Product data sheet Characteristics ATV12H075M2 variable speed drive ATV12 - 0.75kW - 1hp 200..240V - 1ph - with heat sink Range of product Altivar 12 Product or component type Variable speed drive Product destination Asynchronous motors Product specific application Simple machine Assembly style With heat sink Component name ATV12 EMC filter Integrated Built-in fan Without Network number of phases Single phase [Us] rated supply voltage 200...240 V (- 15...10 %) Motor power kW 0.75 kW Motor power hp 1 hp Communication port protocol Modbus Line current 8.5 A, 0...1 kA Speed range 1...20 Transient overtorque 150...170 % of nominal motor torque Asynchronous motor control profile Sensorless flux vector control with PWM type motor control signal IP degree of protection IP20 without blanking plate on upper part Complementary Supply frequency 50/60 Hz (+/- 5 %) Continuous output current 4.2 A at 4 kHz Maximum transient current 6.3 A for 60 s Speed drive output frequency 0...400 Hz Nominal switching frequency 4 kHz Switching frequency 2...16 kHz adjustable 4...16 kHz with derating factor Braking torque Upto 150 % of nominal motor torque with braking resistor at high inertia Upto 70 % of nominal motor torque without braking resistor Regulation loop Adjustable Factory-set with the speed loop stability and gain Motor slip compensation Adjustable Preset in factory Prospective line Isc <= 1 kA Output voltage 200...240 V triphase Electrical connection L1, L2, L3, U, V, W, PA, PC terminal 3.5 mm² (AWG 12) Tightening torque 0.8 N.m Insulation Electrical between power and control Supply Internal supply for logic inputs 24 V DC, voltage limits 20.4...27.6 V 100 mA for overload and short-circuit protection Internal supply for reference potentiometer 5 V DC, voltage limits 4.75...5.25 V 10 mA for overload and short-circuit protection Analogue input number 1 Analogue input type AI1 configurable current 0...20 mA, impedance 250 Ohm AI1 configurable voltage 0...10 V, impedance 30 kOhm AI1 configurable voltage 0...5 V, impedance 30 kOhm 10/8/2011 1 The information provided in this documentation contains general descriptions and/or technical characteristics of the performance of the products contained herein. This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications. It is the duty of any such user or integrator to perform the appropriate and complete risk analysis, evaluation and testing of the products with respect to the relevant specific application or use thereof. Neither Schneider Electric Industries SAS nor any of its affiliates or subsidiaries shall be responsible or liable for misuse of the information contained herein. Main Sampling duration < 10 ms for analogue input 20 ms, tolerance +/- 1 ms for logic input Linearity error +/- 0.3 ms for analogue input Discrete input number 4 Discrete input type LI1...LI4 programmable 24 V, voltage limits 18...30 V Discrete input logic Negative by program, >= 16 V (state 0), < 10 V (state 1) Positive, 0...< 5 V (state 0), >= 11 V (state 1) Discrete output number 3 Discrete output type (CLO) transmitter (LO1) open collector (R1A, R1B, R1C) logic relay 1 C/O Minimum switching current 5 mA at 24 V DC for logic relay Maximum switching current 2 A at 250 V AC inductive load cos phi = 0.4, L/R= L/R = 7 ms for logic relay 2 A at 30 V DC inductive load cos phi = 0.4, L/R= L/R = 7 ms for logic relay 3 A at 250 V AC resistive load cos phi = 1, L/R= L/R = 0 ms for logic relay 4 A at 30 V DC resistive load cos phi = 1, L/R= L/R = 0 ms for logic relay Acceleration and deceleration ramps Linear from 0 to 999.9 s S U Braking to standstill By DC injection, 0.1...30 s Protection type Line supply overvoltage Line supply undervoltage Modbus serial link failure Overcurrent between output phases and earth Overheating protection Safety for no network three-phase Short-circuit between motor phases Thermal protection Insulation resistance >= 500 MOhm Frequency resolution Analog input converter A/D, 10 bits Display unit 0.1 Hz Time constant 20 ms, tolerance +/- 1 ms for reference change Marking CE Operating position Vertical +/- 10 degree Product weight 0.8 kg Environment Electromagnetic compatibility 1.2/50 µs - 8/20 µs surge immunity test (level 3) conforming to EN/IEC 61000-4-5 Electrical fast transient/burst immunity test (level 4) conforming to EN/IEC 61000-4-4 Electrostatic discharge immunity test (level 3) conforming to EN/IEC 61000-4-2 Immunity to conducted disturbances (level 3) conforming to EN/IEC 61000-4-6 Radiated radio-frequency electromagnetic field immunity test (level 3) conforming to EN/IEC 61000-4-3 Standards EN/IEC 61800-3 Product certifications CSA C-Tick GOST NOM UL Vibration resistance 1 gn (f = 13...200 Hz conforming to EN/IEC 60068-2-6 1.5 mm peak to peak (f = 3...13 Hz)drive unmounted on symmetrical DIN rail conforming to EN/IEC 60068-2-6 Shock resistance 15 gn for 11 ms conforming to EN/IEC 60068-2-27 Relative humidity 5...95 % without condensation conforming to IEC 60068-2-3 5...95 % without dripping water conforming to IEC 60068-2-3 Ambient air temperature for storage -25...70 °C Ambient air temperature for operation -10...40 °C with protective cover from the top of the drive removed 40...60 °C with current derating 2.2 % per °C Operating altitude > 1000...2000 m with derating 1 % per 100 m 1000 m without derating RoHS EUR status Compliant RoHS EUR conformity date 0901 2