MAXIM MAX7060_12

19-5096; Rev 1; 3/12
TION KIT
EVALUA BLE
IL
AVA A
280MHz to 450MHz Programmable
ASK/FSK Transmitter
The MAX7060 frequency and power-programmable
ASK/FSK transmitter operates at 280MHz to 450MHz
frequencies. This device incorporates a fully integrated
fractional-N synthesizer, which allows the user to set the
RF operating frequency to a large fraction of the 280MHz
to 450MHz frequency range with a single crystal. For
example, the MAX7060 can be tuned from 285MHz to
420MHz with a 15MHz crystal. The RF output power is
user-controlled between +14dBm and -14dBm, with a
5V supply or with battery voltages as low as 3.2V. At the
minimum specified battery voltage of 2.1V, the RF output
power-control range is between +10dBm and -14dBm.
To maintain a good output power match across a broad
range of frequencies, the MAX7060 also contains a programmable matching capacitor connected in parallel
with the power amplifier (PA) output.
ASK modulation is accomplished by switching the PA
on and off, so excellent modulation (on/off) ratios are
achieved. ASK amplitude shaping is available to reduce
the width of the transmission spectrum. FSK modulation is accomplished by changing the coefficients of
the high-resolution fractional-N synthesizer, so FSK
deviation is extremely accurate. Data rates up to 50kbps
Manchester coded for ASK and 70kbps Manchester
coded for FSK can be maintained while still satisfying
regulatory emission-bandwidth standards. The full set of
configuration functions are handled by an on-chip serial
peripheral interface (SPI). There is also a manual mode
where a limited number of settings can be made directly
through selected pins.
The startup time is very short, and data can be transmitted 250Fs after the enable command. The MAX7060
operates from a 2.1V to 3.6V supply, or internal regulators can be used for supply voltages between 4.5V and
5.5V. The standby current in the 3V mode is 400nA at
room temperature, and can be reduced to 5nA using the
low-power shutdown (LSHDN) pin.
The MAX7060 is available in a 24-pin (4mm x 4mm) thin
QFN package and is specified for the automotive temperature range from -40NC to +125NC.
Features
S Fully Integrated, Fast Fractional-N PLL
280MHz to 450MHz RF Frequency
Frequency Range 100% Tested at +125NC
< 250µs Startup Time
Adjustable FSK Mark and Space Frequencies
Ultra-Clean FSK Modulation
50kbps Manchester Data Rate ASK
70kbps Manchester Data Rate FSK
S Programmable Power Amplifier
+14dBm Tx Power with 5V Supply
+10dBm Tx Power at 2.1V Supply
28dB Power-Control Range in 1dB Steps
S Tunable PA Matching Capacitor
S Control Through SPI or Manual Settings
S Low Shutdown Current for 2.1V to 3.6V Supply
400nA Standby Current, Power-On-Reset
(POR) Active
5nA Shutdown Current, POR Inactive
S Supply Flexibility
2.1V to 3.6V Single-Supply Operation or
4.5V to 5.5V Supply Operation with Internal
Regulators
S 24-Pin (4mm x 4mm) TQFN Package
S FCC Part 15, ETSI EN 300 220 Compliant*
*ETSI compliance up to +6dBm EIRP.
Applications
Garage-Door Openers
Remote Controls
Home and Industrial Automation
Sensor Networks
Security Systems
Ordering Information
TEMP RANGE
PIN-PACKAGE
MAX7060ATG+
PART
-40NC to +125NC
24 TQFN-EP*
MAX7060ATG/V+
-40NC to +125NC
24 TQFN-EP*
+Denotes a lead(Pb)-free/RoHS-compliant package.
/V denotes an automotive qualified part.
*EP = Exposed pad.
________________________________________________________________ Maxim Integrated Products 1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
MAX7060
General Description
MAX7060
280MHz to 450MHz Programmable
ASK/FSK Transmitter
ABSOLUTE MAXIMUM RATINGS
GPOVDD, VDD5 to GND.......................................-0.3V to +6.0V
DVDD, PAVDD, and AVDD to GND......................-0.3V to +4.0V
ENABLE, SCLK_PWR0, SDI_PWR1, DIN,
CS_DEV, LSHDN, FREQ0, FREQ1, FREQ2, GPO1,
and GPO2_MOD to GND......................-0.3V to (VDD5 + 0.3V)
PAOUT, ROUT,
and PAVOUT to GND ....................... -0.3V to (VPAVDD + 0.3V)
XTAL1 and XTAL2 to GND.................... -0.3V to (VAVDD + 0.3V)
Continuous Power Dissipation (TA = +70NC)
24-Pin Thin QFN
(derate 20.8mW/NC above +70NC)..........................1666.7mW
Operating Temperature Range......................... -40NC to +125NC
Storage Temperature Range............................. -60NC to +150NC
Lead Temperature (soldering, 10s) ................................+300NC
Soldering Temperature (reflow).......................................+260NC
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS (5V OPERATION)
(Typical Application Circuit, 50I system impedance, tuned for 315MHz to 434MHz operation. VDD5 = VGPOVDD = 4.5V to 5.5V, fRF =
280MHz to 450MHz, fXTAL = 15MHz to 16MHz, TA = -40NC to +125NC, unless otherwise noted. Typical values are at VDD5 = VGPOVDD
= +5V, TA = +25NC, PA matched for optimum output power, unless otherwise noted. All min and max values are 100% tested at TA
= +125NC and guaranteed by design and characterization over temperature, unless otherwise noted.)
PARAMETER
Supply Voltage
Regulated Analog Supply
Voltage
SYMBOL
CONDITIONS
VDD
MAX
UNITS
5
5.5
V
3.2
PLL on, PA on, data
at 50% duty cycle
(ASK), +10dBm
(PApwr = 0x19)
output power
(Notes 1, 2)
IDD
PLL on, PA on, data
at 100% duty cycle,
+10dBm (PApwr =
0x19) output power
(Note 1)
PLL on, PA on, data
at 100% duty cycle,
max (PApwr = 0x1E)
output power
(Note 1)
Standby Current
TYP
4.5
AVDD
PLL on, PA off
Active Supply Current
MIN
ISTDBY
VENABLE < VIL,
VLSHDN < VIL
V
fRF = 315MHz
4.7
6.0
fRF = 433.92MHz
5.3
6.9
fRF = 315MHz
12.5
fRF = 433.92MHz
14.2
fRF = 315MHz
19
26
fRF = 433.92MHz
25
31.6
fRF = 315MHz
28
fRF = 433.92MHz
34
TA = +25NC
1.1
TA = +85NC
1.3
TA = +125NC
3.8
mA
FA
6.1
DIGITAL I/O
Input High Threshold
VIH
Input Low Threshold
VIL
0.9 x
VDVDD
2 _______________________________________________________________________________________
V
0.1 x
VDVDD
V
280MHz to 450MHz Programmable
ASK/FSK Transmitter
(Typical Application Circuit, 50I system impedance, tuned for 315MHz to 434MHz operation. VDD5 = VGPOVDD = 4.5V to 5.5V, fRF =
280MHz to 450MHz, fXTAL = 15MHz to 16MHz, TA = -40NC to +125NC, unless otherwise noted. Typical values are at VDD5 = VGPOVDD
= +5V, TA = +25NC, PA matched for optimum output power, unless otherwise noted. All min and max values are 100% tested at TA
= +125NC and guaranteed by design and characterization over temperature, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Input Pulldown Sink Current
IIH
6
FA
Input Pullup Source Current
IIL
5
FA
Output-Voltage High
Output-Voltage Low
VOH
VOL
ISINK = 100FA (GPO1 and GPO2_MOD,
gp1bst bit = 0)
VGPOVDD
- 0.10
ISINK = 200FA (GPO1), boost = on
(gp1bst bit = 1)
VGPOVDD
- 0.14
ISOURCE = 100FA (GPO1 and
GPO2_MOD, gp1bst bit = 0)
0.10
ISOURCE = 200FA (GPO1), boost = on
(gp1bst bit = 1)
0.14
V
V
DC ELECTRICAL CHARACTERISTICS (3V OPERATION)
(Typical Application Circuit, 50I system impedance, tuned for 315MHz to 434MHz operation. VDD5 = VGPOVDD = VAVDD =
VDVDD = VPAVDD = 2.1V to 3.6V, fRF = 280MHz to 450MHz, fXTAL = 15MHz to 16MHz, TA = -40NC to +125NC, unless otherwise noted. Typical values are at VDD5 = VGPOVDD = VAVDD = VDVDD = VPAVDD = 2.7V, TA = +25NC, PA matched for
optimum output power, unless otherwise noted. All min and max values are 100% tested at TA = +125NC and guaranteed by design
and characterization over temperature, unless otherwise noted.)
PARAMETER
Supply Voltage
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
2.1
2.7
3.6
V
fRF = 315MHz
4.2
6.2
fRF = 433.92MHz
4.8
7.2
VDD
PLL on, PA off
Active Supply Current
IDD
PLL on, PA on, data
fRF = 315MHz
at 50% duty cycle
(ASK), +10dBm
(PApwr = 0x19)
output power
fRF = 433.92MHz
(Notes 1, 2)
PLL on, PA on, data
at 100% duty cycle, fRF = 315MHz
+10dBm (PApwr =
0x19) output power f = 433.92MHz
RF
(Note 1)
Standby Current
Shutdown Current
ISTDBY
ISHDN
VENABLE < VIL,
VLSHDN < VIL
VENABLE < VIL,
VLSHDN > VIH
11
mA
13
17.2
27
22
31.6
TA = +25NC
0.4
TA = +85NC
0.5
TA = +125NC
2.5
TA = +25NC
0.005
TA = +85NC
0.3
TA = +125NC
2.6
FA
6.0
FA
6.0
_______________________________________________________________________________________ 3
MAX7060
DC ELECTRICAL CHARACTERISTICS (5V OPERATION) (continued)
MAX7060
280MHz to 450MHz Programmable
ASK/FSK Transmitter
DC ELECTRICAL CHARACTERISTICS (3V OPERATION) (continued)
(Typical Application Circuit, 50I system impedance, tuned for 315MHz to 434MHz operation. VDD5 = VGPOVDD = VAVDD =
VDVDD = VPAVDD = 2.1V to 3.6V, fRF = 280MHz to 450MHz, fXTAL = 15MHz to 16MHz, TA = -40NC to +125NC, unless otherwise noted. Typical values are at VDD5 = VGPOVDD = VAVDD = VDVDD = VPAVDD = 2.7V, TA = +25NC, PA matched for
optimum output power, unless otherwise noted. All min and max values are 100% tested at TA = +125NC and guaranteed by design
and characterization over temperature, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
DIGITAL I/O
0.9 x
VDVDD
Input High Threshold
VIH
Input Low Threshold
VIL
Input Pulldown Sink Current
IIH
5
FA
Input Pullup Source Current
IIL
1.3
FA
Output-Voltage High
Output-Voltage Low
VOH
VOL
V
0.1 x
VDVDD
ISINK = 100FA (GPO1 and GPO2_MOD,
gp1bst bit = 0)
VGPOVDD
- 0.10
ISINK = 200FA (GPO1), boost = on
(gp1bst bit = 1)
VGPOVDD
- 0.14
ISOURCE = 100FA (GPO1 and
GPO2_MOD, gp1bst bit = 0)
0.10
ISOURCE = 200FA (GPO1), boost = on
(gp1bst bit = 1)
0.14
V
V
V
AC ELECTRICAL CHARACTERISTICS (5V OPERATION)
(Typical Application Circuit, 50I system impedance, tuned for 315MHz to 434MHz operation, VDD5 = VGPOVDD = 4.5V to 5.5V, fRF =
280MHz to 450MHz, fXTAL = 15MHz to 16MHz, TA = -40NC to +125NC, unless otherwise noted. Typical values are at VDD5 = VGPOVDD
= +5V, TA = +25NC, PA matched for optimum output power, unless otherwise noted. All min and max values are 100% tested at TA
= +125NC and guaranteed by design and characterization over temperature, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
450
MHz
GENERAL CHARACTERISTICS
Frequency Range
Power-On Time
Maximum Data Rate
(PApwr = 0x1E)
280
tON
ENABLE low-to-high transition, frequency
settled to within 50kHz of the desired
carrier (includes time for VPAVOUT to settle)
130
ENABLE low-to-high transition, frequency
settled to within 5kHz of the desired carrier
(includes time for VPAVOUT to settle)
185
ASK mode
(no shaping)
FSK mode
Fs
Manchester encoded
50
Nonreturn to zero
100
Manchester encoded
70
Nonreturn to zero
140
4 _______________________________________________________________________________________
kbps
280MHz to 450MHz Programmable
ASK/FSK Transmitter
(Typical Application Circuit, 50I system impedance, tuned for 315MHz to 434MHz operation, VDD5 = VGPOVDD = 4.5V to 5.5V, fRF =
280MHz to 450MHz, fXTAL = 15MHz to 16MHz, TA = -40NC to +125NC, unless otherwise noted. Typical values are at VDD5 = VGPOVDD
= +5V, TA = +25NC, PA matched for optimum output power, unless otherwise noted. All min and max values are 100% tested at TA
= +125NC and guaranteed by design and characterization over temperature, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
Time from end of SPI write or change of
FREQ0, FREQ1, or FREQ2 pins, to
frequency settled to within 5kHz of desired
carrier
Carrier-Frequency Switching
Time
TYP
MAX
UNITS
60
Fs
340
MHz/V
PLL
VCO Gain
KVCO
fRF = 315MHz
PLL Phase Noise
fRF = 433.92MHz
10kHz offset
-78
1MHz offset
-97
10kHz offset
-74
1MHz offset
dBc/Hz
-97
Loop Bandwidth
300
Reference Frequency Input Level
kHz
500
mVP-P
Frequency Divider Range
19
28
Frequency Deviation (FSK)
Q2
Q100
kHz
CRYSTAL OSCILLATOR
Crystal Frequency
fXTAL
Crystal Load Capacitance
(Note 3)
15 to 16
MHz
10
pF
POWER AMPLIFIER
Output Transmit Power (Note 1)
Power-Control Step Size
POUT
Maximum output transmit power:
PApwr = 0x1E
+14.5
Minimum output transmit power:
PApwr = 0x00
-14
dBm
0.95
dB
Modulation Depth (Note 1)
70
dB
Maximum Carrier Harmonics
(Note 1)
-24
dBc
-42
dBc
0 to 7.75
pF
Reference Spur
PAOUT Capacitor Tuning Range
_______________________________________________________________________________________ 5
MAX7060
AC ELECTRICAL CHARACTERISTICS (5V OPERATION) (continued)
MAX7060
280MHz to 450MHz Programmable
ASK/FSK Transmitter
AC ELECTRICAL CHARACTERISTICS (3V OPERATION)
(Typical Application Circuit, 50I system impedance, tuned for 315MHz to 434MHz operation. VDD5 = VGPOVDD = VAVDD =
VDVDD = VPAVDD = 2.1V to 3.6V, fRF = 280MHz to 450MHz, fXTAL = 15MHz to 16MHz, TA = -40NC to +125NC, unless otherwise noted. Typical values are at VDD5 = VGPOVDD = VAVDD = VDVDD = VPAVDD = 2.7V, TA = +25NC, PA matched for
optimum output power, unless otherwise noted. All min and max values are 100% tested at TA = +125NC and guaranteed by design
and characterization over temperature, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
450
MHz
GENERAL CHARACTERISTICS
Frequency Range
Power-On Time
280
tON
ENABLE low-to-high transition, frequency
settled to within 50kHz of the desired carrier (includes time for VPAVOUT to settle)
120
ENABLE low-to-high transition, frequency
settled to within 5kHz of the desired carrier
(includes time for VPAVOUT to settle)
200
ASK mode
(no shaping)
Maximum Data Rate
(PApwr = 0x19)
FSK mode
Fs
Manchester encoded
50
Nonreturn to zero
100
Manchester encoded
70
Nonreturn to zero
140
Time from end of SPI write or change of
FREQ0, FREQ1, or FREQ2 pins, to
frequency settled to within 5kHz of desired
carrier
Carrier-Frequency Switching
Time
kbps
60
Fs
340
MHz/V
PLL
VCO Gain
KVCO
fRF = 315MHz
PLL Phase Noise
fRF = 433.92MHz
10kHz offset
-78
1MHz offset
-97
10kHz offset
-74
1MHz offset
-97
dBc/Hz
Loop Bandwidth
300
kHz
Reference Frequency Input Level
500
mVP-P
Frequency Divider Range
19
28
CRYSTAL OSCILLATOR
Frequency Deviation (FSK)
Q2
Q100
kHz
15
to 16
MHz
Frequency Pulling by Power
Supply
4
ppm/V
Crystal Load Capacitance
(Note 3)
10
pF
Crystal Frequency
fXTAL
POWER AMPLIFIER
VPAVDD = 2.1V, PApwr = 0x1E
Output Transmit Power (Note 1)
Power-Control Step Size
Modulation Depth (Note 1)
POUT
+10
VPAVDD = 3.6V, PApwr = 0x1E
+15
PApwr = 0x00
-14.5
dBm
0.95
dB
70
dB
6 _______________________________________________________________________________________
280MHz to 450MHz Programmable
ASK/FSK Transmitter
(Typical Application Circuit, 50I system impedance, tuned for 315MHz to 434MHz operation. VDD5 = VGPOVDD = VAVDD =
VDVDD = VPAVDD = 2.1V to 3.6V, fRF = 280MHz to 450MHz, fXTAL = 15MHz to 16MHz, TA = -40NC to +125NC, unless otherwise noted. Typical values are at VDD5 = VGPOVDD = VAVDD = VDVDD = VPAVDD = 2.7V, TA = +25NC, PA matched for
optimum output power, unless otherwise noted. All min and max values are 100% tested at TA = +125NC and guaranteed by design
and characterization over temperature, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
Maximum Carrier Harmonics
(Note 1)
UNITS
-24
dBc
-43
dBc
0 to 7.75
pF
Reference Spur
PAOUT Capacitor Tuning Range
MAX
SERIAL PERIPHERAL INTERFACE (SPI) TIMING CHARACTERISTICS
(SPI timing characteristics are valid for both 3V and 5V modes. SPI timing is production tested at worst-case temperature and supply
with a clock frequency of 3MHz.)
PARAMETER
SYMBOL
Minimum SCLK_PWR0 Low to
Falling-Edge of CS_DEV Setup Time
CONDITIONS
MIN
TYP
MAX
UNITS
tSC
30
ns
Minimum CS_DEV Low to Rising
Edge of SCLK_PWR0 Setup Time
tCSS
15
ns
Minimum SCLK_PWR0 Low to
Rising Edge of CS_DEV Setup
Time
tHCS
60
ns
Minimum SCLK_PWR0 Low After
Rising Edge of CS_DEV Hold Time
tHS
15
ns
Minimum Data Valid to SCLK_
PWR0 Rising-Edge Setup Time
tDS
30
ns
Minimum Data Valid to SCLK_
PWR0 Rising-Edge Hold Time
tDH
15
ns
Minimum SCLK_PWR0 High Pulse
Width
tCH
120
ns
Minimum SCLK_PWR0 Low Pulse
Width
tCL
120
ns
Minimum CS_DEV High Pulse
Width
tCSH
120
ns
Maximum Transition Time from
Falling-Edge of CS_DEV to Valid
GPO2_MOD
tCSG
CL = 10pF load capacitance from
GPO2_MOD to ground
400
ns
Maximum Transition Time from
Falling Edge of SCLK_PWR0 to
Valid GPO2_MOD
tCG
CL = 10pF load capacitance from
GPO2_MOD to ground
400
ns
Note 1: Supply current and output power are greatly dependent on board layout and PAOUT match.
Note 2: 50% duty cycle at 10kHz ASK data (Manchester coded).
Note 3: Dependent on PCB trace capacitance.
_______________________________________________________________________________________ 7
MAX7060
AC ELECTRICAL CHARACTERISTICS (3V OPERATION) (continued)
MAX7060
280MHz to 450MHz Programmable
ASK/FSK Transmitter
CS_DEV
tCSH
tSC
tHCS
tCSS
SCLK_PWRO
tDS
tCH
tCL
tDH
tHS
SDI_PWR1
tCG
tCSG
GPO2_MOD
Figure 1. SPI Timing Diagram
Typical Operating Characteristics
(Typical Application Circuit, 50I system impedance, VDD5 = VGPOVDD = VAVDD = VDVDD = VPAVDD = 2.1V to 3.6V, fRF = 280MHz to
450MHz, fXTAL = 16MHz, TA = -40NC to +125NC, unless otherwise noted. Typical values are at VDD5 = VGPOVDD = VAVDD = VDVDD
= VPAVDD = 2.7V, TA = +25NC, PA matched for optimum output power, unless otherwise noted. Supply current and output power are
greatly dependent on board layout and PAOUT match.)
SUPPLY CURRENT vs. SUPPLY VOLTAGE
(fRF = 315MHz, PA ON)
TA = -40°C
24
TA = +125°C
PApwr = 0x1E
TA = +85°C
20
18
+125°C
16
PApwr = 0x16
14
20
TA = +125°C
18
+125°C
PApwr = 0x16
16
2.4
2.7
3.0
3.3
MAX7060 toc03
4
TA = +25°C
TA = -40°C
2
4.5
3.6
TA = +85°C
5
-40°C
10
2.1
TA = +125°C
6
3
12
-40°C
10
4.7
4.9
5.1
5.3
5.5
2.1
2.4
2.7
3.0
3.3
3.6
VDD5 (V)
VDD5 (V)
SUPPLY CURRENT vs. SUPPLY VOLTAGE
(fRF = 433.92MHz, PA ON)
SUPPLY CURRENT vs. SUPPLY VOLTAGE
(fRF = 433.92MHz, PA ON)
SUPPLY CURRENT vs. SUPPLY VOLTAGE
(fRF = 433.92MHz, PA OFF)
3V MODE
TA = +25°C
TA = -40°C
30
28
TA = +125°C
PApwr = 0x1E
36
MAX7060 toc04
38
36
34
32
TA = +85°C
-40°C
PApwr = 0x16
PApwr = 0x1E
34
5V MODE
32
30
TA = +85°C
28
TA = +25°C
TA = -40°C
TA = +125°C
26
24
-40°C
PApwr = 0x16
22
20
+125°C
16
14
2.1
2.4
2.7
3.0
VDD5 (V)
3.3
3.6
3V MODE
7
TA = +125°C
TA = +85°C
6
5
4
TA = +25°C
TA = -40°C
3
18
+125°C
8
4.5
4.7
4.9
5.1
VDD5 (V)
5.3
MAX7060 toc06
VDD5 (V)
SUPPLY CURRENT (mA)
SUPPLY CURRENT (mA)
22
TA = +85°C TA = +25°C
14
12
26
24
22
20
18
16
TA = -40°C
24
SUPPLY CURRENT (mA)
22
26
3V MODE
7
MAX7060 toc05
SUPPLY CURRENT (mA)
26
8
MAX7060 toc02
TA = +25°C
PApwr = 0x1E
5V MODE
28
SUPPLY CURRENT (mA)
3V MODE
28
30
MAX7060 toc01
30
SUPPLY CURRENT vs. SUPPLY VOLTAGE
(fRF = 315MHz, PA OFF)
SUPPLY CURRENT (mA)
SUPPLY CURRENT vs. SUPPLY VOLTAGE
(fRF = 315MHz, PA ON)
2
5.5
2.1
2.4
2.7
3.0
VDD5 (V)
8 _______________________________________________________________________________________
3.3
3.6
280MHz to 450MHz Programmable
ASK/FSK Transmitter
OUTPUT POWER vs. SUPPLY VOLTAGE
(fRF = 315MHz, PA ON)
PApwr = 0x1E
TA = +125°C
TA = +25°C
TA = +85°C
TA = -40°C
PApwr = 0x16
8
16
3V MODE
14
TA = +125°C TA = +25°C
11
TA = +85°C
PApwr = 0x16
TA = +25°C
TA = +125°C
TA = +125°C
2.1
2.4
2.7
3.0
3.3
10
TA = +125°C
TA = -40°C TA = +25°C
8
6
4
TA = -40°C
5
3.6
TA = +25°C TA = +85°C
TA = -40°C
PApwr = 0x1E
12
7
4
4.5
4.7
PApwr = 0x16
2
4.9
5.1
5.3
5.5
2.1
2.4
TA = +85°C
2.7
TA = +125°C
3.0
3.3
3.6
VDD5 (V)
VDD5 (V)
VDD5 (V)
OUTPUT POWER vs. SUPPLY VOLTAGE
(fRF = 433.92MHz, PA ON)
PA POWER
vs. PA POWER CODE, 315MHz
SUPPLY CURRENT
vs. PA POWER CODE, 315MHz
20
13
VDD5 = 3.6V
3V MODE
15
10
TA = +125°C TA = +25°C
9
POUT (dBm)
11
TA = -40°C
TA = -40°C TA = +85°C
PApwr = 0x16
VDD5 = 2.7V
VDD5 = 2.1V
0
-5
5
3
4.5
4.9
5.1
5.3
0
5
10
15
20
25
30
0
35
5
10
15
20
25
30
PA POWER CODE (DECIMAL)
PA POWER
vs. PA POWER CODE, 315MHz
SUPPLY CURRENT
vs. PA POWER CODE, 315MHz
PA POWER
vs. PA POWER CODE, 433.92MHz
25
-4
VDD5 = 5V
VDD5 = 4.5V
20
15
VDD5 = 5.5V
35
0
5
10
VDD5 = 3.6V
VDD5 = 2.7V
5
VDD5 = 2.1V
0
-5
-15
VDD5 = 5V
5
10
15
20
25
30
PA POWER CODE (DECIMAL)
35
-10
-12
5
3V MODE
15
10
10
-16
20
MAX7060 toc14
5V MODE
POUT (dBm)
VDD5 = 4.5V
VDD5 = 5.5V
-8
30
SUPPLY CURRENT (mA)
4
0
VDD5 = 2.1V
10
PA POWER CODE (DECIMAL)
8
0
VDD5 = 2.7V
15
VDD5 (V)
5V MODE
12
20
0
-15
5.5
MAX7060 toc13
16
4.7
VDD5 = 3.6V
25
5
-10
TA = +25°C TA = +125°C
3V MODE
30
MAX7060 toc15
7
5
35
MAX7060 toc12
5V MODE
SUPPLY CURRENT (mA)
TA = +85°C
MAX7060 toc11
PApwr = 0x1E
MAX7060 toc10
15
POUT (dBm)
5V MODE
TA = -40°C
9
6
POUT (dBm)
TA = +85°C
13
12
10
PApwr = 0x1E
15
POUT (dBm)
POUT (dBm)
14
17
MAX7060 toc09
16
TA = +25°C T = +85°C
A
TA = -40°C
POUT (dBm)
3V MODE
MAX7060 toc07
18
OUTPUT POWER vs. SUPPLY VOLTAGE
(fRF = 433.92MHz, PA ON)
MAX7060 toc08
OUTPUT POWER vs. SUPPLY VOLTAGE
(fRF = 315MHz, PA ON)
15
20
25
PA POWER CODE (DECIMAL)
30
35
-20
0
5
10
15
20
25
30
PA POWER CODE (DECIMAL)
35
_______________________________________________________________________________________ 9
MAX7060
Typical Operating Characteristics (continued)
(Typical Application Circuit, 50I system impedance, VDD5 = VGPOVDD = VAVDD = VDVDD = VPAVDD = 2.1V to 3.6V, fRF = 280MHz to
450MHz, fXTAL = 16MHz, TA = -40NC to +125NC, unless otherwise noted. Typical values are at VDD5 = VGPOVDD = VAVDD = VDVDD
= VPAVDD = 2.7V, TA = +25NC, PA matched for optimum output power, unless otherwise noted. Supply current and output power are
greatly dependent on board layout and PAOUT match.)
Typical Operating Characteristics (continued)
(Typical Application Circuit, 50I system impedance, VDD5 = VGPOVDD = VAVDD = VDVDD = VPAVDD = 2.1V to 3.6V, fRF = 280MHz to
450MHz, fXTAL = 16MHz, TA = -40NC to +125NC, unless otherwise noted. Typical values are at VDD5 = VGPOVDD = VAVDD = VDVDD
= VPAVDD = 2.7V, TA = +25NC, PA matched for optimum output power, unless otherwise noted. Supply current and output power are
greatly dependent on board layout and PAOUT match.)
VDD5 = 4.5V
5V MODE
10
5
VDD5 = 2.7V
25
20
15
0
VDD5 = 5.5V
-5
VDD5 = 5V
VDD5 = 2.1V
10
35
5V MODE
0
0
5
10
15
20
25
30
20
VDD5 = 5.5V
15
VDD5 = 5V
5
-15
35
25
10
-10
5
VDD5 = 4.5V
30
SUPPLY CURRENT (mA)
35
30
15
POUT (dBm)
0
5
10
15
20
25
30
0
35
5
10
15
20
25
30
PA POWER CODE (DECIMAL)
PA POWER CODE (DECIMAL)
PA POWER CODE (DECIMAL)
PHASE NOISE vs. OFFSET FREQUENCY
(fRF = 315MHz, TA = +25°C,
VDD = 2.7V, PA CODE = 0x19)
PHASE NOISE vs. OFFSET FREQUENCY
(fRF = 433.92MHz, TA = +25°C,
VDD = 2.7V, PA CODE = 0x19)
REFERENCE SPUR MAGNITUDE
vs. SUPPLY VOLTAGE
PHASE NOISE (dBc/Hz)
-80
-60
-90
-100
-110
-70
-80
-90
-100
-120
-110
-130
-120
1k
10k
100k
1M
OFFSET FREQUENCY (Hz)
10M
433.92MHz
315MHz
-44
-46
-48
-130
-140
3V MODE
-42
35
MAX7060 toc21
-70
-40
REFERENCE SPUR MAGNITUDE (dBc)
-50
MAX7060 toc19
-60
MAX7060 toc20
SUPPLY CURRENT (mA)
VDD5 = 3.6V
MAX7060 toc17
3V MODE
MAX7060 toc16
45
40
SUPPLY CURRENT
vs. PA POWER CODE, 433.92MHZ
PA POWER
vs. PA POWER CODE, 433.92MHz
MAX7060 toc18
SUPPLY CURRENT
vs. PA POWER CODE, 433.92MHZ
PHASE NOISE (dBc/Hz)
MAX7060
280MHz to 450MHz Programmable
ASK/FSK Transmitter
1k
10k
100k
1M
OFFSET FREQUENCY (Hz)
10M
2.1
2.4
2.7
3.0
SUPPLY VOLTAGE (V)
10 �������������������������������������������������������������������������������������
3.3
3.6
280MHz to 450MHz Programmable
ASK/FSK Transmitter
FSK SPECTRUM (fRF = 315MHz, +25°C, VDD = 2.7V,
PA CODE = 0x19 ±50kHz DEVIATION,
4kHz SQUARE WAVE ON DIN)
REFERENCE SPUR MAGNITUDE
vs. SUPPLY VOLTAGE
POUT (dBm)
-44
RBW = 10kHz
VBW = 10kHz
10
433.92MHz
315MHz
-46
MAX7060 toc23
MAX7060 toc22
5V MODE
-42
20
0
-10
-20
-48
4.5
4.7
4.9
5.1
5.3
-30
314.5
5.5
314.7
314.9
SUPPLY VOLTAGE (V)
315.1
315.3
315.5
fRF (MHz)
XTAL1
XTAL2
AVDD
N.C.
VDD5
PAVOUT
Pin Configuration/Functional Diagram
18
17
16
15
14
13
CRYSTAL OSCILLATOR
20
SCLK_PWR0
21
ENABLE
22
DIN
23
LOOP
FILTER
PFD
VCO
PA
ASK DATA
Σ∆
MODULATOR
3
1
2
3
GPO1
DVDD
12
ROUT
11
PAVDD
10
PAOUT
9
N.C.
8
LSHDN
7
FREQ2
5
EXPOSED PAD
GND
MAX7060
24
+
PULSE
SHAPING
PA POWER CONTROL
FREQUENCY
DIVIDER
SERIAL
INTERFACE,
CONFIGURATION,
AND CONTROL
/K
N.C.
VOLTAGE
REGULATOR
4
5
6
FREQ1
SDI_PWR1
CHARGE
PUMP
FREQ0
19
GPOVDD
CS_DEV
GPO2_MOD
REFERENCE SPUR MAGNITUDE (dBc)
-40
TQFN
______________________________________________________________________________________ 11
MAX7060
Typical Operating Characteristics (continued)
(Typical Application Circuit, 50I system impedance, VDD5 = VGPOVDD = VAVDD = VDVDD = VPAVDD = 2.1V to 3.6V, fRF = 280MHz to
450MHz, fXTAL = 16MHz, TA = -40NC to +125NC, unless otherwise noted. Typical values are at VDD5 = VGPOVDD = VAVDD = VDVDD
= VPAVDD = 2.7V, TA = +25NC, PA matched for optimum output power, unless otherwise noted. Supply current and output power are
greatly dependent on board layout and PAOUT match.)
MAX7060
280MHz to 450MHz Programmable
ASK/FSK Transmitter
Pin Description
PIN
NAME
FUNCTION
1
GPO2_MOD
(SPI Mode/Manual Mode) Digital Input/Output. GPO2 output in SPI mode. Acts as an SPI data
output when CS_DEV is low. ASK (0)/FSK (1) modulation select input in manual mode. This pin is
internally pulled down in manual mode.
2
GPO1
General-Purpose Output 1. In SPI mode, this pin can output many internal status signals. In
manual mode, this pin outputs the synthesizer lock-detect (lockdet) signal.
3
DVDD
Digital-Supply Voltage Input. Bypass to GND with a 0.01FF capacitor as close as possible to the pin.
4
GPOVDD
5
FREQ0
Frequency-Select Pin 0 in Manual Mode. Internally pulled down. FREQ0 = FREQ1 = FREQ2 = 0
for SPI mode.
6
FREQ1
Frequency-Select Pin 1 in Manual Mode. Internally pulled down. FREQ0 = FREQ1 = FREQ2 = 0
for SPI mode.
7
FREQ2
Frequency-Select Pin 2 in Manual Mode. Internally pulled down. FREQ0 = FREQ1 = FREQ2 = 0
for SPI mode.
8
LSHDN
Low-Power Shutdown Current-Select Digital Input. Turns off internal POR circuit and disables
pullup/pulldown currents. Must be driven low for normal operation in 3V mode. Functional only in
3V mode. Connect to GND in 5V mode.
9, 15, 24
N.C.
10
PAOUT
Power Amplifier Output. Requires a pullup inductor to PAVOUT, which can be part of the outputmatching network to an antenna.
11
PAVDD
Power Amplifier Predriver Power-Supply Input. Bypass to GND with a 680pF capacitor and a
0.01FF as close as possible to the pin.
12
ROUT
13
PAVOUT
14
VDD5
16
AVDD
17
XTAL2
Supply Voltage Input. Bypass to ground with 0.01FF and 0.1FF capacitors.
Analog Supply Voltage and Regulator Output. Bypass to GND with 0.1FF and 0.01FF capacitors
as close as possible to the pin.
Crystal Input 2. XTAL2 can be driven from an AC-coupled external reference.
18
XTAL1
Crystal Input 1. AC-couple to GND if XTAL2 is driven from an AC-coupled external reference.
19
CS_DEV
(SPI Mode/Manual Mode) Serial Peripheral Interface (SPI) Active-Low Chip-Select Input. FSK
frequency-deviation input (0 = low deviation, 1 = high deviation) in manual mode. Internally
pulled up.
20
SDI_PWR1
21
SCLK_PWR0
22
ENABLE
23
DIN
Transmit Data Digital Input. Internally pulled down.
—
EP
Exposed Pad. Solder evenly to the board’s ground plane for proper operation.
Power-Supply Voltage Input for GPOs and ESD-Protection Devices. Bypass to GND with a
0.01FF capacitor as close as possible to the pin.
No Connection. Internally not connected. Leave unconnected.
Envelope-Shaping Resistor Connection. See the Typical Application Circuits and the ASK
Envelope Shaping sections for details.
Power Amplifier Power-Control Output. Controls the transmitted power. Connect to PA pullup
inductor. Bypass to ground with 680pF capacitor.
(SPI Mode/Manual Mode) SPI Data Input in SPI Mode. Power-control MSB input in manual mode.
Internally pulled down.
(SPI Mode/Manual Mode) SPI Clock Input in SPI Mode. Power-control LSB input in manual
mode. Internally pulled down.
Enable Digital Input. All internal circuits (except the PA in ASK mode) are enabled on the rising
edge of ENABLE. Internally pulled down.
12 �������������������������������������������������������������������������������������
280MHz to 450MHz Programmable
ASK/FSK Transmitter
The MAX7060 is power and frequency programmable
from 280MHz to 450MHz. The MAX7060 has an internal
transmit power control that can be programmed over a
28dB power range. The MAX7060 has tuning capacitors
at the output of the power amplifier (PA) to ensure highpower efficiency at various programmable frequencies
with a single matching network.
The crystal-based architecture of the MAX7060 eliminates many of the common problems with SAW transmitters by providing greater modulation depth, faster
frequency settling, tighter tolerance of the transmit frequency, and reduced temperature dependence. In particular, the tighter transmit frequency tolerance means
that a superheterodyne receiver with a narrower IF
bandwidth (therefore lower noise bandwidth) can be
used. The payoff is better overall receiver performance
when using a superheterodyne receiver such as the
MAX1473, MAX1471, MAX7033, MAX7034, MAX7036,
and MAX7042.
The MAX7060 can be configured in either SPI or manual
mode, where the transmitter can easily be configured
without the need of an SPI interface.
In the 3V operation, the MAX7060 can be put in a lowpower shutdown mode by pulling ENABLE low and
LSHDN high. In this mode, all the blocks are shut down
including power-on reset (POR). All the MAX7060 registers must be reprogrammed after LSHDN is asserted
high. In the 5V operation, the low-power shutdown mode
is not available, and LSHDN should be connected to
GND.
Frequency Programming
The MAX7060 is a crystal-referenced phased-lockedloop (PLL) VHF/UHF transmitter that transmits data over
a wide frequency range. The internal VCO can be tuned
from 280MHz to 450MHz and controlled by a single
crystal to cover up to a 1.47:1 carrier-frequency range.
The transmit frequency is set by the crystal frequency
and the programmable divider in the PLL; the programmable PLL divide ratios can be set anywhere from 19 to
28, which means that with a crystal frequency of 15MHz,
the output is 285MHz to 420MHz. With a crystal frequency of 16MHz, the output is 304MHz to 448MHz.
The MAX7060 has an internal variable capacitor connected across the PA output. This capacitor can be programmed to maintain high-efficiency transmission at any
frequency within a 1.47 to 1 (28/19) tuning range. This
means that it is possible to change the frequency and
retune the antenna to the new frequency in a very short
time. The combination of rapid antenna-tuning ability
with rapid synthesizer tuning makes the MAX7060 a true
frequency-agile transmitter. The tuning capacitor has a
nominal resolution of 0.25pF, from 0 to 7.75pF.
The MAX7060 supports data rates up to 100kbps NRZ
in ASK mode and 140kbps NRZ in FSK mode. In FSK
mode, the frequency deviation corresponding to bit 1
and bit 0 can be set as low as Q2kHz, and as high as
Q100kHz. The frequency deviation is fully programmable
in SPI mode, and can be selected either as Q16kHz or
Q50kHz in manual mode.
Power Amplifier (PA)
The PA of the MAX7060 is a high-efficiency, open-drain
switching-mode amplifier. In a switching-mode amplifier,
the gate of the final-stage FET is driven with a very sharp
25% duty-cycle square wave at the transmit frequency.
This square wave is derived from the synthesizer circuit.
When the matching network is tuned correctly, the output
FET resonates the attached tank circuit with a minimum
amount of power dissipated in the FET. With a proper
output-matching network, the PA can drive a wide range
of antenna impedances, which include a small-loop PCB
trace and a 50I antenna. The output-matching network
suppresses the carrier harmonics and transforms the
antenna impedance to an optimal impedance at PAOUT,
which is from 60I to 125I. When the output-matching
network is properly tuned, the MAX7060 transmits power
with a high overall efficiency. The efficiency of the PA
itself is approximately 50%.
Transmitter Power Control
The transmitter power of the MAX7060 can be set in
approximately 1dB steps (SPI mode) to produce a maximum output power level of +14dBm with a 5V supply.
If a battery is used as the supply, the maximum output
power level varies from +15dBm at 3.6V to +10dBm at
2.1V. The minimum power level is -14dBm for both 5V
and battery supplies. The maximum transmitter power
(and the transmitter current) can be lowered by increasing the load impedance on the PA. Four fixed power
levels are available in manual mode.
When a 5V supply is used, the VDD5 and GPOVDD pins
are connected to the 5V supply. AVDD is the output of
an internal voltage regulator and must be connected
externally to DVDD and PAVDD. The PAVOUT pin is
connected to the PAOUT pin through a biasing inductor.
PAVOUT is not connected to any of the power-supply
______________________________________________________________________________________ 13
MAX7060
Detailed Description
MAX7060
280MHz to 450MHz Programmable
ASK/FSK Transmitter
pins. Connecting PAVOUT to PAOUT enables Tx power
control. In SPI mode, there are 31 power-control settings
in approximately 1dB monotonic steps. In manual mode,
four power-control settings are available.
ASK Envelope Shaping
The MAX7060 has two types of ASK envelope shaping:
digital shaping (SPI mode only) and analog shaping
through an internal resistor. Envelope shaping results
in a smaller spectral width of the modulated PA output
signal.
In digital shaping, the user can choose the final Tx power
setting, the power step size in units as small as 1dB, and
the step-time interval in units as small as 0.25Fs, when a
16MHz crystal is used. This shaping method causes the
PA to transmit an envelope that rises linearly in decibels
(exponentially in power) with time. Digital shaping is programmed through the SPI.
The analog shaping mode uses an internal envelopeshaping resistor for ASK modulation, which connects
between PAVOUT and ROUT. When the ROUT pin
(rather than the PAVOUT pin) is connected to the PA
pullup inductor, the envelope-shaping resistor slows the
turn-on/turn-off time of the PA. The user can choose two
turn-on/turn-off times through the SPI. A single turn-on/
turn-off time is set internally in manual mode.
It should be noted that, by default, data pulses applied
to the DIN pin are internally lengthened by 64 crystal
clock cycles (4μs for a 16MHz crystal) to allow time
for the analog shaping to occur. For cases in which
no analog shaping is desired, the PA pullup inductor
must be connected to PAVOUT and the analog shaping
bits in the Conf0 register set to either anshp[1:0] = 00,
which leaves the extra 4μs pulse extension in place, or
to anshp[1:0] = 11, which removes the extra 4μs and
allows transmitted pulses to track the data present at the
DIN pin. If digital shaping is used, the PA pullup inductor
must be connected to PAVOUT and there is no 4μs pulse
extension, regardless of the status of the anshp[1:0] bits.
At low data rates, where shaping is not necessary and
the 4μs pulse lengthening has minimal impact on duty
cycle symmetry, it may be acceptable to use the default
configuration of anshp[1:0] = 00. For higher data rates, it
may be necessary to use anshp[1:0] = 11, to avoid duty
cycle skew. Another method to remove the pulse lengthening is to apply a minimal amount of digital shaping,
by setting tstep[3:0] = 0001 and selecting pastep[4:0]
= papwr[4:0].
