TI TLE2426-EP

SGLS345 − JUNE 2006
D Controlled Baseline
D
D
D
D
D
D
D
D
D Excellent Output Regulation
− One Assembly/Test Site, One Fabrication
Site
Extended Temperature Performance of
−55°C to 125°C
Enhanced Diminishing Manufacturing
Sources (DMS) Support
Enhanced Product-Change Notification
Qualification Pedigree†
One-Half VI Virtual Ground for Analog
Systems
Micropower Operation . . . 170 µA Typ,
VI = 5 V
Wide VI Range . . . 4 V to 40 V
High Output-Current Capability
− Source . . . 20 mA Typ
− Sink . . . 20 mA Typ
D
D
− −102 µV Typ at IO = 0 mA to −10 mA
− 49 µV Typ at IO = 0 mA to 10 mA
Low-Impedance Output . . . 0.0075 Ω Typ
Noise Reduction Pin
† Component qualification in accordance with JEDEC and industry
standards to ensure reliable operation over an extended
temperature range. This includes, but is not limited to, Highly
Accelerated Stress Test (HAST) or biased 85/85, temperature
cycle, autoclave or unbiased HAST, electromigration, bond
intermetallic life, and mold compound life. Such qualification
testing should not be viewed as justifying use of this component
beyond specified performance and environmental limits.
D PACKAGE
(TOP VIEW)
OUT
COMMON
IN
NC
−
description/ordering information
1
8
2
7
3
6
4
5
NOISE REDUCTION
NC
NC
NC
NC − No internal connection
In signal-conditioning applications utilizing a
single power source, a reference voltage equal to
one-half the supply voltage is required for
termination of all analog signal grounds. TI
presents a precision virtual ground whose output
voltage is always equal to one-half the input
voltage—the TLE2426 rail splitter.
10
VI
VI
VO
V
V + I
O
2
8
Voltage − V
The unique combination of a high-performance,
micropower operational amplifier and a precisiontrimmed divider on a single silicon chip results in
a precise VO/VI ratio of 0.5 while sinking and
sourcing current. The TLE2426 provides a lowimpedance output with 20 mA of sink and source
capability, while drawing less than 280 µA of
supply current over the full input range of 4 V to
40 V. A designer need not pay the price in terms
of board space for a conventional signal ground
consisting of resistors, capacitors, operational
amplifiers, and voltage references. For increased
performance, the 8-pin package provides a
noise-reduction pin. With the addition of an
external capacitor (CNR), peak-to-peak noise is
reduced, while line ripple rejection is improved.
INPUT/OUTPUT TRANSFER CHARACTERISTICS
6
VO
4
2
0
0
0.25
0.5
0.75
1
t − Time − s
Initial output tolerance for a single 5-V or 12-V system is better than 1% over the full 40-V input range. Ripple
rejection exceeds 12 bits of accuracy. Whether the application is for a data-acquisition front end, analog signal
termination, or simply a precision voltage reference, the TLE2426 eliminates a major source of system error.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2006 Texas Instruments Incorporated
! "#$ %!&
% "! "! '! ! !( !
%% )*& % "!+ %! !!$* $%!
!+ $$ "!!&
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SGLS345 − JUNE 2006
ORDERING INFORMATION
PACKAGE†
TA
ORDERABLE
PART NUMBER
TOP-SIDE
MARKING
−55°C to 125°C
SOIC (D)
Tape and reel
TLE2426MDREP
2426EP
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design
guidelines are available at www.ti.com/sc/package.
absolute maximum ratings over operating free-air temperature (unless otherwise noted)†
Continuous input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 V
Continuous filter trap voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 V
Output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 80 mA
Duration of short-circuit current at (or below) 25°C (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unlimited
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature range, TA
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −55°C to 125°C
Operating junction temperature, TJ (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
Storage temperature range, Tstg (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
Lead temperature 1,6 mm (1/16 in) from case for 10 s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The output may be shorted to either supply. Temperature and/or supply voltages must be limited to ensure that the maximum
dissipation rating is not exceeded.
2. Long-term high-temperature storage and/or usage at the absolute maximum ratings may result in a reduction of overall device life.
See http://www.ti.com/ep_quality for additional information on enhanced plastic packaging.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25
25°C
C
POWER RATING
D
1102 mV
DERATING FACTOR
ABOVE TA = 25°C
10.3 mW/°C
TA = 70
70°C
C
POWER RATING
TA = 85
85°C
C
POWER RATING
TA = 125
125°C
C
POWER RATING
638.5 mW
484 mW
72.1 mW
recommended operating conditions
Input voltage, VI
Operating free-air temperature, TA
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MIN
MAX
4
40
UNIT
V
−55
125
°C
SGLS345 − JUNE 2006
electrical characteristics at specified free-air temperature, VI = 5 V, IO = 0 (unless otherwise noted)
PARAMETER
Output voltage
TEST CONDITIONS
VI = 4 V
VI = 5 V
25°C
25
C
VI = 40 V
VI = 5 V
Full range
Temperature coefficient of output
voltage
VI = 5 V
Supply current
No load
TA†
VI = 4 to 40 V
Output voltage regulation
(sinking current)‡
IO = 0 to − 10 mA
TYP
MAX
1.98
2
2.02
2.48
2.5
2.52
19.8
20
20.2
2.465
25
25°C
170
IO = 0 to 8 mA
IO = 0 to 20 mA
350
400
−0.102
± 0.7
25°C
−0.121
± 1.4
25°C
0.049
± 0.5
0.175
± 1.4
22.5
± 10
± 10
Full range
Output impedance‡
25°C
7.5
Noise-reduction impedance
25°C
110
Short-circuit current
Output noise voltage, rms
Sinking current, VO = 5 V
VO to 0.1%, IO = ± 10 mA
Output voltage current step response
VO to 0.01%, IO = ± 10 mA
Step response
VI = 0 to 5 V, VO to 0.1%
VI = 0 to 5 V, VO to 0.01%
µA
mV
mV
mΩ
kΩ
26
25°C
Sourcing current, VO = 0
f = 10 Hz to 10 kHz
300
25°C
25°C
V
ppm/°C
Full range
Full range
IO = 0 to − 20 mA
IO = 0 to 10 mA
UNIT
2.535
Full range
25°C
Output voltage regulation
(sourcing current)‡
MIN
CNR = 0
CNR = 1 µF
CL = 0
CL = 100 pF
CL = 0
CL = 100 pF
CL = 100 pF
−47
120
25°C
30
mA
µV
V
290
25°C
275
400
25°C
25°C
µss
390
20
120
µs
† Full range is −55°C to 125°C.
‡ The listed values are not production tested.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SGLS345 − JUNE 2006
electrical characteristics at specified free-air temperature, VI = 12 V, IO = 0 (unless otherwise noted)
PARAMETER
Output voltage
TEST CONDITIONS
VI = 4 V
VI = 12 V
25°C
25
C
VI = 40 V
VI = 12 V
Full range
Temperature coefficient of output voltage
VI = 12 V
Supply current
TA†
No load
VI = 4 to 40 V
IO = 0 to − 10 mA
Output voltage regulation
(sinking current)‡
IO = 0 to 8 mA
IO = 0 to 20 mA
TYP
MAX
1.98
2
2.02
5.95
6
6.05
19.8
20
20.2
5.925
35
25°C
195
350
400
−1.48
±10
−3.9
±10
25°C
2.27
±10
±10
4.3
±10
22.5
Output impedance‡
25°C
7.5
Noise-reduction impedance
25°C
110
Short-circuit current
Output noise voltage, rms
CNR = 1 µF
Output voltage current step response
VO to 0.01%, IO = ± 10 mA
Step response
25°C
CNR = 0
VO to 0.1%, IO = ± 10 mA
VI = 0 to 12 V, VO to 0.1%
VI = 0 to 12 V, VO to 0.01%
CL = 0
CL = 100 pF
CL = 0
CL = 100 pF
CL = 100 pF
† Full range is −55°C to 125°C.
‡ The listed values are not production tested.
4
POST OFFICE BOX 655303
mV
mV
mΩ
kΩ
31
Sourcing current, VO = 0
f = 10 Hz to 10 kHz
µA
±10
25°C
Full range
Sinking current, VO = 12 V
ppm/°C
25°C
25°C
V
300
Full range
Full range
IO = 0 to − 20 mA
IO = 0 to 10 mA
UNIT
6.075
Full range
25°C
Output voltage regulation
(sourcing current)‡
MIN
• DALLAS, TEXAS 75265
−70
120
25°C
30
mA
µV
V
290
25°C
275
400
25°C
25°C
µss
390
12
120
µs
SGLS345 − JUNE 2006
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
Output voltage
Distribution
Output voltage change
vs Free-air temperature
3
Output voltage error
vs Input voltage
4
vs Input voltage
5
Input bias current
1, 2
vs Free-air temperature
6
Output voltage regulation
vs Output current
7
Output impedance
vs Frequency
8
Short-circuit output current
vs Input voltage
9, 10
vs Free-air temperature
11, 12
Ripple rejection
vs Frequency
13
Spectral noise voltage density
vs Frequency
14
Output voltage response to output current step
vs Time
15
Output voltage power-up response
vs Time
16
Output current
vs Load capacitance
17
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SGLS345 − JUNE 2006
TYPICAL CHARACTERISTICS†
DISTRIBUTION
OF
OUTPUT VOLTAGE
DISTRIBUTION
OF
OUTPUT VOLTAGE
3
Percentage of Units − %
Percentage of Units − %
2.5
40
98 Units Tested
From 2 Wafer Lots
VI = 5 V
TA = 25°C
2
1.5
1
98 Units Tested
From 2 Wafer Lots
VI = 12 V
TA = 25°C
30
20
10
0.5
0
2.48
0
2.49
2.5
2.51
VO − Output Voltage − V
2.52
6.05
6.075
6.025
VO − Output Voltage − V
6
Figure 1
Figure 2
OUTPUT VOLTAGE ERROR
vs
INPUT VOLTAGE
OUTPUT VOLTAGE CHANGE
vs
FREE-AIR TEMPERATURE
4
150
IO = 0
TA = 25°C
IO = 0
3
75
Output Voltage Error − %
VO − Output Voltage Change − mV
∆V
O
VI = 40 V
VI = 12 V
0
VI = 4 V, 5 V
Error Equals VO / VI Deviation From 50%
2
1
−75
0
−150
−75
−1
−50
−25
0
25
50
75
100
125
0
4
TA − Free-Air Temperature − °C
8
12
16
20
24
28
32
VI − Input Voltage − V
Figure 3
Figure 4
† Data at high and low temperatures are applicable within the rated operating free-air temperature ranges of the various devices.
6
6.1
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
36
40
SGLS345 − JUNE 2006
TYPICAL CHARACTERISTICS†
INPUT BIAS CURRENT
vs
INPUT VOLTAGE
INPUT BIAS CURRENT
vs
FREE-AIR TEMPERATURE
300
300
IO = 0
VI = 40 V
250
TA = 25°C
IIB
I IB − Input Bias Current − µ A
IIB
I IB − Input Bias Current − µ A
250
200
TA = − 55°C
150
TA = 125°C
100
VI = 12 V
200
VI = 5 V
150
VI = 4 V
100
50
50
IO = 0
0
0
0
5
10
15
20
25
30
35
40
−75
−50
VI − Input Voltage − V
OUTPUT VOLTAGE REGULATION
vs
OUTPUT CURRENT
OUTPUT IMPEDANCE
vs
FREQUENCY
200
VI = 5 V or 12 V
IO = 0
TA = 25°C
VI = 5 V
TA = 25°C
10
z o − Output Impedance − Ω
Output Voltage Regulation − µV
100
100
50
0
125
Figure 6
Figure 5
150
75
100
0
25
50
−20
TA − Free-Air Temperature − °C
TYP
−50
−100
1
0.1
0.01
−150
−200
−20
0.001
0
10
−10
IO − Output Current − mA
20
10
100
1k
10 k
100 k
1M
f − Frequency − Hz
Figure 7
Figure 8
† Data at high and low temperatures are applicable within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
SGLS345 − JUNE 2006
TYPICAL CHARACTERISTICS†
SHORT-CIRCUIT OUTPUT CURRENT
vs
INPUT VOLTAGE
SHORT-CIRCUIT OUTPUT CURRENT
vs
INPUT VOLTAGE
40
VO = GND
(Output Sourcing)
IOS
I OS − Short-Circuit Output Current − mA
IOS
I OS − Short-Circuit Output Current − mA
0
−20
−40
TA = − 55°C
−60
TA = 125°C
TA = 25°C
TA = 25°C
TA = − 55°C
30
TA = 125°C
20
10
VO = VI
(Output Sinking)
0
−80
0
5
10
15
20
25
30
35
0
40
5
Figure 9
25
30
40
VI = 40 V
VO = GND
(Output Sourcing)
VI = 4 V
−20
−30
VI = 5 V
−40
−50
VI = 12 V
−60
−70
VI = 40 V
−50
−25
0
25
50
75
100
125
VI = 12 V
30
VI = 5 V
VI = 4 V
20
10
VO = VI
(Output Sinking)
0
−75
−50
TA − Free-Air Temperature − °C
−25
0
25
50
75
TA − Free-Air Temperature − °C
Figure 12
Figure 11
† Data at high and low temperatures are applicable within the rated operating free-air temperature ranges of the various devices.
8
35
40
IOS
I OS − Short-Circuit Output Current − mA
IOS
I OS − Short-Circuit Output Current − mA
20
SHORT-CIRCUIT OUTPUT CURRENT
vs
FREE-AIR TEMPERATURE
0
−80
−75
15
Figure 10
SHORT-CIRCUIT OUTPUT CURRENT
vs
FREE-AIR TEMPERATURE
−10
10
VI − Input Voltage − V
VI − Input Voltage − V
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
100
125
SGLS345 − JUNE 2006
TYPICAL CHARACTERISTICS
RIPPLE REJECTION
vs
FREQUENCY
SPECTRAL NOISE VOLTAGE DENSITY
vs
FREQUENCY
400
VI = 5 V or 12 V
∆VI(PP) = 1 V
IO = 0
TA = 25°C
90
Ripple Rejection − dB
80
Vn − Spectral Noise Voltage Density − nV/ Hz
100
CNR = 1 µF
70
60
50
40
30
20
CNR = 0
10
VI = 5 V or 12 V
TA = 25°C
300
200
100
CNR = 0
CNR = 1 µF
0
0
10
100
1k
10 k
100 k
10
1
1M
100
1k
f − Frequency − Hz
f − Frequency − Hz
Figure 13
Figure 14
OUTPUT VOLTAGE RESPONSE
TO OUTPUT CURRENT STEP
10 k
OUTPUT VOLTAGE POWER-UP RESPONSE
3
1.5 V
0.1%
3
0.1%
VI = 5 V
CL = 100 pF
TA = 25°C
Output Voltage Response
2
1
0.01%
0
0.01%
−1
−2
10 mA
−3
IO Step
0.01%
2.5
VV)
O − Output Voltage − V
4
∆V
VO
O − Change In Output Voltage − mV
100 k
0.1%
2
1.5
IO = 0
CL = 100 pF
TA = 25°C
1
0.5
0
5
Input Voltage Step
−4
−10 mA
−1.5 V
0
1000
2000
3000
0
0
4000
Time − µs
50
100
150
200
Time − µs
Figure 16
Figure 15
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
SGLS345 − JUNE 2006
TYPICAL CHARACTERISTICS
STABILITY RANGE
OUTPUT CURRENT
vs
LOAD CAPACITANCE
20
15
VI = 5 V
TA = 25°C
Unstable
I O − Output Current − mA
10
5
0
Stable
−5
−10
−15
−20
10 −6 10 −5 10 −4 10 −3 10 −2 10 −1 10 0
CL− Load Capacitance − mF
Figure 17
10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
10 1
10 2
SGLS345 − JUNE 2006
MACROMODEL INFORMATION
*
*
*
*
TLE2426 OPERATIONAL AMPLIFIER “MACROMODEL” SUBCIRCUIT
CREATED USING PARTS RELEASE 4.03 0N 08/21/90 AT 13:51
REV (N/A)
SUPPLY VOLTAGE: 5 V
CONNECTIONS:
FILTER
| INPUT
*
| | COMMON
*
| | | OUTPUT
*
| | | |
.SUBCKT TLE2426
1 3 4 5
C1
C2
C3
CPSR
DCM +
DCM −
DC
DE
DLP
DLN
DP
ECMR
EGND
EPSR
ENSE
FB
GA
GCM
GPSR
GRC1
GRC2
GRE1
GRE2
HLIM
HCMR
IRP
IEE
IIO
I1
Q1
Q2
R2
RCM
REE
RN1
RN2
RO1
RO2
VCM +
VCM −
VB
VC
VE
VLIM
VLP
VLN
VPSR
RFB
RIN1
RIN2
.MODEL DX
.MODEL QX
.ENDS
11 12 21.66E−12
6 7 30.00E−12
87 0 10.64E−9
85 86 15.9E−9
81 82 DX
83 81 DX
5 53 DX
54 5 DX
90 91 DX
92 90 DX
4 3 DX
84 99 (2,99) 1
99 0 POLY(2)
(3,0) (4,0) 0 .5 .5
85 0 POLY(1)
(3,4) −16.22E − 6 3.24E − 6
89 2 POLY(1)
(88,0) 120E − 6 1
7 99 POLY(6)
VB VC VE VLP VLN VPSR 0 74.8E6 − 10E6 10E6
6 0 11 12 320.4E − 6
0 6 10 99 1.013E − 9
85 86 (85,86)
100E − 6
4 11 (4,11) 3.204E − 4
4 12 (4,12) 3.204E − 4
13 10 (13,10)
1.038E − 3
14 10 (14,10)
1.038E − 3
90 0 VLIM
1K
80 1 POLY(2)
VCM+
VCM − 0 1E2
1E2
3 4 146E − 6
3 10 DC 24.05E − 6
2 0 .2E − 9
88 0 1E − 21
11 89 13 QX
12 80 14 QX
6 9 100.0E3
84 81 1K
10 99 8.316E6
87 0 2.55E8
87 88 11.67E3
8 5 63
7 99 62
82 99 1.0
83 99 − 2.3
9 0 DC 0
3 53 DC 1.400
54 4 DC 1.400
7 8 DC 0
91 0 DC 30
0 92 DC 30
0 86 DC 0
5 2 1K
3 1 220K
1 4 220K
D(IS=800.OE−18)
PNP(IS=800.OE− 18 BF=480)
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
10E6
− 10E6 74E6
11
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
TLE2426MDREP
Package Package Pins
Type Drawing
SOIC
D
8
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
2500
330.0
12.4
Pack Materials-Page 1
6.4
B0
(mm)
K0
(mm)
P1
(mm)
5.2
2.1
8.0
W
Pin1
(mm) Quadrant
12.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TLE2426MDREP
SOIC
D
8
2500
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated