TI V62/03643-01XE

 SGLS127 − JULY 2002
D Controlled Baseline
D
D
D
D
D
D
D
D
D
− One Assembly/Test Site, One Fabrication
Site
Extended Temperature Performance of
−55°C to 125°C
Enhanced Diminishing Manufacturing
Sources (DMS) Support
Enhanced Product Change Notification
Qualification Pedigree†
Push-Pull CMOS Output Drives Capacitive
Loads Without Pullup Resistor,
IO = ± 8 mA
Very Low Power . . . 100 µW Typ at 5 V
Fast Response Time . . . tPLH = 2.7 µs Typ
With 5-mV Overdrive
Single-Supply Operation . . . 4 V to 16 V
On-Chip ESD Protection
D PACKAGE
(TOP VIEW)
1OUT
1IN −
1IN +
GND
1
8
2
7
3
6
4
5
VDD
2OUT
2IN −
2IN +
symbol (each comparator)
IN +
OUT
IN −
† Component qualification in accordance with JEDEC and industry
standards to ensure reliable operation over an extended
temperature range. This includes, but is not limited to, Highly
Accelerated Stress Test (HAST) or biased 85/85, temperature
cycle, autoclave or unbiased HAST, electromigration, bond
intermetallic life, and mold compound life. Such qualification
testing should not be viewed as justifying use of this component
beyond specified performance and environmental limits.
description
The TLC3702 consists of two independent micropower voltage comparators designed to operate from a single
supply and be compatible with modern HCMOS logic systems. They are functionally similar to the LM339 but
use one-twentieth of the power for similar response times. The push-pull CMOS output stage drives capacitive
loads directly without a power-consuming pullup resistor to achieve the stated response time. Eliminating the
pullup resistor not only reduces power dissipation, but also saves board space and component cost. The output
stage is also fully compatible with TTL requirements.
Texas Instruments LinCMOS process offers superior analog performance to standard CMOS processes.
Along with the standard CMOS advantages of low power without sacrificing speed, high input impedance, and
low bias currents, the LinCMOS process offers extremely stable input offset voltages with large differential
input voltages. This characteristic makes it possible to build reliable CMOS comparators.
ORDERING INFORMATION
TA
PACKAGE‡
ORDERABLE
PART NUMBER
TOP-SIDE
MARKING
−55°C to 125°C
SOP − D
Tape and reel
TLC3702MDREP
3702ME
‡ Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines
are available at www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
LinCMOS is a trademark of Texas Instruments Incorporated.
Copyright  2002, Texas Instruments Incorporated
! "#$ ! %#&'" ($)
(#"! " !%$""! %$ *$ $! $+! !#$!
!(( ,-) (#" %"$!!. ($! $"$!!'- "'#($
$!. '' %$$!)
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
 SGLS127 − JULY 2002
functional block diagram (each comparator)
VDD
IN+
Differential
Input
Circuits
OUT
IN−
GND
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 18 V
Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±18 V
Input voltage range, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to VDD
Output voltage range, VO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . − 0.3 V to VDD
Input current, II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±5 mA
Output current, IO (each output) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA
Total supply current into VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 mA
Total current out of GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 mA
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature range, TA
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −55°C to 125°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential voltages, are with respect to network ground.
