Ordering number : ENA2189 LC898111AXA LC898111AXB http://onsemi.com CMOS LSI OIS Controller & Driver Overview The LC898111AXA and the LC898111AXB are image stabilization system control LSIs for smartphone camera modules. The LSIs have built-in digital signal processing circuits, such as a 2ch saturation H-Bridge Driver and a Flexible Filter circuit, and control VCM type actuators. The LC898111AXA and the LC898111AXB are identical LSIs except for the dimensions, i.e. XA has WLP thickness, max. 0.33 mm without back coat (B/C) and XB has WLP thickness, max. 0.69 mm with B/C. Function Digital signal processing LSI (Logic LSI) Built-in digital servo circuit Built-in Gyro filter AD converter 12-bit input 5ch Equipped with a sample-hold circuit DA converter 8-bit Output 2ch (Constant current Bias : max 7mA) Built-in Serial I/F circuit (2-wire I2C-Bus or 4-wire SPI Bus interface) Built-in Hall Bias circuit Built-in Hall Amp (Gain of Opamp : x25, x50, x75, x100, x150, x200) Built-in OSC (Oscillator) 48MHz 5% (Frequency adjustment function) External Clock input is possible from TSTCLK (48MHz 5%) Built-in LDO (Low Drop-Out regulator) Digital Gyro I/F for the companies (SPI Bus) (Please refer for the details) Support Hall sensor and Photo Reflector as means to detect a position Motor Driver Saturation-drive H bridge x2ch IO max : 220mA WLP48J Package LC898111AXA : WLP48J (2.57mm x 3.22mm, thickness max 0.33mm, without B/C) LC898111AXB : WLP48 (2.57mm x 3.22mm, thickness max 0.69mm, with B/C) Pb-free Halogen Free Power supply voltage Logic : DVDD30 = 2.6 to 3.6 V Driver : VM = 2.6 to 3.6 V 2 * I C Bus is a trademark of Philips Corporation. Semiconductor Components Industries, LLC, 2013 May, 2013 Ver.3.5b WLP48 ORDERING INFORMATION See detailed ordering and shipping information on page 7 of this data sheet. 529HK 20121127-S00003,20130219-S00001 No.A2189-1/7 LC898111AXA, LC898111AXB Block Diagram Figure 3.1 Example of wiring diagram (Hall) in LC898111AXA/XB No.A2189-2/7 LC898111AXA, LC898111AXB LC898111AXA PACKAGE DIMENSIONS WLP48J(3.22X2.57) No.A2189-3/7 LC898111AXA, LC898111AXB LC898111AXB PACKAGE DIMENSIONS WLP48(3.22X2.57) No.A2189-4/7 LC898111AXA, LC898111AXB Pin Assign (WLP48J/WLP48) Top View 1 OPTESTO OPINPY ADVDD ADVSS GYYI HXI 2 HLXBO OPINMY ADVRH GYXI DVSS I2CDT 3 EPSOIF DAOPVDD ADVRL HYI EPCSBIF2 I2CCK 4 DVDD30 DAOPVSS OPINPX SAD4 SSB MISO 5 BUSY2 HLYBO OPINMX ZRESET LDOPO DVDD30 6 BUSY1 TEST DVSS TSTCLK LDSTBB DGSCLK 7 VM MON CLKSEL DGMOSI DGMISO DGINT 8 OUT4 OUT3 OUT2 OUT1 PGND DGSSB F E D C B A Driver DAC OpAmp ADC EEPROM i/f Logic GND IO VDD (2.6V to 3.6V) Logic Core VDD (1.14 to 1.26V) No.A2189-5/7 LC898111AXA, LC898111AXB typ I : INPUT, O : OUTPUT, B : BIDIRECTION, P : Power, GND Ball Pin Name type F8 OUT4 O Driver Output F7 VM P Driver VDD (2.6V to 3.6V) F6 BUSY1 B F5 BUSY2 B BUSY2(O) / General-purpose IOPORT(B) / inner signal Monitor(O) F4 DVDD30 P Logic IO VDD (2.6V to 3.6V) F3 EPSOIF I EEPROM I/F F2 HLXBO O Hall-X Bias (Current Drive) No Description 2 EEPROM I/F (at I C type EEPROM ) / BUSY1(O) / General-purpose IOPORT(B) / inner signal Monitor(O) F1 OPTESTO O OpAmp Test out E8 OUT3 O Driver output E7 MON B inner signal monitor / General-purpose IOPORT E6 TEST I SPI & External clock case sets “1” other cases set “0” E5 HLYBO O Hall-Y Bias (Current Drive) E4 DAOPVSS P DA&Opamp VSS E3 DAOPVDD P DA&Opamp VDD (2.6V to 3.6V) E2 OPINMY I Hall-Y OpAmp input E1 OPINPY I Hall-Y OpAmp input+ D8 OUT2 O Driver Output D7 CLKSEL I change pin of OSC(0) and External clock(1) D6 DVSS P Logic GND D5 OPINMX I Hall-X OpAmp input D4 OPINPX I Hall-X OpAmp input+ D3 ADVRL I ADC Reference Voltage Low input D2 ADVRH I ADC Reference Voltage High input D1 ADVDD P AD VDD (2.6V to 3.6V) C8 OUT1 O Driver Output C7 DGMOSI B Digital Gyro (4-wire)IF data(O) / HPS Control(O) / General-purpose IOPORT(B) C6 TSTCLK I CLKSEL=1 : External Clock, CLKSEL=0 : change pin of I C(0) and SPI(1) C5 ZRESET I Hard Wafer Reset C4 SAD4 I General-purpose AD input C3 HYI I Hall-Y AD input C2 GYXI I Gyro-X AD input C1 ADVSS P AD GND B8 PGND P Driver GND B7 DGMISO B Digital Gyro SPI IF Data( I ) / Digital Gyro I C IF Data(B) B6 LDSTBB I LDO Standby (0 : Standby On, 1 : Standby Off) B5 LDOPO P LDO Power supply out (Logic Core VDD (1.14V to 1.26V)) B4 SSB I SPI I/F Chip Select / VDD fix at I C i/f B3 EPCSBIF2 B EEPROM I/F B2 DVSS P Logic GND B1 GYYI I Gyro-Y AD input A8 DGSSB B DGINT B A6 DGSCLK B A5 DVDD30 P Logic IO VDD (2.6V to 3.6V) and power supply to LDO A4 MISO O SPI I/F Data / General-purpose IOPORT / inner signal monitor A3 I2CCK I I C_IF clock / SPI IF clock A2 I2CDT B I C_IF Data(B) / SPI IF Data A1 HXI I Hall-X AD input A7 2 2 2 Digital Gyro SPI IF Chip Select(O) / inner signal monitor(O) / General-purpose IOPORT(B) Digital Gyro SPI IF Data Busy( I ) / inner signal monitor(O) / General-purpose IOPORT(B) 2 Digital Gyro SPI IF clock (O) / Digital Gyro I C IF clock(O) / HPS Control 1(O) / General-purpose IOPORT (B) 2 2 No.A2189-6/7 LC898111AXA, LC898111AXB ORDERING INFORMATION Device LC898111AXA-MH Package WLP48J(3.22X2.57) (Pb-Free / Halogen Free) LC898111AXB-MH WLP48(3.22X2.57) (Pb-Free / Halogen Free) Shipping (Qty / Packing) 5000 / Tape & Reel 5000 / Tape & Reel ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PS No.A2189-7/7