Data Sheet 1.5MHz, 800mA, STEP DOWN DC-DC CONVERTER General Description Features The AUR9703 is a high efficiency step-down DC-DC voltage converter. The chip operation is optimized using constant frequency, peak-current mode architecture with built-in synchronous power MOSFET switchers and internal compensators to reduce external part counts. It is automatically switching between the normal PWM mode and LDO mode to offer improved system power efficiency covering a wide range of loading conditions. • • • • • • • • • • • • The oscillator and timing capacitors are all built-in providing an internal switching frequency of 1.5MHz that allows the use of small surface mount inductors and capacitors for portable product implementations. Additional features included Soft Start (SS), Under Voltage Lock Out (UVLO), and Thermal Shutdown Detection (TSD) to provide reliable product applications. AUR9703 High Efficiency Buck Power Converter Low Quiescent Current Output Current: 800mA Adjustable Output Voltage from 1V to 3.3V Wide Operating Voltage Range: 2.5V to 5.5V Built-in Power Switches for Synchronous Rectification with High Efficiency Feedback Voltage: 600mV 1.5MHz Constant Frequency Operation Automatic PWM/LDO Mode Switching Control Thermal Shutdown Protection Low Drop-out Operation at 100% Duty Cycle No Schottky Diode Required Applications • • • • The device is available in adjustable output voltage versions ranging from 1V to 3.3V, and is able to deliver up to 800mA. Mobile Phone, Digital Camera and MP3 Player Headset, Radio and Other Hand-held Instrument Post DC-DC Voltage Regulation PDA and Notebook Computer The AUR9703 is available in TSOT-23-5 package. TSOT-23-5 Figure 1. Package Type of AUR9703 Nov. 2011 Rev. 1 .0 BCD Semiconductor Manufacturing Limited 1 Data Sheet 1.5MHz, 800mA, STEP DOWN DC-DC CONVERTER AUR9703 Pin Configuration H Package (TSOT-23-5) 5 1 2 3 4 Figure 2. Pin Configuration of AUR9703 (Top View) Pin Description Pin Number Pin Name 1 EN 2 GND 3 LX Connect to inductor 4 VIN Power supply input 5 FB Feedback voltage from the output Nov. 2011 Function Enable signal input, active high This pin is the GND reference for the NMOS power stage. It must be connected to the system ground Rev. 1 .0 BCD Semiconductor Manufacturing Limited 2 Data Sheet 1.5MHz, 800mA, STEP DOWN DC-DC CONVERTER AUR9703 Functional Block Diagram Figure 3. Functional Block Diagram of AUR9703 Ordering Information AUR9703 A Package H: TSOT-23-5 G: Green Circuit Type A: Adjustable Output 5 Temperature Package Range TSOT-23-5 -40 to 80°C Part Number AUR9703AGH Marking ID 9703AG Packing Type Tape & Reel BCD Semiconductor's Pb-free products, as designated with "G" in the part number, are RoHS compliant and green. Nov. 2011 Rev. 1 .0 BCD Semiconductor Manufacturing Limited 3 Data Sheet 1.5MHz, 800mA, STEP DOWN DC-DC CONVERTER AUR9703 Absolute Maximum Ratings (Note 1) Parameter Symbol Value Unit Supply Input Voltage VIN 0 to 6.0 V Enable Input Voltage VEN -0.3 to VIN+0.3 V Output Voltage VOUT -0.3 to VIN+0.3 V Power Dissipation (On PCB, TA=25°C) PD 0.85 W Thermal Resistance (Junction to Ambient, Simulation) θJA 118.31 °C/W Thermal Resistance (Junction to Case, Simulation) θJC 113.67 °C/W Operating Junction Temperature TJ 160 °C Operating Temperature TOP -40 to 85 °C Storage Temperature TSTG -55 to 150 °C ESD (Human Body Model) VHBM 2000 V ESD (Machine Model) VMM 200 V Note 1: Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “Recommended Operating Conditions” is not implied. Exposure to “Absolute Maximum Ratings” for extended periods may affect device reliability. Recommended Operating Conditions Parameter Symbol Min Max Unit Supply Input Voltage VIN 2.5 5.5 V Junction Temperature Range TJ -20 125 °C Ambient Temperature Range TA -40 80 °C Nov. 2011 Rev. 1 .0 BCD Semiconductor Manufacturing Limited 4 Data Sheet 1.5MHz, 800mA, STEP DOWN DC-DC CONVERTER AUR9703 Electrical Characteristics VIN=5V, VOUT=3.3V, VFB=0.6V, L=2.2µH, CIN=4.7µF, COUT=10µF, TA=25°C, IMAX=800mA. Unless otherwise specified. Parameter Symbol Conditions Min Typ Max Unit Input Voltage Range VIN Shutdown Current Regulated1Feedback Voltage Regulated Output Voltage Accuracy Peak Inductor Current IOFF VEN=0 VFB For Adjustable Output Voltage Oscillator Frequency 2.5 ∆VOUT/VOUT VIN=2.5V to 5.5V, IOUT=0 to 800mA IPK VIN=5V, VFB=0.5V fOSC VIN=5V 0.585 5.5 V 0.1 1 µA 0.6 0.615 V 3 % -3 1.2 1.2 1.5 A 1.8 MHz PMOSFET RON RON(P) VIN=5V, IOUT=200mA 0.25 Ω NMOSFET RON RON(N) VIN=5V, IOUT=200mA 0.27 Ω Quiescent Current IQ IOUT=0A, VFB= 0.7V 100 µA LX Leakage Current ILX VEN=0V, VIN=5V Feedback Current IFB Soft Start Time tSS 200 EN Leakage Current IEN 0.01 EN High-level Input Voltage VEN_H VIN=2.5V to 5.5V EN Low-Level Input Voltage VEN_L VIN=2.5V to 5.5V Under Voltage Lock Out VUVLO VLX=0V Hysteresis Thermal Shutdown Nov. 2011 TSD Rev. 1 .0 or 5V, 0.1 1 µA 30 nA µs 0.1 1.5 µA V 0.6 V 1.8 V 0.1 V 160 °C BCD Semiconductor Manufacturing Limited 5 Data Sheet 1.5MHz, 800mA, STEP DOWN DC-DC CONVERTER AUR9703 Typical Performance Characteristics 90 80 80 70 70 Efficiency (%) 100 90 Efficiency (%) 100 60 50 40 VIN=2.5V VIN=3.3V 30 VIN=4.2V VIN=5.0V 20 50 VIN=2.5V 40 VIN=3.3V 30 VIN=4.2V VIN=5.0V 20 VIN=5.5V 10 60 VIN=5.5V 10 VOUT=1.0V 0 VOUT=1.2V 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.0 0.1 0.2 Output Current (A) 0.4 0.5 0.6 0.7 0.8 Figure 5. Efficiency vs. Output Current (VOUT=1.2V) 100 100 90 90 80 80 70 70 Efficiency (%) Efficiency (%) Figure 4. Efficiency vs. Output Current (VOUT=1.0V) 60 50 40 VIN = 2.5V 30 VIN = 4.2V VIN = 3.3V VIN = 5.0V 20 60 50 40 VIN = 3.3V 30 VIN = 4.2V VIN = 5.0V 20 VIN = 5.5V VOUT=1.8V 10 0.3 Output Current (A) VIN = 5.5V 10 0 VOUT=2.5V 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.0 Figure 6. Efficiency vs. Output Current (VOUT=1.8V) Nov. 2011 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 Output Current (A) Output Current (A) Figure 7. Efficiency vs. Output Current (VOUT=2.5V) Rev. 1 .0 BCD Semiconductor Manufacturing Limited 6 Data Sheet 1.5MHz, 800mA, STEP DOWN DC-DC CONVERTER AUR9703 Typical Performance Characteristics (Continued) 100 1.03 90 80 VIN=3.3V VIN=4.2V Output Voltage (V) 70 Efficiency (%) VIN=2.5V 1.02 60 50 40 30 VIN = 4.2V VIN = 5.0V 20 VIN = 5.5V VIN=5.0V 1.01 VIN=5.5V 1.00 0.99 0.98 VOUT=3.3V 10 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.97 0.0 0.8 0.1 0.2 Output Current (A) Figure 8. Efficiency vs. Output Current (VOUT=3.3V) 1.24 VIN=3.3V VIN=4.2V VIN=5.0V Output Voltage (V) Output Voltage (V) 1.22 VIN=5.5V 1.21 1.20 1.19 1.18 1.17 0.5 0.6 0.7 0.8 Figure 9. Load Regulation (VOUT=1.0±0.03V) 1.84 VIN=2.5V 1.83 VIN=3.3V 1.82 VIN=5.0V VIN=4.2V VIN=5.5V 1.81 1.80 1.79 1.78 1.77 1.76 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 Output Current (A) 1.75 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 Output Current (A) Figure 10. Load Regulation (VOUT=1.2±0.03V) Nov. 2011 0.4 1.85 VIN=2.5V 1.23 1.16 0.0 0.3 Output Current (A) Figure 11. Load Regulation (VOUT=1.8±0.03V) Rev. 1 .0 BCD Semiconductor Manufacturing Limited 7 Data Sheet 1.5MHz, 800mA, STEP DOWN DC-DC CONVERTER AUR9703 Typical Performance Characteristics (Continued) 3.40 2.56 VIN=3.3V VIN=5.0V 3.36 VIN=5.5V 3.34 Output Voltage (V) Output Voltage (V) 3.38 VIN=4.2V 2.54 2.52 2.50 2.48 2.46 VIN=4.2V VIN=5.0V VIN=5.5V 3.32 3.30 3.28 3.26 3.24 3.22 2.44 0.0 3.20 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.0 0.8 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 Output Current (A) Output Current (A) Figure 12. Load Regulation (VOUT=2.5±0.03V) Figure 13. Load Regulation (VOUT=3.3±0.03V) 1.03 1.24 1.23 1.02 Output Voltage (V) Output Voltage (V) 1.22 1.01 1.00 0.99 IOUT=0A 0.98 IOUT=800mA 1.21 1.20 1.19 1.18 IOUT=0A IOUT=800mA 1.17 0.97 1.16 2.5 3.0 3.5 4.0 4.5 5.0 5.5 2.5 Figure 14. Line Regulation (VOUT=1.0±0.03V) Nov. 2011 3.0 3.5 4.0 4.5 5.0 5.5 Input Voltage (V) Input Voltage (V) Figure 15. Line Regulation (VOUT=1.2±0.03V) Rev. 1 .0 BCD Semiconductor Manufacturing Limited 8 Data Sheet 1.5MHz, 800mA, STEP DOWN DC-DC CONVERTER AUR9703 Typical Performance Characteristics (Continued) 1.85 2.56 1.84 IOUT = 0A IOUT = 0A 2.54 IOUT = 800mA 1.82 Output Voltage (V) Output Voltage (V) 1.83 1.81 1.80 1.79 1.78 1.77 IOUT = 800mA 2.52 2.50 2.48 2.46 1.76 1.75 2.5 3.0 3.5 4.0 4.5 5.0 2.44 2.5 5.5 3.0 3.5 4.0 4.5 5.0 5.5 Input Voltage (V) Input Voltage (V) Figure 16. Line Regulation (VOUT=1.8±0.03V) Figure 17. Line Regulation (VOUT=2.5±0.03V) 1.2 3.40 3.38 Output Voltage (V) EN Threshold Voltage (V) IOUT = 0A 3.36 IOUT = 800mA 3.34 3.32 3.30 3.28 3.26 3.24 3.22 3.20 1.0 0.9 High Level 0.8 Low Level 0.7 VOUT=1.2V IOUT=200mA 3.5 4.0 4.5 5.0 5.5 Input Voltage (V) 0.6 2.5 3.0 3.5 4.0 4.5 5.0 5.5 Input Voltage (V) Figure 18. Line Regulation (VOUT=3.3±0.03V) Nov. 2011 1.1 Figure 19.EN Threshold Voltage vs. Input Voltage Rev. 1 .0 BCD Semiconductor Manufacturing Limited 9 Data Sheet 1.5MHz, 800mA, STEP DOWN DC-DC CONVERTER AUR9703 Typical Performance Characteristics (Continued) 1.8 50 VIN=5.0V 45 1.6 o Temperature ( C) Frequency (MHz) 1.7 1.5 1.4 VOUT=1.2V 1.3 VOUT=1.0V VOUT=3.3V 40 35 30 IOUT=400mA 1.2 2.5 25 3.0 3.5 4.0 4.5 5.0 5.5 0.0 Input Voltage (V) 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 Output Current (A) Figure 20.Frequency vs. Input Voltage Figure 21.Temperature vs. Output Current 3.0 2.8 Current Limit (A) 2.6 2.4 2.2 2.0 1.8 1.6 1.4 VOUT=1.2V 1.2 1.0 3.0 3.5 4.0 4.5 5.0 5.5 Input Voltage (V) Figure 22. Current Limit vs. Input Voltage Nov. 2011 Figure 23. Start Up through EN (VIN=5V, VEN= 0 to 5V, VOUT=3.3V, IOUT=800mA) Rev. 1 .0 BCD Semiconductor Manufacturing Limited 10 Data Sheet 1.5MHz, 800mA, STEP DOWN DC-DC CONVERTER AUR9703 Typical Performance Characteristics (Continued) Figure 24. Shut Down through EN (VIN=5V, VEN=5V to 0V, VOUT=3.3V, IOUT=800mA) Figure 25. Start Up through VIN (VIN=0 to 5V, VOUT=3.3V, IOUT=800mA) Figure 26. Shut Down through VIN (VIN=5.0 to 0V, VOUT=3.3V, IOUT=800mA) Nov. 2011 Figure 27. Short Circuit Protection (VIN=5.0V, VOUT =3.3V, IOUT=800mA) Rev. 1 .0 BCD Semiconductor Manufacturing Limited 11 Data Sheet 1.5MHz, 800mA, STEP DOWN DC-DC CONVERTER AUR9703 Typical Performance Characteristics (Continued) Figure 28. Short Circuit Recovery (VIN=5.0V, VOUT=3.3V, IOUT=800mA) Figure 29. Load Transition ( VIN=5.0V, VOUT=1.0V, IOUT=50mA to 400mA) Figure 30. Load Transition (VIN=5.0V, VOUT=3.3V, IOUT=50mA to 400mA) Nov. 2011 Figure 31. Load Transition (VIN=5.0V, VOUT=1.0V, IOUT=50mA to 800mA) Rev. 1 .0 BCD Semiconductor Manufacturing Limited 12 Data Sheet 1.5MHz, 800mA, STEP DOWN DC-DC CONVERTER AUR9703 Typical Performance Characteristics (Continued) Figure 32. Load Transition (VIN=5.0V, VOUT=3.3V, IOUT=50mA to 800mA) Figure 33. Output Ripple Voltage (VIN=5.0V, VOUT=1.0V, IOUT=10mA) Figure 34. Output Ripple Voltage (VIN=5V, VOUT=3.3V, IOUT=10mA) Figure 35. Output Ripple Voltage (VIN=5V, VOUT=1.0V, IOUT=400mA) Nov. 2011 Rev. 1 .0 BCD Semiconductor Manufacturing Limited 13 Data Sheet 1.5MHz, 800mA, STEP DOWN DC-DC CONVERTER AUR9703 Typical Performance Characteristics (Continued) Figure 36. Output Ripple Voltage (VIN=5V, VOUT=3.3V, IOUT=400mA) Figure 37. Output Ripple Voltage (VIN=5V, VOUT=1.0V, IOUT=800mA) Figure 38. Output Ripple Voltage (VIN=5V, VOUT=3.3V, IOUT=800mA) Nov. 2011 Rev. 1 .0 BCD Semiconductor Manufacturing Limited 14 Data Sheet 1.5MHz, 800mA, STEP DOWN DC-DC CONVERTER AUR9703 Application Information qw The basic AUR9703 application circuit is shown in Figure 41, external components selection is determined by the load current and is critical with the selection of inductor and capacitor values. deviations do not much relieve. The selection of COUT is determined by the Effective Series Resistance (ESR) that is required to minimize output voltage ripple and load step transients, as well as the amount of bulk capacitor that is necessary to ensure that the control loop is stable. Loop stability can be also checked by viewing the load step transient response as described in the following section. The output ripple, △VOUT, is determined by: 1. Inductor Selection For most applications, the value of inductor is chosen based on the required ripple current with the range of 2.2µH to 4.7µH. ∆VOUT ≤ ∆I L [ ESR + V 1 ∆I L = VOUT (1 − OUT ) f ×L VIN The output ripple is the highest at the maximum input voltage since △IL increases with input voltage. The largest ripple current occurs at the highest input voltage. Having a small ripple current reduces the ESR loss in the output capacitor and improves the efficiency. The highest efficiency is realized at low operating frequency with small ripple current. However, larger value inductors will be required. A reasonable starting point for ripple current setting is △IL=40%IMAX . For a maximum ripple current stays below a specified value, the inductor should be chosen according to the following equation: L =[ 3. Load Transient A switching regulator typically takes several cycles to respond to the load current step. When a load step occurs, VOUT immediately shifts by an amount equal to △ILOAD×ESR, where ESR is the effective series resistance of output capacitor. △ILOAD also begins to charge or discharge COUT generating a feedback error signal used by the regulator to return VOUT to its steady-state value. During the recovery time, VOUT can be monitored for overshoot or ringing that would indicate a stability problem. VOUT VOUT ][1 − ] f × ∆I L ( MAX ) VIN ( MAX ) 4. Output Voltage Setting The DC current rating of the inductor should be at least equal to the maximum output current plus half the highest ripple current to prevent inductor core saturation. For better efficiency, a lower DC-resistance inductor should be selected. The output voltage of AUR9703 can be adjusted by a resistive divider according to the following formula: VOUT = VREF × (1 + 2. Capacitor Selection I RMS = I OMAX VOUT R1 FB 1 2 AUR9703 R2 GND It indicates a maximum value at VIN=2VOUT, where IRMS=IOUT/2. This simple worse-case condition is commonly used for design because even significant Nov. 2011 R1 R ) = 0.6V × (1 + 1 ) R2 R2 The resistive divider senses the fraction of the output voltage as shown in Figure 39. The input capacitance, CIN, is needed to filter the trapezoidal current at the source of the top MOSFET. To prevent large ripple voltage, a low ESR input capacitor sized for the maximum RMS current must be used. The maximum RMS capacitor current is given by: [V (V − VOUT )] × OUT IN VIN 1 ] 8 × f × COUT Figure 39. Setting the Output Voltage Rev. 1 .0 BCD Semiconductor Manufacturing Limited 15 Data Sheet 1.5MHz, 800mA, STEP DOWN DC-DC CONVERTER AUR9703 Application Information (Continued) 5. Efficiency Considerations RDS(ON) resistance and the duty cycle (D): The efficiency of switching regulator is equal to the output power divided by the input power times 100%. It is usually useful to analyze the individual losses to determine what is limiting efficiency and which change could produce the largest improvement. Efficiency can be expressed as: RSW = RDS (ON )P × D + RDS (ON ) N × (1 − D ) Therefore, to obtain the I2R losses, simply add RSW to RL and multiply the result by the square of the average output current. Other losses including CIN and COUT ESR dissipative losses and inductor core losses generally account for less than 2 % of total additional loss. Efficiency=100%-L1-L2-….. Where L1, L2, etc. are the individual losses as a percentage of input power. 6. Thermal Characteristics In most applications, the part does not dissipate much heat due to its high efficiency. However, in some conditions when the part is operating in high ambient temperature with high RDS(ON) resistance and high duty cycles, such as in LDO mode, the heat dissipated may exceed the maximum junction temperature. To avoid the part from exceeding maximum junction temperature, the user should do some thermal analysis. The maximum power dissipation depends on the layout of PCB, the thermal resistance of IC package, the rate of surrounding airflow and the temperature difference between junction and ambient. Although all dissipative elements in the regulator produce losses, two major sources usually account for most of the power losses: VIN quiescent current and I2R losses. The VIN quiescent current loss dominates the efficiency loss at very light load currents and the I2R loss dominates the efficiency loss at medium to heavy load currents. 5.1 The VIN quiescent current loss comprises two parts: the DC bias current as given in the electrical characteristics and the internal MOSFET switch gate charge currents. The gate charge current results from switching the gate capacitance of the internal power MOSFET switches. Each cycle the gate is switched from high to low, then to high again, and the packet of charge, dQ moves from VIN to ground. The resulting dQ/dt is the current out of VIN that is typically larger than the internal DC bias current. In continuous mode, 7. PCB Layout Considerations When laying out the printed circuit board, the following checklist should be used to optimize the performance of AUR9703. I GATE = f × (Q P + Q N ) 1) The power traces, including the GND trace, the LX trace and the VIN trace should be kept direct, short and wide. 2) Place the input capacitor as close as possible to the VIN and GND pins. 3) The FB pin should be connected directly to the feedback resistor divider. 4) Keep the switching node, LX, away from the sensitive FB pin and the node should be kept small area. Where QP and QN are the gate charge of power PMOSFET and NMOSFET switches. Both the DC bias current and gate charge losses are proportional to the VIN and this effect will be more serious at higher input voltages. 5.2 I2R losses are calculated from internal switch resistance, RSW and external inductor resistance RL. In continuous mode, the average output current flowing through the inductor is chopped between power PMOSFET switch and NMOSFET switch. Then, the series resistance looking into the LX pin is a function of both PMOSFET RDS(ON) and NMOSFET Nov. 2011 Rev. 1 .0 BCD Semiconductor Manufacturing Limited 16 Data Sheet 1.5MHz, 800mA, STEP DOWN DC-DC CONVERTER AUR9703 Application Information (Continued) Figure 40. Layout Example of AUR9703 Nov. 2011 Rev. 1 .0 BCD Semiconductor Manufacturing Limited 17 Data Sheet 1.5MHz, 800mA, STEP DOWN DC-DC CONVERTER AUR9703 Typical Application R2 IR2 1 FB EN R1 5 C1 2 GND L 2.2µH VOUT VIN=2.5V to 5.5V 3 LX VIN 4 CIN 4.7 F COUT 10 F Note 2: VOUT 1 = VREF × (1 + R1 ). R2 When R2=300kΩ to 60kΩ, the IR2=2µA to 10µA, and R1×C1 should be in the range between 3×10-6 and 6×10-6 for component selection. Figure 41. Typical Application Circuit of AUR9703 Table 1. Component Guide Nov. 2011 VOUT(V) R1(kΩ) R2(kΩ) C1(pF) L1(µH) 1.0 68 100 82 2.2 1.2 100 100 56 2.2 1.8 200 100 30 2.2 2.5 320 100 18 2.2 3.3 453 100 13 2.2 Rev. 1 .0 BCD Semiconductor Manufacturing Limited 18 Data Sheet 1.5MHz, 800mA, STEP DOWN DC-DC CONVERTER AUR9703 Mechanical Dimensions 5° Unit: mm(inch) GAUGE PLANE TSOT-23-5 4X7 ° Nov. 2011 Rev. 1 .0 BCD Semiconductor Manufacturing Limited 19 BCD Semiconductor Manufacturing Limited http://www.bcdsemi.com IMPORTANT NOTICE IMPORTANT NOTICE BCD Semiconductor BCD Semiconductor Manufacturing Manufacturing Limited Limited reserves reserves the the right right to to make make changes changes without without further further notice notice to to any any products products or or specifispecifications herein. cations herein. BCD BCD Semiconductor Semiconductor Manufacturing Manufacturing Limited Limited does does not not assume assume any any responsibility responsibility for for use use of of any any its its products products for for any any particular purpose, particular purpose, nor nor does does BCD BCD Semiconductor Semiconductor Manufacturing Manufacturing Limited Limited assume assume any any liability liability arising arising out out of of the the application application or or use use of any of any its its products products or or circuits. circuits. BCD BCD Semiconductor Semiconductor Manufacturing Manufacturing Limited Limited does does not not convey convey any any license license under under its its patent patent rights rights or or other rights other rights nor nor the the rights rights of of others. others. MAIN SITE SITE MAIN - Headquarters BCD Semiconductor Manufacturing Limited BCD Semiconductor Manufacturing Limited - Wafer Fab No. 1600, Zi Xing Road, Shanghai ZiZhu Science-basedLimited Industrial Park, 200241, China Shanghai SIM-BCD Semiconductor Manufacturing Tel: Fax: +86-21-24162277 800,+86-21-24162266, Yi Shan Road, Shanghai 200233, China Tel: +86-21-6485 1491, Fax: +86-21-5450 0008 REGIONAL SALES OFFICE Shenzhen OfficeSALES OFFICE REGIONAL - Wafer FabSemiconductor Manufacturing Limited BCD Shanghai SIM-BCD Semiconductor Manufacturing Co., Ltd. - IC Design Group 800 Yi Shan Road, Shanghai 200233, China Corporation Advanced Analog Circuits (Shanghai) Tel: +86-21-6485 1491,YiFax: 0008200233, China 8F, Zone B, 900, Shan+86-21-5450 Road, Shanghai Tel: +86-21-6495 9539, Fax: +86-21-6485 9673 Taiwan Office Shanghai Semiconductor Manufacturing Co., Ltd., Shenzhen Office BCD Taiwan Semiconductor Shenzhen SIM-BCD Office Office (Taiwan) Company Limited Unit A Room 1203, Skyworth Bldg., Gaoxin Ave.1.S., Nanshan Shenzhen, 4F, 298-1, Guang Road,(Taiwan) Nei-Hu District, Taipei, Shanghai SIM-BCD Semiconductor Manufacturing Co., Ltd.District, Shenzhen Office BCDRui Semiconductor Company Limited China Taiwan Advanced Analog Circuits (Shanghai) Corporation Shenzhen Office 4F, 298-1, Rui Guang Road, Nei-Hu District, Taipei, Tel: +86-755-8826 Tel: +886-2-2656 2808 Room E, 5F, Noble 7951 Center, No.1006, 3rd Fuzhong Road, Futian District, Shenzhen 518026, China Taiwan Fax: +86-755-88267951 7865 Fax: +886-2-2656 28062808 Tel: +86-755-8826 Tel: +886-2-2656 Fax: +86-755-8826 7865 Fax: +886-2-2656 2806 USA Office BCD Office Semiconductor Corp. USA 30920Semiconductor Huntwood Ave.Corporation Hayward, BCD CA 94544, USA Ave. Hayward, 30920 Huntwood Tel :94544, +1-510-324-2988 CA U.S.A Fax:: +1-510-324-2988 +1-510-324-2788 Tel Fax: +1-510-324-2788