TGV2204-FC 19 GHz VCO with Prescaler Key Features • • • • • • • • Measured Performance Bias conditions: Vcc = 5 V, Itotal = 165 mA Frequency Range: 18.5 – 19.5 GHz Output Power: 7 dBm @ 19 GHz Phase Noise: -105 dBc/Hz at 1 MHz offset, fc=19 GHz Prescaler Output Freq Range : 2.31 – 2.44 GHz Prescaler Output Power: -6 dBm Bias: Vcc = 5 V, Itotal = 165 mA Typical Technology: HBT3 Chip Dimensions: 1.28 x 1.71 x 0.38 mm Primary Applications • Automotive Radar Product Description The TriQuint TGV2204-FC is a flip-chip voltage controlled oscillator (VCO) designed to operate at frequencies that target the automotive Radar market. The TGV2204-FC is designed using TriQuint’s proven HBT3 process and front-side Cu / Sn pillar technology for simplified assembly and low interconnect inductance. The TGV2204-FC is a VCO that typically provides 7 dBm output power at 19 GHz with < -105 dBc/Hz phase noise at 1 MHz offset . The integrated divide-by-8 prescaler eases PLL design. The TGV2204-FC is an excellent choice for applications requiring frequency stability in transmit chain architectures. The TGV2204-FC has a protective surface passivation layer providing environmental robustness. Lead-free and RoHS compliant. 1 TriQuint Semiconductor: www. triquint.com (972)994-8465 Fax (972)994-8504 [email protected] November 2009 © Rev D TGV2204-FC Table I Absolute Maximum Ratings 1/ Symbol Value Notes Collector Voltage 11 V 2/ Vtune Tune Voltage 11 V Itotal Collector Current Vcc Parameter 276 mA 2/ 1/ These ratings represent the maximum operable values for this device. Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device and / or affect device lifetime. These are stress ratings only, and functional operation of the device at these conditions is not implied. 2/ Combinations of supply voltage, supply current shall not exceed the maximum power dissipation listed in Table IV. Table II Recommended Operating Conditions Symbol 1/ Parameter 1/ Value Vcc Collector Voltage 5 V ± 5% Itotal Collector Current 165 mA Vtune VCO Freq Tune Voltage 0-8 V See assembly diagram for bias instructions. 2 TriQuint Semiconductor: www. triquint.com (972)994-8465 Fax (972)994-8504 [email protected] November 2009 © Rev D TGV2204-FC Table III RF Characterization Table Bias: Vcc = 5 V, Itotal = 165 mA, typical SYMBOL RF Out PARAMETER TEST CONDITIONS MINIMUM NOMINAL MAXIMUM UNITS 5 7 13 dBm Output Power f = 19 – 19.25 GHz PN Phase Noise @ 1 MHz Offset f = 19 – 19.25 GHz F/8 Pout 1/ Prescaler Output Power 1/ f = 19 – 19.25 GHz F/8 Freq Prescaler Output Frequency f = 19 – 19.25 GHz Fout 2V Output Frequency, Vtune = 2 V 18.6 18.95 19.2 GHz Fout 8V Output Frequency, Vtune = 8 V 19.4 19.56 20.0 GHz 1/ -107 -11 -6 dBc/Hz 2 2.31 – 2.44 dBm GHz Single-ended output power measurement 3 TriQuint Semiconductor: www. triquint.com (972)994-8465 Fax (972)994-8504 [email protected] November 2009 © Rev D TGV2204-FC Table IV Power Dissipation and Thermal Properties Parameter Test Conditions Value Notes 1/ 2/ Maximum Power Dissipation Tbaseplate = 70 ºC Pd = TBD W Tjunction = TBD ºC Tm = TBD Hrs Thermal Resistance, θjc Vcc= 5 V Id = 165 mA Pd = 0.825 W Tbaseplate = 70 ºC θjc = 80.4 (ºC/W) Tjunction = 133.5 ºC Tm = TBD Hrs 1/ Mounting Temperature Refer to Solder Reflow Profiles (pp 11) Storage Temperature -65 to 150 ºC For a median life of 1E+6 hours, Power Dissipation is limited to Pd(max) = (150 ºC – Tbase ºC)/θjc. Junction operating temperature will directly affect the device median time to failure (MTTF). For maximum life, it is recommended that junction temperatures be maintained at the lowest possible levels. Median Lifetime (Tm) vs Channel Temperature 1.E+13 1.E+12 Median Lifetime (Hours) 2/ 1.E+11 1.E+10 1.E+09 1.E+08 1.E+07 1.E+06 1.E+05 1.E+04 FET11 25 50 75 100 125 150 175 200 Channel Temperature (°C) 4 TriQuint Semiconductor: www. triquint.com (972)994-8465 Fax (972)994-8504 [email protected] November 2009 © Rev D TGV2204-FC Measured Data on Face-down (flipped) Die on Carrier Board Bias conditions: Vcc = 5 V, Itotal = 165 mA 5 TriQuint Semiconductor: www. triquint.com (972)994-8465 Fax (972)994-8504 [email protected] November 2009 © Rev D TGV2204-FC Measured Data on Face-down (flipped) Die on Carrier Board Bias conditions: Vcc = 5 V, Itotal = 165 mA 6 TriQuint Semiconductor: www. triquint.com (972)994-8465 Fax (972)994-8504 [email protected] November 2009 © Rev D TGV2204-FC Electrical Schematic F/8+ Out F/8Out ~ ÷8 Prescaler RF Out VCO TGV2204-FC 100 pF Vcc 100 pF Vtune Bias Procedures Bias-up Procedure Bias-down Procedure Vtune set to ~ +2 V (for desired Freq) Reduce Vcc to 0 V. Vcc set to 5 V ± 5% Turn Vtune to 0 V For single-ended use of the prescaler (F/8+), the F/8- output pin may be left open 7 TriQuint Semiconductor: www. triquint.com (972)994-8465 Fax (972)994-8504 [email protected] November 2009 © Rev D TGV2204-FC Mechanical Drawing Drawing is for chip face-up Units: millimeters Thickness: 0.38 Die x,y size tolerance: +/- 0.050 Chip edge to pillar dimensions are shown to center of pillar Pillar #4, 7, 10, 12-15 Pillar #1, 3 DC Ground 0.075 ϕ Pillar #6 Prescaler Out (F/8+) 0.075 ϕ RF CPW Ground 0.075 ϕ Pillar #8 Vtune 0.075 ϕ Pillar #2 RF Out 0.075 ϕ Pillar #9 Vbb (Not Used) 0.075 ϕ Pillar #5 Prescaler Out (F/8-) 0.075 ϕ Pillar #11 Vcc 0.075 ϕ GaAs MMIC devices are susceptible to damage from Electrostatic Discharge. Proper precautions should be observed during handling, assembly and test. 8 TriQuint Semiconductor: www. triquint.com (972)994-8465 Fax (972)994-8504 [email protected] November 2009 © Rev D TGV2204-FC Recommended Assembly Diagram Alumina substrate board Thickness: 0.38 mm εr = 9.9 Prescaler F/8- Output Prescaler F/8+ Output RF Gnd RFout RF Gnd TGV2204-FC Die (flip-chip bonded) DC Ground 100 pF Vtune 100 pF TGV2204-FC data represented in this datasheet was taken using coplanar waveguide (CPW) transition on the substrate and ground-signalground probes Vcc Die is flip-chip bonded / bumped to carrier NOTE: Vcc should be bypassed sufficiently to avoid phase noise degradation. Bypass capacitors of 1 uF and 470 uF are recommended. Tuning port should also be free of supply noise. GaAs MMIC devices are susceptible to damage from Electrostatic Discharge. Proper precautions should be observed during handling, assembly and test. TriQuint Semiconductor: www. triquint.com (972)994-8465 Fax (972)994-8504 [email protected] November 2009 © Rev D 9 TGV2204-FC Assembly Notes Component placement and die attach assembly notes: • Vacuum pencils and/or vacuum collets are the preferred method of pick up. • Air bridges must be avoided during placement. • Cu pillars on die are 65 um tall with a 22 um tall Sn solder cap. • Recommended board metallization is evaporated TiW followed by nickel/gold at pillar attach interface. Ni is the adhesion layer for the solder and the gold keeps the Ni from oxidizing. The Au should be kept to a minimum to avoid embrittlement; suggested Au / Sn mass ratio must not exceed 8%. • Au metallization is not recommended on traces due to solder wicking and consumption concerns. If Au traces are used, a physical solder barrier must be applied or designed into the pad area of the board. The barrier must be sufficient to keep the solder from undercutting the barrier. Reflow process assembly notes: • Minimum alloying temperatures 245 C. • Repeating reflow cycles is not recommended due to Sn consumption on the first reflow cycle. • An alloy station or conveyor furnace with an inert atmosphere such as N2 should be used. • Dip copper pillars in “no-clean flip chip” flux prior to solder attach. Suggest using a high temperature flux. Avoid exposing entire die to flux. • If screen printing flux, use small apertures and minimize volume of flux applied. • Coefficient of thermal expansion matching between the MMIC and the substrate/board is critical for long-term reliability. • Devices must be stored in a dry nitrogen atmosphere. • Suggested reflow will depend on board material and density. See Triquint Application Note for flip-chip soldering process: TBD Typical Reflow Profiles for TriQuint Cu / Sn Pillars Process Sn Reflow Ramp-up Rate 3 ºC/sec Flux Activation Time and Temperature 60 – 120 sec @ 140 – 160 ºC Time above Melting Point (245 C) 60 – 150 sec Max Peak Temperature 300 ºC Time within 5 C of Peak Temperature 10 – 20 sec Ramp-down Rate 4 – 6 ºC/sec Ordering Information Part Package Style TGV2204-FC GaAs MMIC Die GaAs MMIC devices are susceptible to damage from Electrostatic Discharge. Proper precautions should be observed during handling, assembly and test. TriQuint Semiconductor: www. triquint.com (972)994-8465 Fax (972)994-8504 [email protected] November 2009 © Rev D 10