asserted too quickly, such that it does not allow the synthesizer
to settle to within the desired frequency accuracy as
illustrated in Figure 19.
R is the loop filter resistor in I.
BW is the desired fractional-N synthesizer loop bandwidth in Hz.
VDD
5
CP
6
CL
RP
R
CTRL
MAX7049
lockdet
VDD
7
CS
VCOVDD
CPVDD
plldel INTERVAL
CPOUT
8
plllock
SHORT RP AND CP IF EXTRA POLE IS NOT USED.
BYPASS VCOVDD AND CPVDD TO GROUND.
Figure 18. Synthesizer Loop Filter Topology
Figure 19. Lock Detector Delay Function
�� Maxim Integrated Products 30
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
The additional delay interval is set by the plldl[2:0] bits
(Conf1 register, 0x02, bits 5:3), and this delay is given by:
possible to the IC to minimize the capacitance on this node.
A temperature-stable, high-tolerance ±1% resistor is
recommended to minimize variations in output power. An
on-chip current multiplier of 25 x IR determines the LSB
of the PA bias DAC. For example, a 56.2kI resistor sets
the LSB to 0.5mA. The palopwr bit (TxConf0 register,
0x0C, bit 7) controls the bias current in the PA buffer
amplifier. When this bit is set, it lowers the buffer bias
current by 2mA for low-power applications. The buffer
amplifier sets the pedestal voltage (VP), which is required
for sufficient PA bias DAC headroom.
plldel interval = plldl[2:0] x (64/mclk)s
where plldl[2:0] is the decimal equivalent of the bits, yielding a norminal (3.2MHz mclk) plldel interval from 0 to 140Fs.
Both the lockdet and plllock status signals are available
on SDO, GPO1, and GPO2, as described in the Register
Details section for the TestBus0 and TestBus1 registers.
Power Amplifier
The IC contains a programmable current-drain, highefficiency power amplifier (PA). The PA is a differential
output stage capable of delivering more than +15dBm to
a 50I load including the losses of the matching network
and harmonic filter. The bias current for the PA (IPA) is
configurable in 64 linear steps, as illustrated in Figure 20.
The function of the matching network is to transform the
load resistance (RL) to the differential optimal PA load
resistance (ROPT). The value of ROPT is determined by
the desired output power (PD), the loss of the matching
network (Lm), the supply voltage (VDD), and the pedestal voltage (VP). Table 9 illustrates a design example for
determining ROPT and IPA_peak, where IPA_peak is the
peak value of the DC current.
An external resistor (REXT) is placed between the REXTPA
pin and ground. This resistor, along with an on-chip
reference voltage of 1.13V, sets the reference
current (IR). This resistor should be placed as close as
VDD
L
J
INSERTION LOSS
= Lm
SIGNAL SWINGS FOR
OPTIMAL LOAD
IMPEDANCE
MATCHING
NETWORK
FROM FREQUENCY
SYNTHESIZER
vi
BUFFER
AMP
RL
27
28
PA-
1.13V
REXT
2 REXTPA
IR
25x
I_lsb = 25 x IR
0
PA+
ROPT
MAX7049
PA+
VDD
VP
VP
palopwr
CURRENT MIRROR
vi
PA-
VP
PA BIAS DAC
IPA = (0:63) DIGITAL
CONTROL
x I_lsb
6
VDD
2 x (VDD - VP)
(PA+) - (PA-)
0
Figure 20. Power Amplifier Topology and Optimum Signal Swings
�� Maxim Integrated Products 31
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
The maximum efficiency of an ideal differential output
stage is 2/G and this must also be adjusted by the factor
(VDD - VP)/VDD to account for the headroom required
for the PA bias DAC current source. Note that an unbalanced differential impedance, as seen by the PA output
pins, causes different clipping levels for the PA+ pin
vs. the PA- pin. This degrades efficiency. In addition, if
the matching network does not transform the load resis-
tance to a differential impedance whose value is exactly
ROPT + j0, then this mismatch loss further degrades the
efficiency. In this PA design example, if the PA bias current
switched from zero to IPA_peak with the data input in ASK
mode, the occupied bandwidth of the modulated signal
would be significant. The IC includes an amplitude waveshaping function to reduce the occupied bandwidth of ASK
modulation.
Table 9. PA Design Example
PARAMETER
SYMBOL AND/OR EQUATION
EXAMPLE VALUE
VDD
3V
VP
0.5V
Supply Voltage
Pedestal Voltage
External PA Bias Resistance
REXT
56.2kI
I_lsb = 25 x 1.13/REXT
0.5mA
Desired Peak RF Output Power
PD
14dBm
Harmonic Filter and Composite
Matching/Combiner Network Loss
Lm
2dB
Actual PA RF Output Power
PPA = PL + Lm
16dBm
Actual PA RF Output Power
PPA_mW = 10(PPA/10)
40mW
Required PA DC Power
PDC = PPA_mW x G/2 x VDD/(VDD -VP)
75mW
Maximum PA Efficiency
Maximum efficiency = 100 x 2/G x (VDD - VP)/VDD
53%
Efficiency = 100 x 10(PD/10)/PDC
33%
Required Peak DC Current
IPA_peak = PDC/VDD
25mA
PA Code for Desired Power
idac_peak[5:0]
50 decimal (0x32)
PA Bias DAC LSB
Composite PA Efficiency (includes
Matching Network Loss)
FROM FREQUENCY
SYNTHESIZER
28
27
PA-
PA+
BUFFER
AMP
vi
idac[5:0]
datain
16 DATAIN
MAX7049
Datain
PROGRAMMABLE
CONTROL BITS
IPA = idac[5:0] x I_lsb
6
wsoff
AMPLITUDE
WAVESHAPING
FUNCTION
shpnn[7:0] : nn = 00:18
wsmlt[1:0]
tstep[7:0]
Figure 21. Tx ASK Mode Programming
�� Maxim Integrated Products 32
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
Tx ASK Mode Using Amplitude Waveshaping
The ASK waveshaping function is illustrated in Figure 21.
In this mode, the wsoff bit (TxConf0 register, 0x0C, bit 6)
is cleared and the wsmlt[1:0] bits (TxConf1 register,
0x0D, bits 7:6) are cleared. After txready is high, the PA
transitions from zero bias current to IPA_peak, on the
rising edge of the Datain signal. This transition occurs
in 20 discrete steps, determined by the tstep[7:0] bits
(TxTstep register, 0x0E, bits 7:0) and the shpnn[7:0] bits
(Shape00–Shape18 registers, 0x0F–0x21, bits 7:0, where
nn = 00 to 18), as shown in Figure 22.
The PA DAC word is updated at a rate defined by the
tstep[7:0] bits, and this update time step is given by:
tSTEP = tstep[7:0]/mclk
In terms of the shpnn[7:0] bits, the value of idac_peak[5:0]
is therefore:
.
idac_peak[5:0] =
nn = 18
∑
shpnn[7:0]
nn = 00
The two most-significant bits of shpnn[7:0] should always
be zero in ASK mode. As Figure 22 illustrates, the rampdown shape is the inverse of the ramp-up shape. The
waveshaping function allows for the approximation of
any monotonic shape characteristic. Since the shpnn
registers are 8 bits wide, the PA can be pulsed from zero
current to the maximum bias current in one time step if
desired.
An example is the approximation of a 4kbps NRZ with
linear ramp shaping of 1/2 bit interval duration and
peak PA bias current of 10mA using REXT = 56.2kI.
The length of the ramp time is 125Fs. With a 3.2MHz
mclk, this requires a decimal value of 20 (0x14) for the
tstep[7:0] because each of the 20 time steps would need
to be 6.25Fs, and 20 x 0.3125Fs yields 6.25Fs. This
requires a decimal value of 1 (0x1) for each Shape00–
Shape18 register. In this case, the peak PA bias current
is 19 x 25 x 1.13/56,200, or 9.55mA. To attain a value
closer to 10mA at the expense of linearity, one of the
Shape00–Shape18 register values could have been set
to decimal 2 (0x2). This results in a peak PA bias current
of 20 x 25 x 1.13/56,200, or 10.05mA.
Datain
idac_peak[5:0]
0
shp05[7:0]
shp04[7:0]
tSTEP
tSTEP
Figure 22. ASK Waveshaping Timing Diagram
�� Maxim Integrated Products 33
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
Tx FSK Mode Amplitude Ramp
In Tx FSK mode, the carrier is modulated by the
frequency-shaping function, as defined in the Fractional-N
Synthesizer section. This frequency waveshaping is
designed to minimize the occupied bandwidth of the
transmit signal in Tx FSK mode. However, the occupied
bandwidth might degrade if the PA turns on and off
abruptly at the beginning and end of a burst. A PA amplitude ramp feature is available in Tx FSK mode to prevent
the degradation of the occupied bandwidth. This feature
is illustrated in Figure 23.
After the IC is enabled and the txready signal transitions high, the PA bias current ramps up linearly to the
value fska[5:0] (TxConf0 register, 0x0C, bits 5:0) x I_lsb
in increments of fskas[5:0] (TxConf1 register, 0x0D, bits
5:0) x I_lsb, as illustrated in Figure 24.
Similarly, the PA bias current ramps down linearly on
the falling edge of the enable signal. Note that this PA
ramp feature is also automatically invoked when hopping
from one channel to another channel, as defined in the
Fractional-N Synthesizer section.
The PA DAC word is updated at a rate defined by the
tstep[7:0] bits, and this update time step is given by:
tSTEP = tstep[7:0]/mclk
To transmit the entire message at the desired power
level, the user should wait until the PA ramp is completed
before initiating the data sequence.
FROM FREQUENCY
SYNTHESIZER
28
27
PA-
PA+
BUFFER
AMP
vi
idac[5:0]
enable
17 ENABLE
MAX7049
Enable
PROGRAMMABLE
CONTROL BITS
IPA = idac[5:0] x I_lsb
6
fska[5:0]
AMPLITUDE
RAMP
FUNCTION
fskas[5:0]
tstep[7:0]
Figure 23. Tx FSK Amplitude Ramp Feature
�� Maxim Integrated Products 34
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
enable AND
txready
fska[5:0]
0
fskas[5:0]
fskas[5:0]
tSTEP
tSTEP
Figure 24. Tx FSK Amplitude Ramp Timing Diagram
Register Details
Table 10. Configuration Register Map
GROUP/FUNCTION
HEX
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
0
Ident
0x00
1
0
1
0
0
1
1
1
Conf0
0x01
—
—
—
mode
fsel_1
fsel_0
xtal_1
xtal_0
Conf1
0x02
icont
ibsel
plldl_2
plldl_1
plldl_0
—
—
—
IOConf0
0x03
gp1isht
gp2isht
ckdiv_1
ckdiv_0
gp2s_3
gp2s_2
gp2s_1
gp2s_0
IOConf1
0x04
sdos_3
sdos_2
sdos_1
sdos_0
gp1s_3
gp1s_2
gp1s_1
gp1s_0
IOConf2
0x05
—
—
gp1md_1
gp1md_0
clksht
gp2md_2
gp2md_1
gp2md_0
FBase0
0x08
—
—
—
base_20
base_19
base_18
base_17
base_16
FBase1
0x09
base_15
base_14
base_13
base_12
base_11
base_10
base_9
base_8
FBase2
0x0A
base_7
base_6
base_5
base_4
base_3
base_2
base_1
base_0
FLoad
0x0B
—
—
—
—
—
—
—
hop
TxConf0
0x0C
palopwr
wsoff
fska_5
fska_4
fska_3
fska_2
fska_1
fska_0
TxConf1
0x0D
wsmlt_1
wsmlt_0
fskas_5
fskas_4
fskas_3
fskas_2
fskas_1
fskas_0
TxTstep
0x0E
tstep_7
tstep_6
tstep_5
tstep_4
tstep_3
tstep_2
tstep_1
tstep_0
1
2
3
4
�� Maxim Integrated Products 35
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
Table 10. Configuration Register Map (continued)
GROUP/FUNCTION
5
6
7
HEX
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
Shape00
0x0F
shp00_7
shp00_6
shp00_5
shp00_4
shp00_3
shp00_2
shp00_1
shp00_0
Shape01
0x10
shp01_7
shp01_6
shp01_5
shp01_4
shp01_3
shp01_2
shp01_1
shp01_0
Shape02
0x11
shp02_7
shp02_6
shp02_5
shp02_4
shp02_3
shp02_2
shp02_1
shp02_0
Shape03
0x12
shp03_7
shp03_6
shp03_5
shp03_4
shp03_3
shp03_2
shp03_1
shp03_0
Shape04
0x13
shp04_7
shp04_6
shp04_5
shp04_4
shp04_3
shp04_2
shp04_1
shp04_0
Shape05
0x14
shp05_7
shp05_6
shp05_5
shp05_4
shp05_3
shp05_2
shp05_1
shp05_0
Shape06
0x15
shp06_7
shp06_6
shp06_5
shp06_4
shp06_3
shp06_2
shp06_1
shp06_0
Shape07
0x16
shp07_7
shp07_6
shp07_5
shp07_4
shp07_3
shp07_2
shp07_1
shp07_0
Shape08
0x17
shp08_7
shp08_6
shp08_5
shp08_4
shp08_3
shp08_2
shp08_1
shp08_0
Shape09
0x18
shp09_7
shp09_6
shp09_5
shp09_4
shp09_3
shp09_2
shp09_1
shp09_0
Shape10
0x19
shp10_7
shp10_6
shp10_5
shp10_4
shp10_3
shp10_2
shp10_1
shp10_0
Shape11
0x1A
shp11_7
shp11_6
shp11_5
shp11_4
shp11_3
shp11_2
shp11_1
shp11_0
Shape12
0x1B
shp12_7
shp12_6
shp12_5
shp12_4
shp12_3
shp12_2
shp12_1
shp12_0
Shape13
0x1C
shp13_7
shp13_6
shp13_5
shp13_4
shp13_3
shp13_2
shp13_1
shp13_0
Shape14
0x1D
shp14_7
shp14_6
shp14_5
shp14_4
shp14_3
shp14_2
shp14_1
shp14_0
Shape15
0x1E
shp15_7
shp15_6
shp15_5
shp15_4
shp15_3
shp15_2
shp15_1
shp15_0
Shape16
0x1F
shp16_7
shp16_6
shp16_5
shp16_4
shp16_3
shp16_2
shp16_1
shp16_0
Shape17
0x20
shp17_7
shp17_6
shp17_5
shp17_4
shp17_3
shp17_2
shp17_1
shp17_0
Shape18
0x21
shp18_7
shp18_6
shp18_5
shp18_4
shp18_3
shp18_2
shp18_1
shp18_0
TestMux
0x3C
—
—
—
—
tmux_3
tmux_2
tmux_1
tmux_0
Datain
0x3D
—
datain
—
—
—
—
—
—
EnableReg
0x3E
—
—
—
—
tsensor
—
—
enable
TestBus0
0x40
tbus_15
tbus_14
tbus_13
tbus_12
tbus_11
tbus_10
tbus_9
tbus_8
TestBus1
0x41
tbus_7
tbus_6
tbus_5
tbus_4
tbus_3
tbus_2
tbus_1
tbus_0
Status0
0x42
txready
—
adcrdy
—
gpo1out
plllock
lockdet
ckalive
Status1
0x43
—
—
—
tsdone
—
—
—
—
“—” Denotes a reserved bit. If a register contains reserved bits, write 0 to the reserved bit content.
Register 0x00 contents are always 0xA7, and can be used to identify the IC on the SPI bus.
Registers 0x40 through 0x43 are read-only registers, containing various states and status that can be read through the SPI.
�� Maxim Integrated Products 36
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
Detailed Register Descriptions
Table 11. Group 0: Identification Register (Ident)
GROUP/FUNCTION
HEX
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
0
0x00
1
0
1
0
0
1
1
1
Ident
Table 12. Ident Register (0x00)
BIT
NAME
7:0
ident[7:0]
FUNCTION
Read-only register used for identification purposes. The content of this register is always 0xA7.
Table 13. Group 1: General Configuration Registers (Conf0, Conf1)
GROUP/FUNCTION
1
HEX
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
Conf0
0x01
—
—
—
mode
fsel_1
fsel_0
xtal_1
xtal_0
Conf1
0x02
icont
ibsel
plldl_2
plldl_1
plldl_0
—
—
—
Table 14. Conf0 Register (0x01)
BIT
NAME
4
mode
FUNCTION
1-bit configuration for transmit mode:
0 = ASK
1 = FSK
2-bit configuration for LO division ratio:
3:2
fsel[1:0]
00
01
10
11
3
2
Not used
1
2-bit crystal divider configuration. Based on a typical crystal selection of 16.0MHz, 19.2MHz, or
22.4MHz, these bits are usually configured to yield a constant 3.2MHz mclk frequency for timing
control and driving characteristics of the digital section of the IC. For data rates up to 200kbps,
an mclk frequency of up to 4.0MHz is needed. The typical settings are:
1:0
xtal[1:0]
Crystal 16.0MHz
19.2MHz
22.4MHz
20.0MHz
xtal[1:0]
00 01 10 00 11 Divide
Divide
Divide
Divide
Divide
by
by
by
by
by
5
6
7
5
8
(16.0/5
(19.2/6
(22.4/7
(20.0/5
=
=
=
=
3.2MHz)
3.2MHz)
3.2MHz)
4.0MHz)
�� Maxim Integrated Products 37
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
Table 15. Conf1 Register (0x02)
BIT
NAME
FUNCTION
7
icont
Selects between low current (0 = 204FA) and high current (1 = 407FA) modes for the synthesizer
charge pump, allowing for lower noise operation with the expense of extra current.
6
ibsel
Selects between low VCO core current and high VCO core current (1 = additional 1mA) in the
synthesizer.
3-bit configuration for extra delay after lock-detect flag (lockdet) from the synthesizer is asserted
(assuming mclk = 3.2MHz):
5-3
plldl[2:0]
plldl[2:0] delay(Fs)
000 0
001 20
010 40
011 60
100 80
101 100
110 120
111 140
After this delay, an internal signal called plllock is asserted high to determine the digital lock flag
for the synthesizer.
Table 16. Group 2: GPO, Data Output, and Clock Output Registers
(IOConf0, IOConf1, IOConf2)
GROUP/FUNCTION
2
HEX
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
IOConf0
0x03
gp1isht
gp2isht
ckdiv_1
ckdiv_0
gp2s_3
gp2s_2
gps2_1
gps2_0
IOConf1
0x04
sdos_3
sdos_2
sdos_1
sdos_0
gp1s_3
gp1s_2
gp1s_1
gp1s_0
IOConf2
0x05
—
—
gp1md_1
gp1md_0
clksht
gp2md_2
gp2md_1
gp2md_0
�� Maxim Integrated Products 38
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
Table 17. IOConf0 Register (0x03)
BIT
NAME
FUNCTION
7
gp1isht
GPO1 current mode during sleep. If the IC GPO1 is configured to current drive mode (IOConf2
register, 0x05), writing 1 to this bit allows for the current mode operation even if the IC is in Sleep
mode or disabled. If this bit is 0, current mode operation is only active when the IC is enabled.
6
gp2isht
GPO2 current mode during sleep. If the IC GPO2 is configured to current drive mode (IOConf2
register, 0x05), writing 1 to this bit allows for the current mode operation even if the IC is in Sleep
mode or disabled. If this bit is 0, current mode operation is only active when the IC is enabled.
2-bit configuration for clock output divider setting. A clock source selected by gp2s[3:0] is divided by
the settings in these bits, according to the following:
5:4
ckdiv[1:0]
ckdiv[1:0] 00 01 10 11 Divide by
1
2
4
8
4-bit configuration for GPO2 signal selection:
3:0
gp2s[3:0]
gp2s[3:0] 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1011 1100 1101 1110 1111 Output
plllock
mclk/(ckdiv divider)
xtal/(ckdiv divider)
xtal/16/(ckdiv divider)
tbus[4]
tbus[5]
tbus[6]
tbus[7]
tbus[8]
tbus[9]
tbus[10]
tbus[11]
tbus[12]
tbus[14]
tbus[15]
where:
mclk is the master digital clock generated from the crystal divider block (xtal[1:0]);
xtal is the crystal oscillator output clock;
xtal/16 is a divided-by-16 version of the crystal oscillator frequency;
tbus[15:0] is the 16-bit bus selected by tmux[3:0] (TestMux register, 0x3C, bits 3:0).
�� Maxim Integrated Products 39
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
Table 18. Register IOConf1 (0x04)
BIT
NAME
FUNCTION
4-bit SPI data output GPO mode selection. When CS is low, the SDO pin outputs the SPI data output,
as described in the Serial Peripheral Interface (SPI) section. When CS is high, the SDO acts as a third
GPO, according to:
7:4
sdos[3:0]
CS sdos[3] sdos[2] sdos[1]
0
x
x
x
1
0
0
0
1
0
0
0
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
1
1
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
1
1
0
1
1
1
1
0
1
1
1
0
1
1
1
1
1
1
1
1
sdos[0] output
x
SPI_Dout
0
tbus[ 0]
1
tbus[ 1]
0
tbus[ 2]
1
tbus[ 3]
0
tbus[ 4]
1
tbus[ 5]
0
tbus[ 6]
1
tbus[ 7]
0
tbus[ 8]
1
tbus[ 9]
0
tbus[10]
1
tbus[11]
0
tbus[12]
1
tbus[13]
0
tbus[14]
1
tbus[15]
tbus[15:0] is the 16-bit bus selected by tmux[3:0] (TestMux register, 0x3C, bits 3:0).
4-bit configuration for GPO1 signal selection:
3:0
gp1s[3:0]
gp1s[3] 0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
gp1s[2] 0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
gp1s[1] 0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
gp1s[0] 0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
output
tbus[ 0]
tbus[ 1]
tbus[ 2]
tbus[ 3]
tbus[ 4]
tbus[ 5]
tbus[ 6]
tbus[ 7]
tbus[ 8]
tbus[ 9]
tbus[10]
tbus[11]
tbus[12]
tbus[13]
tbus[14]
tbus[15]
tbus[15:0] is the 16-bit bus selected by tmux[3:0] (TestMux register, 0x3C, bits 3:0).
�� Maxim Integrated Products 40
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
Table 19. Register IOConf2 (0x05)
BIT
NAME
FUNCTION
2-bit
5:4
gp1md[1:0]
3
clksht
0x
10
11
GPO1 mode selection:
buffer mode
80FA current mode
160FA current mode
Enable (1) or disable (0) clock output on GPO2 during sleep.
3-bit GPO2 mode selection. The GPO2 can provide a high-frequency clock output, and therefore its
current capability is higher.
2:0
gp2md[2:0]
0xx
100
101 110
111
buffer mode
1.0mA
2.0mA
3.0mA
4.0mA
Table 20. Group 3: Synthesizer Frequency Settings (FBase0, FBase1, FBase2, FLoad)
GROUP/FUNCTION
3
HEX
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
FBase0
0x08
—
—
—
base_20
base_19
base_18
base_17
base_16
FBase1
0x09
base_15
base_14
base_13
base_12
base_11
base_10
base_9
base_8
FBase2
0x0A
base_7
base_6
base_5
base_4
base_3
base_2
base_1
base_0
FLoad
0x0B
—
—
—
—
—
—
—
hop
Registers 0x08, 0x09, and 0x0A set the 21-bit base value for the control of the synthesizer frequency. Bits 20:16 form
the 5-bit integer part (base[20:16]), and bits 15:0 form the 16-bit fractional part (base[15:0]).
The synthesizer frequency is then given by:
fSYNTH = fXTAL x (32 + base[20:0]/65,536)
where fXTAL is the crystal frequency in MHz. The synthesizer frequency is then divided according to the fsel[1:0]
settings (Conf0 register, 0x01, bits 3:2) to generate the LO frequency:
Table 21. Synthesizer Divider Settings
fsel[1:0]
LO DIVIDER
00
3
01
2
11
1
�� Maxim Integrated Products 41
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
The synthesizer frequency range is from 863MHz to 945MHz, which translates to the base[20:0] values shown in Table 22.
Table 22. Synthesizer Programming Values
CRYSTAL (MHz)
16.0
19.2
22.4
20
SYNTHF (MHz)
MULTIPLIER FACTOR (dec)
base[20:0]
863
21.9375
0x15F000
945
27.0625
0x1B1000
863
12.9479
0x0CF2AB
945
17.2188
0x113800
863
6.5268
0x0686DB
945
10.1875
0x0A3000
863
11.1500
0x0B2666
945
15.2500
0x0F4000
The minimum and maximum frequency for each band is shown in Table 23.
Table 23. Frequency Ranges
SYNTHF (MHz)
300MHz (fsel = 00)
450MHz (fsel = 01)
900MHz (fsel = 11)
863
287.70
431.50
863.00
945
315.00
472.50
945.00
The hop bit allows for a parallel load of the three FBase registers. This is a self-reset bit that reverts to 0 when the operation is completed. This function can also be accomplished by use of the external HOP pin. A detailed description of the
hop operation can be found in the appropriate sections of the transmitter detailed operations descriptions.
Table 24. FBase0 Register (0x08)
BIT
NAME
4:0
base[20:16]
FUNCTION
5-bit integer value for synthesizer.
Table 25. FBase1 Register (0x09)
BIT
NAME
7:0
base[15:8]
FUNCTION
8 MSBs of fractional value for synthesizer.
Table 26. FBase2 Register (0x0A)
BIT
NAME
7:0
base[7:0]
FUNCTION
8 LSBs of fractional value for synthesizer.
Table 27. FLoad (0x0B)
BIT
NAME
0
hop
FUNCTION
Hop bit. Loads the synthesizer fractional-N divider base value to base[20:0] written in registers
8 through 10. This is a self-reset bit, and is reset to zero after the operation is completed.
�� Maxim Integrated Products 42
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
Table 28. Group 4: Transmiter Amplitude and Timing Parameters
(TxConf0, TxConf1, TxTstep)
GROUP/FUNCTION
4
HEX
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
TxConf0
0x0C
palopwr
wsoff
fska_5
fska_4
fska_3
fska_2
fska_1
fska_0
TxConf1
0x0D
wsmlt_1
wsmlt_0
fskas_5
fskas_4
fskas_3
fskas_2
fskas_1
fskas_0
TxTstep
0x0E
tstep_7
tstep_6
tstep_5
tstep_4
tstep_3
tstep_2
tstep_1
tstep_0
These registers set general FSK/ASK parameters for PA amplitude and rate control (FSK), shaping control, and the step
control used for amplitude or frequency shaping.
Table 29. TxConf0 Register (0x0C)
BIT
NAME
7
palopwr
6
wsoff
5:0
fska[5:0]
FUNCTION
Reduces the PA input buffer current by 2mA when set to 1. Useful at low output power levels.
Disables (1) or enables (0) waveshaping. If waveshaping is disabled, only shp00[7:0] (Shape00
register, 0x0F) and wsmlt[1:0] (TxConf1 register, 0x0D) are used to set the amplitude (ASK) or
frequency (FSK) deviation.
6-bit final value for FSK PA amplitude (bias current) control.
Table 30. TxConf1 Register (0x0D)
BIT
NAME
FUNCTION
2-bit scaler for shp00[7:0] (Shape00 register, 0x0F), effectively multiplying the value of Shape00 by:
7:6
wsmlt[1:0]
5:0
fskas[5:0]
wsmlt[1:0] multiplier
00
1
01
2
10
4
11
8
6-bit FSK amplitude (bias current) step for ramp-up and ramp-down operations. The PA amplitude
increases/decreases by this amount for every 1/20th of the data rate time elapsed (TxTstep register,
0x0E), until it reaches the final fska[5:0] value when ramping up, or reaches 0 when ramping down.
Table 31. TxTstep Register (0x0E)
BIT
NAME
FUNCTION
8-bit update value for waveshaping. This setting corresponds to 1/20th of the data rate, given in
periods of the master digital clock (312.5ns for 3.2 MHz).
tstep[7:0] = INT (mclk/(20 x DataRate))
7:0
tstep[7:0]
For 80kbps < DataRate P 160kbps, tstep[7:0] = 1, mclk = 3.2MHz
For 40kbps < DataRate P 80kbps, tstep[7:0] = 2, mclk = 3.2MHz
For 160kbps < DataRate P 200kbps, tstep[7:0] = 1, mclk = 4.0MHz
For 4kbps, tstep = INT (3.2 x106/(20 x 4000)) = 40 (0x28), mclk = 3.2MHz
The maximum value for tstep[7:0] is 255, which allows for a minimum shaped data rate of 627bps.
These values assume shaping during the entire bit interval. The tstep value can be set lower if
possible for shaping during a portion of the bit interval.
This setting allows for the 20 sequential steps in either the amplitude (ASK) or frequency (FSK) waveshaping process,
for each symbol of the transmitted data.
�� Maxim Integrated Products 43
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
Table 32. Group 5: Transmitter Shaping Registers (Shape00–Shape18)
GROUP/FUNCTION
5
HEX
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
Shape00
0x0F
shp00_7
shp00_6
shp00_5
shp00_4
shp00_3
shp00_2
shp00_1
shp00_0
Shape01
0x10
shp01_7
shp01_6
shp01_5
shp01_4
shp01_3
shp01_2
shp01_1
shp01_0
Shape02
0x11
shp02_7
shp02_6
shp02_5
shp02_4
shp02_3
shp02_2
shp02_1
shp02_0
Shape03
0x12
shp03_7
shp03_6
shp03_5
shp03_4
shp03_3
shp03_2
shp03_1
shp03_0
Shape04
0x13
shp04_7
shp04_6
shp04_5
shp04_4
shp04_3
shp04_2
shp04_1
shp04_0
Shape05
0x14
shp05_7
shp05_6
shp05_5
shp05_4
shp05_3
shp05_2
shp05_1
shp05_0
Shape06
0x15
shp06_7
shp06_6
shp06_5
shp06_4
shp06_3
shp06_2
shp06_1
shp06_0
Shape07
0x16
shp07_7
shp07_6
shp07_5
shp07_4
shp07_3
shp07_2
shp07_1
shp07_0
Shape08
0x17
shp08_7
shp08_6
shp08_5
shp08_4
shp08_3
shp08_2
shp08_1
shp08_0
Shape09
0x18
shp09_7
shp09_6
shp09_5
shp09_4
shp09_3
shp09_2
shp09_1
shp09_0
Shape10
0x19
shp10_7
shp10_6
shp10_5
shp10_4
shp10_3
shp10_2
shp10_1
shp10_0
Shape11
0x1A
shp11_7
shp11_6
shp11_5
shp11_4
shp11_3
shp11_2
shp11_1
shp11_0
Shape12
0x1B
shp12_7
shp12_6
shp12_5
shp12_4
shp12_3
shp12_2
shp12_1
shp12_0
Shape13
0x1C
shp13_7
shp13_6
shp13_5
shp13_4
shp13_3
shp13_2
shp13_1
shp13_0
Shape14
0x1D
shp14_7
shp14_6
shp14_5
shp14_4
shp14_3
shp14_2
shp14_1
shp14_0
Shape15
0x1E
shp15_7
shp15_6
shp15_5
shp15_4
shp15_3
shp15_2
shp15_1
shp15_0
Shape16
0x1F
shp16_7
shp16_6
shp16_5
shp16_4
shp16_3
shp16_2
shp16_1
shp16_0
Shape17
0x20
shp17_7
shp17_6
shp17_5
shp17_4
shp17_3
shp17_2
shp17_1
shp17_0
Shape18
0x21
shp18_7
shp18_6
shp18_5
shp18_4
shp18_3
shp18_2
shp18_1
shp18_0
These registers set the amplitude (ASK) or frequency deviation (FSK) modulated by the incoming transmitted data.
For every 1/20th of the bit rate defined by tstep[7:0], the following shape value is added to the previous accumulated
result. All the shape values are deltas, and the final ASK amplitude or FSK deviation is given by the cumulative sum of
all the shape registers.
In ASK, the initial value is 0. For FSK, the initial value is given by base[20:0]. There are 20 intervals (hence 19 shape
registers) that are added on the 0-1 transition of the transmitted data or subtracted from on the 1-0 transition.
Table 33. Shape00 Register (0x0F)
BIT
7:0
NAME
shp00[7:0]
FUNCTION
First 8-bit value for waveshaping. This value is effectively multiplied by the wsmlt[1:0] setting
(TxConf1 register, 0x0D). If the wsoff bit is high, this is the only value that is added or subtracted to
perform either amplitude (ASK) or frequency (FSK) modulation.
�� Maxim Integrated Products 44
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
Table 34. Shape01–Shape18 Registers (0x10–0x21)
BIT
NAME
7:0
shp01[7:0]
shp02[7:0]
shp03[7:0]
shp04[7:0]
shp05[7:0]
shp06[7:0]
shp07[7:0]
shp08[7:0]
shp09[7:0]
shp10[7:0]
shp11[7:0]
shp12[7:0]
shp13[7:0]
shp14[7:0]
shp15[7:0]
shp16[7:0]
shp17[7:0]
shp18[7:0]
FUNCTION
18 8-bit values for waveshaping. These values, along with shp00[7:0], yield the 19 different values
(20 intervals) used for waveshaping, one for each of the 20 updates occurring during each 0-1 or
1-0 transmitted data transition.
Table 35. Group 6: Control Registers (TestMux, Datain, EnableReg)
GROUP/FUNCTION
6
HEX
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
TestMux
0x3C
—
—
—
—
tmux_3
tmux_2
tmux_1
tmux_0
Datain
0x3D
—
datain
—
—
—
—
—
—
EnableReg
0x3E
—
—
—
—
tsensor
—
—
enable
This register group combines status bus control (tbus[15:0]), GPO controls, temperature sensor control, register control
of pin function (txdata), and enable controls.
Table 36. TestMux Register (0x3C)
BIT
NAME
3:0
tmux[3:0]
FUNCTION
4-bit selection of tbus[15:0] (TestBus0 and TestBus1 registers, 0x40 and 0x41) contents. See the
TestBus0 and TestBus1 register descriptions for a complete description of what can be observed
through this 16-bit bus.
�� Maxim Integrated Products 45
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
Table 37. Datain Register (0x3D)
BIT
6
NAME
FUNCTION
datain
Transmit datain bit. This is a register equivalent of the DATAIN pin. When either the DATAIN pin or datain bit is 1,
the transmit data is 1. Only when both are 0 the transmit data is 0 (logical OR function). Keep 0 if only the external DATAIN pin is used, and keep DATAIN pin 0 if the internal datain bit is used.
Table 38. EnableReg Register (0x3E)
BIT
3
0
NAME
FUNCTION
tsensor
Writing a 1 to this bit starts the temperature sensor A/D conversion. This is a self-reset bit, where the
bit is automatically reset when the conversion is finished. The result can then be read through the
TestBus1 register (0x41). This function is available only in Sleep mode.
enable
Enables (1) or disables (0) the IC’s transmitter operations. To enable the IC, SHDN must be driven low. This is a
register equivalent of the ENABLE pin. When either the ENABLE pin or enable bit is 1, the IC transmit operation
is enabled. Only when both are 0 the transmitter is disabled (logical-OR function). Keep 0 if only the external
ENABLE pin is used, and keep ENABLE pin 0 if the internal enable is used.
Table 39. Group 7: Read-Only Status Registers (TestBus0, TestBus1, Status0, Status1)
GROUP/FUNCTION
7
HEX
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
TestBus0
0x40
tbus_15
tbus_14
tbus_13
tbus_12
tbus_11
tbus_10
tbus_9
tbus_8
TestBus1
0x41
tbus_7
tbus_6
tbus_5
tbus_4
tbus_3
tbus_2
tbus_1
tbus_0
Status0
0x42
txready
—
adcrdy
—
gpo1out
plllock
lockdet
ckalive
Status1
0x43
—
—
—
tsdone
—
—
—
—
Registers 0x3F–0x43 are read-only registers used for A/D results, status, and test.
Table 40. TestBus0 Register (0x40)
BIT
NAME
FUNCTION
7:0
tbus[15:8]
8 MSBs of the internal 16-bit bus tbus[15:0], selected by tmux[3:0] (TextMux register, 0x3C, bits 3:0).
�� Maxim Integrated Products 46
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
Table 41. Test Bus Signals (tbus[15:8])
tmux[3:0]
tbus[15]
tbus[14]
tbus[13]
tbus[12]
tbus[11]
tbus[10]
tbus[9]
tbus[8]
0x0
—
—
—
—
—
—
—
—
0x1
—
—
—
—
—
—
—
—
0x2
—
—
—
—
—
—
—
—
0x3
—
—
—
—
—
—
—
—
0x4
—
—
—
—
—
—
—
—
0x5
—
—
pabia[5]
pabia[4]
pabia[3]
pabia[2]
pabia[1]
pabia[0]
0x6
frac[15]
frac[14]
frac[13]
frac[12]
frac[11]
frac[10]
frac[9]
frac[8]
0x7
—
—
—
—
—
—
—
—
0x8
—
—
—
—
—
—
—
—
0x9
—
—
—
—
—
—
—
—
0xA
—
—
—
—
—
—
—
—
0xB
—
—
—
—
—
—
—
mclk
0xC
—
—
—
—
—
—
—
plllock
0xD
—
—
—
—
—
—
—
—
0xE
—
—
—
—
—
—
—
—
0xF
—
—
—
—
—
—
—
—
where:
tmux[3:0]
Signal
Description
0x0–0x4
—
Reserved signals for test purposes
0x5
pabia[5:0]
PA amplitude control bus
0x6
frac[15:8]
MSBs of fractional value sent to frequency synthesizer
0x7–0xA
—
Reserved signals for test purposes
0xB
mclk
Master digital clock
0xC
plllock
Synthesizer lock signal
0xD–0xF
—
Reserved signals for test purposes
Table 42. TestBus1 Register (0x41)
BIT
NAME
FUNCTION
7:0
tbus[7:0]
8 LSBs of the internal 16-bit bus tbus[15:0], selected by tmux[3:0] (TestMux register, 0x3C, bits 3:0).
�� Maxim Integrated Products 47
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
Table 43. Test Bus Signals (tbus[7:0])
tmux[3:0]
tbus[7]
tbus[6]
tbus[5]
tbus[4]
tbus[3]
tbus[2]
tbus[1]
tbus[0]
0x0
tsdonef
tsadc[6]
tsadc[5]
tsadc[4]
tsadc[3]
tsadc[2]
tsadc[1]
tsadc[0]
0x1
—
—
—
—
—
—
—
—
0x2
—
—
—
—
—
—
—
—
0x3
—
—
—
—
—
—
—
—
0x4
—
—
—
—
—
—
—
—
0x5
palopwr
—
—
integ[4]
integ[3]
integ[2]
integ[1]
integ[0]
0x6
frac[7]
frac[6]
frac[5]
frac[4]
frac[3]
frac[2]
frac[1]
frac[0]
—
0x7
—
—
—
—
—
—
—
0x8
—
—
—
—
—
—
—
—
0x9
—
—
—
ents
—
—
—
tsdonef
0xA
—
—
—
—
—
—
—
—
0xB
—
—
—
—
—
—
—
—
0xC
—
lockdet
ckalive
—
—
—
txready
—
0xD
—
—
—
—
—
—
—
—
0xE
—
—
—
—
—
—
—
—
0xF
—
—
—
—
mclk
—
—
—
where:
tmux[3:0]
Signal
Description
0x0
tsdonef
Temperature sensor conversion done flag
tsadc[6:0]
Temperature sensor A/D result
0x1–0x4
—
Reserved signals for test purposes
0x5
palopwr
PA low-power mode flag
integ[4:0]
Integer value sent to frequency synthesizer
0x6
frac[7:0]
LSBs of fractional value sent to frequency synthesizer
0x7, 0x8
—
Reserved signals for test purposes
0x9
ents
Enable temperature sensor conversion signal
tsdonef
Temperature sensor done flag
0xA, 0xB
—
Reserved signals for test purposes
0xC
lockdet
Synthesizer lock-detect signal
ckalive
Crystal oscillator clock alive flag
txready
Tx ready flag
0xD, 0xE
—
Reserved signals for test purposes
0xF
mclk
Master digital clock
Note that each of the signals available on the digital test bus can be observed on GPO1, GPO2, or SDO, as discussed
in the Digital Outputs section.
�� Maxim Integrated Products 48
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
Table 44. Status0 Register (0x42)
BIT
NAME
FUNCTION
7
txready
Transmit ready flag. After this bit goes to 1, the IC is ready to accept transitions on the DATAIN pin
or on the datain bit inputs. Both these bits should be 0 before the txready flag is 1.
5
adcrdy
Internal test flag that signals the end of the A/D warmup time.
3
gpo1out
Register copy of the GPO1 pin logical state.
2
plllock
Synthesizer lock flag, after programmable plldl[2:0] expires.
1
lockdet
Synthesizer lock detect flag.
0
ckalive
Crystal oscillator clock alive flag, indicating clock activity from the crystal oscillator.
Table 45. Status1 Register (0x43)
BIT
4
NAME
tsdone
FUNCTION
Temperature sensor conversion done flag. When 1, the A/D conversion of the internal temperature
sensor is completed.
Layout Considerations
A properly designed PCB is an essential part of any RF/
microwave circuit. On high-frequency, high-impedance
inputs and outputs, use minimum width lines and keep
them as short as possible to minimize stray capacitance.
Keeping the traces short also reduces parasitic inductance. Generally, 1in of PCB trace adds approximately
20nH of parasitic inductance. The parasitic inductance
can have a dramatic effect on the effective inductance
of a passive component. For example, a 0.5in trace
connecting to a 100nH inductor adds an extra 10nH of
inductance, or 10%.
To reduce parasitic inductance, use a solid ground
plane below the signal traces. Also, use low-inductance
connections to the ground plane for shunt matching and
bypassing components, and place bypassing capacitors
as close as possible to all power-supply pins. Use separate vias to the ground plane for all shunt matching and
bypassing components to reduce unwanted common
impedance coupling.
�� Maxim Integrated Products 49
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
Ordering Information
PART
MAX7049ATI+
TEMP RANGE
PIN-PACKAGE
-40NC to +125NC
28 TQFN-EP*
+Denotes a lead(Pb)-free/RoHS-compliant package.
*EP = Exposed pad.
Chip Information
PROCESS: BiCMOS
Package Information
For the latest package outline information and land patterns
(footprints), go to www.maxim-ic.com/packages. Note that a
“+”, “#”, or “-” in the package code indicates RoHS status only.
Package drawings may show a different suffix character, but
the drawing pertains to the package regardless of RoHS status.
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE NO.
LAND
PATTERN NO.
28 TQFN-EP
T2855+3
21-0140
90-0023
�� Maxim Integrated Products 50
MAX7049
High-Performance, 288MHz to 945MHz
ASK /FSK ISM Transmitter
Revision History
REVISION
NUMBER
REVISION
DATE
0
6/11
DESCRIPTION
Initial release
PAGES
CHANGED
—
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied.
Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical
Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2011
Maxim Integrated Products 51
Maxim is a registered trademark of Maxim Integrated Products, Inc.

Open as PDF

Similar pages: MAXIM MAX7060_12; AD AD9870EB; AD EVAL-ADF7021DB; AD ADF7020-1BCPZ-RL; TI CC2400-RTB1; TI CC1021RUZ; AD AD9146; ETC MAX7049; AMSCO NSE-5310; Datasheet; MAXIM MAX2652EUB; MICREL MICRF113_11; AMSCO NSE-5310; ETC WU106; XPPOWER WU400; TZ0151A _Rev 2.0_.pdf; SAMSUNG S1T8513A02-V0B0; SAMSUNG DS_S1T8515A01