TI LMV982MM

LMV981,LMV982
LMV981 Single / LMV982 Dual 1.8V, RRIO Operational Amplifiers with Shutdown
Literature Number: SNOS976K
LMV981 Single / LMV982 Dual
1.8V, RRIO Operational Amplifiers with Shutdown
General Description
Features
LMV981/LMV982 are low voltage, low power operational amplifiers. LMV981/LMV982 operate from +1.8V to +5.0V supply
voltages and have rail-to-rail input and output. LMV981/
LMV982 input common mode voltage extends 200mV beyond the supplies which enables user enhanced functionality
beyond the supply voltage range. The output can swing railto-rail unloaded and within 105mV from the rail with 600Ω load
at 1.8V supply. LMV981/LMV982 are optimized to work at
1.8V which make them ideal for portable two-cell battery powered systems and single cell Li-Ion systems.
LMV981/LMV982 offer a shutdown pin that can be used to
disable the device and reduce the supply current. The device
is in shutdown when the SHDN-pin = low. The output will be
high impedance in shutdown.
LMV981/LMV982 exhibit excellent speed-power ratio,
achieving 1.4MHz gain bandwidth product at 1.8V supply
voltage with very low supply current. LMV981/LMV982 are
capable of driving a 600Ω load and up to 1000pF capacitive
load with minimal ringing. LMV981/LMV982 have a high DC
gain of 101dB, making them suitable for low frequency applications.
LMV981 is offered in space saving 6-Bump micro SMD,
SC70-6 and SOT23-6 packages. The 6-Bump micro SMD
package has only a 1.006mm x 1.514mm x 0.945mm footprint. LMV982 is offered in space saving MSOP-10 package.
These small packages are ideal solutions for area constrained PC boards and portable electronics such as cellular
phones and PDAs.
(Typical 1.8V Supply Values; Unless Otherwise Noted)
■ Guaranteed 1.8V, 2.7V and 5V specifications
■ Output swing
80mV from rail
— w/600Ω load
30mV from rail
— w/2kΩ load
200mV beyond rails
■ VCM
100μA
■ Supply current (per channel)
1.4MHz
■ Gain bandwidth product
4.0mV
■ Maximum VOS
101dB
■ Gain w/600Ω load
1.0mm x 1.5mm
■ Ultra tiny package micro SMD
19μs
■ Turn-on time from shutdown
−40°C to 125°C
■ Temperature range
Applications
■
■
■
■
■
■
■
■
Industrial and automotive
Consumer communication
Consumer computing
PDAs
Portable audio
Portable/battery-powered electronic equipment
Supply current monitoring
Battery monitoring
Typical Application
200214h0
© 2010 National Semiconductor Corporation
200214
www.national.com
LMV981 Single / LMV982 Dual 1.8V, RRIO Operational Amplifiers with Shutdown
October 13, 2010
LMV981/LMV982
For soldering specifications:
see product folder at www.national.com and
www.national.com/ms/MS/MS-SOLDERING.pdf
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
ESD Tolerance (Note 2)
Machine Model
Human Body Model
Supply Voltage (V+–V −)
Differential Input Voltage
Voltage at Input/Output Pins
Storage Temperature Range
Junction Temperature (Note 4)
Operating Ratings
(Note 1)
Supply Voltage Range
Temperature Range
200V
2000V
5.5V
± Supply Voltage
V++0.3V, V- -0.3V
−65°C to 150°C
150°C
1.8V to 5.0V
−40°C to 125°C
Thermal Resistance (θJA)
6-Bump micro SMD
SC70-6
SOT23-6
MSOP-10
286°C/W
414°C/W
265°C/W
235°C/W
1.8V DC Electrical Characteristics
Unless otherwise specified, all limits guaranteed for TJ = 25°C. V+ = 1.8V, V − = 0V, VCM = V+/2, VO = V+/2,
RL > 1 MΩ and SHDN tied to V+. Boldface limits apply at the temperature extremes. See (Note 10).
