6N140A,* HCPL-675X, 83024, HCPL-570X, HCPL-177K, 5962-89810, HCPL-573X, HCPL-673X, 5962-89785, 5962-98002 Hermetically Sealed, Low IF, Wide VCC, High Gain Optocouplers Data Sheet *See matrix for available extensions. Description Features These units are single, dual, and quad channel, hermetically sealed optocouplers. The products are capable of operation and storage over the full military temperature range and can be purchased as either standard product or with full MIL-PRF-38534 Class Level H or K testing or from the appropriate DLA Drawing. All devices are manufactured and tested on a MIL-PRF-38534 certified line and are included in the DLA Qualified Manufacturers List QML-38534 for Hybrid Microcircuits. Dual marked with device part number and DLA drawing number Manufactured and tested on a MIL-PRF-38534 Certified Line QML-38534, Class H and K Five hermetically sealed package configurations Performance guaranteed over full military temperature range: -55°C to +125°C Low input current requirement: 0.5 mA High current transfer ratio: 1500% typical @ IF = 0.5 mA Low output saturation voltage: 0.11 V typical 1500 Vdc withstand test voltage High radiation immunity 6N138/9, HCPL-2730/31 function compatibility Reliability data Each channel contains a GaAsP light emitting diode which is optically coupled to an integrated high gain photon detector. The high gain output stage features an open collector output providing both lower saturation voltage and higher signaling speed than possible with conventional photo-Darlington optocouplers. The shallow depth and small junctions offered by the IC process provides better radiation immunity than conventional photo transistor optocouplers. The supply voltage can be operated as low as 2.0 V without adversely affecting the parametric performance. These devices have a 300% minimum CTR at an input current of only 0.5 mA making them ideal for use in low input current applications such as MOS, CMOS, low power logic interfaces or line receivers. Compatibility with high voltage CMOS logic systems is assured by specifying ICCH and IOH at 18 Volts. Applications Military and aerospace High reliability systems Telephone ring detection Microprocessor system interface Transportation, medical, and life critical systems Isolated input line receiver EIA RS-232-C line receiver Voltage level shifting Isolated input line receiver Isolated output line driver Logic ground isolation Harsh industrial environments Current loop receiver System test equipment isolation Process control input/output isolation The connection of a 0.1 F bypass capacitor between VCC and GND is recommended. CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. Upon special request, the following device selections can be made: CTR minimum of up to 600% at 0.5 mA, and lower output leakage current levels to 100 A. Functional Diagram Multiple Channel Devices Available 1 8 2 7 3 6 4 5 Package styles for these parts are 8 and 16 pin DIP through hole (case outlines P and E respectively), 16 pin DIP flat pack (case outline F), and leadless ceramic chip carrier (case outline 2). Devices may be purchased