2. Differential voltages are at IN+ with respect to IN −.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
TA = 125°C
POWER RATING
D
725 mW
5.8 mW/°C
464 mW
377 mW
145 mW
recommended operating conditions
MIN
NOM
MAX
Supply voltage, VDD
4
5
16
V
Common-mode input voltage, VIC
0
V
High-level output current, IOH
VDD − 1.5
−20
mA
Low-level output current, IOL
20
mA
125
°C
Operating free-air temperature, TA
2
−55
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
UNIT
 SGLS127 − JULY 2002
electrical characteristics at specified operating free-air temperature, VDD = 5 V (unless otherwise
noted)
PARAMETER
TEST CONDITIONS†
TA
−55°C to 125°C
VIO
Input offset voltage
VDD = 5 V to 10 V,
VIC = VICRmin, See Note 3
IIO
Input offset current
VIC = 2.5 V
MIN
25°C
1.2
125°C
VIC = 2.5 V
VICR
Common-mode input voltage range
−55°C to 125°C
CMRR
kSVR
Common-mode rejection ratio
Supply-voltage rejection ratio
VIC = VICRmin
VDD = 5 V to 10 V
15
0 to
VDD − 1
25°C
84
83
−55°C
82
25°C
85
125°C
85
4.5
4.2
VID = 1 V,
IOH = − 4 mA
125°C
VOL
Low-level output voltage
VID = −1 V,
IOH = − 4 mA
125°C
IDD
Supply current (both comparators)
Outputs low,
No load
25°C
25°C
nA
dB
dB
82
25°C
High-level output voltage
nA
V
0 to
VDD − 1.5
125°C
VOH
mV
pA
30
− 55°C
UNIT
pA
5
125°C
25°C
5
1
25°C
Input bias current
MAX
10
25°C
IIB
TYP
4.7
V
210
300
500
18
−55°C to 125°C
40
90
mV
µA
† All characteristics are measured with zero common-mode voltage unless otherwise noted.
NOTE 3. The offset voltage limits given are the maximum values required to drive the output up to 4.5 V or down to 0.3 V.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
 SGLS127 − JULY 2002
switching characteristics, VDD = 5 V, TA = 25°C
PARAMETER
tPLH
tPHL
TEST CONDITIONS
Propagation delay time, low-to-high-level output†
Propagation delay time, high-to-low-level output†
tf
Fall time
tr
Rise time
f = 10 kHz,
CL = 50 pF
TYP
Overdrive = 2 mV
4.5
Overdrive = 5 mV
2.7
Overdrive = 10 mV
1.9
Overdrive = 20 mV
1.4
Overdrive = 40 mV
1.1
VI = 1.4 V step at IN+
Overdrive = 2 mV
1.1
Overdrive = 5 mV
2.3
Overdrive = 10 mV
1.5
Overdrive = 20 mV
0.95
Overdrive = 40 mV
0.65
VI = 1.4 V step at IN+
f = 10 kHz,
Overdrive = 50 mV
CL = 50 pF
0.15
f = 10 kHz,
CL = 50 pF
f = 10 kHz,
CL = 50 pF
Overdrive = 50 mV
† Simultaneous switching of inputs causes degradation in output response.
4
MIN
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MAX
UNIT
µs
4
µs
50
ns
125
ns
 SGLS127 − JULY 2002
PRINCIPLES OF OPERATION
LinCMOS process
The LinCMOS process is a linear polysilicon-gate CMOS process. Primarily designed for single-supply
applications, LinCMOS products facilitate the design of a wide range of high-performance analog functions
from operational amplifiers to complex mixed-mode converters.
While digital designers are experienced with CMOS, MOS technologies are relatively new for analog designers.
This short guide is intended to answer the most frequently asked questions related to the quality and reliability
of LinCMOS products. Further questions should be directed to the nearest TI field sales office.
electrostatic discharge
CMOS circuits are prone to gate oxide breakdown when exposed to high voltages even if the exposure is only
for very short periods of time. Electrostatic discharge (ESD) is one of the most common causes of damage to
CMOS devices. It can occur when a device is handled without proper consideration for environmental
electrostatic charges, e.g., during board assembly. If a circuit in which one amplifier from a dual op amp is being
used and the unused pins are left open, high voltages tend to develop. If there is no provision for ESD protection,
these voltages may eventually punch through the gate oxide and cause the device to fail. To prevent voltage
buildup, each pin is protected by internal circuitry.
Standard ESD-protection circuits safely shunt the ESD current by providing a mechanism whereby one or more
transistors break down at voltages higher than the normal operating voltages but lower than the breakdown
voltage of the input gate. This type of protection scheme is limited by leakage currents which flow through the
shunting transistors during normal operation after an ESD voltage has occurred. Although these currents are
small, on the order of tens of nanoamps, CMOS amplifiers are often specified to draw input currents as low as
tens of picoamps.
To overcome this limitation, TI design engineers developed the patented ESD-protection circuit shown in
Figure 1. This circuit can withstand several successive 2-kV ESD pulses, while reducing or eliminating leakage
currents that may be drawn through the input pins. A more detailed discussion of the operation of the TI
ESD-protection circuit is presented on the next page.
All input and output pins on LinCMOS and Advanced LinCMOS products have associated ESD-protection
circuitry that undergoes qualification testing to withstand 2000 V discharged from a 100-pF capacitor through
a 1500-Ω resistor (human body model) and 200 V from a 100-pF capacitor with no current-limiting resistor
(charged device model). These tests simulate both operator and machine handling of devices during normal
test and assembly operations.
VDD
R1
Input
To Protect Circuit
R2
Q1
Q2
D1
D2
D3
GND
Figure 1. LinCMOS ESD-Protection Schematic
LinCMOS and Advanced LinCMOS are trademarks of Texas Instruments Incorporated.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
 SGLS127 − JULY 2002
PRINCIPLES OF OPERATION
input protection circuit operation
Texas Instruments patented protection circuitry allows for both positive- and negative-going ESD transients.
These transients are characterized by extremely fast rise times and usually low energies, and can occur both
when the device has all pins open and when it is installed in a circuit.
positive ESD transients
Initial positive charged energy is shunted through Q1 to VSS. Q1 turns on when the voltage at the input rises
above the voltage on the VDD pin by a value equal to the VBE of Q1. The base current increases through R2
with input current as Q1 saturates. The base current through R2 forces the voltage at the drain and gate of Q2
to exceed its threshold level (VT ∼ 22 to 26 V) and turn Q2 on. The shunted input current through Q1 to VSS is
now shunted through the n-channel enhancement-type MOSFET Q2 to VSS. If the voltage on the input pin
continues to rise, the breakdown voltage of the zener diode D3 is exceeded and all remaining energy is
dissipated in R1 and D3. The breakdown voltage of D3 is designed to be 24 V to 27 V, which is well below the
gate-oxide voltage of the circuit to be protected.
negative ESD transients
The negative charged ESD transients are shunted directly through D1. Additional energy is dissipated in R1
and D2 as D2 becomes forward biased. The voltage seen by the protected circuit is −0.3 V to −1 V (the forward
voltage of D1 and D2).
circuit-design considerations
LinCMOS products are being used in actual circuit environments that have input voltages that exceed the
recommended common-mode input voltage range and activate the input protection circuit. Even under normal
operation, these conditions occur during circuit power up or power down, and in many cases, when the device
is being used for a signal conditioning function. The input voltages can exceed VICR and not damage the device
only if the inputs are current limited. The recommended current limit shown on most product data sheets is
±5 mA. Figure 2 and Figure 3 show typical characteristics for input voltage versus input current.
Normal operation and correct output state can be expected even when the input voltage exceeds the positive
supply voltage. Again, the input current should be externally limited even though internal positive current limiting
is achieved in the input protection circuit by the action of Q1. When Q1 is on, it saturates and limits the current
to approximately 5-mA collector current by design. When saturated, Q1 base current increases with input
current. This base current is forced into the VDD pin and into the device IDD or the VDD supply through R2
producing the current limiting effects shown in Figure 2. This internal limiting lasts only as long as the input
voltage is below the VT of Q2.
When the input voltage exceeds the negative supply voltage, normal operation is affected and output voltage
states may not be correct. Also, the isolation between channels of multiple devices (duals and quads) can be
severely affected. External current limiting must be used since this current is directly shunted by D1 and D2 and
no internal limiting is achieved. If normal output voltage states are required, an external input voltage clamp is
required (see Figure 4).