Symbol
VOS
Parameter
Input Offset Voltage
Condition
Min
(Note 6)
Typ
(Note 5)
Max
(Note 6)
LMV981 (Single)
1
4
6
LMV982 (Dual)
1
5.5
7.5
Units
mV
TCVOS
Input Offset Voltage Average
Drift
5.5
IB
Input Bias Current
15
35
50
nA
IOS
Input Offset Current
13
25
40
nA
IS
Supply Current (per channel)
103
185
205
LMV981 (Single)
0.156
1
2
LMV982 (Dual)
0.178
3.5
5
In Shutdown
CMRR
Common Mode Rejection Ratio LMV981, 0 ≤ VCM ≤ 0.6V
60
55
78
LMV982, 0 ≤ VCM ≤ 0.6V
55
50
76
−0.2V ≤ VCM ≤ 0V
50
72
75
70
100
TA = 25°C
V− −0.2
−0.2 to 2.1
TA = 125°C
V−
1.4V ≤ VCM ≤ 1.8V
(Note 8)
1.4V ≤ VCM ≤ 1.8V (Note 8)
μV/°C
μA
dB
1.8V ≤ VCM ≤ 2.0V
PSRR
Power Supply Rejection Ratio
1.8V ≤ V+ ≤ 5V
CMVR
Input Common-Mode Voltage
Range
For CMRR
www.national.com
Range ≥ 50dB TA = −40°C to 85°C
2
V−
+0.2
dB
V+ +0.2
V+
V+ −0.2
V
AV
Parameter
Large Signal Voltage Gain
LMV981 (Single)
Large Signal Voltage Gain
LMV982 (Dual)
VO
Output Swing
Condition
Min
(Note 6)
Typ
(Note 5)
RL = 600Ω to 0.9V,
VO = 0.2V to 1.6V, VCM = 0.5V
77
73
101
RL = 2kΩ to 0.9V,
VO = 0.2V to 1.6V, VCM = 0.5V
80
75
105
RL = 600Ω to 0.9V,
VO = 0.2V to 1.6V, VCM = 0.5V
75
72
90
RL = 2kΩ to 0.9V,
VO = 0.2V to 1.6V, VCM = 0.5V
78
75
100
1.65
1.63
1.72
RL = 600Ω to 0.9V
VIN = ± 100mV
0.077
1.75
1.74
RL = 2kΩ to 0.9V
VIN = ± 100mV
Output Short Circuit Current
(Note 3)
Sourcing, VO = 0V
VIN = 100mV
4
3.3
8
Sinking, VO = 1.8V
VIN = −100mV
7
5
9
Ton
Turn-on Time from Shutdown
19
VSHDN
Turn-on Voltage to enable part
1.0
Turn-off Voltage
0.55
Units
dB
dB
0.105
0.120
1.77
0.024
IO
Max
(Note 6)
V
0.035
0.04
mA
μs
V
1.8V AC Electrical Characteristics
Unless otherwise specified, all limits guaranteed for TJ = 25°C. V+ = 1.8V, V − = 0V, VCM = V+/2, VO = V+/2,
RL > 1 MΩ and SHDN tied to V+. Boldface limits apply at the temperature extremes. See (Note 10).
Symbol
Parameter
Conditions
Min
(Note 6)
(Note 7)
Typ
(Note 5)
Max
(Note 6)
Units
SR
Slew Rate
0.35
V/μs
GBW
Gain-Bandwidth Product
1.4
MHz
Φm
Phase Margin
67
deg
Gm
Gain Margin
7
dB
en
Input-Referred Voltage Noise
f = 10 kHz, VCM = 0.5V
in
Input-Referred Current Noise
f = 10 kHz
0.08
THD
Total Harmonic Distortion
f = 1kHz, AV = +1
0.023
60
%
RL = 600Ω, VIN = 1 VPP
Amp-to-Amp Isolation
(Note 9)
123
dB
2.7V DC Electrical Characteristics
Unless otherwise specified, all limits guaranteed for TJ = 25°C. V+ = 2.7V, V − = 0V, VCM = V+/2, VO = V+/2,
RL > 1 MΩ and SHDN tied to V+. Boldface limits apply at the temperature extremes. See (Note 10).