with a variety of lead bend and plating options. See Selection Guide table for details. Standard Military Drawing (SMD) parts are available for each package and lead style. Because the same electrical die (emitters and detectors) are used for each channel of each device listed in this data sheet, absolute maximum ratings, recommended operating conditions, electrical specifications, and performance characteristics shown in the figures are similar for all parts except as noted. Additionally, the same package assembly processes and materials are used in all devices. These similarities justify the use of a common data base for die related reliability and certain limited radiation test results. Truth Table (Positive Logic) Input Output On (H) L Off (L) H Selection Guide-Package Styles and Lead Configuration Options Package 16 pin DIP 8 pin DIP 8 pin DIP 16 pin Flat Pack 20 Pad LCCC Lead Style Channels Common Channel Wiring Avago Part # & Options Commercial MIL-PRF-38534 Class H MIL-PRF-38534 Class K Standard Lead Finish Solder Dipped* Butt Cut/Gold Plate Gull Wing/Soldered* Crew Cut/Gold Plate Class H SMD Part # Through Hole 4 VCC, GND Through Hole 1 None Through Hole 2 VCC, GND Unformed Leads 4 VCC, GND Surface Mount 2 None 6N140A[1] 6N140A/883B HCPL-177K Gold Plate Option #200 Option #100 Option #300 Option #600 HCPL-5700 HCPL-5701 HCPL-570K Gold Plate Option #200 Option #100 Option #300 Option #600 HCPL-5730 HCPL-5731 HCPL-573K Gold Plate Option #200 Option #100 Option #300 Option #600 HCPL-6750 HCPL-6751 HCPL-675K Gold Plate HCPL-6730 HCPL-6731 HCPL-673K Solder Pads* None 8302401EC 8302401EA 8302401YC 8302401YA 8302401XA 8302401ZC 8302401ZA 59628981001PC 8981001PA 8981001YC 8981001YA 8981001XA Available Available 59628978501PC 8978501PA 8978501YC 8978501YA 8978501ZA Available Available None 8302401FC 5962- 59629800201KEC 9800201KEA 9800201KYC 9800201KYA 9800201KXA 9800201KZC 9800201KZA 59628981002KPC 8981002KPA 8981002KYC 8981002KYA 8981002KXA Available Available 59628978503KPC 8978503KPA 8978503KYC 8978503KYA 8978503KZA Available Available 59629800201KFC Prescript for all below Gold Plate Solder Dipped* Butt Cut/Gold Plate Butt Cut/Soldered* Gull Wing/Soldered* Crew Cut/Gold Plate Crew Cut/Soldered* Class K SMD Part # Prescript for all below Gold Plate Solder Dipped* Butt Cut/Gold Plate Butt Cut/Soldered* Gull Wing/Soldered* Crew Cut/Gold Plate Crew Cut/Soldered* *Solder contains lead. Note: 1. JEDEC registered part. 2 89785022A 59628978504K2A Functional Diagrams 16 pin DIP 8 pin DIP 8 pin DIP 16 pin Flat Pack 20 Pad LCCC Through Hole Through Hole Through Hole Unformed Leads Surface Mount 4 Channels 1 Channel 2 Channels 4 Channels 2 Channels 15 1 16 8 1 8 1 VCC2 16 1 VO2 19 2 15 3 14 4 13 2 7 2 7 2 3 6 3 6 3 4 5 4 5 15 15 20 14 14 2 GND2 VCC1 13 12 10 3 13 4 GND1 VO1 7 5 12 5 12 6 11 6 11 7 10 7 10 8 9 8 9 8 Note: All DIP and flat pack devices have common VCC and ground. LCCC (leadless ceramic chip carrier) package has isolated channels with separate VCC and ground connections. Outline Drawings 16 Pin DIP Through Hole, 4 Channels 20.06 (0.790) 20.83 (0.820) 8.13 (0.320) MAX. 