AIMTEC AMEL10

Series AMEL10-AZ
Preliminary
10 Watt | AC-DC Converter
FEATURES:
• I/O Isolation 3000VAC
• Operating Temp: -40oC to +80oC
• Over load, Over Voltage, Short Circuit Protection
• Up to 79% efficiency
•
•
Energy Star compliant
Ultra small package
Models
Single output
Model
AMEL10-3.3SAZ
AMEL10-5SAZ
AMEL10-12SAZ
AMEL10-15SAZ
AMEL10-24SAZ
Input Voltage
(VAC/Hz)
Input
Voltage
(VDC)
90-305/47-440
90-305/47-440
90-305/47-440
90-305/47-440
90-305/47-440
120-430
120-430
120-430
120-430
120-430
Input Specifications
Parameters
Current
Inrush current <2ms (cold start)
Leakage current
External fuse
Input dissipation
Output Specifications
Parameters
Voltage accuracy
Line regulation
Load regulation
Transient recovery time
Transient response deviation
Ripple & Noise*
Max Output
wattage
(W)
9.9
10
10
10
10
Output
Voltage
(V)
3.3
5
12
15
24
Conditions
Parameters
Tested I/O voltage
Isolation Resistance
www.aimtec.com
F 052e R8
3.00
2.00
0.84
0.67
0.42
Typical
115VAC
230VAC
115VAC
230VAC
0.23
0.15
slow blow type
No Load
1
<0.5
Conditions
Typical
0-100% load
25% load step
20MHz bandwidth
*Ripple and Noise are measured at 20MHz bandwidth by using a 0.1µF (M/C) parallel capacitor.
Isolation Specifications
Output
Current max
(A)
Conditions
±2
±1
±2
500
±2
100
Typical
3sec
>1000
Tel: +1 514 620 2722
1 of 3
Maximum
capacitive
load
(µF)
Efficiency
(%)
2200
1000
680
470
470
Maximum
10
20
0.25
Maximum
Rated
3000
74
76
78
79
79
Units
A
A
A
A
mA
A
W
Units
%
%
%
µs
% of Vout
mV p-p
Units
VAC
MΩ
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AMEL10-AZ
Preliminary
General Specifications
Parameters
Conditions
10 Watt | AC-DC Converter
Typical
Maximum
Units
Switching frequency
66
KHz
Over load protection
Auto recovery, Fold back
150
%
Over voltage protection
Zener Diode Clamp
Short circuit protection
Auto recovery
o
Operating temperature
With derating above 50ºC
-40 to +80
C
o
Maximum case temperature
100
C
o
Storage temperature
-45 to +95
C
Temperature coefficient
±0.02
% / oC
Humidity
Non condensing
20 ~ 95
% RH
Case material
Plastic resin + Fiberglass (flammability to UL 94V-0)
Weight
70
g
Dimensions (L x W x H)
2.22 x 1.21 x 0.99 inches
56.48 x 30.86 x 25.10mm
MTBF
> 400 000 hrs (MIL-HDBK -217F, t=+25oC)
NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at
rated output load unless otherwise specified.
Environment Approval
Test
Shock
Vibration
Parameters
Wave form
Acceleration amplitude
Bump duration
Converter operation
Number of bumps
Test mode
Displacement
Acceleration
Converter operation
Conditions
Half sine wave
5gn
30 ms
before and after test, body mounted (on chassis)
18 (3 in each direction for every axis)
Sweep sine
1mm
3g
10-100Hz, speed 0.05Hz/s
Safety Specifications
Parameters
Standards
www.aimtec.com
F 052e R8
Information technology Equipment
EMI - Conducted and radiated emission
Electrostatic Discharge Immunity
RF, Electromagnetic Field Immunity
Electrical Fast Transient/Burst Immunity
Surge Immunity
RF, Conducted Disturbance Immunity
Power frequency Magnetic Field Immunity
Voltage dips, Short Interruptions Immunity
Information Technology Equipment
Information Technology Equipment
Tel: +1 514 620 2722
2 of 3
EN 60950-1:2006+A11:2009
EN55011, class B
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
UL 60950-1:2007
CAN/CSA-C22.2 No.60950-1-07
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AMEL10-AZ
Preliminary
10 Watt | AC-DC Converter
Pin Out Specifications
Pin
Single
1
2
3
4
5
AC Input (N)
AC Input (L)
+V Output
-V Output
No pin
Dimensions
3
Top View 4
5,27
(0.21)
2
5
5.37
(0.21)
1
10.20
(0.40)
1
10.20
(0.40)
45.72
(1.80)
20.40
(0.80)
30.86
(1.21)
5.27
(0.21)
56.46
(2.22)
2
5.37
(0.21)
3
Top View 4
5
25.10
(0.99)
DIV: 10.00 (0.40)
8.00
(0.31)
5Ø 1.0 (Ø 0.04)
Dimensions mm (inch)
Case Tolerance ±0.50 (±0.02)
Pin Diameter 1.0 ± 0.05 (0.04 ± 0.002)
Pin Pitch Tolerance ±0.35 (±0.014)
1.05
(0.04)
NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled
by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the
date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%,
nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components
and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This
product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate
specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com.
www.aimtec.com
F 052e R8
Tel: +1 514 620 2722
3 of 3
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only