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
 SGLS127 − JULY 2002
PRINCIPLES OF OPERATION
circuit-design considerations (continued)
INPUT CURRENT
vs
INPUT VOLTAGE
INPUT CURRENT
vs
INPUT VOLTAGE
8
10
TA = 25° C
TA = 25° C
9
7
8
I I − Input Current − mA
I I − Input Current − mA
6
5
4
3
2
7
6
5
4
3
2
1
1
0
VDD
VDD + 4
VDD + 8
VDD + 12
0
VDD − 0.3
VDD − 0.5
VDD − 0.7
VDD − 0.9
VI − Input Voltage − V
VI − Input Voltage − V
Figure 3
Figure 2
VDD
RI
VI
+
Positive Voltage Input Current Limit :
1/2
TLC3702
Vref
−
See Note A
RI +
V I * V DD * 0.3 V
5 mA
Negative Voltage Input Current Limit :
* V I * V DD * (* 0.3 V)
RI +
5 mA
NOTE A: If the correct input state is required when the negative input exceeds GND, a Schottky clamp is required.
Figure 4. Typical Input Current-Limiting Configuration for a LinCMOS Comparator
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
 SGLS127 − JULY 2002
PARAMETER MEASUREMENT INFORMATION
The TLC3702 contains a digital output stage which, if held in the linear region of the transfer curve, can cause
damage to the device. Conventional operational amplifier/comparator testing incorporates the use of a servo
loop which is designed to force the device output to a level within this linear region. Since the servo-loop method
of testing cannot be used, we offer the following alternatives for measuring parameters such as input offset
voltage, common-mode rejection, etc.
To verify that the input offset voltage falls within the limits specified, the limit value is applied to the input as shown
in Figure 5(a). With the noninverting input positive with respect to the inverting input, the output should be high.
With the input polarity reversed, the output should be low.
A similar test can be made to verify the input offset voltage at the common-mode extremes. The supply voltages
can be slewed to provide greater accuracy, as shown in Figure 5(b) for the VICR test. This slewing is done instead
of changing the input voltages.
A close approximation of the input offset voltage can be obtained by using a binary search method to vary the
differential input voltage while monitoring the output state. When the applied input voltage differential is equal,
but opposite in polarity, to the input offset voltage, the output changes states.
Figure 6 illustrates a practical circuit for direct dc measurement of input offset voltage that does not bias the
comparator in the linear region. The circuit consists of a switching mode servo loop in which IC1a generates
a triangular waveform of approximately 20-mV amplitude. IC1b acts as a buffer, with C2 and R4 removing any
residual dc offset. The signal is then applied to the inverting input of the comparator under test, while the
noninverting input is driven by the output of the integrator formed by IC1c through the voltage divider formed
by R8 and R9. The loop reaches a stable operating point when the output of the comparator under test has a
duty cycle of exactly 50%, which can only occur when the incoming triangle wave is sliced symmetrically or when
the voltage at the noninverting input exactly equals the input offset voltage.
Voltage dividers R8 and R9 provide an increase in input offset voltage by a factor of 100 to make measurement
easier. The values of R5, R7, R8, and R9 can significantly influence the accuracy of the reading; therefore, it
is suggested that their tolerance level be one percent or lower.
Measuring the extremely low values of input current requires isolation from all other sources of leakage current
and compensation for the leakage of the test socket and board. With a good picoammeter, the socket and board
leakage can be measured with no device in the socket. Subsequently, this open socket leakage value can be
subtracted from the measurement obtained with a device in the socket to obtain the actual input current of the
device.
5V
1V
+
Applied VIO
Limit
+
−
VO
−
Applied VIO
Limit
VO
−4V
(a) VIO WITH VIC = 0 V
(b) VIO WITH VIC = 4 V
Figure 5. Method for Verifying That Input Offset Voltage Is Within Specified Limits
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
 SGLS127 − JULY 2002
PARAMETER MEASUREMENT INFORMATION
VDD
IC1a
1/4 TLC274CN
+
Buffer
C2
1 µF
R6
1 MΩ
−
R4
47 kΩ
−
VIO
(X100)
+
IC1b
1/4 TLC274CN
Integrator
C4
0.1 µF
−
Triangle
Generator
R9
100 Ω 1%
R3
100 Ω
+
R7
1.8 kΩ 1%
R1
240 kΩ
+
IC1c
1/4 TLC274CN
DUT
−
C1
0.1 µF
C3
0.68 µF
R5
1.8 kΩ 1%
R8
10 kΩ 1%
R2
10 kΩ
Figure 6. Circuit for Input Offset Voltage Measurement
Response time is defined as the interval between the application of an input step function and the instant when
the output reaches 50% of its maximum value. Response time for the low-to-high-level output is measured from
the leading edge of the input pulse, while response time for the high-to-low-level output is measured from the
trailing edge of the input pulse. Response time measurement at low input signal levels can be greatly affected
by the input offset voltage. The offset voltage should be balanced by the adjustment at the inverting input as
shown in Figure 7, so that the circuit is just at the transition point. A low signal, for example 105-mV or 5-mV
overdrive, causes the output to change state.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
 SGLS127 − JULY 2002
PARAMETER MEASUREMENT INFORMATION
VDD
Pulse
Generator
1 µF
50 Ω
+
1V
DUT
10 Ω
10-Turn
Potentiometer
−
1 kΩ
CL
(see Note A)
0.1 µF
−1V
TEST CIRCUIT
Overdrive
Overdrive
Input
Input
100 mV
100 mV
90%
Low-to-High
Level Output
90%
High-to-Low
Level Output
50%
10%
50%
10%
tf
tr
tPHL
tPLH
VOLTAGE WAVEFORMS
NOTE A: CL includes probe and jig capacitance.
Figure 7. Response, Rise, and Fall Times Circuit and Voltage Waveforms
10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
 SGLS127 − JULY 2002
TYPICAL CHARACTERISTICS†
Table of Graphs
FIGURE
VIO
IIB
Input offset voltage
Distribution
8
Input bias current
vs Free-air temperature
9
CMRR
Common-mode rejection ratio
vs Free-air temperature
10
kSVR
Supply-voltage rejection ratio
vs Free-air temperature
11
VOH
High-level output current
vs Free-air temperature
vs High-level output current
12
13
VOL
Low-level output voltage
vs Low-level output current
vs Free-air temperature
14
15
tt
Transition time
vs Load capacitance
16
Supply current response
vs Time
17
Low-to-high-level output response
Low-to-high level output propagation delay time
18
High-to-low level output response
High-to-low level output propagation delay time
19
Low-to-high level output propagation delay time
vs Supply voltage
20
High-to-low level output propagation delay time
vs Supply voltage
21
Supply current
vs Frequency
vs Supply voltage
vs Free-air temperature
22
23
24
tPLH
tPHL
IDD
INPUT BIAS CURRENT
vs
FREE-AIR TEMPERATURE
DISTRIBUTION OF INPUT
OFFSET VOLTAGE
180
Number of Units
160
140
120
100
80
60
40
20
ÉÉ
ÉÉ
ÉÉÇ
ÉÉÇ
ÉÉÇ
ÉÉÇ
ÉÉÇ
Ç
ÉÉÇ
Ç
Ç
Ç
ÇÇÉÉÉ
ÉÉ
ÉÉÉÉ
ÇÇÉÇ
ÇÉ
ÉÉÇ
Ç
ÇÇÉÇ
ÉÉ
Ç
É
ÇÇÉ
ÇÇ
ÉÉÉÉ
ÇÇÉ
ÇÇÉÇ
ÇÇÇÇ
ÇÇÇÇ
ÉÉ
ÉÉ
0
−5
10
VDD = 5 V
VIC = 2.5 V
TA = 25° C
698 Units Tested
From 4 Wafer Lots
−4
−3
−2
−1
0
1
2
3
4
VDD = 5 V
VIC = 2.5 V
IIB − Input Bias Current − nA
200
1
0.1
0.01
0.001
5
25
50
75
100
125
TA − Free-Air Temperature − °C
VIO − Input Offset Voltage − mV
Figure 9
Figure 8
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
 SGLS127 − JULY 2002
TYPICAL CHARACTERISTICS†
SUPPLY VOLTAGE REJECTION RATIO
vs
FREE-AIR TEMPERATURE
90
90
88
k SVR − Supply Voltage Rejection Ratio − dB
CMRR − Common-Mode Rejection Ratio − dB
COMMON-MODE REJECTION RATIO
vs
FREE-AIR TEMPERATURE
VDD = 5 V
86
84
82
80
78
76
74
72
70
−75
−50
−25
0
25
50
75
100
88
VDD = 5 V to 10 V
86
84
82
80
78
76
74
72
70
−75
125
−50
−25
TA − Free-Air Temperature − °C
50
75
100
5
VDD
VOH − High-Input Level Output Voltage −V
VDD = 5 V
IOH = − 4 mA
4.9
4.85
4.8
4.75
4.7
4.65
4.6
4.55
4.5
−75 −50
VDD = 16 V
−0.25
−0.5
−0.75
10 V
−1
5V
−1.25
4V
−1.5
−1.75
3V
TA = 25° C
−2
−25
0
25
50
75
100
125
0
−2.5
TA − Free-Air Temperature − °C
−5
−7.5
−10 −12.5 −15 −17.5 −20
IOH − High-Level Output Current − mA
Figure 12
Figure 13
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
12
125
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
HIGH-LEVEL OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
VOH − High-Level Outout Voltage − V
25
Figure 11
Figure 10
4.95
0
TA − Free-Air Temperature − °C
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
 SGLS127 − JULY 2002
TYPICAL CHARACTERISTICS†
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
LOW-LEVEL OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
1.5
400
3V
VOL − Low-Level Output Voltage − mV
VOL − Low-Level Output Voltage − V
TA = 25°C
4V
1.25
5V
1
0.75
10 V
0.5
0.25
VDD = 16 V
0
0
2
4
6
8
10
12
14
16
18
350
300
250
200
150
100
50
0
−75
20
VDD = 5 V
IOL = 4 mA
−50
IOL − Low-Level Output Current − mA
−25
0
25
50
75
100
125
TA − Free-Air Temperature − °C
Figure 15
Figure 14
OUTPUT TRANSITION TIME
vs
LOAD CAPACITANCE
SUPPLY CURRENT RESPONSE
TO AN OUTPUT VOLTAGE TRANSITION
250
225
VDD = 5 V
TA = 25°C
10
IDD − Supply
Current − mA
175
Rise Time
150
125
Fall Time
5
0
100
Output
Voltage − V
t t − Transition Time − ns
200
VDD = 5 V
CL = 50 pF
f = 10 kHz
75
50
25
0
0
200
400
600
800
5
0
1000
t − Time
CL − Load Capacitance − pF
Figure 17
Figure 16
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
 SGLS127 − JULY 2002
TYPICAL CHARACTERISTICS
LOW-TO-HIGH-LEVEL OUTPUT RESPONSE
FOR VARIOUS INPUT OVERDRIVES
5
5
VO − Output
Voltage − V
40 mV
20 mV
10 mV
5 mV
2 mV
VO − Output
Voltage − V
40 mV
20 mV
10 mV
5 mV
2 mV
0
0
100
100
Differential
Input
Voltage − mV
Differential
Input
Voltage − mV
HIGH-TO-LOW-LEVEL OUTPUT RESPONSE
FOR VARIOUS INPUT OVERDRIVES
VDD = 5 V
TA = 25°C
CL = 50 pF
0
0
1
2
3
4
VDD = 5 V
TA = 25° C
CL = 50 pF
0
5
0
tPLH − Low-to-High-Level Output
Response Time − µs
1
Figure 18
Overdrive = 2 mV
4
5 mV
3
10 mV
2
20 mV
40 mV
0
2
4
6
8
10
12
14
16
t PHL − High-to-Low-Level Output Response − µs
t PLH − Low-to-High-Level Output Response − µs
CL = 50 pF
TA = 25°C
0
5
6
CL = 50 pF
TA = 25°C
5
Overdrive = 2 mV
4
3
5 mV
2
10 mV
20 mV
1
40 mV
0
0
2
VDD − Supply Voltage − V
4
6
8
Figure 21
POST OFFICE BOX 655303
10
12
VDD − Supply Voltage − V
Figure 20
14
4
HIGH-TO-LOW-LEVEL
OUTPUT RESPONSE TIME
vs
SUPPLY VOLTAGE
6
1
3
Figure 19
LOW-TO-HIGH-LEVEL
OUTPUT RESPONSE TIME
vs
SUPPLY VOLTAGE
5
2
tPHL − High-to-Low-Level Output
Response Time − µs
• DALLAS, TEXAS 75265
14
16
 SGLS127 − JULY 2002
TYPICAL CHARACTERISTICS†
AVERAGE SUPPLY CURRENT
(PER COMPARATOR)
vs
FREQUENCY
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
40
10000
Outputs Low
No Loads
35
VDD = 16 V
1000
VDD − Supply Current − µ A
VDD − Supply Current − µ A
TA = 25°C
CL = 50 pF
10 V
5V
100
4V
TA = − 55°C
TA = − 40°C
30
25
TA = − 25°C
20
15
TA = − 125°C
TA = 85°C
10
5
3V
10
0.01
0
0.1
1
10
100
0
1
f − Frequency − kHz
2
3
4
5
6
7
8
VDD − Supply Voltage − V
Figure 23
Figure 22
SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
30
VDD = 5 V
No Load
IDD − Supply Current −µA
25
20
Outputs Low
15
10
Outputs High
5
0
−75
−50
−25
0
25
50
75
100
125
TA − Free-Air Temperature − °C
Figure 24
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
15
 SGLS127 − JULY 2002
APPLICATION INFORMATION
The inputs should always remain within the supply rails in order to avoid forward biasing the diodes in the
electrostatic discharge (ESD) protection structure. If either input exceeds this range, the device is not damaged
as long as the input is limited to less than 5 mA. To maintain the expected output state, the inputs must remain
within the common-mode range. For example, at 25°C with VDD = 5 V, both inputs must remain between
−0.2 V and 4 V to ensure proper device operation.
To ensure reliable operation, the supply should be decoupled with a capacitor (0.1 µF) that is positioned as close
to the device as possible.
The TLC3702 has internal ESD-protection circuits that prevent functional failures at voltages up to 2000 V as
tested under MIL-STD-883C, Method 3015.2; however, care should be exercised in handling these devices as
exposure to ESD may result in the degradation of the device parametric performance.
Table of Applications
FIGURE
Pulse-width-modulated motor speed controller
25
Enhanced supply supervisor
26
Two-phase nonoverlapping clock generator
27
Micropower switching regulator
28
12 V
SN75603
Half-H Driver
DIR
5V
EN
1/2 TLC3702
See
Note A
+
100 kΩ
+
10 kΩ
5V
−
10 kΩ
C1
0.01 µF
(see Note B)
Motor
−
1/2 TLC3704
12 V
DIR
10 kΩ
5V
EN
10 kΩ
Motor Speed Control
Potentiometer
5V
Direction
Control
S1
SPDT
NOTES: A. The recommended minimum capacitance is 10 µF to eliminate common ground switching noise.
B. Adjust C1 for change in oscillator frequency.
Figure 25. Pulse-Width-Modulated Motor Speed Controller
16
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN75604
Half-H Driver
 SGLS127 − JULY 2002
APPLICATION INFORMATION
5V
VCC
12 V
12-V
Sense
3.3 kΩ
SENSE
10 kΩ
1/2 TLC3702
+
TL7705A
RESIN
1 kΩ
5V
RESET
To µP
Reset
−
REF
CT
GND
2.5 V
1 µF
CT
(see Note B)
1/2 TLC3702
+
V(UNREG)
(see Note A)
To µP Interrupt
Early Power Fail
R1
−
R2
Monitors 5 VDC Rail
Monitors 12 VDC Rail
Early Power Fail Warning
(R1 +R2)
R2
B. The value of CT determines the time delay of reset.
NOTES: A.