Symbol
VOS
Parameter
Input Offset Voltage
Condition
Typ
(Note 5)
Max
(Note 6)
LMV981 (Single)
1
4
6
mV
LMV982 (Dual)
1
6
7.5
mV
3
Min
(Note 6)
Units
www.national.com
LMV981/LMV982
Symbol
LMV981/LMV982
Symbol
Parameter
Condition
Min
(Note 6)
Typ
(Note 5)
Max
(Note 6)
Units
TCVOS
Input Offset Voltage Average
Drift
5.5
IB
Input Bias Current
15
35
50
nA
IOS
Input Offset Current
8
25
40
nA
IS
Supply Current (per channel)
105
190
210
LMV981 (Single)
0.061
1
2
LMV982 (Dual)
0.101
3.5
5
In Shutdown
CMRR
Common Mode Rejection Ratio LMV981, 0 ≤ VCM ≤ 1.5V
60
55
81
LMV982, 0 ≤ VCM ≤ 1.5V
55
50
80
−0.2V ≤ VCM ≤ 0V
50
74
75
70
100
TA = 25°C
V− −0.2
−0.2 to 3.0
TA = 125°C
V−
2.3V ≤ VCM ≤ 2.7V (Note 8)
2.3V ≤ VCM ≤ 2.7V (Note 8)
μV/°C
μA
dB
2.7V ≤ VCM ≤ 2.9V
PSRR
Power Supply Rejection Ratio
1.8V ≤ V+ ≤ 5V
VCM = 0.5V
CMVR
Input Common-Mode Voltage
Range
For CMRR
AV
Large Signal Voltage Gain
LMV981(Single)
Large Signal Voltage Gain
LMV982 (Dual)
VO
Output Swing
Range ≥ 50dB TA = −40°C to 85°C
V+
+0.2
V
87
86
104
RL = 2kΩ to 1.35V,
VO = 0.2V to 2.5V
92
91
110
RL = 600Ω to 1.35V,
VO = 0.2V to 2.5V
78
75
90
RL = 2kΩ to 1.35V,
VO = 0.2V to 2.5V
81
78
100
RL = 600Ω to 1.35V
VIN = ±100mV
2.55
2.53
2.62
0.083
2.65
2.64
Output Short Circuit Current
(Note 3)
Sourcing, VO = 0V
VIN = 100mV
20
15
30
Sinking, VO = 0V
VIN = −100mV
18
12
25
Ton
Turn-on Time from Shutdown
12.5
VSHDN
Turn-on Voltage to enable part
1.9
Turn-off Voltage
0.8
www.national.com
4
V
+−0.2
dB
0.110
0.130
2.675
0.025
IO
V ++0.2
V−
RL = 600Ω to 1.35V,
VO = 0.2V to 2.5V
RL = 2kΩ to 1.35V
VIN = ±100mV
dB
V
0.04
0.045
mA
μs
V
Unless otherwise specified, all limits guaranteed for TJ = 25°C. V+ = 2.7V, V − = 0V, VCM = 1.0V, VO = 1.35V,
RL > 1 MΩ and SHDN tied to V+. Boldface limits apply at the temperature extremes. See (Note 10).
Symbol
Parameter
Conditions
SR
Slew Rate
GBW
Φm
Gm
Gain Margin
en
Input-Referred Voltage Noise
f = 10 kHz, VCM = 0.5V
in
Input-Referred Current Noise
f = 10 kHz
THD
Total Harmonic Distortion
f = 1kHz, AV = +1
Min
(Note 6)
(Note 7)
Typ
(Note 5)
Max
(Note 6)
Units
0.4
V/µs
Gain-Bandwidth Product
1.4
MHz
Phase Margin
70
deg
7.5
dB
57
0.08
RL = 600Ω, VIN = 1VPP
Amp-to-Amp Isolation
(Note 9)
0.022
%
123
dB
5V DC Electrical Characteristics
Unless otherwise specified, all limits guaranteed for TJ = 25°C. V+ = 5V, V − = 0V, VCM = V+/2, VO = V+/2,
RL > 1 MΩ and SHDN tied to V+. Boldface limits apply at the temperature extremes. See (Note 10).