0.89 (0.035) 1.65 (0.065) 4.45 (0.175) MAX. 0.51 (0.020) MIN. 3.81 (0.150) MIN. 2.29 (0.090) 2.79 (0.110) 0.51 (0.020) MAX. 0.20 (0.008) 0.33 (0.013) 7.36 (0.290) 7.87 (0.310) Note: Dimensions in Millimeters (Inches) Leaded Device Marking Avago LOGO Avago P/N DLA SMD* DLA SMD* PIN ONE/ ESD IDENT A QYYWWZ XXXXXX XXXXXXX XXX XXX t 50434 *QUALIFIED PARTS ONLY 3 Leadless Device Marking COMPLIANCE INDICATOR,* DATE CODE, SUFFIX (IF NEEDED) COUNTRY OF MFR. Avago CAGE CODE* Avago LOGO Avago P/N PIN ONE/ ESD IDENT COUNTRY OF MFR. A QYYWWZ XXXXXX t XXXX XXXXXX XXX 50434 COMPLIANCE INDICATOR,* DATE CODE, SUFFIX (IF NEEDED) DLA SMD* DLA SMD* Avago CAGE CODE* Outline Drawings (continued) 16 Pin Flat Pack, 4 Channels 7.24 (0.285) 6.99 (0.275) 2.29 (0.090) MAX. 1.27 (0.050) REF. 11.13 (0.438) 10.72 (0.422) 0.46 (0.018) 0.36 (0.014) 8.13 (0.320) MAX. 2.85 (0.112) MAX. 0.88 (0.0345) MIN. 0.89 (0.035) 0.69 (0.027) 5.23 (0.206) MAX. 0.31 (0.012) 0.23 (0.009) 9.02 (0.355) 8.76 (0.345) Note: Dimensions in Millimeters (Inches) 20 Terminal LCCC Surface Mount, 2 Channels 8 Pin DIP Through Hole, 1 and 2 Channel 8.70 (0.342) 9.10 (0.358) 9.40 (0.370) 9.91 (0.390) 0.76 (0.030) 1.27 (0.050) 4.95 (0.195) 5.21 (0.205) 1.78 (0.070) 2.03 (0.080) 1.02 (0.040) (3 PLCS) 1.14 (0.045) 1.40 (0.055) 8.70 (0.342) 9.10 (0.358) 4.95 (0.195) 5.21 (0.205) TERMINAL 1 IDENTIFIER 2.16 (0.085) 0.64 (0.025) (20 PLCS) 0.51 (0.020) MIN. 3.81 (0.150) MIN. 0.51 (0.020) 1.52 (0.060) 2.03 (0.080) Note: Dimensions in Millimeters (Inches). Solder Thickness 0.127 (0.005) Max. 4 7.16 (0.282) 7.57 (0.298) 4.32 (0.170) MAX. METALIZED CASTILLATIONS (20 PLCS) 1.78 (0.070) 2.03 (0.080) 8.13 (0.320) MAX. 2.29 (0.090) 2.79 (0.110) 0.51 (0.020) MAX. Note: Dimensions in Millimeters (Inches). 0.20 (0.008) 0.33 (0.013) 7.36 (0.290) 7.87 (0.310) Hermetic Optocoupler Options Option Description 100 Surface mountable hermetic optocoupler with leads trimmed for butt joint assembly. This option is available on commercial and hi-rel product in 8 and 16 pin DIP (see drawings below for details). 4.32 (0.170) MAX. 0.51 (0.020) MIN. 1.14 (0.045) 1.40 (0.055) 0.51 (0.020) MAX. 2.29 (0.090) 2.79 (0.110) 4.32 (0.170) MAX. 0.51 (0.020) MIN. 1.14 (0.045) 1.40 (0.055) 0.20 (0.008) 0.33 (0.013) 0.51 (0.020) MAX. 2.29 (0.090) 2.79 (0.110) 7.36 (0.290) 7.87 (0.310) Note: Dimensions in Millimeters (Inches). 200 Lead finish is solder dipped rather than gold plated. This option is available on commercial and hi-rel product in 8 and 16 pin DIP. DLA Drawing part numbers contain provisions for lead finish. All leadless chip carrier devices are delivered with solder dipped terminals as a standard feature. 300 Surface mountable hermetic optocoupler with leads cut and bent for gull wing assembly. This option is available on commercial and hi-rel product in 8 and 16 pin DIP (see drawings below for details). This option has solder dipped leads. 4.57 (0.180) MAX. 0.51 (0.020) MIN. 1.40 (0.055) 1.65 (0.065) 0.51 (0.020) MAX. 2.29 (0.090) 2.79 (0.110) 4.57 (0.180) MAX. 0.51 (0.020) MIN. 1.40 (0.055) 1.65 (0.065) 4.57 (0.180) MAX. 0.20 (0.008) 0.33 (0.013) 5° MAX. 9.65 (0.380) 9.91 (0.390) 0.51 (0.020) MAX. 2.29 (0.090) 2.79 (0.110) 1.07 (0.042) 1.32 (0.052) Note: Dimensions in Millimeters (Inches). 600 Surface mountable hermetic optocoupler with leads trimmed for butt joint assembly. This option is available on commercial and hi-rel product in 8 and 16 pin DIP (see drawings below for details). Contact factory for the availability of this option on DLA part types. 3.81 (0.150) MIN. MAX. 0.51 (0.020) MIN. 0.20 (0.008) 0.33 (0.013) 2.29 (0.090) 2.79 (0.110) 1.14 (0.045) 1.25 (0.049) Note: Dimensions in Millimeters (Inches). Solder contains lead. 5 3.81 (0.150) MAX. 7.36 (0.290) 7.87 (0.310) 0.51 (0.020) MIN. 2.29 (0.090) 2.79 (0.110) 1.02 (0.040) TYP. Absolute Maximum Ratings Parameter Symbol Min. Max. Units Storage Temperature TS -65 +150 °C Operating Temperature TA -55 +125 °C Case Temperature TC +170 °C Junction Temperature TJ +175 °C 260 for 10 sec °C 40 mA Lead Solder Temperature Notes Output Current (each channel) IO Output Voltage (each channel) VO -0.5 20 V 1 Supply Voltage VCC -0.5 20 V 1 Output Power Dissipation (each channel) 50 mW 2 Peak Input Current (each channel, <1 ms duration) 20 mA Average Input Current (each channel) IF 10 mA Reverse Input Voltage (each channel) VR 5 V Package Power Dissipation (each channel) PD 200 mW 3 8 Pin Ceramic DIP Single Channel Schematic ANODE 2 IF VCC 8 ICC + VF CATHODE – IO 6 3 5 VO GND ESD Classification (MIL-STD-883, Method 3015) HCPL-5700/01/0K and 6730/31/3K ( ), Class 2 6N140A, 6N140A/883B, HCPL-177K, HCPL-6750/51/5K and HCPL-5730/31/3K (Dot), Class 3 Recommended Operating Conditions Parameter Symbol Input Voltage, Low Level (Each Channel) VF(OFF) Input Current, High Level (Each Channel) IF(ON) Supply Voltage Output Voltage 6 Min. Max. Units 0.8 V 0.5 5 mA VCC 2.0 18 V VO 2.0 18 V Electrical Characteristics, TA = -55°C to +125°C, unless otherwise specified Min. Typ.** 1, 2, 3 300 1500 IF = 1.6 mA, VO = 0.4 V, VCC = 4.5 V 300 1000 IF =5 mA, VO = 0.4 V, VCC = 4.5 V 200 500 Parameter Symbol Test Conditions Current Transfer Ratio CTR* IF = 0.5 mA, VO = 0.4 V, VCC = 4.5 V Logic Low Output Voltage VOL Logic High Supply Current IF = 0.5 mA, IOL = 1.5 mA, VCC = 4.5 V 1, 2, 3 3 4, 5 V 2 4 0.4 4, 16 IF =5 mA, IOL = 10 mA, VCC = 4.5 V 0.16 0.4 4 0.001 250 A 4 250 A 4, 6 1.0 2 mA 15 Dual Channel IF1 =IF2 = 1.6 mA, VCC = 18 V 1.0 4 Quad Channel IF1 = IF2 =IF3 =IF4 =1.6 mA, VCC = 18 V 1.7 4 Single ICCH* Channel and LCCC IF =0 mA, VCC = 18 V 0.001 20 Dual Channel IF1 =IF2 = 0 mA, VCC = 18 V 40 Quad Channel IF1 = IF2 =IF3 =IF4 =0 mA, VCC = 18 V 40 IF = 1.6 mA 1, 2, 3 1 1.0 1.7 1.7 3 1.8 1, 2, 3 Quad Channel 1, 2 1.0 3 IR = 10 A 1, 2, 3 Input-Output II-O* Insulation Leakage Current ≤65% Relative Humidity TA =25°C, t = 5 s, VI-O = 1500 VDC 1 Capacitance Between Input-Output f= 1 MHz, TA =25°C 4 * For JEDEC registered parts. ** All typical values are at VCC = 5 V, TA = 25°C. 1.4 2 LCCC CI-O % 0.13 1, 2, 3 BVR* Note IF = 1.6 mA, IOL = 4.8 mA, VCC = 4.5 V IF =1.6 mA, VCC = 18 V Input Reverse Breakdown Voltage Fig. 0.4 Single ICCL* Channel and LCCC VF* Units 0.11 1, 2, 3 Single Input Forward and Dual Voltage Channel 7 Max. IF =2 A, VO = 18 V, VCC = 18 V Logic High Output IOH* Current IOHX Logic Low Supply Current Limits Group A[13] Subgroup 1.4 1.8 1.4 1.7 4 A V 15 1 4 1.8 5 V 4 1.0 A 7, 12 4 pF 4, 8 14, 17 Electrical Characteristics (cont), TA = -55°C to +125°C, unless otherwise specified Parameter Symbol Propagation Delay tPHL* Time to Logic Low at Output tPHL tPHL* Propagation Delay tPLH* Time to Logic High at Output tPLH tPLH* Group A[13] Subgroup Test Conditions Limits Min. Typ.** Max. Units Fig. Note s 5, 6, 7, 8 4 IF = 0.5 mA, RL = 4.7 k, VCC =5 V 9, 10, 11 30 100 IF = 1.6 mA, RL = 1.5 k, VCC =5 V 9, 10, 11 5 30 4, 16 IF =5 mA, RL = 680 , VCC =5 V 9 2 5 4, 17 10, 11 10 9, 10, 11 10 4, 16 s IF = 0.5 mA, RL = 4.7 k, VCC =5 V 9, 10, 11 17 60 IF = 1.6 mA, RL = 1.5 k, VCC =5 V 9, 10, 11 14 50 4, 16 IF =5 mA, RL = 680 , VCC =5 V 9 8 20 4, 17 10, 11 30 9, 10, 11 30 5, 6, 7, 8 4 4, 16 Common Mode Transient Immunity at Low Output Level |CML| VCC =5 V, IF = 1.6 mA RL =1.5 k |VCM|= 25 VP-P[17] |VCM|= 50 VP-P[16] 9, 10, 11 500 1000 V/s 9 4, 10 11, 14 Common Mode Transient Immunity at High Output Level |CMH| VCC =5 V, IF =0 mA RL =1.5 k |VCM|= 25 VP-P[17] |VCM|= 50 VP-P[16] 9, 10, 11 500 1000 V/s 9 4, 10 11, 14 * For JEDEC registered parts. ** All typical values are at VCC = 5 V, TA = 25°C. Typical Characteristics, TA = 25°C, VCC = 5 V Parameter Sym. Typ. Units Test Conditions Note Input Capacitance CIN 60 pF VF =0 V, f = 1 MHz 4 Input Diode Temperature Coefficient VF/TA -1.8 mV/°C IF = 1.6 mA 4 Resistance (Input-Output) RI-O 1012 VI-O = 500 V 4, 8 Capacitance (Input-Output) CI-O 2.0 pF f = 1 MHz 4, 8 Input-Input Leakage Current II-I 0.5 nA Relative Humidity = ≤65%, VI-I = 500 V, t = 5 s 9 Resistance (Input-Input) RI-I 1012 VI-I = 500 V 9 Capacitance (Input-Input) CI-I 1.0 pF f = 1 MHz 9 Dual and Quad Channel Product Only 8 Notes: 1. GND Pin should be the most negative voltage at the detector side. Keeping VCC as low as possible, but greater than 2.0 V, will provide lowest total IOH over temperature. 2. Output power is collector output power plus total supply power for the single channel device. For the dual channel device, output power is collector output power plus one half the total supply power. For the quad channel device, output power is collector output power plus one fourth of total supply power. Derate at 1.66 mW/°C above 110°C. 3. Derate IF at 0.33 mA/°C above 110°C. 4. Each channel. 5. CURRENT TRANSFER RATIO is defined as the ratio of output collector current, IO, to the forward LED input current, IF, times 100%. 6. IOHX is the leakage current resulting from channel to channel optical crosstalk. IF = 2 μA for channel under test. For all other channels, IF = 10 mA. 7. All devices are considered two-terminal devices; measured between all input leads or terminals shorted together and all output leads or terminals shorted together. 8. Measured between each input pair shorted together and all output connections for that channel shorted together. 9. Measured between adjacent input pairs shorted together for each multi-channel device. 10. CML is the maximum rate of rise of the common mode voltage that can be sustained with the output voltage in the logic low state (VO < 0.8 V). CMH is the maximum rate of fall of the common mode voltage that can be sustained with the output voltage in the logic high state (VO > 2.0 V). 9 11. In applications where dV/dt may exceed 50,000 V/s (such as a static discharge) a series resistor, RCC, should be included to protect the detector ICs from destructively high surge currents. The recommended value is: 1 (V) RCC = ————— k 0.15 IF (mA) for single channel; 1 (V) RCC = ————— k 0.3 IF (mA) for dual channel; 1 (V) RCC = ————— k 0.6 IF (mA) for quad channel. 12. This is a momentary withstand test, not an operating condition. 13. Standard parts receive 100% testing at 25°C (Subgroups 1 and 9). SMD and 883B parts receive 100% testing at 25,125, and -55°C (Subgroups 1 and 9, 2 and 10, 3 and 11, respectively). 14. Parameters tested as part of device initial characterization and after design and process changes. Parameters guaranteed to limits specified for all lots not specifically tested. 15. The HCPL-6730, HCPL-6731, and HCPL-673K dual channel parts function as two independent single channel units. Use the single channel parameter limits. 16. Not required for 6N140A, 6N140A/883B, HCPL-177K, HCPL6750/51/5K, 8302401, and 5962-9800201 types. 17. Required for 6N140A, 6N140A/883B, HCPL-177K, HCPL-6750/51/5K, 8302401, and 5962-9800201 types. Figure 1. Input Diode Forward Current vs. Forward Voltage. Figure 2. Normalized DC Transfer Characteristics. Figure 3. Normalized Current Transfer Ratio vs. Input Diode Forward Current. Figure 4. Normalized Supply Current vs. Input Diode Forward Current. Figure 5. Propagation Delay to Logic Low vs. Input Pulse Period. Figure 6. Propagation Delay vs. Temperature. Figure 7. Propagation Delay vs. Input Diode Forward Current. 10 PULSE GEN. ZO = 50 tr, tf = 50 ns f = 100 Hz tPULSE = 0.5ms RCC * IF IF MONITOR Rm 1 8 2 7 3 6 4 5 56 1.0 F IF +5 V RL RCC * B 1 8 2 7 3 6 A VO CL** VFF 4 VCC R1 R2 1 8 2 7 3 6 4 5 R2 MAY BE OMITTED IF ADDITIONAL FANOUT IS NOT USED. Figure 10. Recommended Drive Circuitry Using TTL Open-Collector Logic. 11 VCM – * SEE NOTE 11 Figure 8. Switching Test Circuit (f, tP not JEDEC registered). 2.4 VF IF VCC VF IF R2 R1 ≤ IF + ILEAK +5 V RL PULSE GEN. * SEE NOTE 11 ** CL INCLUDES PROBE AND STRAY WIRING CAPACITANCE. R2 ≥ 1.0 F 5 + ILEAK 56 Figure 9. Test Circuit for Transient Immunity and Typical Waveforms. VO MIL-PRF-38534 Class H, Class K, and DLA SMD Test Program Avago’s Hi-Rel Optocouplers are in compliance with MILPRF-38534 Class H and K. Class H and Class K devices are also in compliance with DLA drawings 83024, 5962-89785, 5962-89810, and 5962-98002. Testing consists of 100% screening and quality conformance inspection to MIL-PRF-38534. VCC + 18 V (EACH INPUT) + VIN – 1 8 2 7 3 6 4 5 VOC 0.01 F (EACH OUTPUT) CONDITIONS: IF = 10 mA IO = 40 mA TA = +125°C * ALL CHANNELS TESTED SIMULTANEOUSLY. Figure 11. Operating Circuit for Burn-In and Steady State Life Tests. For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2012 Avago Technologies. All rights reserved. Obsoletes 5968-9400E AV02-1766EN - October 2, 2012