V (UNREG) + 2.5
Figure 26. Enhanced Supply Supervisor
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
17
 SGLS127 − JULY 2002
APPLICATION INFORMATION
12 V
12 V
R1
100 kΩ
(see Note B)
12 V
−
−
R2
5 kΩ
(see Note C)
1/2 TLC3702
100 kΩ
1OUT
+
+
22 kΩ
100 kΩ
−
C1
0.01 µF
(see Note A)
100 kΩ
R3
100 kΩ
(see Note B)
1OUT
2OUT
NOTES: A. Adjust C1 for a change in oscillator frequency where:
1/f = 1.85(100 kΩ)C1
B. Adjust R1 and R3 to change duty cycle
C. Adjust R2 to change deadtime
Figure 27. Two-Phase Nonoverlapping Clock Generator
POST OFFICE BOX 655303
1/2 TLC3702
2OUT
+
12 V
18
1/2 TLC3702
• DALLAS, TEXAS 75265
 SGLS127 − JULY 2002
APPLICATION INFORMATION
V + 6 V to 16 V
I
I + 0.01 mA to 0.25 mA
L
(R1 ) R2)
V + 2.5
O
R2
1/2 TLC3702
+
SK9504
(see Note C)
G S
100 kΩ
−
100 kΩ
VI
VI
1/2 TLC3702
+
−
100 kΩ
D
+
C1
180 µF
(see Note A)
VI
47 µF
Tantalum
IN5818
100 kΩ
R1
R=6Ω
L = 1 mH
(see Note D)
VO
100 kΩ
TLC271
(see Note B)
VI
470 µF
RL
+
R2
100 kΩ
−
C2
100 pF
100 kΩ
270 kΩ
VI
LM385
2.5 V
NOTES: A. Adjust C1 for a change in oscillator frequency
B. TLC271 − Tie pin 8 to pin 7 for low bias operation
C. SK9504 − VDS = 40 V
IDS = 1 A
D. To achieve microampere current drive, the inductance of the circuit must be increased.
Figure 28. Micropower Switching Regulator
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
19
 SGLS127 − JULY 2002
MECHANICAL DATA
D (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PIN SHOWN
0.050 (1,27)
0.020 (0,51)
0.014 (0,35)
14
0.010 (0,25) M
8
0.008 (0,20) NOM
0.244 (6,20)
0.228 (5,80)
0.157 (4,00)
0.150 (3,81)
Gage Plane
0.010 (0,25)
1
7
0°−ā 8°
A
0.044 (1,12)
0.016 (0,40)
Seating Plane
0.069 (1,75) MAX
0.010 (0,25)
0.004 (0,10)
PINS **
0.004 (0,10)
8
14
16
A MAX
0.197
(5,00)
0.344
(8,75)
0.394
(10,00)
A MIN
0.189
(4,80)
0.337
(8,55)
0.386
(9,80)
DIM
4040047 / D 10/96
NOTES: A.
B.
C.
D.
20
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15).
Falls within JEDEC MS-012
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
18-Sep-2008
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TLC3702MDREP
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
V62/03643-01XE
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TLC3702-EP :
TLC3702
• Catalog:
TLC3702-Q1
• Automotive:
• Military: TLC3702M
NOTE: Qualified Version Definitions:
- TI's standard catalog product
• Catalog
- Q100 devices qualified for high-reliability automotive applications targeting zero defects
• Automotive
• Military - QML certified for Military and Defense Applications
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Jul-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
TLC3702MDREP
Package Package Pins
Type Drawing
SOIC
D
8
SPQ
Reel
Reel
Diameter Width
(mm) W1 (mm)
2500
330.0
12.4
Pack Materials-Page 1
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
6.4
5.2
2.1
8.0
W
Pin1
(mm) Quadrant
12.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Jul-2008
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TLC3702MDREP
SOIC
D
8
2500
346.0
346.0
29.0
Pack Materials-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
18-Sep-2008
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TLC3702MDREP
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
V62/03643-01XE
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TLC3702-EP :
TLC3702
• Catalog:
TLC3702-Q1
• Automotive:
• Military: TLC3702M
NOTE: Qualified Version Definitions:
- TI's standard catalog product
• Catalog
- Q100 devices qualified for high-reliability automotive applications targeting zero defects
• Automotive
• Military - QML certified for Military and Defense Applications
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
TLC3702MDREP
Package Package Pins
Type Drawing
SOIC
D
8
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
2500
330.0
12.4
Pack Materials-Page 1
6.4
B0
(mm)
K0
(mm)
P1
(mm)
5.2
2.1
8.0
W
Pin1
(mm) Quadrant
12.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TLC3702MDREP
SOIC
D
8
2500
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated