Low Signal Relay
G6S
Suface Mount DPDT Relay
• High dielectric withstand voltage of 2,000 VAC between coil
and contacts (standard type); 1,500 VAC between contacts
of different polarity.
• Meets FCC Part 68 and Telcordia 2.5 kV surge withstand.
• European version certified for EN60950/EN41003 Supplementary Insulation at 250 V at Pollution Degree 2.
• Low power consumption of 140 mW (Non-latching)
• Available in through-hole and SMT terminals.
• Tape and reel or tube packaging.
• RoHS Compliant.
Ordering Information
■ Standard Version
.
Model
Non-latching
Terminal
Standard
Contact form
Gull-wing
DPDT
European Version*
Single coil latching
Dual coil latching
G6S-2F
G6S-2F-Y
G6SU-2F
Inside “L”
G6S-2G
G6S-2G-Y
G6SU-2G
G6SK-2F
G6SK-2G
PCB through-hole
G6S-2
G6S-2-Y
G6SU-2
G6SK-2
* Certified for EN60950/EN41003 Supplementary Insulation at 250 V (pollution degree 2)
Notes: 1. When ordering, add the rated coil voltage to the model number.
Example: G6S-2F DC12
Rated coil voltage
2. When ordering tape packing (surface mount models), add "-TR" to the model number.
Example: G6S-2F-TR DC12
Tape packing
"-TR" is not part of the relay model number. Therefore, it is not marked on the relay case.
3. Dual coil latching models are available with a High-sensitivity coil. (140 mW; 200 mW for DC24)
When ordering High-sensitivity dual coil latching models, add "-H” to the model number.
Example: G6SK-2G-H-TR DC5
High-sensitivity coil
Model Number Legend
G6S
1
2 3
4
DC
5
6
5. Packaging
None: Tube packaging
TR:
Tape and reel packaging
(Surface mount models)
1. Relay Function
None: Non-latching
U:
Single coil latching
K:
Dual coil latching
3. Terminal Shape
None: Through-hole
F:
Gull-wing surface mount
G:
Inside “L” surface mount
2. Contact Form
2: DPDT
4. Approved Standards
6. Rated Coil Voltage
3, 4.5, 5, 12, 24 VDC
None: UL/CSA
Y:
EN60950/EN41003
(Standard coil models - 5, 12, 24 VDC )
Low Signal Relay
G6S
95
Specification
■ Contact Data
Resistive load (cos φ = 1)
Load
Rated load
0.5 A at 125 VAC
2 A at 30 VDC
Ag (Au clad)
2A
250 VAC, 220 VDC
2A
62.5 VA, 60 W
10 μA, 10 mVDC
Contact material
Max. carry current
Max. operating voltage
Max. operating current
Max. switching capacity
Min. permissible load
Note: P level: λ60 = 0.1 x 10-6/operation
This value was measured at a switching frequency of 120 operations/min and the criterion of contact resistance is 50 Ω. This value may vary
depending on the operating environment. Always double-check relay suitability under actual operating conditions.
■ Coil Data
G6S - Standard Non-latching (G6S-2F, G6S-2G, G6S-2)
Rated
voltage
(VDC)
3
4.5
5
12
24
Rated
current
(mA)
46.7
31.0
28.1
11.7
8.3
Pick-up
voltage
Coil
resistance
(Ω)
64.3
145
178
1,028
2,880
75% max.
Dropout
Maximum
voltage
voltage
% of rated voltage
10% max.
200% max.@ 23°C
Approx. 140
170% max.@ 23°C
Approx. 200
Power consumption (mW)
G6SU - Standard Single Coil Latching (G6SU-2F, G6SU-2G, G6SU-2)
Rated
voltage
(VDC)
3
4.5
5
12
24
Rated
current
(mA)
33.3
22.2
20.0
8.3
6.3
Coil
resistance
(Ω)
90
203
250
1,440
3,840
Coil Inductance (H)
Set pick-up Reset pick-up
Power
Maximum volt(ref. value)
voltage
voltage
consumption
age
(mW)
Armature OFF Armature ON
% of rated voltage
0.108
0.069
75% max.
75% max.
180% max.
Approx. 100
@ 23°C
0.27
0.14
0.36
0.18
2.12
1.14
5.80
3.79
Approx. 150
G6SK - Standard Dual Coil Latching (G6SK-2F, G6SK-2G, G6SK-2)
Rated
voltage
(VDC)
3
4.5
5
12
24
Rated
current
(mA)
66.6
44.4
40
16.7
12.5
Coil
resistance
(Ω)
45
101
125
720
1,920
Coil Inductance (H)
Set
Reset
(ref. value)
pick-up
pick-up
voltage
voltage
Set
Reset
Armature Armature Armature Armature
% of rated voltage
OFF
ON
OFF
ON
0.045
0.035
0.032
0.045
75% max. 75% max.
0.12
0.074
0.082
0.14
0.14
0.088
0.098
0.16
0.60
0.41
0.46
0.54
1.98
1.23
1.34
2.23
Power
Maximum
consumption
voltage
(mW)
170% max. Approx. 200
@ 23°C
140% max. Approx. 300
@ 23°C
G6S - European Version, Non-latching (G6S-2F-Y, G6S-2G-Y, G6S-2-Y)
Rated
voltage
(VDC)
5
12
24
Note: 1.
2.
3.
4.
96
Rated
current
(mA)
40.0
16.7
9.6
Coil
resistance
(Ω)
125
720
2,504
Pick-up
voltage
75% max.
Dropout
Maximum
voltage
voltage
% of rated voltage
10% max.
170% max.@ 23°C
Power consumption (mW)
Approx. 200
Approx. 230
The rated current and coil resistance are measured at a coil temperature of 23°C with a tolerance of ±10%.
The operating characteristics are measured at a coil temperature of 23°C.
Pick-up voltage will vary with temperature.
The maximum voltage is the highest voltage that can be imposed on the relay coil.
Low Signal Relay
G6S
■ Characteristics
Contact resistance (See note 1)
75 mΩ max.
Operate (set) time (See note 2)
4 ms max. (mean value approx. 2.5 ms G6S; 2.0 ms G6SU, G6SK)
Release (reset) time (See note 2)
4 ms max. (mean value approx. 1.5 ms G6S; 2.0 ms G6SU, G6SK)
Bounce time
Approx. 0.5 ms
Max. operating frequency
Mechanical: 36,000 operations/hr
Electrical: 1,800 operations/hr (under rated load)
Insulation resistance (See note 3)
1,000 MΩ min. (at 500 VDC)
Dielectric strength
2,000 VAC, 50/60 Hz for 1 minute (G6S, G6SU) between coil and contacts
1,000 VAC, 50/60 Hz for 1 minute (G6SK) between coil and contacts
1,500 VAC, 50/60 Hz for 1 minute between contacts of different poles
1,000 VAC, 50/60 Hz for 1 minute between contacts of same pole
500 VAC, 50/60 Hz for 1 minute between set and reset coils (G6SK)
Surge withstand voltage
Vibration
Shock
Conforming to
Telcordia specs.
2,500 V (2 x 10 μS) between coil and contacts for G6S and G6SU
2,500 V (2 x 10 μS) between contacts of different poles
Conforming to
FCC Part 68
1,500 V (10 x 160 μS) between coil and contacts for G6SK
1,500 V (10 x 160 μS) between contacts of same pole
Mechanical durability
10 to 55 Hz; 5 mm double amplitude
Malfunction durability
10 to 55 Hz; 3.3 mm double amplitude
Mechanical durability
1,000 m/s2; approx. 100 G
Malfunction durability
750 m/s2; approx. 75 G
Ambient temperature
-40 to +85°C with no icing; -40 to +70°C with no icing (G6SK, DC24 coil)
Ambient Humidity
5% to 85% RH
Service life
Mechanical
100,000,000 operations min. (at 36,000 operations/hour)
Electrical
100,000 operations min. (2A@30VDC, resistive; 1,200 ops/hr.)
100,000 operations min. (0.5A@125VAC, resistive)
See “Characteristic Data”
Weight
Approx. 2g
Note: 1. The contact resistance was measured with 10 mA at 1 VDC with a voltage drop method.
2. Values in parentheses are typical values unless otherwise stated.
3. The insulation resistance was measured with a 500-VDC megohmmeter applied to the same parts as those used for checking
the dielectric strength (except between the set and reset coil).
4. Data shown are of initial value.
■ Characteristic Data
1000
1000
500
500
500
300
300
300
200
100
50
Contact resistance (mΩ)
1000
Contact resistance (mΩ)
Contact resistance (mΩ)
Service Life
200
100
50
200
100
50
30
30
30
20
20
20
10
10
0
0.2
0.6
0.4
6
0.8
Service life (x10 operations)
Resistive load: 10 mA, 10 VDC
Ambient temperature: +85˚
1.0
10
0
0.1
0.3
0.2
6
0.4
Service life (x10 operations)
Resistive load: 100 mA, 28 VDC
Ambient temperature: +85˚
0.5
0
0.2
0.4
0.6
0.8
1.0
Service life (x106 operations)
Resistive load: 100 mA, 50 VDC
Ambient temperature: +85˚
Low Signal Relay
G6S
97
Maximum Switching Capacity
Ambient Temperature vs.
Maximum Coil Voltage
AC resistive load
DC resistive load
Single Coil Latching
Dual Coil Latching
Maximum coil voltage (%)
Maximum coil voltage (%)
Switching current (A)
Non-latching
12 VDC max.
24 VDC
(G6S-Y, 12 VDC max.)
24 VDC
(G6S-Y)
G6SU
G6SK
12 VDC
max.
Ambient temperature (°C)
Switching voltage (V)
G6SK
24 VDC
Ambient temperature (°C)
Note: The maximum coil voltage refers to the maximum value in a varying range of
operating power voltage, not a continuous voltage.
Reference Data
Ambient Temperature vs. Switching Current
Single Coil Latching
Dual Coil Latching
Operating current (A)
Switching current (A)
Non-latching
12 VDC max.
24 VDC
(G6S-Y)
G6SU
12 VDC max.
G6SU
24 VDC
G6SK
12 VDC max.
24 VDC
(G6S-Y, 12 VDC
max.)
G6SK
24 VDC
Ambient temperature (°C)
Ambient temperature (°C)
Electrical Service Life
Dielectric Strength (Standard Version, Non-latching)
Detecting current: 1mA
500
50
50
40
40
Number of contacts (pcs.)
4
Service life (x10 operations)
100
30 VDC
70
50
30
Number of contacts (pcs.)
300
200
30
20
20
125 VAC
10
10
10
0
0.4
0.8
1.2
1.6
Rated operating current (A)
2.0
0
0
1000
1500
2000
2500
3000
Breakdown voltage (V)
Between coil and contacts
98
30
Low Signal Relay
G6S
3500
1000
1500
2000
2500
3000
Breakdown voltage (V)
Between contacts of different poles
Between contacts of same pole.
3500
Impulse Withstand Voltage (Standard Version, Non-latching)
(2 x 10 ms)
(10 x 160 ms)
3
3500
4000
4500
5000
Breakdown voltage (V)
5500
9
Number of contacts (pcs.)
Number of contacts (pcs.)
Number of contacts (pcs.)
6
0
(10 x 160 ms)
15
9
10
5
0
1500
6000
2000
2500
3000
3500
Breakdown voltage (V)
Between contacts of same pole
Between coil and contacts
6
3
0
4000
3500
4000
4500
5000 5500
Breakdown voltage (V)
6000
Between coil and contacts
Between contacts of different poles
Impulse Withstand Voltage (European version)
(2 x 10 ms)
(10 x 160 ms)
9
6
3
4000
4500
5000
5500 6000
Breakdown voltage (V)
10
5
0
1500
6500
Number of contacts (pcs.)
Number of contacts (pcs.)
Number of contacts (pcs.)
9
0
(10 x 160 ms)
15
2000
2500
3000
3500
Breakdown voltage (V)
4000
3
0
4000
4500
5000
5500
6000
Breakdown voltage (V)
6500
Between coil and contacts
Between contacts of different poles
Between contacts of same pole
Between coil and contacts
Between contacts of different poles
6
Dielectric Strength (European Version, Non-latching)
50
50
40
40
Number of contacts (pcs.)
Number of contacts (pcs.)
Detecting current: 1mA
30
20
30
20
10
10
0
0
1500
2000
2500
3000
3500
Breakdown voltage (V)
Between coil and contacts
4000
1500
2000
2500
3000
3500
Breakdown voltage (V)
4000
Between contacts of different poles
Between contacts of same pole
Low Signal Relay
G6S
99
Dimensions
Note: 1. All units are in millimeters unless otherwise indicated.
2. Coplanarity is 0.1 mm max.
■ Standard
G6S-2F, G6S-2F-Y
Tolerance: ±0.3
Terminal Arrangement/
Internal Connections
(Top View)
Footprint
(Top View)
Tolerance: ±0.1
Orientation mark
G6S-2G, G6S-2G-Y
Tolerance: ±0.3
Terminal Arrangement/
Internal Connections
(Top View)
Footprint
(Top View)
Tolerance: ±0.1
Orientation mark
G6S-2, G6S-2-Y
Tolerance: ±0.3
Terminal Arrangement/
Internal Connections
(Bottom View)
Orientation mark
100
Low Signal Relay
G6S
Footprint
(Bottom View)
Tolerance: ±0.1
Eight, 1-dia. holes
■ Single Coil Latching
G6SU-2F
Tolerance: ±0.3
Terminal Arrangement/
Internal Connections
(Top View)
7.3+0.2
G6SU-2G
Tolerance: ±0.3
7.3+0.2
Orientation mark
Terminal Arrangement/
Internal Connections
(Top View)
Footprint
(Top View)
Tolerance: ±0.1
Footprint
(Top View)
Tolerance: ±0.1
Orientation mark
G6SU-2
Tolerance: ±0.3
Terminal Arrangement/
Internal Connections
(Bottom View)
Footprint
(Bottom View)
Tolerance: ±0.1
Eight, 1-dia. holes
Orientation mark
Low Signal Relay
G6S
101
■ Dual Coil Latching
G6SK-2F
Tolerance: ±0.3
Terminal Arrangement/
Internal Connections
(Top View)
Footprint
(Top View)
Tolerance: ±0.1
Orientation mark
G6SK-2G
Tolerance: ±0.3
7.3+0.2
Terminal Arrangement/
Internal Connections
(Top View)
Footprint
(Top View)
Tolerance: ±0.1
Orientation mark
G6SK-2
Tolerance: ±0.3
Terminal Arrangement/
Internal Connections
(Bottom View)
Footprint
(Bottom View)
Tolerance: ±0.1
Orientation mark
Ten, 1-dia. holes
Recommended Soldering Method
(1) IRS Method (Mounting Solder: Lead)
(2) IRS Method (Mounting Solder: Lead-free)
Soldering
Soldering
220 to
240
180 to
200
150
Preheating
Preheating
90 to 120
20 to 30
Time (s)
102
Low Signal Relay
G6S
Temperature (°C)
Temperature (°C)
Upper surface of case (peak):
255°C max.
Soldering
250 max.
230
180
150
Preheating
Relay
terminal
section
120 max.
30 max.
Time (s)
Note: The temperature profile indicates the
temperature of the relay terminal section.
Packaging
Tube packing
Standard nomenclature
Tape packing (Surface mount versions)
When ordering, add “TR” before the rated coil voltage (e.g., G6S-2F-TR-DC12)
Note: TR is not part of the relay model number and will not be marked on the relay.
50 pcs per anti-static tube
■ Tape and Reel Dimensions (Surface Mount Models)
•
•
•
•
Tape type: TE2416R (Refer to EIAJ - Electronic Industrial Association of Japan)
Reel type: R24E (Refer to EIAJ - Electronic Industrial Association of Japan)
Relays per reel: 400
Reels per packing carton: 2 (800 relays)
29.5±1.0
G6S-2F, G6SU-2F, G6SK-2F, G6S-2F-Y
25.5±0.5
2±0.3
2±10.5
330
80
R1.0
13±0.2
G6S-2G, G6SU-2G, G6SK-2G, G6S-2G-Y
Cover tape
Carrier tape
Emboss tape
Orientation mark
Feed direction
■ Approvals
UL Recognized (File No. E41515) / CSA Certified (File No. LR31928) - - Ambient Temp. = 40°C
Type
G6S-2, G6S-2F, G6S-2G
Contact form
DPDT
Coil rating
2 to 48 VDC
2 to 24 VDC
G6SU-2, G6SU-2F, G6SU-2G
G6SK-2, G6SK-2F, G6SK-2G
G6SK-2-Y, G6SK-2F-Y, G6SK-2G-Y
Contact ratings
Number of test operations
6,000
3 A at 30 VDC (Resistive)
0.3 A at 110 VDC (Resistive)
0.5 A at 125 VAC (General Use)
EN60950 / EN41003
Type
G6S-2-Y, G6S-2F-Y, G6S-2G-Y
Contact form
DPDT
Isolation Category
Supplementary Isolation
Voltage
250 VAC
Note: 1. The rated values approved by each of the safety standards (e.g., UL and CSA) may be different from the performance characteristics
individually defined in this catalog.
2. In the interest of product improvement, specifications are subject to change.
Low Signal Relay
G6S
103
Precautions
• Use a DC power supply with 5% or less ripple factor to operate the coil.
• Do not use the G6S where subject to strong external magnetic fields.
• Do not use the G6S where subject to magnetic particles or excessive
amounts of dust.
• Do not reverse the polarity of the coil (+, −).
• Latching types are delivered in the reset position. We recommend
that a reset voltage be applied in advance to start operation.
• Do not drop the G6S or otherwise subject it to excessive shock.
• Remove the relay from the packing immediately prior to usage.
■ Correct use
Long-term Continuously ON Contacts
G6S (K) (-U) -2 Soldering
Using the Relay in a circuit where the Relay will be ON continuously
for long periods (without switching) can lead to unstable contacts
because the heat generated by the coil itself will affect the insulation,
causing a film to develop on the contact surfaces. We recommend
using a latching relay (magnetic-holding relay) in this kind of circuit. If
a single-side stable model must be used in this kind of circuit, we recommend using a fail-safe circuit design that provides protection
against contact failure or coil burnout.
• Soldering temperature: Approx. 250°C (At 260°C if the DWS
method is used.)
• Soldering time: Approx. 5 s max. (Approx. 2 s for the first time and
approx. 3 s for the second time if the DWS method is used.)
• Be sure to adjust the level of the molten solder so that the solder
will not overflow onto the PCB.
Relay Handling
During automatic insertion of Relays, be sure to set the securing
force of each claw to the following so that the Relay’s characteristics
will be maintained.
Use the Relay as soon as possible after opening the moisture-proof
package. If the Relay is left for a long time after opening the moisture-proof package, the appearance may suffer and seal failure may
occur after the solder mounting process. To store the Relay after
opening the moisture-proof package, place it into the original package and sealed the package with adhesive tape.
When washing the product after soldering the Relay to a PCB, use a
water-based solvent or alcohol-based solvent, and keep the solvent
temperature to less than 40°C. Do not put the Relay in a cold cleaning bath immediately after soldering.
104
Low Signal Relay
G6S
Claw Securing Force During Automatic Mounting
C
A
B
Dimension A: 1.96 N max.
Dimension B: 4.90 N max.
Dimension C: 1.96 N max.
Omron Electronic Components, LLC
Terms and Conditions of Sales
I. GENERAL
1. Definitions: The words used herein are defined as follows.
(a) Terms:
These terms and conditions
(b) Seller:
Omron Electronic Components LLC and its subsidiaries
(c) Buyer:
The buyer of Products, including any end user in section III through VI
(d) Products: Products and/or services of Seller
(e) Including: Including without limitation
2. Offer; Acceptance: These Terms are deemed part of all quotations, acknowledgments,
invoices, purchase orders and other documents, whether electronic or in writing, relating
to the sale of Products by Seller. Seller hereby objects to any Terms proposed in Buyer's
purchase order or other documents which are inconsistent with, or in addition to, these
Terms.
3. Distributor: Any distributor shall inform its customer of the contents after and including
section III of these Terms.
II. SALES
1. Prices; Payment: All prices stated are current, subject to change without notice by Seller.
Buyer agrees to pay the price in effect at the time the purchase order is accepted by
Seller. Payments for Products received are due net 30 days unless otherwise stated in
the invoice. Buyer shall have no right to set off any amounts against the amount owing in
respect of this invoice.
2. Discounts: Cash discounts, if any, will apply only on the net amount of invoices sent to
Buyer after deducting transportation charges, taxes and duties, and will be allowed only
if (a) the invoice is paid according to Seller's payment terms and (b) Buyer has no past
due amounts owing to Seller.
3. Interest: Seller, at its option, may charge Buyer 1.5% interest per month or the maximum
legal rate, whichever is less, on any balance not paid within the stated terms.
4. Orders: Seller will accept no order less than 200 U.S. dollars net billing.
5. Currencies: If the prices quoted herein are in a currency other than U.S. dollars, Buyer
shall make remittance to Seller at the then current exchange rate most favorable to
Seller; provided that if remittance is not made when due, Buyer will convert the amount
to U.S. dollars at the then current exchange rate most favorable to Seller available
during the period between the due date and the date remittance is actually made.
6. Governmental Approvals: Buyer shall be responsible for all costs involved in obtaining
any government approvals regarding the importation or sale of the Products.
7. Taxes: All taxes, duties and other governmental charges (other than general real
property and income taxes), including any interest or penalties thereon, imposed directly
or indirectly on Seller or required to be collected directly or indirectly by Seller for the
manufacture, production, sale, delivery, importation, consumption or use of the Products
sold hereunder (including customs duties and sales, excise, use, turnover and license
taxes) shall be charged to and remitted by Buyer to Seller.
8. Financial: If the financial position of Buyer at any time becomes unsatisfactory to Seller,
Seller reserves the right to stop shipments or require satisfactory security or payment in
advance. If Buyer fails to make payment or otherwise comply with these Terms or any
related agreement, Seller may (without liability and in addition to other remedies) cancel
any unshipped portion of Products sold hereunder and stop any Products in transit until
Buyer pays all amounts, including amounts payable hereunder, whether or not then due,
which are owing to it by Buyer. Buyer shall in any event remain liable for all unpaid
accounts.
9. Cancellation; Etc: Orders are not subject to rescheduling or cancellation unless Buyer
indemnifies Seller fully against all costs or expenses arising in connection therewith.
10. Force Majeure: Seller shall not be liable for any delay or failure in delivery resulting from
causes beyond its control, including earthquakes, fires, floods, strikes or other labor
disputes, shortage of labor or materials, accidents to machinery, acts of sabotage, riots,
delay in or lack of transportation or the requirements of any government authority.
11. Shipping; Delivery: Unless otherwise expressly agreed in writing by Seller:
(a) All sales and shipments of Products shall be FOB shipping point (unless otherwise
stated in writing by Seller), at which point title to and all risk of loss of the Products
shall pass from Seller to Buyer, provided that Seller shall retain a security interest in
the Products until the full purchase price is paid by Buyer;
(b) Delivery and shipping dates are estimates only; and
(c) Seller will package Products as it deems proper for protection against normal
handling and extra charges apply to special conditions.
12. Claims: Any claim by Buyer against Seller for shortage or damage to the Products
occurring before delivery to the carrier or any claim related to pricing or other charges
must be presented in detail in writing to Seller within 30 days of receipt of shipment.
III. PRECAUTIONS
1. Suitability: IT IS THE BUYER’S SOLE RESPOINSIBILITY TO ENSURE THAT ANY
OMRON PRODUCT IS FIT AND SUFFICIENT FOR USE IN A MOTORIZED VEHICLE
APPLICATION. BUYER SHALL BE SOLELY RESPONSIBLE FOR DETERMINING
APPROPRIATENESS OF THE PARTICULAR PRODUCT WITH RESPECT TO THE
BUYER’S APPLICATION INCLUDING (A) ELECTRICAL OR ELECTRONIC
COMPONENTS, (B) CIRCUITS, (C) SYSTEM ASSEMBLIES, (D) END PRODUCT, (E)
SYSTEM, (F) MATERIALS OR SUBSTANCES OR (G) OPERATING ENVIRONMENT.
Buyer acknowledges that it alone has determined that the Products will meet their
requirements of the intended use in all cases. Buyer must know and observe all
prohibitions of use applicable to the Product/s.
2. Use with Attention: The followings are some examples of applications for which
particular attention must be given. This is not intended to be an exhaustive list of all
possible use of any Product, nor to imply that any use listed may be suitable for any
Product:
(a) Outdoor use, use involving potential chemical contamination or electrical
interference.
(b) Use in consumer Products or any use in significant quantities.
(c) Energy control systems, combustion systems, railroad systems, aviation systems,
medical equipment, amusement machines, vehicles, safety equipment, and
installations subject to separate industry or government regulations.
(d) Systems, machines, and equipment that could present a risk to life or property.
3. Prohibited Use: NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING
SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM
AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE
PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE
WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
4. Motorized Vehicle Application: USE OF ANY PRODUCT/S FOR A MOTORIZED
VEHICLE APPLICATION MUST BE EXPRESSLY STATED IN THE SPECIFICATION BY
SELLER.
5. Programmable Products: Seller shall not be responsible for the Buyer's programming of
a programmable Product.
IV. WARRANTY AND LIMITATION
1. Warranty: Seller's exclusive warranty is that the Products will be free from defects in
materials and workmanship for a period of twelve months from the date of sale by Seller
(or such other period expressed in writing by Seller). SELLER MAKES NO WARRANTY
OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT ALL OTHER WARRANTIES,
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE OF THE PRODUCTS.
2. Buyer Remedy: Seller's sole obligation hereunder shall be to replace (in the form
originally shipped with Buyer responsible for labor charges for removal or replacement
thereof) the non-complying Product or, at Seller's election, to repay or credit Buyer an
amount equal to the purchase price of the Product; provided that there shall be no
liability for Seller or its affiliates unless Seller's analysis confirms that the Products were
correctly handled, stored, installed and maintained and not subject to contamination,
abuse, misuse or inappropriate modification. Return of any Products by Buyer must be
approved in writing by Seller before shipment.
3. Limitation on Liability: SELLER AND ITS AFFILIATES SHALL NOT BE LIABLE FOR
SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF
PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED
WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT,
WARRANTY, NEGLIGENCE OR STRICT LIABILITY. FURTHER, IN NO EVENT SHALL
LIABILITY OF SELLER OR ITS AFFILITATES EXCEED THE INDIVIDUAL PRICE OF
THE PRODUCT ON WHICH LIABILITY IS ASSERTED.
4. Indemnities: Buyer shall indemnify and hold harmless Seller, its affiliates and its
employees from and against all liabilities, losses, claims, costs and expenses (including
attorney's fees and expenses) related to any claim, investigation, litigation or proceeding
(whether or not Seller is a party) which arises or is alleged to arise from Buyer's acts or
omissions under these Terms or in any way with respect to the Products.
V. INFORMATION; ETC.
1. Intellectual Property: The intellectual property embodied in the Products is the exclusive
property of Seller and its affiliates and Buyer shall not attempt to duplicate it in any way
without the written permission of Seller. Buyer (at its own expense) shall indemnify and
hold harmless Seller and defend or settle any action brought against Seller to the extent
that it is based on a claim that any Product made to Buyer specifications infringed
intellectual property rights of another party.
2. Property; Confidentiality: Notwithstanding any charges to Buyer for engineering or
tooling, all engineering and tooling shall remain the exclusive property of Seller. All
information and materials supplied by Seller to Buyer relating to the Products are
confidential and proprietary, and Buyer shall limit distribution thereof to its trusted
employees and strictly prevent disclosure to any third party.
3. Performance Data: Performance data is provided as a guide in determining suitability
and does not constitute a warranty. It may represent the result of Seller's test conditions,
and the users must correlate it to actual application requirements.
4. Change In Specifications: Product specifications and descriptions may be changed at
any time based on improvements or other reasons. It is Seller’s practice to change part
numbers when published ratings or features are changed, or when significant
engineering changes are made. However, some specifications of the Product may be
changed without any notice.
5. Errors And Omissions: The information on Seller’s website or in other documentation
has been carefully checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
6. Export Controls: Buyer shall comply with all applicable laws, regulations and licenses
regarding (a) export of the Products or information provided by Seller; (b) sale of
Products to forbidden or other proscribed persons or organizations; (c) disclosure to noncitizens of regulated technology or information.
VI. MISCELLANEOUS
1. Waiver: No failure or delay by Seller in exercising any right and no course of dealing
between Buyer and Seller shall operate as a waiver of rights by Seller.
2. Assignment: Buyer may not assign its rights hereunder without Seller's written consent.
3. Law: These Terms are governed by Illinois law (without regard to conflict of laws).
Federal and state courts in Cook County, Illinois have exclusive jurisdiction for any
dispute hereunder.
4. Amendment: These Terms constitute the entire agreement between Buyer and Seller
relating to the Products, and no provision may be changed or waived unless in writing
signed by the parties.
5. Severability: If any provision hereof is rendered ineffective or invalid, such provision shall
not invalidate any other provision.
Low Signal Relay
G6S
Certain Precautions on Specifications and Use
1. Suitability for Use. Seller shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in
Buyer's application or use of the Product. At Buyer's request, Seller will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not
sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use.
Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer's application, product or system. Buyer
shall take application responsibility in all cases but the following is a nonexhaustive list of applications for which particular attention must be given:
(i) Outdoor use, uses involving potential chemical contamination or electrical
interference, or conditions or uses not described in this document.
(ii) Energy control systems, combustion systems, railroad systems, aviation
systems, medical equipment, amusement machines, vehicles, safety
equipment, and installations subject to separate industry or government
regulations.
(iii) Use in consumer products or any use in significant quantities.
(iv) Systems, machines and equipment that could present a risk to life or
property. Please know and observe all prohibitions of use applicable to this
product.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM
AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT
THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE
INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
2. Programmable Products. Seller shall not be responsible for the user's programming of a programmable product, or any consequence thereof.
3. Performance Data. Performance data given in this publication is provided as
a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Seller's test conditions, and the users must
correlate it to actual application requirements. Actual performance is subject to
Seller's Warranty and Limitations of Liability.
4. Change in Specifications. Product specifications and accessories may be
changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed,
or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for
your application. Please consult with your Seller representative at any time to
confirm actual specifications of purchased Product.
5. Errors and Omissions. The information in this publication has been carefully
checked and is believed to be accurate; however, no responsibility is assumed
for clerical, typographical or proofreading errors, or omissions.
6. RoHS Compliance. Where indicated, our products currently comply, to the
best of our knowledge as of the date of this publication, with the requirements
of the European Union's Directive on the Restriction of certain Hazardous
Substances ("RoHS"), although the requirements of RoHS do not take effect
until July 2006. These requirements may be subject to change. Please consult
our website for current information.
Complete “Terms and Conditions of Sale” for product purchase and use are on Omron’s website
at http://www.components.omron.com – under the “About Us” tab, in the Legal Matters section.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
OMRON ON-LINE
OMRON ELECTRONIC
COMPONENTS LLC
55 E. Commerce Drive, Suite B
Schaumburg, IL 60173
Global - http://www.omron.com
USA - http://www.components.omron.com
847-882-2288
Cat. No. X301-E-1a
Low Signal Relay
03/10
G6S
Specifications subject to change without notice
Printed in USA