Symbol
VOS
Parameter
Input Offset Voltage
Condition
Min
(Note 6)
Typ
(Note 5)
Max
(Note 6)
LMV981 (Single)
1
4
6
LMV982 (Dual)
1
5.5
7.5
Units
mV
TCVOS
Input Offset Voltage Average
Drift
5.5
IB
Input Bias Current
14
35
50
nA
IOS
Input Offset Current
9
25
40
nA
IS
Supply Current (per Channel)
116
210
230
μA
LMV981 (Single)
0.201
1
2
LMV982 (Dual)
0.302
3.5
5
In Shutdown
CMRR
Common Mode Rejection Ratio 0 ≤ VCM ≤ 3.8V
60
55
86
−0.2V ≤ VCM ≤ 0V
50
78
75
70
100
V− −0.2
−0.2 to 5.3
4.6V ≤ VCM ≤ 5.0V (Note 8)
μV/°C
μA
dB
5.0V ≤ VCM ≤ 5.2V
PSRR
Power Supply Rejection Ratio
1.8V ≤ V+ ≤ 5V
VCM = 0.5V
CMVR
Input Common-Mode Voltage
Range
For CMRR
TA = 25°C
Range ≥ 50dB TA = −40°C to 85°C
TA = 125°C
5
dB
V+ +0.2
V−
V+
V− +0.3
V+ −0.3
V
www.national.com
LMV981/LMV982
2.7V AC Electrical Characteristics
LMV981/LMV982
Symbol
AV
Parameter
Large Signal Voltage Gain
(LMV981 Single)
Large Signal Voltage Gain
LMV982 (Dual)
VO
Output Swing
Condition
Min
(Note 6)
Typ
(Note 5)
RL = 600Ω to 2.5V,
VO = 0.2V to 4.8V
88
87
102
RL = 2kΩ to 2.5V,
VO = 0.2V to 4.8V
94
93
113
RL = 600Ω to 2.5V,
VO = 0.2V to 4.8V
81
78
90
RL = 2kΩ to 2.5V,
VO = 0.2V to 4.8V
85
82
100
4.855
4.835
4.890
RL = 600Ω to 2.5V
VIN = ±100mV (Note 8)
0.120
4.945
4.935
RL = 2kΩ to 2.5V
VIN = ±100mV
Output Short Circuit Current
(Note 3)
LMV981, Sourcing, VO = 0V
VIN = 100mV
80
68
100
Sinking, VO = 5V
VIN = −100mV
58
45
65
Ton
Turn-on Time from Shutdown
8.4
VSHDN
Turn-on Voltage to enable part
4.2
Turn-off Voltage
0.8
Units
dB
dB
0.160
0.180
4.967
0.037
IO
Max
(Note 6)
V
0.065
0.075
mA
μs
V
5V AC Electrical Characteristics
Unless otherwise specified, all limits guaranteed for TJ = 25°C. V+ = 5V, V − = 0V, VCM = V+/2, VO = 2.5V,
R L > 1 MΩ and SHDN tied to V+.Boldface limits apply at the temperature extremes. See (Note 10).
Symbol
Parameter
Conditions
(Note 7)
Min
(Note 6)
Typ
(Note 5)
Max
(Note 6)
Units
SR
Slew Rate
0.42
V/µs
GBW
Gain-Bandwidth Product
1.5
MHz
Φm
Phase Margin
71
deg
Gm
Gain Margin
8
dB
en
Input-Referred Voltage Noise
f = 10 kHz, VCM = 1V
in
Input-Referred Current Noise
f = 10 kHz
0.08
THD
Total Harmonic Distortion
f = 1kHz, AV = +1
0.022
%
123
dB
50
RL = 600Ω, VO = 1V PP
Amp-to-Amp Isolation
www.national.com
(Note 9)
6
Note 2: Human Body Model, applicable std. MIL-STD-883, Method 3015.7. Machine Model, applicable std. JESD22-A115-A (ESD MM std. of JEDEC)
Field-Induced Charge-Device Model, applicable std. JESD22-C101-C (ESD FICDM std. of JEDEC).
Note 3: Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in exceeding the
maximum allowed junction temperature of 150°C. Output currents in excess of 45mA over long term may adversely affect reliability.
Note 4: The maximum power dissipation is a function of TJ(MAX) , θJA, and TA. The maximum allowable power dissipation at any ambient temperature is
PD = (TJ(MAX)–T A)/θJA. All numbers apply for packages soldered directly into a PC board.
Note 5: Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will
also depend on the application and configuration. The typical values are not tested and are not guaranteed on shipped production material.
Note 6: All limits are guaranteed by testing or statistical analysis.
Note 7: Connected as voltage follower with input step from V− to V+. Number specified is the slower of the positive and negative slew rates.
Note 8: For guaranteed temperature ranges, see Input Common-Mode Voltage Range specifications.
Note 9: Input referred, RL = 100kΩ connected to V+/2. Each amp excited in turn with 1kHz to produce VO = 3VPP. (For Supply Voltages <3V, VO = V+).
Note 10: Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very limited self-heating
of the device such that TJ = TA. No guarantee of parametric performance is indicated in the electrical tables under conditions of internal self heating where TJ >
TA. See Applications section for information on temperature derating of this device. Absolute Maximum Ratings indicated junction temperature limits beyond which
the device may be permanently degraded, either mechanically or electrically.
Connection Diagrams
6-Bump micro SMD
6-Pin SC70-6/SOT23-6
10-Pin MSOP
200214g7
Top View
20021435
200214g6
Top View
Top View
Ordering Information
Package
Part Number
Packaging Marking
Transport Media
NSC Drawing
6-Bump micro SMD
(NOPB)
LMV981TL
H
250 Units Tape and Reel
TLA06BBA
LMV981TLX
6-Pin SC70
LMV981MG
3k Units Tape and Reel
A77
1k Units Tape and Reel
LMV981MGX
6-Pin SOT23
LMV981MF
A78A
1k Units Tape and Reel
LMV981MFX
10-Pin MSOP
LMV982MM
MA006A
3k Units Tape and Reel
MF06A
3.5k Units Tape and Reel
A87A
1k Units Tape and Reel
LMV982MMX
MUB10A
3.5k Units Tape and Reel
7
www.national.com
LMV981/LMV982
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics.
LMV981/LMV982
Typical Performance Characteristics
Unless otherwise specified, VS = +5V, single supply, TA = 25°C.
Supply Current vs. Supply Voltage (LMV981)
Sourcing Current vs. Output Voltage
20021425
20021422
Sinking Current vs. Output Voltage
Output Voltage Swing vs. Supply Voltage
20021428
20021449
Output Voltage Swing vs. Supply Voltage
Gain and Phase vs. Frequency
20021450
www.national.com
200214g8
8
LMV981/LMV982
Gain and Phase vs. Frequency
Gain and Phase vs. Frequency
200214g9
200214g10
Gain and Phase vs. Frequency
CMRR vs. Frequency
20021439
200214g11
PSRR vs. Frequency
Input Voltage Noise vs. Frequency
20021456
20021458
9
www.national.com
LMV981/LMV982
Input Current Noise vs. Frequency
THD vs. Frequency
20021466
20021467
THD vs. Frequency
Slew Rate vs. Supply Voltage
20021469
20021468
Small Signal Non-Inverting Response
Small Signal Non-Inverting Response
20021470
www.national.com
20021471
10
Large Signal Non-Inverting Response
20021473
20021472
Large Signal Non-Inverting Response
Large Signal Non-Inverting Response
20021474
20021475
Short Circuit Current vs. Temperature (Sinking)
Short Circuit Current vs. Temperature (Sourcing)
20021476
20021477
11
www.national.com
LMV981/LMV982
Small Signal Non-Inverting Response
LMV981/LMV982
Offset Voltage vs. Common Mode Range
Offset Voltage vs. Common Mode Range
20021436
20021437
Offset Voltage vs. Common Mode Range
20021438
pendent spurious signal in series with the input signal and can
effectively degrade small signal parameters such as gain and
common mode rejection ratio. To resolve this problem, the
small signal should be placed such that it avoids the VOS
crossover point. In addition to the rail-to-rail performance, the
output stage can provide enough output current to drive
600Ω loads. Because of the high current capability, care
should be taken not to exceed the 150°C maximum junction
temperature specification.
Application Note
INPUT AND OUTPUT STAGE
The rail-to-rail input stage of this family provides more flexibility for the designer. The LMV981/LMV982 use a complimentary PNP and NPN input stage in which the PNP stage
senses common mode voltage near V− and the NPN stage
senses common mode voltage near V+. The transition from
the PNP stage to NPN stage occurs 1V below V+. Since both
input stages have their own offset voltage, the offset of the
amplifier becomes a function of the input common mode voltage and has a crossover point at 1V below V+.