Variable Capacitor
The MAX7060 has an internal set of capacitors that can
be switched in and out to present different capacitor
values at the PA output. The capacitors are connected
from the PA output to ground. This allows changing the
tuning network along with the synthesizer divide ratio
each time the transmitted frequency changes, making
it possible to maintain maximum transmitter power while
moving rapidly from one frequency to another.
In SPI mode, the variable capacitor is programmed
through a register setting. In manual mode, the capacitor
setting is programmed through the DIN pin.
The tuning capacitor has a nominal resolution of 0.25pF,
from 0 to 7.75pF.
Phase-Locked Loop (PLL)
The MAX7060 utilizes a fully integrated fractional-N
PLL for its frequency synthesizer. All PLL components,
including the loop filter, are included on-chip. Two loop
bandwidths can be selected in SPI mode. The synthesizer has 16-bit fractional-N topology (4 bits integer, 12
bits fractional) with a divide ratio that can be set from 19
to 28, allowing the transmit frequency to be adjusted in
increments of fXTAL/4096.
The fractional-N architecture also allows exact FSK
frequency deviations to be programmed, completely
eliminating the problems associated with generating frequency deviations by crystal oscillator pulling.
FSK deviations as low as Q2kHz and as high as Q100kHz
can be set in SPI mode. In manual mode, the user can
select between Q16kHz and Q50kHz.
The integer and fractional portions of the PLL divider
ratio set the transmit frequency. This is done by loading the divide-ratio registers in SPI mode, or selecting
the states of the three frequency-control pins (FREQ2,
FREQ1, FREQ0) in manual mode. For ASK modulation,
the two 8-bit center-frequency registers (fce[15:0]) are
loaded with the divide ratio determined by the center
frequency and the crystal. For FSK modulation, the two
8-bit high (mark) frequency registers (fhi[15:0]) and the
two 8-bit low (space) frequency registers (flo[15:0]) are
loaded. The divide ratios for the fhi and flo are determined by the center frequency, the frequency deviation,
and the crystal frequency. Examples of typical settings
for ASK and FSK modulation are given in the SPI Mode
Settings section.
14 �������������������������������������������������������������������������������������
280MHz to 450MHz Programmable
ASK/FSK Transmitter
In actuality, the oscillator pulls every crystal. The crystal’s
natural frequency is really below its specified frequency,
but when loaded with the specified load capacitance,
the crystal is pulled and oscillates at its specified frequency. This pulling is already accounted for in the
specification of the load capacitance.
Additional pulling can be calculated if the electrical
parameters of the crystal are known. The frequency pulling is given by:
fP
=

CM 
1
1
6
−

 × 10
2  C CASE + C LOAD C CASE + C SPEC 
General-Purpose Output
(GPO)/Clock Outputs
The MAX7060 has two GPO pins in SPI mode (GPO2_
MOD and GPO1) and one GPO in manual mode (GPO1).
The GPO1 pin can serve as a clock for a microprocessor
or any other GPO function in SPI mode. In manual mode,
this pin outputs the synthesizer lock-detect (lockdet)
status, after which the user can send data through the
DIN pin.
The GPO2_MOD pin acts as the SPI data output when
the CS_DEV pin is low, in SPI mode. When CS_DEV is
high, it acts as a GPO that can output various internal
signals, such as the synthesizer lock detect (lockdet).
In SPI mode, the output clock that can be routed through
GPO1 is a divided version of the crystal frequency. The
divide ratio is set through the MAX7060 registers, and
the divide settings are 1 (no division), 2, 4, 8, or 16.
When driving an output clock through GPO1, the gp1bst
bit (register Conf0, address 0x01, bit 6) can be set to
1 to increase GPO1 drive strength. If even more drive
capability is required, the user should provide an external buffer.
Serial Peripheral Interface (SPI)
The MAX7060 utilizes a 4-wire SPI protocol for programming its registers, configuring and controlling the
operation of the whole transmitter. For SPI operation, the
FREQ2, FREQ1, and FREQ0 pins must be reset to 0.
The following digital I/Os control the operation of the SPI:
where:
CS_DEV
Active-low SPI chip select
fP is the amount the crystal frequency pulled in ppm
SDI_PWR1
SPI data Input
CM is the motional capacitance of the crystal
SCLK_PWR0
SPI clock
CCASE is the case capacitance
GPO2_MOD
SPI data output
CSPEC is the specified load capacitance
Figure 2 shows the general timing diagram of the SPI
protocol.
CLOAD is the actual load capacitance
When the crystal is loaded as specified (i.e., CLOAD =
CSPEC), the frequency pulling equals zero.
Any number of 8-bit data bursts (Data 1, Data 2 … Data
n) can be sent within one cycle of the CS_DEV pin, to
allow for burst-write or burst-read operations. The SPI
data output signal is routed through the GPO2_MOD pin
when CS_DEV is low.
______________________________________________________________________________________ 15
MAX7060
Crystal (XTAL) Oscillator
The XTAL oscillator in the MAX7060 is designed to present a capacitance of approximately 6pF between the
XTAL1 and XTAL2 pins. In most cases, this corresponds
to a 8pF load capacitance applied to the external crystal
when typical PCB parasitics are added. It is very important to use a crystal with a load capacitance equal to the
capacitance of the MAX7060 crystal oscillator plus PCB
parasitics. If a crystal designed to oscillate with a different load capacitance is used, the crystal is pulled away
from its stated operating frequency, introducing an error
in the reference frequency. A crystal designed to operate at a higher load capacitance than the value specified
for the oscillator is always pulled higher in frequency.
Adding capacitance to increase the load capacitance
on the crystal increases the startup time and can prevent
oscillation altogether.
MAX7060
280MHz to 450MHz Programmable
ASK/FSK Transmitter
CS_DEV
SCLK_PWR0
SDI_PWR1
DI7
DI6
DI5
DI4
DI3
DI2
DI1
DI0
DI7
DI6
DI5
DI4
DI3
DI2
DI1
DI0
GPO2_MOD
DO7
DO6
DO5
DO4
DO3
DO2
DO1
DO0
DO7
DO6
DO5
DO4
DO3
DO2
DO1
DO0
DATA 1
DATA n
Figure 2. SPI Format
SPI Commands
The following commands are implemented in the MAX7060:
Write: Within the same CS_DEV cycle, a write command is implemented as follows:
SDI_PWR1:
<0x01> <Initial Address> <Data 1> <Data 2> … <Data N>
With this command, Data 1 is written to the address given by <Initial Address>, Data 2 is written to <Initial Address +
1>, and so on.
Read: Within the same CS_DEV cycle, a read command is implemented as follows:
SDI_PWR1:
<0x02> <Address 1>
GPO2_MOD:
<0xXX>
<Address 2>
<0xXX>
<Address 3> … <Address N>
<Data 1>
<0x00>
<
Data 2> … <Data N - 1> <Data N>
With this command, all the registers can be read within the same cycle of CS_DEV. The addresses can be given in
any order.
CS_DEV
SCLK_PWR0
SDI_PWR1
A7
WRITE COMMAND (0x01)
A6
A5
A4
A3
A2
A1
INITIAL ADDRESS (A[7:0])
A0
D7
D6
D5
D4
D3
D2 D1
D0
DATA 1
Figure 3. SPI Write Command Format
16 �������������������������������������������������������������������������������������
D7
DATA N
D0
280MHz to 450MHz Programmable
ASK/FSK Transmitter
MAX7060
CS_DEV
SCLK_PWR0
SDI_PWR1
A7 A6 A5 A4
READ COMMAND (0x02)
A3 A2
A1
A0 A7 A6 A5
ADDRESS 1
A4
A3 A2
A1 A0 A7
ADDRESS 2
A0
ADDRESS N
D7 D6 D5 D4 D3 D2 D1 D0 D7
GPO2_MOD
DATA 1
0x00
D0 D7
DATA 2
D0
DATA N
Figure 4. SPI Read Command Format
Read All: Within two CS_DEV cycles, the read-all command is implemented as follows:
CS_DEV Cycle 1
SDI_PWR1:
GPO2_MOD:
<0x03><Address N>
CS_DEV Cycle 2
<0x00>
<0x00>
<0x00>
...
<0x00>
<Data N><Data N + 1><Data N + 2>...<Data N + n>
Reset: An SPI reset command is implemented as follows:
SDI_PWR1:<0x04>
An internal active-low master reset pulse is generated, from the falling edge of the last SCLK_PWR0 signal to the falling
edge of the following CS_DEV signal (tHCS + tCSH).
CS_DEV
SCLK_PWR0
SDI_PWR1
A7 A6 A5 A4 A3 A2 A1 A0
READ-ALL COMMAND (0x03)
ADDRESS N
GPO2_MOD
D7 D6 D5 D4 D3 D2 D1 D0 D7
DATA N
D0 D7
DATA N + 1
D0
DATA N + n
Figure 5. SPI Read-All Command Format
CS_DEV
SCLK_PWRO
SDI_PWR1
RESET COMMAND (0x04)
INTERNAL
RESET PULSE
Figure 6. SPI Reset Command Format
______________________________________________________________________________________ 17
MAX7060
280MHz to 450MHz Programmable
ASK/FSK Transmitter
Applications Information
SPI Mode Settings
ASK Carrier Frequency
When the MAX7060 is in ASK mode, only the carrier
frequency needs to be set. To do this, the user calculates the divide ratio based on the carrier frequency and
crystal frequency. The example below shows how to
determine the correct value to be loaded into the carrierfrequency registers (fce[15:0]).
Due to the nature of the transmit PLL frequency divider,
a fixed offset of 16 must be subtracted from the transmit PLL divider ratio for programming the MAX7060’s
transmit-frequency registers. To determine the value to
program the MAX7060’s transmit-frequency registers,
convert the decimal value of the following equation to the
nearest hexadecimal value:
 fRF

decimal value to program the
− 16 × 4096 =

transmit-frequency registers
f
 XTAL

Assume the ASK transmit frequency = 315MHz and
fXTAL = 16MHz. In this example, the rounded decimal
value is 15,104 or 0x3B00. The upper byte (0x3B) is
loaded into the FCenter0 register (fce[15:8]) and the
lower byte (0x00) is loaded into the FCenter1 register
(fce[7:0]).
FSK Mark and Space Frequencies
When the MAX7060 is in FSK mode, two frequencies
need to be set: the mark (logical 1) frequency and the
space (logical 0) frequency. In most cases, the two frequencies are above and below the carrier frequency by
the deviation frequency. Therefore, the user needs to
calculate the divide ratio for both frequencies and load
them into four registers. The procedure for calculating
the register settings is the same as it is for calculating
the carrier frequency. The example below shows how to
determine the register settings for the mark and space
frequencies when the frequency deviation is ±50kHz
(100kHz between mark and space).
Assume that, for an FSK transmitter centered at
433.92MHz, the mark frequency is 433.97MHz, the
space frequency is 433.87MHz, and the crystal frequency is 16MHz. In this example, the rounded decimal
value for the mark frequency is 45,560 or 0xB1F8. For the
space frequency, the rounded decimal value is 45,535
or 0xB1DE. The mark setting is loaded into the FHigh0
and FHigh1 registers (fhi[15:0]), and the space setting
is loaded into the FLow0 and FLow1 registers (flo[15:0]).
Transmit Power Settings (5V Supply)
The output power level is set by entering a 5-bit value
into the PApwr register (papwr[4:0]). The highest setting
(30dec or 0x1E) corresponds to the highest transmitted power level. Each step is slightly less than 1dB
(approximately 0.95dB), with the lowest setting producing a transmitted power 28dB lower than the highest.
The highest transmitted power depends on the load
presented to the PA output. A 50I or 60I load produces
an output power level of +14dBm to +15dBm when the
highest papwr[4:0] setting (0x1E) is applied. Increasing
the load resistance reduces the output power level.
Reducing the setting by one step reduces the power by
approximately 1dB, and the minimum transmitted power
is still about 28dB below the maximum. For example, if
the load resistance is increased to the point where the
output power for the maximum setting (0x1E) is +10dBm,
then the minimum setting (0x00) produces an output
power of about -18dBm.
Transmit Power Settings (3V Supply)
The output power level in 3V operation is set the same
way as in 5V operation, but the variation in the 3V supply (the specified range is 2.1V to 3.6V) affects the
maximum power that can be transmitted. If the supply
is 3.6V, then the maximum papwr[4:0] setting (0x1E)
still produces a +14dBm to +15dBm transmitted power
level. As the supply voltage decreases, the transmitted
power at the highest settings is compressed, so that
the top setting and an increasing number of the lower
settings produce the same transmitted power, which
is lower than the +14dBm to +15dBm achieved with a
3.6V supply. For example, a 2.7V supply produces a
maximum transmitter power of +12dBm to +13dBm, and
the PApwr register settings from 0x1B to 0x1E (27dec to
30dec) produce the same transmitter power. Below this
compressed range, the power settings give the same
power levels that they would give with a 5V supply. At
the lowest supply level of 2.1V, the maximum setting
produces a maximum transmitter power of +10dBm, and
the PApwr register settings from 0x19 to 0x1E (25dec to
30dec) produce the same transmitter power. The effect
of a lower supply voltage reduces the maximum power
and the adjustment range. The power at the lowest setting remains unchanged.
The transmitted power using a 3V supply can be set
higher than the levels described in the paragraph above
by connecting PAOUT directly to PAVDD and disconnecting (leave open) the PAVOUT pin. The tradeoff of this
connection is that there is no transmit power adjustment.
18 �������������������������������������������������������������������������������������
280MHz to 450MHz Programmable
ASK/FSK Transmitter
Digital Amplitude Shaping
The digital shaping feature allows the user to choose a
linear stairstep function to increase and decrease the
power when the PA is turned on and off for an ASK bit
interval. There are three registers that control the digital
amplitude shaping settings. The first setting is the final
power of the PA when the pulse reaches its maximum
(PApwr register). The second setting is the amplitude
change, in decibels, for each step, which is the vertical
axis of the stairstep (PAstep register). The third setting
is the time interval of each step, which is the horizontal
axis of the stairstep (Tstep register). The final power setting (decimal 0 to 30 in increments of 1dB) is entered in
the PApwr register. The amplitude step (decimal 0 to 30
in increments of 1dB) is entered in the PAstep register.
The time interval (decimal 0 to 60/fXTAL in increments of
4/fXTAL) is entered in the Tstep register. For example, to
shape an 80kbps NRZ data stream (12.5Fs bit interval),
the user might choose a maximum power level of 0x1E
(30dec), an amplitude step of 5dB, and a time interval
of 0.5Fs assuming a crystal frequency of 16MHz. This
would produce an ASK pulse that ramps up in 3Fs, levels off for 9.5Fs, and ramps down in 3Fs. Because the
amplitude steps are in decibels, the shape of the pulse
rise and fall is exponential on a linear display (an oscilloscope, for instance). Because most ASK receivers use
a logarithmic amplitude detector, the demodulated pulse
12.5µs
has a linear ramp shape. The digital shaping is disabled
when the Tstep register is 0x00.
If no shaping of any kind is used (digital or analog), the
PA pullup inductor must be connected to PAVOUT and
the analog shaping bits in the Conf0 register must also
be set to either anshp[1:0] = 00 or to anshp[1:0] = 11, as
described in the ASK Envelope Shaping section.
Analog Amplitude Shaping
To use the analog shaping feature, the user must connect the bias inductor to the ROUT pin instead of directly
to the PAVOUT pin. This places a MOS resistor between
PAVOUT and ROUT, which slows down the application of
the PAVOUT voltage to the drain of the PA FET when the
PA is turned on. There are two settings in the anshp[1:0]
bits in the Conf0 register for the rate at which the pulse
ramps up: anshp[1:0] = 10 is approximately 1.5Fs and
anshp[1:0] = 01 is approximately 3Fs. The anshp[1:0] =
11 setting turns analog shaping off and removes the 4Fs
pulse extension, while the anshp[1:0] = 00 setting opens
the connection between PAVOUT and ROUT.
Tuning Capacitor Settings
The internal variable shunt capacitor, which can be used
to match the PA to the antenna with changing transmitter
frequency, is controlled by setting the 5-bit cap variable in the registers. This allows for 32 levels of shunt
capacitance control. Since the control of these 5 bits is
independent of the other settings, any capacitance value
can be chosen at any frequency, making it possible to
maintain maximum transmitter efficiency while moving
rapidly from one frequency to another. The internal tuning capacitor adds 0 to 7.75pF to the PA output in 0.25pF
steps. The PA output capacitance at the minimum cap
setting is approximately 4.5pF.
12.5µs
DIN
PApwr =
0x1E (30dec)
0
PAstep = 0x05 (5dB)
PAstep = 0x05 (5dB)
Tstep = 0x2 (0.5µs)
Tstep = 0x2 (0.5µs)
Figure 7. Digital Amplitude Shaping Timing Diagram
______________________________________________________________________________________ 19
MAX7060
ASK Amplitude Shaping
At data rates higher than 30kbps Manchester (60kbps
NRZ), it may be necessary to shape the ASK transmitter
pulses to reduce the occupied bandwidth of the transmitted signal to comply with government regulations
(FCC in the U.S., ETSI in Europe). There is no shaping
of the FSK modulation. The MAX7060 has two forms of
amplitude shaping: digital and analog.
MAX7060
280MHz to 450MHz Programmable
ASK/FSK Transmitter
Register Details
The following tables provide information on the MAX7060 registers.
Table 1. Register Summary
REGISTER
ADDRESS
DESCRIPTION
Ident
0x00
Read-only register used for identification purpose. The content of this register is always 0xA6.
Conf0
0x01
Configuration 0 register. Controls the GPO1 boost mode, PLL bandwidth, analog shaping, crystal clock output, and the modulation mode (ASK/FSK).
Conf1
0x02
Configuration 1 register. Controls the clock output frequency divider and the capacitance at the
PA output.
Conf2
0x03
Configuration 2 register. Controls the emulation mode.
IOConf0
0x04
IO configuration 0 register. Selects the status register bus for SPI operation.
IOConf1
0x05
IO configuration 1 register. Selects the outputs of GPO1 and GPO2_MOD pins.
Tstep
0x06
Digital shaping time step register. Controls the time step in the digital shaping.
PAstep
0x07
Digital shaping power step register. Controls the power step in the digital shaping.
PApwr
0x08
Final power register. Controls the final output power.
FHigh0
0x09
High-frequency 0 register (upper byte). Sets the high frequency in FSK transmission.
FHigh1
0x0A
High-frequency 1 register (lower byte). Sets the high frequency in FSK transmission.
FCenter0
0x0B
Center-frequency 0 register (upper byte). Sets the carrier frequency in ASK transmission.
FCenter1
0x0C
Center-frequency 1 register (lower byte). Sets the carrier frequency in ASK transmission.
FLow0
0x0D
Low-frequency 0 register (upper byte). Sets the low frequency in FSK transmission.
FLow1
0x0E
Low-frequency 1 register (lower byte). Sets the low frequency in FSK transmission.
FLoad
0x0F
Frequency-load register. Performs the frequency-load function.
EnableReg
0x10
Enable register. Register equivalent of ENABLE pin.
DataReg
0x11
Datain register. Register equivalent of DIN pin.
Status
0x12
Status register
Table 2. Configuration Registers
REGISTER
ADDRESS
DATA
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
Ident
0x00
1
0
1
0
0
1
1
0
R
Conf0
0x01
—
gp1bst
pllbw
anshp_1
anshp_0
clksby
clkout
mode
R/W
Conf1
0x02
ckdiv_2
ckdiv_1
ckdiv_0
cap_4
cap_3
cap_2
cap_1
cap_0
R/W
Conf2
0x03
fixed
fxmode
fxpwr_1
fxpwr_0
fxhdev
fxfrq_2
fxfrq_1
fxfrq_0
R/W
IOConf0
0x04
—
—
—
—
—
tmux_2
tmux_1
tmux_0
R/W
IOConf1
0x05
—
gp2s_2
gp2s_1
gp2s_0
—
gp1s_2
gp1s_1
gp1s_0
R/W
Tstep
0x06
—
—
—
—
tstep_3
tstep_2
tstep_1
tstep_0
R/W
PAstep
0x07
—
—
—
pastp_4
pastp_3
pastp_2
pastp_1
pastp_0
R/W
PApwr
0x08
—
—
—
papwr_4
papwr_3
papwr_2
papwr_1
papwr_0
R/W
FHigh0
0x09
fhi_15
fhi_14
fhi_13
fhi_12
fhi_11
fhi_10
fhi_9
fhi_8
R/W
FHigh1
0x0A
fhi_7
fhi_6
fhi_5
fhi_4
fhi_3
fhi_2
fhi_1
fhi_0
R/W
FCenter0
0x0B
fce_15
fce_14
fce_13
fce_12
fce_11
fce_10
fce_9
fce_8
R/W
FCenter1
0x0C
fce_7
fce_6
fce_5
fce_4
fce_3
fce_2
fce_1
fce_0
R/W
20 �������������������������������������������������������������������������������������
MODE
280MHz to 450MHz Programmable
ASK/FSK Transmitter
REGISTER
ADDRESS
DATA
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
MODE
FLow0
0x0D
flo_15
flo_14
flo_13
flo_12
flo_11
flo_10
flo_9
flo_8
R/W
FLow1
0x0E
flo_7
flo_6
flo_5
flo_4
flo_3
flo_2
flo_1
flo_0
R/W
FLoad
0x0F
—
—
—
—
—
—
—
hop
R/W
EnableReg
0x10
—
—
—
—
—
—
—
enable
R/W
DataReg
0x11
—
—
—
—
—
—
—
datain
R/W
Status
0x12
status_7
status_6
status_5
status_4
status_3
status_2
status_1
status_0
R
Table 3. Identification (Ident) Register (Address: 0x00)
BIT
NAME
7:0
ident
FUNCTION
Read-only register used for identification purpose. The content of this register is always 0xA6.
Table 4. Configuration 0 (Conf0) Register (Address: 0x01)
BIT
NAME
6
gp1bst
5
pllbw
FUNCTION
0 = Normal GPO1 output driver
1 = Extended driving capability on GPO1
PLL bandwidth setting, low (0) = 300kHz or high (1) = 600kHz; 300kHz is recommended for fractional-N
and 600kHz for fixed-N (ASK mode only)
Control time constants of the analog shaping (bias inductor connected to the ROUT pin)
anshp[1:0]
Rise/fall time
00
ROUT open-circuited, 4Fs pulse extension present
01
nominal 3.0Fs rise/fall time
10
nominal 1.5Fs rise/fall time
11
no analog shaping, no 4Fs pulse extension
4:3
anshp[1:0]
2
clksby
Crystal clock output enable (1) while part is in standby mode
1
clkout
Crystal clock output enable (1) on GPO1 output, gp1s[2:0] = 0x2
0
mode
ASK (0) or FSK (1)
Table 5. Configuration 1 (Conf1) Register
(Address: 0x02)
BIT
NAME
FUNCTION
7:5
ckdiv[2:0]
3-bit clock output frequency divider
4:0
cap[4:0]
5-bit capacitor setting
Table 6. Crystal Divide Settings for Clock
Output
ckdiv[2:0]
CRYSTAL FREQUENCY
DIVIDED BY
000
1
001
2
010
4
011
8
1XX
16
______________________________________________________________________________________ 21
MAX7060
Table 2. Configuration Registers (continued)
MAX7060
280MHz to 450MHz Programmable
ASK/FSK Transmitter
Table 7. Configuration 2 (Conf2) Register (Address: 0x03)
BIT
NAME
7
fixed
6
fxmode
5:4
fxpwr[1:0]
3
fxhdev
2:0
fxfrq[2:0]
FUNCTION
Enable (1) or disable (0) emulation mode
FSK (1) or ASK (0)
Output power setting
fxpwr[1:0]
dB below PMAX
00
0
01
3
10
6
11
10
100kHz (1) or 32kHz (0) frequency deviation in FSK
Frequency selection
The combinations are same as those in manual mode. When a 16MHz crystal is used, the following frequency values are selected by fxfrq[2:0].
fxfrq[2:0] Freq (MHz) Divide Ratio
000
N/A
N/A
001
315.00
19.68750
010
433.62
27.10125
011
390.00
24.37500
100
418.00
26.12500
101
372.00
23.25000
110
345.00
21.56250
111
433.92
27.12000
Table 8. IO Configuration 0 (IOConf0) Register (Address: 0x04)
BIT
NAME
2:0
tmux[2:0]
FUNCTION
Status register output selection bits
22 �������������������������������������������������������������������������������������
280MHz to 450MHz Programmable
ASK/FSK Transmitter
BIT
6:4
2:0
NAME
FUNCTION
gp2s[2:0]
GPO2 output selection
CS_DEV
Bit 2
Bit 1
Bit 0
GPO2_MOD
0
X
X
X
SPI Data Output
1
000
lockdet
1
001
—
1
010
ckout
1
011
—
1
100
—
1
101
nock
1
110
—
1
111
—
gp1s[2:0]
GPO1 output selection
Bit 2
Bit 1 Bit 0
GPO1
0
0 0lockdet
0
0 1—
0
1 0ckout
0
1 1—
1
0 0—
1
0 1nock
1
1 0—
1
1 1—
where:
—
Reserved signals
nock
No-clock flag (1) if crystal oscillator is disabled, and (0) if clock activity is observed
ckout
Clock output signal, according to programmed dividers (ckdiv[2:0])
lockdet PLL lock-detect flag
Table 10. ASK Digital Shaping Time Step (Tstep) Register (Address: 0x06)
BIT
NAME
3:0
tstep[3:0]
FUNCTION
Time interval value used in digital shaping, in increments of 4/fXTAL
Table 11. PA Digital Shaping Amplitude Step (PAstep) Register (Address: 0x07)
BIT
NAME
4:0
pastp[4:0]
FUNCTION
Power step in digital shaping, in increments of 1dB
Table 12. PA Power (PApwr) Register (Address: 0x08)
BIT
NAME
4:0
papwr[4:0]
FUNCTION
Final PA output power setting
Table 13. FSK High-Frequency 0 (FHigh0) Register (Address: 0x09)
BIT
NAME
7:0
fhi[15:8]
FUNCTION
8-bit upper byte of high-frequency divider for FSK
______________________________________________________________________________________ 23
MAX7060
Table 9. IO Configuration 1 (IOConf1) Register (Address: 0x05)
MAX7060
280MHz to 450MHz Programmable
ASK/FSK Transmitter
Table 14. FSK High-Frequency 1 (FHigh1) Register (Address: 0x0A)
BIT
NAME
7:0
fhi[7:0]
FUNCTION
8-bit lower byte of high-frequency divider for FSK
The 4 MSBs of FHigh0, fhi[15:12], are the integer portion of the divider, excluding offset of 16. The 12 LSBs (fhi[11:0])
are the fractional part of the divider.
Table 15. ASK Center-Frequency 0 (FCenter0) Register (Address: 0x0B)
BIT
NAME
7:0
fce[15:8]
FUNCTION
8-bit upper byte of frequency divider for ASK
Table 16. ASK Center-Frequency 1 (FCenter1) Register (Address: 0x0C)
BIT
NAME
7:0
fce[7:0]
FUNCTION
8-bit lower byte of frequency divider for ASK
The 4 MSBs of FCenter0, fce[15:12], are the integer portion of the divider, excluding offset of 16. The 12 LSBs (fce[11:0)
are the fractional part of the divider.
When fce[11:0] are all zeros and ASK mode is selected (mode bit = 0), the PLL works in the fixed-N mode, which
reduces current consumption and reference spurs. Set pllbw bit high (Conf0 register, bit 5). For all other combinations,
the PLL works in fractional-N mode.
Table 17. FSK Low-Frequency 0 (FLow0) Register (Address:0x0D)
BIT
NAME
7:0
flo[15:8]
FUNCTION
8-bit upper byte of low-frequency divider for FSK
Table 18. FSK Low-Frequency 1 (FLow1) Register (Address: 0x0E)
BIT
NAME
7:0
flo[7:0]
FUNCTION
8-bit lower byte of low-frequency divider for FSK
The 4 MSBs of FLow0, flo[15:12], are the integer portion of the divider, excluding offset of 16. The 12 LSBs (flo[11:0])
are the fractional part of the divider.
Table 19. Maximum and Minimum Values for Frequency Divider
DECIMAL VALUE
fhi[15:0], fce[15:0], flo[15:0]
12.0220
0xC05A
2.9536
0x2F42
Table 20. Frequency-Load (FLoad) Register (Address: 0x0F)
BIT
NAME
FUNCTION
0
hop
Effectively changes the PLL frequency to the ones written in registers 0x09 to 0x0E. This is a self-reset bit
and is reset to zero after the operation is completed.
24 �������������������������������������������������������������������������������������
280MHz to 450MHz Programmable
ASK/FSK Transmitter
BIT
NAME
0
enable
FUNCTION
SPI equivalent of the ENABLE pin, which should be kept low (0) if the external ENABLE pin is used. The
external ENABLE pin should also be kept low (0) if the enable bit is used.
Table 22. Data Input (DataReg) Register (Address: 0x11)
BIT
NAME
FUNCTION
0
datain
SPI equivalent of DIN, where the transmitted data can be controlled through the SPI interface. It should
be kept low (0) if only the external DIN pin is used. The external DIN pin should also be kept low (0) if the
datain bit is used.
Table 23. Status (Status) Register (Address: 0x12)
BIT
NAME
7:0
status[7:0]
FUNCTION
Read-only status register, selected through tmux[2:0] (register 0x04 IOConf0)
Table 24. Status Bus Signals
tmux[2:0]
0
status[7]
—
status[6]
—
status[5]
—
status[4]
—
status[3]
ckout
status[2]
ckd16
status[1]
ckd4
status[0]
nock
1
—
—
—
2
—
—
—
—
—
—
—
—
—
enable
—
—
—
3
—
frac_fxdb
—
cap[4]
cap[3]
cap[2]
cap[1]
cap[0]
4
—
—
notover
capfxd[4]
capfxd[3]
capfxd[2]
capfxd[1]
capfxd[0]
5
integ[3]
integ[2]
integ[1]
integ[0]
frac[11]
frac[10]
frac[9]
frac[8]
6
frac[7]
frac[6]
frac[5]
frac[4]
frac[3]
frac[2]
frac[1]
frac[0]
7
—
—
—
—
—
—
lockdet
xmit_en
—
Reserved signals
nockNo-clock flag (1) if crystal oscillator is disabled, and (0) ic clock activity is observed
ckd4
Crystal clock signal divided by 4
ckd16 Crystal clock signal divided by 16
frac_fxdbFractional-N mode (1) or ASK fixed-N mode
(0)
capfxd[4:0] Emulation mode variable capacitor setting
notoverASK digital shaping flag (1) when PA power
value is different than 0
ckout
Clock output signal, according to programmed dividers (ckdiv[2:0])
integ[3:0]
Fractional-N 4-bit integer value
frac[11:0]
Fractional-N 12-bit fractional value
enableInternal enable signal (OR function of the
ENABLE pin and enable bit)
xmit_en
Transmitter PA enable flag
lockdet
PLL lock-detect flag
cap[4:0]
SPI mode capacitor setting
______________________________________________________________________________________ 25
MAX7060
Table 21. Enable (EnableReg) Register (Address: 0x10)
MAX7060
280MHz to 450MHz Programmable
ASK/FSK Transmitter
Manual Mode Settings
Frequency Selection
There are seven internally set fractional-N divide ratios
that correspond to commonly used frequencies when a
16MHz crystal is used.
The MAX7060 can be operated by controlling certain
pins directly, thereby eliminating the need for an SPI
controller. There is a restricted selection of frequency
and power settings, but operation is simpler. The pins
that are used in manual mode are as follows:
Notice that the MAX7060 can be operated manually at
any single frequency over its 280MHz to 450MHz operating range by choosing a crystal frequency and one of the
divide ratios from Table 25. For example, a transmitting
frequency of 308MHz can be achieved by selecting the
19.68750 divide ratio and a 15.6444MHz crystal.
Pin 1:GPO2_MOD (modulation mode, 0 = ASK,
1 = FSK)
Pins 5, 6, 7: FREQ0, FREQ1, FREQ2
Pin 19:CS_DEV (FSK deviation selection, 0 = Q16kHz,
1 = Q50kHz)
The frequency settings in the manual mode of operation were designed in a way that allows the customer to
toggle only one control line between low and high states
to switch between seven commonly used frequency
pairs (see Table 26).
Pins 20, 21:SDI_PWR1 and SCLK_PWR0 (2-pin power
selection)
Pins 22, 23: ENABLE and DIN (PA variable capacitor
setting, data input, enable)
ASK or FSK Modulation
Reset pin 1 (GPO2_MOD) to 0 for ASK modulation and
1 for FSK modulation. Analog shaping in ASK mode is
enabled by using the ROUT pin. The turn-on and turn-off
time is fixed at approximately 1µs.
To put the MAX7060 in manual mode, set any of the
FREQ0, FREQ1, FREQ2 pins (5, 6, and 7) to logic-high.
These pins are normally pulled down, so the default
state of the MAX7060 is for SPI operation. The settings in
Table 25 can be made in manual mode.
Table 25. Manual Mode Frequency Selection
FREQ2
FREQ1
FREQ0
FREQUENCY (MHz)
DIVIDE RATIO
0
0
0
SPI
N/A
0
0
1
315.00
19.68750
0
1
0
433.62
27.10125
0
1
1
390.00
24.37500
1
0
0
418.00
26.12500
1
0
1
372.00
23.25000
1
1
0
345.00
21.56250
1
1
1
433.92
27.12000
Table 26. Manual Mode Frequency Pair Switching
LOW FREQUENCY
(MHz)
HIGH FREQUENCY
(MHz)
315.00
433.92
001 to 111. Set FREQ0 high, shorting FREQ1 and FREQ2, toggling 1 line.
418.00
433.92
100 to 111. Set FREQ2 high, shorting FREQ1 and FREQ0, toggling 1 line.
433.62
433.92
010 to 111. Set FREQ1 high, shorting FREQ2 and FREQ0, toggling 1 line.
315.00
390.00
001 to 011. Set FREQ0 high and FREQ2 low, toggling FREQ1.
315.00
372.00
001 to 101. Set FREQ1 low and FREQ0 high, toggling pin FREQ2.
345.00
433.92
110 to 111. Set FREQ2 and FREQ1 high, toggling FREQ0.
390.00
433.92
011 to 111. Set FREQ1 and FREQ0 high, toggling FREQ2.
FREQ2, FREQ1, FREQ0
26 �������������������������������������������������������������������������������������
280MHz to 450MHz Programmable
ASK/FSK Transmitter
SDI_PWR1
SCLK_PWR0
dB BELOW
PMAX
0
0
0
0
1
3
1
0
6
1
1
10
Frequency Deviation
Reset pin 19 (CS_DEV) to 0 for 32kHz (Q16kHz) FSK
deviation and 1 for 100kHz (Q50kHz) FSK deviation.
Transmitter Power
Set SDI_PWR1 (pin 20) and SCLK_PWR0 (pin 21) to four
power settings (relative to the maximum power setting).
Note that at battery voltages below 3V, the top two power
settings are compressed and the power difference is
less than 3dB.
PA Variable Capacitor Setting
In manual mode, capacitance can be added to the PA
output for one selected frequency. This allows the user
to adjust the matching network when switching between
two frequencies in the manual selection table, or for
switching to one frequency that is significantly different
from the others in the table. The user can set the capacitance by resetting the ENABLE pin to a logic-low, then
selecting the frequency for which the variable capacitor
is to be added from the seven possible settings, and
then sending a stream of 1 to 32 pulses through the DIN
pin. The first pulse is used to reset the internal capacitor
counter and to latch the selected frequency. After the first
pulse, the remaining number of pulses sent equals the
variable capacitor setting. When the ENABLE pin goes
high, the capacitor setting for the specified frequency is
set, so that it adds the programmed capacitance to the
PA when the chosen frequency is selected. This scheme
must be executed only once to set the value of the variable capacitor.
For example, a user can operate the MAX7060 at
315MHz and 433.92MHz into a narrowband antenna
by resetting the ENABLE pin low, setting the FREQ0,
FREQ1, FREQ2 pins to 001 (315MHz), and sending the
appropriate number of pulses into the DIN pin, and then
setting the ENABLE pin high. When the frequency is set
to 433.92MHz (or any other frequency in the table except
315MHz), no capacitance is added to the PA output.
When the frequency is set to 315MHz, the PA capacitance increases by the programmed value.
Figure 8 illustrates how to set the capacitance. It begins
with the ENABLE pin pulled low. The frequency is
sampled at the rising edge of the first pulse. Pulses
2–11 set the capacitance code to 0x0A (10dec), which
is approximately 2.5pF. The ENABLE pin is then pulled
high to finish the setting.
Emulation Mode Settings
All the settings available through the manual mode of
operation are also easily accessible in the SPI mode.
This mode is called emulation mode, whereby only writing one or two registers, the whole transmitter can be
configured. The Conf2 register controls this mode.
The emulation mode is a subset of SPI mode. It gives SPI
users the capability to operate the part by programming
just one or two registers instead of all registers.
Since it is still SPI mode, pins 5, 6, and 7 (FREQ0, FREQ1,
and FREQ2) must be pulled low. The Conf2 register is
the only register that needs to be programmed. Setting
bit 7 (fixed) to 1 enables this mode. Bit 6 (fxmode) is
equivalent to pin 1 (GPO2_MOD) in manual mode. Bits
5 and 4 (fxpwr[1:0]) are equivalent to pin 20 and 21
(SDI_PWR1 and SCLK_PWR0) in manual mode. Bit 3
(fxhdev) is equivalent to pin 19 (CS_DEV) in manual
mode. Bits 2, 1, and 0 (fxfrq[2:0]) are equivalent to pins
5, 6, and 7 (FREQ0, FREQ1, and FREQ2) in manual
mode.
Similar to manual mode, the PA capacitor setting in the
emulation mode can be done by toggling the DIN pin
with the ENABLE pin low. In addition, the capacitor setting can also be done by directly writing to the capacitor
register (bits 4:0 of the Conf1 register, cap[4:0]). As long
as the capacitor register value is not zero, the capacitor
value sent in by toggling the DIN pin is ignored.
Control Interface Considerations
When operating the MAX7060 with a +4.5V to +5.5V
supply voltage, the CS_DEV, SCLK_PWR0, SDI_PWR1,
FREQ0, FREQ1, FREQ2, ENABLE, DIN, and LSHDN
pins can be driven by a microcontroller with either 3V or
5V interface logic levels. When operating the MAX7060
with a +2.1V to +3.6V supply, the microcontroller must
produce logic levels that conform to the VIH and VIL
specifications in the DC Electrical Characteristics for the
MAX7060.
______________________________________________________________________________________ 27
MAX7060
Table 27. Output Power Settings
MAX7060
280MHz to 450MHz Programmable
ASK/FSK Transmitter
ENABLE
FREQ[2:0]
X
0x1
DIN
CAP CODE
CAPTURED
CAP VALUE
X
0x0A
Figure 8. Variable Capacitor Setting Timing Diagram
Typical Application Circuits
SPI Mode (5V Supply)
Y1
C1
C2
19
20
21
22
DIGITAL
CONTROLLER
23
24
C4
+3VREG
C3
+5V
C5
18
17
16
XTAL1
XTAL2
AVDD
C7
C6
15
14
C8
13
N.C. VDD5
PAVOUT
ROUT
CS_DEV
12
L1
+3VREG
SDI_PWR1
PAVDD
C9
SCLK_PWR0
MAX7060
ENABLE
PAOUT
EXPOSED PAD
DIN
N.C.
LSHDN
N.C.
FREQ2
GPO2_MOD
1
11
GPO1
DVDD GPOVDD
2
3
+3VREG
C12
4
10
9
Tx
ANTENNA
C10
MATCHING
NETWORK
COMPONENTS
8
7
FREQ0 FREQ1
5
6
C11
+5V
28 �������������������������������������������������������������������������������������
280MHz to 450MHz Programmable
ASK/FSK Transmitter
Manual Mode (3V Supply, Shaped ASK Modulation, 315MHz)
C1
C2
19
20
21
22
23
24
C4
Y1
+3V
+3V
C5
C3
18
17
16
XTAL1
XTAL2
AVDD
C6
15
14
C7
13
N.C. VDD5
PAVOUT
ROUT
CS_DEV
SDI_PWR1
PAVDD
+3V
C8
11
SCLK_PWR0
C9
C10
Tx
ANTENNA
L1
MAX7060
ENABLE
PAOUT
EXPOSED PAD
DIN
N.C.
LSHDN
N.C.
FREQ2
DIGITAL
CONTROLLER
12
GPO2_MOD
GPO1
1
2
DVDD
3
C12
GPOVDD
FREQ0
4
+3V
5
10
9
MATCHING
NETWORK
COMPONENTS
8
7
FREQ1
6
C11
Component List
DESIGNATION
QTY
C1, C4
2
May not be needed for low CLOAD crystals, depending on PCB layout parasitics
C2, C3
2
1.5nF ±10%, 50V X7R ceramic capacitors (0603)
Murata GRM188R71H152K
C5, C6
2
100nF ±10%, 50V X7R ceramic capacitors (0603)
Murata GRM188R71H104K
C7, C8, C9
3
220pF ±5% ceramic capacitors (0603)
Murata GRM1885C1H220JA01D
C10, C11, C12
3
10nF ±10%, 50V X7R ceramic capacitors (0603)
Murata GRM188R71H103K
L1
1
±5% wire-wound inductor (0603)
Murata LQW18 series (value depends on matching network)
4
3 capacitors and 1 inductor (values depend on frequency range and antenna impedance)
1
Maxim MAX7060ATG+
1
16MHz crystal, 10pF CLOAD
Crystek 17466
Suntsu SCX284
Matching Network
Components
U1
Y1
DESCRIPTION
______________________________________________________________________________________ 29
MAX7060
Typical Application Circuits (continued)
MAX7060
280MHz to 450MHz Programmable
ASK/FSK Transmitter
Package Information
Chip Information
PROCESS: CMOS
For the latest package outline information and land patterns
(footprints), go to www.maxim-ic.com/packages. Note that a
“+”, “#”, or “-” in the package code indicates RoHS status only.
Package drawings may show a different suffix character, but
the drawing pertains to the package regardless of RoHS status.
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE
NO.
LAND
PATTERN NO.
24 TQFN-EP
T2444+3
21-0139
90-0021
30 �������������������������������������������������������������������������������������
280MHz to 450MHz Programmable
ASK/FSK Transmitter
REVISION
NUMBER
REVISION
DATE
0
2/10
Initial release
2/12
Power dissipation and derating factor shown for wrong package type;
clarified GPO1 boost mode and nature of analog and digital ASK envelope
shaping. Added paragraph on control interface considerations; updated
Typical Application Circuits to add exposed pad (grounded); and specified
typical load C on crystal in component list
1
DESCRIPTION
PAGES
CHANGED
—
2, 14, 15, 19, 21, 27,
28, 29
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied.
Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical
Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2012 Maxim Integrated Products 31
Maxim is a registered trademark of Maxim Integrated Products, Inc.
MAX7060
Revision History