This VOS crossover point can create problems for both DC and
AC coupled signals if proper care is not taken. Large input
signals that include the VOS crossover point will cause distortion in the output signal. One way to avoid such distortion is
to keep the signal away from the crossover. For example, in
a unity gain buffer configuration and with VS = 5V, a 5V peakto-peak signal will contain input-crossover distortion while a
3V peak-to-peak signal centered at 1.5V will not contain inputcrossover distortion as it avoids the crossover point. Another
way to avoid large signal distortion is to use a gain of −1 circuit
which avoids any voltage excursions at the input terminals of
the amplifier. In that circuit, the common mode DC voltage
can be set at a level away from the VOS cross-over point. For
small signals, this transition in VOS shows up as a VCM dewww.national.com
SHUTDOWN MODE
The LMV981/LMV982 have a shutdown pin. To conserve battery life in portable applications, the LMV981/LMV982 can be
disabled when the shutdown pin voltage is pulled low.
The shutdown pin can’t be left unconnected. In case shutdown operation is not needed, the shutdown pin should be
connected to V+ when the LMV981/LMV982 are used. Leaving the shutdown pin floating will result in an undefined operation mode, either shutdown or active, or even oscillating
between the two modes.
INPUT BIAS CURRENT CONSIDERATION
The LMV981/LMV982 family has a complementary bipolar
input stage. The typical input bias current (IB) is 15nA. The
input bias current can develop a significant offset voltage.
This offset is primarily due to IB flowing through the negative
12
tion because the common mode input range goes up to the
rail.
200214h0
FIGURE 2. High Side Current Sensing
HALF-WAVE RECTIFIER WITH RAIL-TO-GROUND
OUTPUT SWING
Since the LMV981/LMV982 input common mode range includes both positive and negative supply rails and the output
can also swing to either supply, achieving half-wave rectifier
functions in either direction is an easy task. All that is needed
are two external resistors; there is no need for diodes or
matched resistors. The half wave rectifier can have either
positive or negative going outputs, depending on the way the
circuit is arranged.
In Figure 3 the circuit is referenced to ground, while in Figure
4 the circuit is biased to the positive supply. These configurations implement the half wave rectifier since the LMV981/
LMV982 can not respond to one-half of the incoming waveform. It can not respond to one-half of the incoming because
the amplifier can not swing the output beyond either rail therefore the output disengages during this half cycle. During the
other half cycle, however, the amplifier achieves a half wave
that can have a peak equal to the total supply voltage. RI
should be large enough not to load the LMV981/LMV982.
20021459
FIGURE 1. Canceling the Offset Voltage due to Input Bias
Current
Typical Applications
HIGH SIDE CURRENT SENSING
The high side current sensing circuit (Figure 2) is commonly
used in a battery charger to monitor charging current to prevent over charging. A sense resistor RSENSE is connected to
the battery directly. This system requires an op amp with railto-rail input. The LMV981/LMV982 are ideal for this applica-
200214c4
200214c2
200214c3
FIGURE 3. Half-Wave Rectifier with Rail-To-Ground Output Swing Referenced to Ground
13
www.national.com
LMV981/LMV982
feedback resistor, RF. For example, if IB is 50nA and RF is
100kΩ, then an offset voltage of 5mV will develop (VOS = IB x
RF). Using a compensation resistor (RC), as shown in Figure
1, cancels this effect. But the input offset current (IOS) will still
contribute to an offset voltage in the same manner.
LMV981/LMV982
200214c1
200214b9
200214c0
FIGURE 4. Half-Wave Rectifier with Negative-Going Output Referenced to VCC
the input and output are only limited by the supply voltages.
Remember that even with rail-to-rail outputs, the output can
not swing past the supplies so the combined common mode
voltages plus the signal should not be greater that the supplies or limiting will occur. For additional applications, see
National Semiconductor application notes AN–29, AN–31,
AN–71, and AN–127.
INSTRUMENTATION AMPLIFIER WITH RAIL-TO-RAIL
INPUT AND OUTPUT
Some manufactures make a non-“rail-to-rail”-op amp rail-torail by using a resistive divider on the inputs. The resistors
divide the input voltage to get a rail-to-rail input range. The
problem with this method is that it also divides the signal, so
in order to get the obtained gain, the amplifier must have a
higher closed loop gain. This raises the noise and drift by the
internal gain factor and lowers the input impedance. Any mismatch in these precision resistors reduces the CMRR as well.
The LMV981/LMV982 is rail-to-rail and therefore doesn’t
have these disadvantages.
Using three of the LMV981/LMV982 amplifiers, an instrumentation amplifier with rail-to-rail inputs and outputs can be made
as shown in Figure 5.
In this example, amplifiers on the left side act as buffers to the
differential stage. These buffers assure that the input
impedance is very high and require no precision matched resistors in the input stage. They also assure that the difference
amp is driven from a voltage source. This is necessary to
maintain the CMRR set by the matching R1-R2 with R3-R4.
The gain is set by the ratio of R2/R1 and R3 should equal R1
and R4 equal R2. With both rail-to-rail input and output ranges,
www.national.com
200214g4
FIGURE 5. Rail-to-rail instrumentation amplifier
14
LMV981/LMV982
Simplified Schematic
200214a9
15
www.national.com
LMV981/LMV982
Physical Dimensions inches (millimeters) unless otherwise noted
NOTES: UNLESS OTHERWISE SPECIFIED
1. EPOXY COATING
2. FOR SOLDER BUMP COMPOSITION, SEE “SOLDER INFORMATION” IN THE PACKAGING SECTION OF THE NATATION SEMICONDUCTOR WEB PAGE
(www.national.com)
3. RECOMMEND NON-SOLDER MASK DEFINED LANDING PAD.
4. PIN A1 IS ESTABLISHED BY LOWER LEFT CORNER WITH RESPECT TO TEXT ORIENTATION.
5. XXX IN DRAWING NUMBER REPRESENTS PACKAGE SIZE VARIATION WHERE X1 IS PACKAGE WIDTH, X2 IS PACKAGE LENGTH AND X3 IS PACKAGE HEIGHT.
6. REFERENCE JEDEC REGISTRATION MO-211, VARIATION DB.
6-Bump micro SMD
NS Package Number TLA06BBA
X1 = 1.031 ±0.030mm X2 = 1.539 ±0.030mm X3 = 0.600 ±0.075mm
6-Pin SC70
NS Package Number MAA06A
www.national.com
16
LMV981/LMV982
6-Pin SOT23
NS Package Number MF06A
10-Pin MSOP
NS Package Number MUB10A
17
www.national.com
LMV981 Single / LMV982 Dual 1.8V, RRIO Operational Amplifiers with Shutdown
Notes
For more National Semiconductor product information and proven design tools, visit the following Web sites at:
www.national.com
Products
Design Support
Amplifiers
www.national.com/amplifiers
WEBENCH® Tools
www.national.com/webench
Audio
www.national.com/audio
App Notes
www.national.com/appnotes
Clock and Timing
www.national.com/timing
Reference Designs
www.national.com/refdesigns
Data Converters
www.national.com/adc
Samples
www.national.com/samples
Interface
www.national.com/interface
Eval Boards
www.national.com/evalboards
LVDS
www.national.com/lvds
Packaging
www.national.com/packaging
Power Management
www.national.com/power
Green Compliance
www.national.com/quality/green
Switching Regulators
www.national.com/switchers
Distributors
www.national.com/contacts
LDOs
www.national.com/ldo
Quality and Reliability
www.national.com/quality
LED Lighting
www.national.com/led
Feedback/Support
www.national.com/feedback
Voltage References
www.national.com/vref
Design Made Easy
www.national.com/easy
www.national.com/powerwise
Applications & Markets
www.national.com/solutions
Mil/Aero
www.national.com/milaero
PowerWise® Solutions
Serial Digital Interface (SDI) www.national.com/sdi
Temperature Sensors
www.national.com/tempsensors SolarMagic™
www.national.com/solarmagic
PLL/VCO
www.national.com/wireless
www.national.com/training
PowerWise® Design
University
THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION
(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY
OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO
SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,
IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS
DOCUMENT.
TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT
NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL
PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR
APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND
APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE
NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.
EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO
LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE
AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR
PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY
RIGHT.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and
whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected
to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform
can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other
brand or product names may be trademarks or registered trademarks of their respective holders.
Copyright© 2010 National Semiconductor Corporation
For the most current product information visit us at www.national.com
National Semiconductor
Americas Technical
Support Center
Email: [email protected]
Tel: 1-800-272-9959
www.national.com
National Semiconductor Europe
Technical Support Center
Email: [email protected]
National Semiconductor Asia
Pacific Technical Support Center
Email: [email protected]
National Semiconductor Japan
Technical Support Center
Email: [email protected]
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and Automotive www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
www.ti.com/video
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated