[AK4115] AK4115 High Feature 192kHz 24bit Digital Audio Interface Transceiver GENERAL DESCRIPTION The AK4115 is a 24-bit stereo digital audio transceiver that supports sampling rates up to 216kHz. The channel status bit decoder supports both consumer and professional modes and can automatically detect Non-PCM bit streams such as Dolby Digital or MPEG. The AK4115 supports a wide array of features a couple of them being; differential cable driver and receiver support, and an internal PLL that can support clock sources such as bi-phase and “word clock”. Control of AK4115 is achieved though a μP or pin-strapping (parallel mode) and it is packaged in a space- saving 64pin-LQFP. * Dolby Digital is a trademark of Dolby Laboratories. FEATURES AES3, IEC60958, S/PDIF, EIAJ CP1201 Compatible Very Low Jitter Analog PLL Synchronous / Asynchronous Mode Include Two X’tal Oscillators Clock Source: PLL or External Clock - Reference Clock for PLL: • Biphase signal: 22kHz to 216kHz • External Clock (ELRCK pin): 22kHz to 216kHz 8-channel Receiver input - One channel supports Differential Input 2-channel Transmission output (Through output or DIT) - One channel supports Differential Output (RS422 Line Output Buffer) Auxiliary Digital Input De-emphasis for 32kHz, 44.1kHz and 48kHz Detection Functions - Non-PCM Bit Stream Detection - DTS-CD Bit Stream Detection - Sampling Frequency Detection: (22.05kHz, 24kHz, 32kHz, 44.1kHz, 48kHz, 64kHz, 88.2kHz, 96kHz, 176.4kHz and 192kHz) - Unlock & Parity Error Detection - DAT Start ID Detection Up to 24bit Audio Data Format Audio Interface: Master or Slave Mode 192-bit Channel Status Buffer Burst Preamble bit Pc and Pd Buffer for Non-PCM bit stream Q-subcode Buffer for CD bit stream Serial μP Interface: 4-wire or I2C (max. 400kHz) Two Master Clock Outputs: 64fs/128fs/256fs/512fs Operating Voltage: 2.7 to 3.6V with 5V Logic Tolerance Package: 64pin LQFP Ta: -20 to 85°C MS0573-E-01 2010/09 -1- [AK4115] XTI1 XTO1 AVSS AVDD R VCOM FILT ACKS XTI2 XTO2 X'tal X'tal Oscillator Oscillator PSEL Clock Recovery Clock Clock MCKO1 Selector Generator MCKO2 RXP0 RXN0 DEM RX1 8 to 3 DAIF Input Decoder RX2 RX3 RX4 Audio I/F for RX/TX LRCK BICK SDTO Selector RX5 DAUX RX6 RX7 ELRCK TX0 EBICK Audio I/F for TX TXP1 TXN1 ELRCK EMCLK ASYNC DIT Channel Status TVDD TVSS buffer Q-subcode buffer DVDD PDN DVSS CSN OVDD AC-3/MPEG OVSS Detect XTL1 XTL0 VIN B, C, U Error & STATUS Detect INT0 VOUT INT1 µP I/F CCLK CDTO CDTI P/SN= “L” IIC Figure 1. AK4115 Block Diagram in serial mode MS0573-E-01 2010/09 -2- [AK4115] XTI1 XTO1 AVSS AVDD R VCOM FILT XSEL ACKS XTI2 XTO2 X'tal X'tal Oscillator Oscillator PSEL Clock Recovery Clock Clock MCKO1 Selector Generator MCKO2 RXP0 RXN0 4 to 2 RX1 Input RX2 Selector DEM DAIF Audio I/F Decoder RX3 for RX/TX IPS0 LRCK BICK SDTO DAUX DIF0 DIF1 EBICK ELRCK TX0 EMCK TXP1 TXN1 DIT TVDD TVSS PDN DVDD DVSS OCKS0 OVDD AC-3/MPEG OVSS Detect XTL1 XTL0 VIN B,C,U,VOUT OCKS1 Error & CM0 STATUS Detect INT0 INT1 CM1 P/SN= “H”IPS1 Figure 2. AK4115 Block Diagram in parallel mode MS0573-E-01 2010/09 -3- [AK4115] ■ Ordering Guide -20 ~ +85 °C 64pin LQFP (0.5mm pitch) Evaluation board for AK4115 AK4115VQ AK4115 RX3 AVSS RX2 AVDD RX1 AVSS RXP0 RXN0 ACKS P/SN AVDD VCOM R AVSS 61 60 59 58 57 56 55 54 53 52 51 50 49 AVDD 63 62 IPS0/RX4 64 ■ Pin Layout 1 48 FILT TEST 2 47 XTL1 DIF1/RX6 3 46 XTL0 PDN 4 45 PSEL XSEL/RX7 5 44 IPS1/IIC DVDD 6 43 BVSS VIN 7 42 DVSS DAUX 8 41 DVDD DIF0/RX5 Top View 40 OCKS0/CSN/CAD0 MCKO1 10 39 OCKS1/CCLK/SCL MCKO2 11 38 CM1/CDTI/SDA OVDD 12 37 CM0/CDTO/CAD1 OVSS 13 36 INT1 BICK 14 35 INT0 SDTO 15 34 ELRCK LRCK 16 33 EMCK 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 C U VOUT TVDD TX0 TXP1 TXN1 TVSS XTI1 XTO1 XTI2 XTO2 OVDD OVSS EBICK 9 B DVSS MS0573-E-01 2010/09 -4- [AK4115] PIN/FUNCTION No. Pin Name DIF0 RX5 I/O I I Function Audio Data Interface Format #0 Pin in parallel mode 1 Receiver Channel #5 Pin in serial mode (Internal biased pin) TEST Pin 2 TEST I This pin must be connected to AVSS. DIF1 I Audio Data Interface Format #1 Pin in parallel mode 3 RX6 I Receiver Channel #6 Pin in serial mode (Internal biased pin) Power-Down Mode Pin 4 PDN I When “L”, the AK4115 is powered-down and reset. X’tal Oscillator Selection Pin in parallel mode “L”: X’tal #1 is powered-up. XSEL I 5 “H”: X’tal #2 is powered-up. XSEL pin and XSEL bit are ORed. RX7 I Receiver Channel #7 Pin in serial mode (Internal biased pin) 6 DVDD Digital Power Supply Pin, 3.3V 7 VIN I V-bit Input Pin for Transmitter Output 8 DAUX I Auxiliary Audio Data Input Pin 9 DVSS Digital Ground Pin 10 MCKO1 O Master Clock Output #1 Pin 11 MCKO2 O Master Clock Output #2 Pin 12 OVDD Digital Power Supply Pin, 3.3V 13 OVSS Digital Ground Pin 14 BICK I/O Audio Serial Data Clock Pin 15 SDTO O Audio Serial Data Output Pin 16 LRCK I/O Channel Clock Pin 17 B I/O Block-Start Input/Output Pin 18 C I/O C-bit Input/Output Pin 19 U I/O U-bit Input/Output Pin 20 VOUT O V-bit Output Pin for Receiver 21 TVDD Input tolerance & TX Output Buffer Power Supply Pin, 3.3V or 5V 22 TX0 O Transmit Channel (Through Data) Output #0 Pin 23 TXP1 O Transmit Channel Positive Output #1 Pin 24 TXN1 O Transmit Channel Negative Output #1 Pin 25 TVSS Input & TX Output Buffer Ground pin 26 XTI1 I X’tal #1 Input Pin 27 XTO1 O X’tal #1 Output Pin 28 XTI2 I X’tal #2 Input Pin 29 XTO2 O X’tal #2 Output Pin 30 OVDD Digital Power Supply Pin, 3.3V 31 OVSS Digital Ground Pin 32 EBICK I/O External Serial Data Clock Pin 33 EMCK I External Master Clock Input Pin 34 ELRCK I/O External Channel Clock Pin 35 INT0 O Interrupt #0 Pin 36 INT1 O Interrupt #1 Pin Note 1. Do not allow digital input pins except internal biased pins to float. MS0573-E-01 2010/09 -5- [AK4115] PIN/FUNCTION (Continued) No. Pin Name CM0 CDTO CAD1 CM1 CDTI I/O I O I I I Function Master Clock Operation Mode #0 Pin in parallel mode 37 Control Data Output Pin in serial mode, IIC pin = “L”. Chip Address #1 Pin in serial mode, IIC pin = “H”. Master Clock Operation Mode #1 Pin in parallel mode Control Data Input Pin in serial mode, IIC pin = “L”. 38 Control Data Pin in serial mode, IIC pin = “H”. SDA I/O An external pull-up resistor is required. OCKS1 I Output Clock Select #1 Pin in parallel mode CCLK I Control Data Clock Pin in serial mode, IIC pin = “L” 39 Control Data Clock Pin in serial mode, IIC pin = “H” SCL I An external pull-up resistor is required. OCKS0 I Output Clock Select #0 Pin in parallel mode 40 CSN I Chip Select Pin in serial mode, IIC pin = “L”. CAD0 I Chip Address #0 Pin in serial mode, IIC pin = “H”. 41 DVDD Digital Power Supply Pin, 3.3V 42 DVSS Digital Ground Pin 43 BVSS Substrate Ground Pin IPS1 I Input Channel Select #1 Pin in parallel mode 44 IIC Select Pin in serial mode IIC I “L”: 4-wire Serial, “H”: I2C PLL Source Select Pin 45 PSEL I “L”: S/PDIF Input, “H”: ELRCK Input Clock PSEL pin and PSEL bit are ORed in serial mode. 46 XTL0 I X’tal Frequency Select #0 Pin 47 XTL1 I X’tal Frequency Select #1 Pin 48 FILT O PLL Loop Filter Pin 49 AVSS Analog Ground Pin External Resistor Pin 50 R O 10kΩ ±1% resistor should be connected to AVSS externally. Common Voltage Output Pin 51 VCOM O 4.7µF capacitor should be connected to AVSS externally. 52 AVDD Analog Power Supply Pin, 3.3V Parallel/Serial Select Pin 53 P/SN I “L”: Serial Mode, “H”: Parallel Mode Master Clock Frequency Auto Setting Mode Pin. 54 “L”: Disable, “H”: Enable ACKS I ACKS pin and ACKS bit are ORed in serial mode. Receiver Channel #0 Negative Input Pin (Internal biased pin) 55 RXN0 I In serial mode, this channel is selected as default channel. Receiver Channel #0 Positive Input Pin (Internal biased pin) 56 RXP0 I In serial mode, this channel is selected as default channel. 57 AVSS Analog Ground Pin 58 RX1 I Receiver Channel #1 Pin (Internal biased pin) 59 AVDD Analog Power Supply Pin, 3.3V 60 RX2 I Receiver Channel #2 Pin (Internal biased pin) 61 AVSS Analog Ground Pin 62 RX3 I Receiver Channel #3 Pin (Internal biased pin) 63 AVDD Analog Power Supply Pin, 3.3V IPS0 I Input Channel Select #0 Pin in parallel mode 64 RX4 I Receiver Channel #4 Pin in serial mode (Internal biased pin) Note 1. Do not allow digital input pins except internal biased pins to float. MS0573-E-01 2010/09 -6- [AK4115] ■ Handling of Unused Pin The unused I/O pin should be processed appropriately as below. 1. Serial Mode (P/SN pin = “L”) Classification Analog Input Analog Output Digital Input Digital Output Digital Input/Output Pin Name RXP0, RXN0, RX7-1 TEST FILT VIN, DAUX, XTI1, XTI2, EMCK MCKO1, MCKO2, VOUT, TX0, TXP1, TXN1, XTO1, XTO2, INT0, INT1, CDTO (IIC pin = “L”) B, U, C EBICK, ELRCK Setting These pins should be open. This pin should be connected to AVSS. This pin should be open. These pin should be connected to DVSS. These pins should be open. These pins should be open when BCU_IC bit is “1”. These pins should be DVSS when BCU_IO bit is “0”. These pins should be open in master mode. These pins should be connected to DVSS in slave mode. 2. Parallel Mode (P/SN pin = “H”) Classification Analog Input Analog Output Digital Input Digital Output Pin Name RXP0, RXN0, RX3-1 TEST FILT VIN, DAUX, XTI1, XTI2, EMCK, EBICK, ELRCK MCKO1, MCKO2, VOUT, TX0, TXP1, TXN1, XTO1, XTO2, INT0, INT1, B, U, C Setting These pins should be open. This pin should be connected to AVSS. This pin should be open. These pin should be connected to DVSS. These pins should be open. MS0573-E-01 2010/09 -7- [AK4115] ABSOLUTE MAXIMUM RATINGS (AVSS=OVSS=DVSS=TVSS=BVSS=0V; Note 2) Parameter Symbol min max Power Supplies: Analog AVDD -0.3 4.6 Digital DVDD -0.3 4.6 Logic Output Buffer OVDD -0.3 4.6 Input tolerance and TX Buffer TVDD -0.3 6.0 | BVSS – AVSS | (Note 3) 0.3 ΔGND1 | BVSS – OVSS | (Note 3) 0.3 ΔGND2 | BVSS – DVSS | (Note 3) 0.3 ΔGND3 | BVSS – TVSS | (Note 3) 0.3 ΔGND4 Input Current (Any pins except supplies) IIN ±10 Input Voltage (Note 4) VIN -0.3 “TVDD+0.3” or 6.0 Ambient Temperature (Power applied) Ta -20 85 Storage Temperature Tstg -65 150 Note 2. All voltages with respect to ground. Note 3. AVSS, OVSS, DVSS, BVSS and TVSS must be connected to the same ground plane. Note 4. All input pins. The maximum value is low value either “TVDD+0.3V” or “6.0V”. Pull-up resistor at SDA and SCL pins should be connected to (TVDD+0.3)V or less voltage. Units V V V V V V V V mA V °C °C WARNING: Operation at or beyond these limits may result in permanent damage to the device. Normal operation is not guaranteed at these extremes. RECOMMENDED OPERATING CONDITIONS (AVSS=OVSS=DVSS=TVSS=BVSS=0V; Note 2) Parameter Symbol min typ Power Analog AVDD 2.7 3.3 Supplies: Digital DVDD 2.7 3.3 (Note 5) Logic Output Buffer OVDD 2.7 3.3 Input tolerance and TX Buffer TVDD DVDD 5.0 Difference AVDD – DVDD -0.3 0 AVDD – OVDD -0.3 0 OVDD – DVDD -0.3 0 Note 2. All voltages with respect to ground. Note 5. The power up sequence among AVDD, DVDD, OVDD and TVDD is not critical. max 3.6 3.6 3.6 5.5 0.3 0.3 0.3 Units V V V V V V V *AKM assumes no responsibility for the usage beyond the conditions in this data sheet. MS0573-E-01 2010/09 -8- [AK4115] S/PDIF RECEIVER CHARACTERISTICS (Ta=25°C; AVDD=OVDD=DVDD=2.7~3.6V; TVDD=2.7~5.5V) Parameter Symbol min Input Resistance Zin Input Voltage VTH 200 Input Sample Frequency fs 22 Time deviation Jitter RX input (PSEL = “0”) ELRCK input (PSEL = “1”) Cycle - to - Cycle Jitter RX input (PSEL = “0”) ELRCK input (PSEL = “1”) - typ 10 - max 216 Units kΩ mVpp kHz 100 300 - ps RMS ps RMS 70 70 - ps RMS ps RMS DC CHARACTERISTICS (Ta=25°C; AVDD=OVDD=DVDD=2.7~3.6V; TVDD=2.7~5.5V; unless otherwise specified) Parameter Symbol min typ max Units Power Supply Current Normal operation: PDN pin = “H” (Note 6) AVDD+DVDD+OVDD: 28 42 mA TVDD: 30 45 mA Power down: PDN pin = “L” (Note 7) AVDD+DVDD+OVDD+TVDD: 10 100 μA High-Level Input Voltage VIH 70%DVDD TVDD V Low-Level Input Voltage VIL DVSS-0.3 30%DVDD V Input Level at AC coupling (Only ELRCK pin) VAC 0.5 TVDD Vpp Except for TX0, TXN1 and TXP1 pins VOH OVDD-0.4 V High-Level Output Voltage (Iout=-400μA) Low-Level Output Voltage VOL 0.4 V (Except SDA pin: Iout=400μA) VOL 0.4 V ( SDA pin: Iout= 3mA) TX0 Output Level Output Level (Note 8) VTXO0 0.4 0.5 0.6 V TXN1 and TXP1 pins Professional mode (TVDD= 4.5 ~ 5.5V) RTXPN 88 110 132 Output Impedance (Rp + Rn + R1) (Note 9) Ω Consumer Mode (TVDD = 2.7 ~ 5.5V) VTXO1 0.4 0.5 0.6 V Output Level (Note 10) Input Leakage Current Iin ± 10 μA Note 6. AVDD, OVDD, DVDD = 3.3V, TVDD=5.0V, CL=20pF, fs=216kHz, X'tal=24.576MHz, Clock Operation Mode 2, OCKS1=1, OCKS0=1, TX0 output circuit: Figure 23, TX1 output circuit: Figure 25. AVDD=10mA (typ), OVDD+DVDD=18mA (typ) Note 7. RX inputs are open and all digital input pins are held TVDD or DVSS. Note 8. By using Figure 23 or Figure 24. Note 9. Rp: Output impedance of TXP1, Rn: Output impedance of TXN1, R1 = 75Ω. By using Figure 25. Note 10. By using Figure 26 MS0573-E-01 2010/09 -9- [AK4115] SWITCHING CHARACTERISTICS (Ta=25°C; AVDD=OVDD=DVDD=2.7~3.6V, TVDD=2.7~5.5V; CL=20pF) Parameter Symbol min Master Clock Timing Crystal Resonator Frequency fXTAL 11.2896 External Clock Frequency fECLK 11.2896 Duty dECLK 40 MCKO1 Output Frequency fMCK1 2.816 Duty dMCK1 40 MCKO2 Output Frequency fMCK2 1.408 Duty dMCK2 40 PLL Clock Recover Frequency (RX7-0) fpll 22 LRCK Frequency fs 22 Duty Cycle (at Slave Mode) dLCK 45 Duty Cycle (at Master Mode) dLCK Audio Interface Timing 1 Slave Mode BICK Period tBCK 72 BICK Pulse Width Low tBCKL 27 Pulse Width High tBCKH 27 tLRB 15 LRCK Edge to BICK “↑” (Note 11) tBLR 15 BICK “↑” to LRCK Edge (Note 11) tLRM LRCK to SDTO (MSB) (3.0V ≤ DVDD,OVDD ≤ 3.6V) tBSD BICK “↓” to SDTO (3.0V ≤ DVDD,OVDD ≤ 3.6V) tLRM LRCK to SDTO (MSB) (2.7V ≤ DVDD,OVDD < 3.0V) tBSD (2.7 V≤ DVDD,OVDD < 3.0V) BICK “↓” to SDTO tDXH 15 DAUX Hold Time tDXS 15 DAUX Setup Time Master Mode BICK Frequency fBCK BICK Duty dBCK tMBLR -15 BICK “↓” to LRCK tBSD BICK “↓” to SDTO tDXH 15 DAUX Hold Time DAUX Setup Time tDXS 15 Master Clock Timing 2 EMCK Frequency fECLK2 2.816 Duty dECLK2 40 ELRCK PLL Lock Range fEPLL 22 Frequency fs 22 Duty dLCK 40 Audio Interface Timing 2 Slave Mode EBICK Period tEBCK 72 EBICK Pulse Width Low tEBCKL 27 Pulse Width High tEBCKH 27 tELRB 15 ELRCK Edge to BICK “↑” (Note 12) tEBLR 15 EBICK “↑” to ELRCK Edge (Note 12) tEDXH 15 DAUX Hold Time tEDXS 15 DAUX Setup Time Master Mode EBICK Frequency fEBCK EBICK Duty dEBCK tEMBLR -15 EBICK “↓” to ELRCK tEDXH 15 DAUX Hold Time DAUX Setup Time tEDXS 15 Note 11. BICK rising edge must not occur at the same time as LRCK edge. Note 12. EBICK rising edge must not occur at the same time as ELRCK edge. MS0573-E-01 typ max Units 50 50 50 50 24.576 27.648 60 27.648 60 27.648 60 216 216 55 - MHz MHz % MHz % MHz % kHz kHz % % - 20 20 25 25 - ns ns ns ns ns ns ns ns ns ns ns 64fs 50 - 15 15 - Hz % ns ns ns ns 50 50 27.648 60 216 216 60 MHz % kHz kHz % - - ns ns ns ns ns ns ns 64fs 50 - 15 - Hz % ns ns ns 2010/09 - 10 - [AK4115] SWITCHING CHARACTERISTICS (Continued) (Ta=25°C; AVDD=OVDD=DVDD=2.7~3.6V, TVDD=2.7~5.5V; CL=20pF) Parameter Symbol min Control Interface Timing (4-wire serial mode) CCLK Period tCCK 200 CCLK Pulse Width Low tCCKL 80 Pulse Width High tCCKH 80 CDTI Setup Time tCDS 50 CDTI Hold Time tCDH 50 CSN “H” Time tCSW 150 tCSS 50 CSN “↓” to CCLK “↑” tCSH 50 CCLK “↑” to CSN “↑” tDCD CDTO Delay tCCZ CSN “↑” to CDTO Hi-Z 2 Control Interface Timing (I C Bus mode): SCL Clock Frequency fSCL Bus Free Time Between Transmissions tBUF 1.3 Start Condition Hold Time (prior to first clock pulse) tHD:STA 0.6 Clock Low Time tLOW 1.3 Clock High Time tHIGH 0.6 Setup Time for Repeated Start Condition tSU:STA 0.6 SDA Hold Time from SCL Falling (Note 13) tHD:DAT 0 SDA Setup Time from SCL Rising tSU:DAT 0.1 Rise Time of Both SDA and SCL Lines tR Fall Time of Both SDA and SCL Lines tF Setup Time for Stop Condition tSU:STO 0.6 Capacitive load on bus Cb Pulse Width of Spike Noise Suppressed by Input Filter tSP 0 Reset Timing PDN Pulse Width tPW 150 Note 13. Data must be held for sufficient time to bridge the 300ns transition time of SCL. Note 14. I2C-bus is a tradmark of NXP B.V. MS0573-E-01 typ max Units - 45 70 ns ns ns ns ns ns ns ns ns ns - 400 0.3 0.3 400 50 kHz μs μs μs μs μs μs μs μs μs μs pF ns - - ns 2010/09 - 11 - [AK4115] ■ Timing Diagram 1/fECLK VIH XTI VIL tECLKH tECLKL dECLK = tECLKH x fECLK x 100 = tECLKL x fECLK x 100 1/fMCK1 MCKO1 50%OVDD tMCKH1 tMCKL1 dMCK1 = tMCKH1 x fMCK1 x 100 = tMCKL1 x fMCK1 x 100 1/fMCK2 MCKO2 50%OVDD tMCKH2 tMCKL2 dMCK2 = tMCKH2 x fMCK2 x 100 = tMCKL2 x fMCK2 x 100 1/fs VIH LRCK VIL tLRH tLRL dLCK = tLRH x fs x 100 = tLRL x fs x 100 1/fECLK2 VIH EMCK VIL tECLKH2 tECLKL2 dECLK2 = tECLKH2 x fECLK2 x 100 = tECLKL2 x fECLK2 x 100 1/fs VIH ELRCK VIL tELRH tELRL dELCK = tELRH x fs x 100 = tELRL x fs x 100 Figure 3. Clock Timing MS0573-E-01 2010/09 - 12 - [AK4115] VIH LRCK VIL tBCK tBLR tLRB tBCKL tBCKH VIH BICK VIL tLRM tBSD 50%OVDD SDTO tDXS tDXH VIH DAUX VIL Figure 4. Serial Interface Timing 1 (Slave Mode) 50%OVDD LRCK tMBLR 50%OVDD BICK tBSD 50%OVDD SDTO tDXS tDXH VIH DAUX VIL Figure 5. Serial Interface Timing 1 (Master Mode) VIH ELRCK VIL tEBCK tEBLR tELRB tEBCKL tEBCKH VIH EBICK VIL tEDXS tEDXH VIH DAUX VIL Figure 6. Serial Interface Timing 2 (Slave Mode) MS0573-E-01 2010/09 - 13 - [AK4115] ELRCK 50%OVDD tEMBLR 50%OVDD EBICK tEDXS tEDXH VIH DAUX VIL Figure 7. Serial Interface Timing 2 (Master Mode) VIH CSN VIL tCSS tCCK tCCKL tCCKH VIH CCLK VIL tCDH tCDS CDTI C1 C0 0 0 VIH VIL Hi-Z CDTO Figure 8. WRITE/READ Command Input Timing in 4-wire serial mode tCSW VIH CSN VIL tCSH VIH CCLK CDTI CDTO VIL D3 D2 D1 D0 VIH VIL Hi-Z Figure 9. WRITE Data Input Timing in 4-wire serial mode MS0573-E-01 2010/09 - 14 - [AK4115] VIH CSN VIL VIH CCLK VIL A1 CDTI VIH A0 VIL tDCD Hi-Z CDTO D7 D6 D5 50%OVDD Figure 10. READ Data Output Timing 1 in 4-wire serial mode tCSW VIH CSN VIL tCSH VIH CCLK VIL VIH CDTI VIL tCCZ CDTO D3 D2 D1 D0 50%OVDD Figure 11. READ Data Input Timing 2 in 4-wire serial mode VIH SDA VIL tLOW tBUF tR tHIGH tF tSP VIH SCL VIL tHD:STA Stop Start tHD:DAT tSU:DAT tSU:STA tSU:STO Start Stop Figure 12. I2C Bus mode Timing tPW PDN VIL Figure 13. Power Down & Reset Timing MS0573-E-01 2010/09 - 15 - [AK4115] OPERATION OVERVIEW ■ Non-PCM (Dolby Digital, MPEG, etc) and DTS-CD Bitstream Detection The AK4115 has a non-PCM bitstream auto-detection function, When the 32-bit mode Non-PCM preamble based on Dolby “Dolby Digital Data Stream in IEC 60958 Interface” is detected, the NPCM bit sets to “1”. The 96-bit sync code consists of 0x0000, 0x0000, 0x0000, 0x0000, 0xF872 and 0x4E1F. Detection of this pattern will set the NPCM bit to “1”. Once the NPCM bit is set to “1”, it will remain “1” until 4096 frames pass through the chip without an additional sync pattern being detected. When those preambles are detected, the burst preambles Pc (burst information: Figure 51) and Pd (length code: Figure 52) that follow those sync codes are stored to registers. The AK4115 has also a DTS-CD bitstream auto-detection function. When the AK4115 detects DTS-CD bitstream, the DTSCD bit sets to “1”. If the next sync code does not occur within 4096frames, the DTSCD bit sets to “0” until no-PCM bitstream is detected again. The ORed value of NPCM and DTSCD bits are output to AUTO bit. The AK4115 detects the 14-bit sync word and the 16-bit sync word of a DTS-CD bitstream, the detection function can be set ON/OFF by DTS14 and DTS16 bits in serial mode. In parallel mode, the logical OR value of the AUTO and DTS-CD bits are outputted to the INT1 pin. The DTS-CD bit detects both the 14-bit sync word and the 16-bit sync word. ■ 216kHz Clock Recovery The integrated low jitter PLL has a wide lock range from 22kHz to 216kHz. The AK4115 has a sampling frequency detection function (22.05kHz, 24kHz, 32kHz, 44.1kHz, 48kHz, 64kHz, 88.2kHz, 96kHz, 176.4kHz and 192kHz) that uses either a clock comparison against the X’tal oscillator from the setting of XTL1-0, or the channel status information. The PLL loses lock when the received sync interval is incorrect. ■ Reference Clock for PLL The reference clock for the PLL can select the bi-phase signal or the clock supplied from the ELRCK pin. The bi-phase signals are supplied to RX7-0 pins and the ELRCK pin is supplied to a sampled clock (1fs) from the word clock (typically used by studio equipment). This is selected by the PSEL bit or the PSEL pin. PSEL bit and PSEL pin are ORed internally. PSEL Reference Clock for PLL 0 RX Input 1 ELRCK Input Table 1. Setting of PLL Reference Clock Default ■ PLL Lock Time The lock time at PSEL = “0” depends on sampling frequency (fs) and FAST bit (See Table 2). FAST bit is useful at lower sampling frequency and is fixed to “1” in parallel mode. When PSEL is “1”, the lock time is 35ms (max) and is not related to the setting of the FAST bit. The lock time in Table 2 does not include the power-up time of VCOM voltage. Therefore, the power-up time of VCOM voltage must be added when PDN pin changes from “L” to “H”. The power-up time of VCOM voltage is max. 15ms (Capacitor value of VCOM pin = 4.7μF). PSEL FAST bit PLL Lock Time 0 0 ≤ (20ms + 384/fs) 0 1 ≤ (20ms + 1/fs) 1 ≤ 35ms Table 2. PLL Lock Time (fs: Sampling Frequency) MS0573-E-01 Default 2010/09 - 16 - [AK4115] ■ Word Clock (Studio Sync Clock) The word clock is used to synchronize clocks among studio equipment and is always synchronized to the sampling frequency (1fs). The internal PLL generates MCLK, BICK and LRCK from the word clock supplied to the ELRCK pin. The PLL lock range is 22kHz to 216kHz. The word clock (ELRCK pin) can receive signal levels of 0.5Vpp(min) when AC coupled. In master mode, the clock phase between ELRCK pin and LRCK pin is within ± 5%. When the AK4115 is supplied with a bi-phase signal and a word clock (ELRCK), the phase error between the LRCK and ELRCK is within ±1/(128fs). Therefore, use LRCK and not ELRCK for the serial data output stream. When the word clock is not synchronized to the bi-phase signal, WSYNC bit should be set to “0”. ■ DIT/DIR Mode The AK4115 operates in either synchronous mode or asynchronous mode. In synchronous mode, transmitter and receiver are operated by the same clock source. In asynchronous mode, transmitter and receiver are operated by different a sampling frequencies that are selected by the ASYNC bit. Frequency multiples are not required in asynchronous mode. 1. Synchronous Mode: ASYNC bit = “0” PSEL and CM1-0 select the clock source and the data source for SDTO. In Mode 2, the clock source is switched from PLL to X'tal when the PLL goes to the unlock state. In Mode 3, the clock source is fixed to X’tal, but PLL is also operation and the recovered data such as channel status bit can be monitored. For Mode 2 and Mode 3, it is recommended that the frequency of X’tal is different from the recovered frequency of the PLL. In Modes 4-6, the PLL source is ELRCK and MCKO1/2, BICK and LRCK are generated by the PLL. The data source of SDTO is always DAUX. Mode PSEL CM1 CM0 UNLOCK PLL Status 0 0 0 0 - ON 1 0 0 1 - OFF X'tal Status ON (Note 16) ON 2 0 1 0 0 ON ON 3 0 1 1 1 - ON ON 4 1 0 0 - ON 5 1 0 1 - OFF ON ON ON (Note 16) ON 6 1 1 0 0 ON ON Clock source PLL (RX) X'tal PLL (RX) X'tal X’tal PLL (ELRCK) X’tal PLL (ELRCK) X'tal Clock I/O SDTO Note 17 RX Note 17 DAUX Note 17 RX Note 17 Note 17 DAUX DAUX Note 17 DAUX Note 17 DAUX Note 17 DAUX Note 17 DAUX 1 ON ON Note 15. ON: Oscillation (Power-up), OFF: STOP (Power-down) Note 16: When the X’tal is not used as clock comparison for fs detection (i.e. XTL1,0= “1,1”), the X’tal is OFF. Note 17. MCKO1/2, BICK, LRCK Table 3. Clock operation for DIT/DIR in synchronous mode MS0573-E-01 2010/09 - 17 - [AK4115] XTI1 XTO1 X'tal ACKS XTI2 XTO2 X'tal XSEL Oscillator Oscillator Clock Recovery Clock Selector Clock MCKO1 (CM1-0) Generator MCKO2 RXP0 RXN0 RX1 DEM 8 to 3 DAIF Input Decoder RX2 RX3 RX4 LRCK Audio I/F BICK for RX/TX SDTO Selector RX5 DAUX RX6 RX7 TX0 TXP1 TXN1 DIT Figure 14. Clocks for DIT/DIR in synchronous mode (PSEL bit = “0”) XTI1 XTO1 X'tal ACKS XSEL XTO2 X'tal Oscillator Oscillator Clock Recovery XTI2 Clock Selector Clock MCKO1 (CM1-0) Generator MCKO2 RXP0 RXN0 RX1 8 to 2 Audio I/F Input for RX/TX RX2 RX3 RX4 LRCK BICK SDTO Selector RX5 DAUX RX6 RX7 ELRCK TX0 TXP1 TXN1 DIT Figure 15. Clocks for DIT/DIR in synchronous mode (PSEL bit = “1”) MS0573-E-01 2010/09 - 18 - [AK4115] 2. Asynchronous Mode: ASYNC bit = “1”, PSEL = “0” When ASYNC bit is “1”, DIT and DIR can operate at different sample rates(non-multiples). In Mode1, Mode2 (When the PLL is the unlock state) and Mode3, SDTO is fixed “L”. The input timing of DAUX should be synchronized with ELRCK and EBCIK. The master clock of TX can be selected to either X’tal or EMCK by the MSEL bit (See Table 4). MSEL bit Master Clock 0 X’tal Defalut 1 EMCK Table 4. Master clock setting for TX in asynchronous mode. RX Clock I/O Mode CM1 CM0 UNLOCK PLL Status X'tal Status 0 0 0 - ON ON (Note 19) PLL (RX) Note 20 RX 1 0 1 - OFF ON X'tal Note 20 “L” 0 ON ON PLL (RX) Note 20 RX 1 ON ON X'tal Note 20 “L” - ON ON X'tal Note 20 “L” 2 1 3 1 Clock Source SDTO 0 1 TX Clock Clock Source I/O X’tal or Note 21 EMCK (Note 22) X’tal or Note 21 EMCK X’tal or Note 21 EMCK X’tal or Note 21 EMCK X’tal or Note 21 EMCK Note 18. ON: Oscillation (Power-up), OFF: STOP (Power-down) Note 19 When the X’tal is not used as clock comparison for sampling frequency detection (i.e. XTL1,0 = “1,1”), the X’tal is OFF. Note 20: MCKO1/2, BICK, LRCK Note 21. EMCK or X’tal, EBICK, ELRCK, DAUX Note 22. When X’tal is OFF, the clock source supports EMCK only. Table 5. Clock operation for DIT/DIR in asynchronous mode XTI1 XTO1 X'tal ACKS XTI2 X'tal XSEL Oscillator Oscillator Clock Recovery XTO2 Clock Selector Clock MCKO1 (CM1-0) Generator MCKO2 RXP0 RXN0 RX1 DEM 8 to 3 DAIF Input Decoder RX2 RX3 RX4 Audio I/F for RX “L” Selector RX5 LRCK BICK SDTO MSEL RX6 EMCK RX7 Audio I/F TX0 for TX TXP1 TXN1 ELRCK EBICK DAUX DIT Figure 16. Clocks for DIT/DIR in asynchronous mode MS0573-E-01 2010/09 - 19 - [AK4115] ■ Block start, Channel status bit, User bit and Validity bit The AK4115 can control and monitor block start, channel status bits, user bits and validity bit for RX and TX. B, C and U pins are bi-directional and the direction of input/output can be selected by the BCU_IO bit. B, C, U and VOUT pins become “L” (BCU_IO bit = “1”) in an unlocked state of Mode 2. a. Serial mode & Except AES3 mode (P/SN pin = “L”, AES3 bit = “0”) Block RX ASYNC BCU_IO Start Channel Validity bit bit User bit (B pin) Status bit bit VOUT pin 0 Input CR191-0 bits N/A VRX bit (Note 24) 0 VRX bit C pin U pin VOUT pin 1 Output CR191-0 bits (Note 24) (Note 23) 0 Input CR191-0 bits N/A 1 VRX bit TX Channel Status bit C pin CT191-0 bits (Note 25) User bit U pin CT191-0 bits All “0” data (Note 27) C pin CT191-0 bits (Note 25) U pin VOUT pin C pin All U pin VRX bit CT191-0 bits CR191-0 bits “0” data (Note 24) (Note 23) Note 23. Channel status bit for RX can be monitored by both C pin and CR191-0 bits. Note 24. Validity bit for RX can be monitored by both VOUT pin and VRX bit. Note 25. C pin and CT191-0 bits are ORed internally. Note 26. VIN pin and VTX bit are ORed internally. Note 27. When UDIT bit is “1”, the recovered U bits are used for DIT(DIR-DIT loop mode of U bit). 1 Output Validity bit VIN pin VTX bit (Note 26) VIN pin VTX bit (Note 26) VIN pin VTX bit (Note 26) VTX bit Table 6. Block start, Channel Status bit, User bit and Validity bit in serial mode except AES3 mode (N/A: Not available) MS0573-E-01 2010/09 - 20 - [AK4115] b. Serial mode & AES3 mode (P/SN pin = “L”, AES3 bit = “1”, ASYNC bit = “0”) Block RX TX DIF1 BCU_IO Start Channel Validity Channel bit bit User bit User bit (B pin) Status bit bit Status bit VOUT pin CR191-0 bits C pin VRX bit SDTO pin U pin 0 Input SDTO pin CT191-0 bits SDTO pin (Note 28) (Note 32) (Note 31) 0 C pin VOUT pin All U pin CR191-0 bits VRX bit CT191-0 bits “0” data 1 Output SDTO pin SDTO pin SDTO pin (Note 35) (Note 30) (Note 29) (Note 31) VOUT pin CR191-0 bits CT191-0 bits VRX bit DAUX SDTO pin 0 Input SDTO pin DAUX pin pin SDTO pin (Note 28) (Note 33) (Note 31) 1 C pin VOUT pin U pin CT191-0 bits DAUX CR191-0 bits VRX bit 1 Output SDTO pin DAUX pin pin SDTO pin SDTO pin (Note 30) (Note 33) (Note 29) (Note 31) Note 28. Channel status bit for RX can be monitored by CR191-0 bits and SDTO pin. Note 29. Channel status bit for RX can be monitored by C pin, CR191-0 bits and SDTO pin. Note 30. User bit for RX can be monitored by U pin and SDTO pin. Note 31. Validity bit for RX can be monitored by VOUT pin, VRX bit and SDTO pin. Note 32. C pin and CT191-0 bits are ORed internally. Note 33. Channel status bit can select either CT191-0 bits or DAUX pin by the setting of CTX bit. Note 34. VIN pin and VTX bit are ORed internally. Note 35. When UDIT bit is “1”, the recovered U bits are used for DIT(DIR-DIT loop mode of U bit). Validity bit VIN pin VTX bit (Note 34) VIN pin VTX bit (Note 34) DAUX pin DAUX pin Table 7. Block start, Channel Status bit, User bit and Validity bit in serial mode & AES3 mode c. Parallel mode (P/SN pin = “H”) Block Start Channel (B pin) Status bit Output RX User bit TX Validity bit Channel Status bit User bit Validity bit Default value of All VIN pin CT191-0 bits “0” data Table 8. Block start, Channel Status bit, User bit and Validity bit in parallel mode C pin U pin VOUT pin MS0573-E-01 2010/09 - 21 - [AK4115] 1. Channel Status bit 1-1. RX The data recovered from the bi-phase input signal is stored in CR191-0 bits. When the BCU_IO bit = “1”, the channel status bits are available on the C pin according to the block signal timing. The channel status bits are outputted from SDTO pin with audio data in AES3 mode. 1-2. TX The channel status bit can controlled by the CT191-0 bits. When BCU_IO bit is “0”, the channel status bits are also controlled by C pin. CT191-0 bits and the signal on the C pin are ORed internally. The input to C pin is ignored in AES3 mode. When CTX bit is set to “0”, the channel status bits on DAUX pin are outputted with audio data from TX. When CTX bit is set to “1”, the values of CT191-0 bits are outputted with audio data from TX. When the CCRE bit is “1” and AK4115 is in professional mode (bit0 = “1”), the CRC code can be generated according to the professional mode definition in the AES3 standard. When the CCRE bit is “0”, the CRC data is not generated and the data from the CT191-0 bits is passed to the TX directly. In the consumer mode (bit0 = “0”), the CRC code is not generated. In the consumer mode (bit0 = “0”), bits20-23(audio channel) must be controlled by the CT20 bit. When the CT20 bit is “1”, the AK4115 corresponds to “stereo mode”, bits20-23 are set to “1000”(left channel) in sub-frame 1, and is set to “0100”(right channel) in sub-frame 2. When the CT20 bit is “0”, bits20-23 is set to “0000” in both sub-frame 1 and sub-frame 2. All CR191-0 bits are transferred to CT191-0 bits when the CTRAN bit changes from “0” to “1”. The transferred CT191-0 bits are valid after the next block start signal is detected. CTRAN bit goes to “0” after finishing the transfer. Don’t write to the CT191-0 bits when the CTRAN bit = “1”. 2. User bit 2-1. RX When the BCU_IO bit is “1”, the recovered user bit is available on the U pin according to block start timing. The user bits are outputted from SDTO pin with audio data in AES3 mode. 2-2. TX When the BCU_IO bit is “0”, the user bit is sent to the U pin according to block start timing. When BCU_IO bit is “1” and the ASYNC bit is “0”(synchronous mode), the user bit is controlled by the UDIT bit. When the UDIT bit is “0”, user bit is set to “0”. When the UDIT bit is “1”, the recovered U bits are used for DIT( DIR-DIT loop mode of U bit). This mode (UDIT bit = “1”) is enabled when the PLL is locked. The input to U pin is ignored in AES3 mode and the user bits on DAUX pin are outputted with audio data from TX. MS0573-E-01 2010/09 - 22 - [AK4115] 3. Validity bit 3-1. RX In synchronous mode, the validity bit is available on the VOUT pin according to block start timing. In asynchronous mode, the validity bit is available on the VOUT pin according to LRCK timing. The VRX bit is available in both modes. The validity bit is outputted from SDTO pin with audio data in AES3 mode. 3-2. TX The validity bit is controlled by the VIN pin or the VTX bit. Since the validity bit does not usually update every sub-frame cycle, it can be controlled by the VIN pin according to LRCK timing in synchronous mode. In asynchronous mode, it can be controlled by the VIN pin according to ELRCK timing. When the validity bit timing is synchronized with the block start timing , the BCU_IO bit should be “0”. In asynchronous mode, the validity bit cannot be controlled by the VIN pin when BCU_IO bit is set to “0”. The input to VIN pin and VTX bit are ignored in AES3 mode and the validity bit on DAUX is outputted with audio data from TX. 4. Block Start Signal Timing In synchronous mode, the block start signal timing depends on LRCK. In asynchronous mode, it depends on ELRCK. The channel status, user and validity bits are captured with the current audio sample. When the block start signal is an input (BCU_IO bit = “0”), the block start signal should stay high for more than one sub-frame. When the block start signal is an output (BCU_IO bit = “1”), the block start signal goes high at the start of frame 0 and remains high until the end of frame 39. The input to B pin is ignored in AES3 mode and the B bit on DAUX is used as the block start timing. B (Input) Don’t care Don’t care B (Output) C (or U,V) C(R191) C(L0) C(R0) C(L1) C(L38) C(R39) C(L40) R0 L1 L38 R39 LRCK(ELRCK) (Except I2S) LRCK(ELRCK) (I2S) SDTO (DAUX) R191 L0 L40 Figure 17. B, C, U, V Input/output timings MS0573-E-01 2010/09 - 23 - [AK4115] ■ Master Clock Output The AK4115 has two master clock outputs, MCKO1 and MCKO2. MCKO2 has two modes. These modes can be selected by the XMCK bit. 1) When XMCK bit = “0” These clocks are derived from either the recovered clock or the X'tal oscillator. The frequencies of the master clock outputs (MCKO1 and MCKO2) are set by OCKS0 and OCKS1 as shown in Table 9. The 512fs clock is changed into the 256fs clock when sampling frequency is 96kHz or 192kHz. The 512fs or 256fs clock is changed into the 128fs clock when sampling frequency is 192kHz. No. 0 1 2 3 OCKS1 0 0 1 1 OCKS0 0 1 0 1 MCKO1 pin MCKO2 pin X’tal 256fs 256fs 256fs 256fs 128fs 256fs 512fs 256fs 512fs 128fs 64fs 128fs Table 9. Master Clock Output Frequency fs (max) 96 kHz 96 kHz 48 kHz 192 kHz Default 2) When XMCK bit = “1” MCKO2 outputs the input clock of the XTI pin. The settings of CM1-0 and OCKS1-0 bits are ignored. The output frequency can be set by the DIV bit. MCKO1 outputs a clock that is selected by the CM1-0 bits and OCKS1-0 bits. XMCK bit DIV bit MCKO2 Clock Source MCKO2 Frequency 1 0 X’tal (Note 36) x1 1 1 X’tal (Note 36) x 1/2 Note 36. MCKO2 Clock Source is selected by XSEL bit. Table 10. Select output frequency of MCKO2 ■ Master Clock Auto Setting Mode The master clock auto setting mode detects the MCLK/LRCK ratio (selects Normal/Double/Quad automatically). When ACKS is “1”, this mode is enabled. The frequencies of MCKO1 and MCKO2 are shown in Table 11. In this mode, the settings of OCKS1-0 are ignored. This mode is only supported when the sampling frequency detection circuit is enabled in PLL mode.(refer to “Sampling Frequency and Pre-emphasis Detection” section.) When ELRCK is selected and XTL1-0 = “11”, this mode is not supported. In X’tal mode, the frequencies of MCKO1/MCKO2 depend upon OCKS1-0. The ACKS pin and ACKS bit are ORed internally. Mode MCKO1 MCKO2 Sampling Frequency Range Normal Speed 512fs 256fs 22kHz to 48kHz Double Speed 256fs 128fs 64kHz to 96kHz Quad Speed 128fs 64fs 176.4kHz to 216kHz Table 11. Master Clock Frequency Select (Master Clock Auto Setting Mode) MS0573-E-01 2010/09 - 24 - [AK4115] ■ X’tal Oscillator The AK4115 has two X’tal oscillators. They can not operate at the same time. The operation of the X’tal oscillator is selected by the XSEL bit or the XSEL pin. XSEL 0 1 Status X’tal #1 X’tal #2 Power-Up Power-Down Power-Down Power-Up Table 12. Setting of X’tal oscillator The following circuits are available to feed the clock to the XTI1/2 pins of AK4115. 1) X’tal XTI1/2 AK4115 XTO1/2 Note: External capacitance depends upon the crystal oscillator (typ. 5-10pF) Figure 18. X’tal mode 2) External clock XTI1/2 External Clock AK4115 XTO1/2 Figure 19. External clock mode 3) Fixed to the Clock Operation Mode 0 XTI1/2 AK4115 XTO1/2 Figure 20. OFF mode MS0573-E-01 2010/09 - 25 - [AK4115] ■ Sampling Frequency and Pre-emphasis Detection The AK4115 has two methods for detecting the sampling frequency: 1. Clock comparison between the recovered clock and X’tal oscillator 2. Sampling frequency information from channel status The method is selected by the XTL1,0 pins. When XTL1, 0 = “1,1”, the sampling frequency is detected by the channel status sampling frequency information. The detected frequency is available on the FS3-0 bits. XTL1 XTL0 0 0 1 1 0 1 0 1 X’tal Frequency X’tal #1 X’tal #2 11.2896MHz 12.288MHz 12.288MHz 11.2896MHz 24.576MHz 22.5792MHz (Use channel status) (Use channel status) Table 13. Reference X’tal frequency Except XTL1, 0 = “1,1” Register output fs FS3 0 0 0 0 0 0 1 1 1 1 1 FS2 FS1 Clock comparison (Note 37) FS0 Default XTL1, 0 = “1, 1” Consumer mode (Note 38) Byte3 Bit3,2,1,0 0000 0001 0010 0011 0100 0110 Professional mode (Note 39) Byte0 Bit7,6 01 Byte4 Bit6,5,4,3 0000 (Others) 0000 0000 1001 0001 0 44.1kHz 0 0 44.1kHz ± 3% 0 0 1 Reserved 0 48kHz 10 1 0 48kHz ± 3% 0 32kHz 11 1 1 32kHz ± 3% 1 22.05kHz 00 0 0 22.05kHz ± 3% 1 24kHz 0 0 1 0 24kHz ± 3% 0 1 1 64kHz 64kHz ± 3% 0 88.2kHz 1000 00 0 0 1010 88.2kHz ± 3% 0 96kHz 1010 00 1 0 0010 96kHz ± 3% 1 176.4kHz 1100 00 0 0 1011 176.4kHz ± 3% 1 192kHz 1 1 1 0 0 0 1 0 0011 192kHz ± 3% Note 37: At least ±3% range is identified as the value in the Table 14. In case of intermediate frequency of those two, FS3-0 bits indicate no value. When the frequency is ≥ 3% over 192kHz or ≤ 3% under 22kHz, FS3-0 bits may indicate “0001”, “0101”, “0111” or “1001”. Note 38: In consumer mode, Byte3 Bit3-0 are copied to FS3-0 bits. Note 39. In professional mode, FS3-0 bit indicates “0001” except for frequency shown by Table 14. Table 14. fs Information MS0573-E-01 2010/09 - 26 - [AK4115] The pre-emphasis information is detected and reported on PEM bit. This informations is extracted from channel 1 by default. It can be switched to channel 2 by the CS12 bit in control register. Byte 0 Bits 3-5 0 OFF ≠ 0X100 1 ON 0X100 Table 15. PEM in Consumer Mode PEM Pre-emphasis Byte 0 Bits 2-4 0 OFF ≠110 1 ON 110 Table 16. PEM in Professional Mode PEM Pre-emphasis ■ De-emphasis Filter Control The AK4115 includes a digital de-emphasis filter (tc=50/15μs). This is an IIR filter corresponds to four sampling frequencies (32kHz, 44.1kHz and 48kHz). When DEAU bit=“1”, the de-emphasis filter is enabled automatically by the sampling frequency and pre-emphasis information in the channel status. The AK4115 is in this mode by default. In parallel control mode, the AK4115 is always placed in this mode and the status bits in channel 1 control the de-emphasis filter. In serial control mode, DEM0/1 bits control the de-emphasis filter when the DEAU bit is “0”. The internal de-emphasis filter is bypassed and the recovered data is available without any change if either the pre-emphasis or de-emphasis mode is OFF. When the PEM bit is “0”, the internal de-emphasis filter is always bypassed. PEM 1 1 1 1 0 FS3 0 0 0 FS2 0 0 0 x x FS1 0 1 1 FS0 0 0 1 x x (Others) Mode 44.1kHz 48kHz 32kHz OFF OFF Table 17. De-emphasis Auto Control at DEAU bit = “1” (Default) PEM 1 1 1 1 0 DEM1 0 0 1 1 x DEM0 0 1 0 1 x Mode 44.1kHz OFF 48kHz 32kHz OFF Default Table 18. De-emphasis Manual Control at DEAU bit = “0” MS0573-E-01 2010/09 - 27 - [AK4115] ■ System Reset and Power-Down The AK4115 has a power-down mode for all circuits by PDN pin and can be partially powerd-down by PWN bit. The RSTN bit initializes the register and resets the internal timing. In parallel mode, only the control by PDN pin is enabled. The AK4115 should be reset once by bringing PDN pin = “L” upon power-up. PDN Pin: All analog and digital circuits are placed in power-down and reset mode by bringing PDN pin= “L”. All the registers are initialized, and clocks are stopped. Reading/Writing to the registers is disabled. RSTN Bit (Address 00H; D0): All the registers except PWN and RSTN bits are initialized by bringing RSTN bit = “0”. The internal timing is also initialized. Writing to registers is not available except the PWN and RSTN bits. Reading from the registers is disabled. PWN Bit (Address 00H; D1): The clock recovery is initialized by bringing PWN bit = “0”. In this case, the clocks are stopped. The registers are not initialized and the mode settings are maintained. Writing and reading to the registers are enabled. ■ Bi-phase Input Eight receiver inputs (RX7-0) are available in serial mode and four receiver inputs (RX3-0) are available in parallel mode. Each input includes an amplifier for unbalanced mode that can accept a signal of 200mVpp or more. IPS2-0 selects the receiver channel. IPS2 bit IPS1 bit IPS0 bit INPUT Data 0 0 0 RX0 0 0 1 RX1 0 1 0 RX2 0 1 1 RX3 1 0 0 RX4 1 0 1 RX5 1 1 0 RX6 1 1 1 RX7 Table 19. Recovery Data Select in serial mode Default IPS1 pin IPS0 pin INPUT Data 0 0 RX0 0 1 RX1 1 0 RX2 1 1 RX3 Table 20. Recovery Data Select in parallel mode MS0573-E-01 2010/09 - 28 - [AK4115] ■ Bi-phase Output The AK4115 has two transmitter outputs, TX0 and TX1. TX0 is a loop-through output that is selected from the RX input. TX0 output is selected from RX7-0 by the OPS00, OPS01 and OPS02 bits. In parallel mode, the source of the loop-through output from TX0 is fixed to RX0. TX1 accepts output from RX7-0 or the transmitter (DIT; the data from DAUX is transformed to IEC60958 format.). TX1 also has a true RS422 line driver (differential output). The source of the loop-through output from TX1 is selected from RX7-0 by the OPS10, OPS11 and OPS12 bits. When the DIT bit is set to “1”, TX1 is transmitted to DAUX data. In parallel mode, TX1 is fixed to DIT. OPS02 0 0 0 0 1 1 1 1 DIT 0 0 0 0 0 0 0 0 1 OPS01 OPS00 Output Data 0 0 RX0 0 1 RX1 1 0 RX2 1 1 RX3 0 0 RX4 0 1 RX5 1 0 RX6 1 1 RX7 Table 21. Output Data Select for TX0 OPS12 OPS11 OPS10 Output Data 0 0 0 RX0 0 0 1 RX1 0 1 0 RX2 0 1 1 RX3 1 0 0 RX4 1 0 1 RX5 1 1 0 RX6 1 1 1 RX7 x x x DAUX Table 22. Output Data Select for TX1 MS0573-E-01 Default Default 2010/09 - 29 - [AK4115] ■ Bi-phase signal input circuit 0.1uF 75Ω Coax RX 75Ω AK4115 Figure 21. Consumer Input Circuit (Coaxial Input) Note: For coaxial input, if a coupling level to this input from the next RX input line pattern exceeds 50mV, there may be an incorrect operation. In this case, it is possible to lower the coupling level by adding this decoupling capacitor. Optical Receiver Optical Fiber 470 RX O/E AK4115 Figure 22. Consumer Input Circuit (Optical Input) 0.1uF RXP 110Ω Twisted Pair 110Ω 0.1uF RXN AK4115 Table 23. Professional Input Circuit (Balanced Input) Note. When RXN pin is unused, RXN pin must be AC-coupled to ground. For coaxial input in serial mode, the input level of RX line is small, so care must be taken to avoid crosstalk among the RX input lines. In this case, a shield is recommended between the input lines. In parallel mode, RX3-0 is available and RX7-4 change to other pins for audio format control. Those pins must be fixed to “H” or “L”. MS0573-E-01 2010/09 - 30 - [AK4115] ■ Bi-phase signal output circuit The AK4115 includes two TX output buffers. The output level is proportional to TVDD voltage. The T1 in Figure 23, Figure 24, Figure 25 and Figure 26 is a transformer of 1:1. The resistor values should use ±1% accuracy. 1. Line Driver of TX0 The output level of TX0 is 0.5V ± 20% using the external resistor network in consumer mode. R1 TX0 75Ω cable R2 TVSS TVDD R1 3.3V 240Ω 3.0V 220Ω 5.0V 430Ω T1 R2 150Ω 150Ω 150Ω Figure 23. TX0 External Resistor Network 1 Note: When the AK4115 is in the power-down mode (PDN pin = “L”), power supply current can be reduced by using an AC coupling capacitor as shown in Figure 24, since TX1 output is undetermined in power-down mode. 0.1uF R1 TX0 75Ω cable R2 TVDD R1 3.3V 240Ω 3.0V 220Ω 5.0V 430Ω TVSS T1 R2 150Ω 150Ω 150Ω Figure 24. TX0 External Resistor Network 2 2. Line Driver of TX1 2-1. Professional Mode (TVDD = 4.5V ∼ 5.5V) The TX1 has an RS422 line driver when TVDD is 5V±10%. The AES3 specification states that the line driver shall have a balanced output with an internal impedance of 110 ohms ±20% and also requires a balanced output drive capability of 2 to 7 volts peak-to-peak into 110 ohm load. The internal impedance of the RS422 driver along with a series resistors of 75 ohms realizes this requirement. 75Ω 0.1uF TXP1 110Ω cable TXN1 T1 Figure 25. Professional Output Driver Circuit MS0573-E-01 2010/09 - 31 - [AK4115] 2-2. Consumer Mode (TVDD = 2.7V ∼ 5.5V) For consumer use , the specifications require an output impedance of 75 ohms ±20% and a driver level of 0.5 ± 20% volts peak to peak. A combination of R1 in parallel with R2 meets this requirement. The outputs can be set to ground by resetting the device or a software mute. 0.1uF R1 TXP1 75Ω cable R2 TXN1 TVDD R1 3.3V 270Ω 3.0V 240Ω 5.0V 430Ω open T1 R2 150Ω 150Ω 150Ω Figure 26. Consumer Output Driver Circuit at AC coupling ■ PLL Loop Filter C1 and R should be connected in series and attached between FILT pin and AVSS in parallel with C2. The value of PLL Loop Filter includes temperature deviation. Be careful to minimize the noise into the FILT pin. When the Studio Sync mode is not used, FILT pin can be open. AK4115 FILT R C2 C1 AVSS Figure 27. PLL Loop Filter C1 [nF] C2 [pF] R [Ω] 24k ± 5% 10 ± 30% 100 ± 30% Table 24. Value of PLL Loop Filter MS0573-E-01 2010/09 - 32 - [AK4115] ■ Q-subcode buffers The AK4115 has a Q-subcode buffer for CD applications. The AK4115 takes the Q-subcode into registers by the following method. 1. The sync word (S0,S1) is constructed of at least 16 “0”s. 2. The start bit is “1”. 3. Those 7bits Q-W follows to the start bit. 4. The distance between two start bits are 8-16 bits. The QINT bit in the control register goes to “1” when the new Q-subcode differs from old one, and goes to “0” when the QINT bit is read. S0 S1 S2 S3 : S97 S0 S1 S2 S3 : 1 0 0 1 1 : 1 0 0 1 1 : 2 3 4 5 6 7 8 * 0 0 0 0 0 0 0 0… 0 0 0 0 0 0 0 0… Q2 R2 S2 T2 U2 V2 W2 0… Q3 R3 S3 T3 U3 V3 W3 0… : : : : : : : : Q97 R97 S97 T97 U97 V97 W97 0… 0 0 0 0 0 0 0 0… 0 0 0 0 0 0 0 0… Q2 R2 S2 T2 U2 V2 W2 0… Q3 R3 S3 T3 U3 V3 W3 0… : : : : : : : : ↑ Q Q2 Q3 Q4 CTRL Q5 Q6 Q7 Q8 ADRS (*) number of "0" : min=0; max=8. Figure 28. Configuration of U-bit(CD) Q9 Q10 Q11 Q12 Q13 Q14 Q15 Q16 Q17 Q18 Q19 Q20 Q21 Q22 Q23 Q24 Q25 TRACK NUMBER INDEX Q26 Q27 Q28 Q29 Q30 Q31 Q32 Q33 Q34 Q35 Q36 Q37 Q38 Q39 Q40 Q41 Q42 Q43 Q44 Q45 Q46 Q47 Q48 Q49 MINUTE SECOND FRAME Q50 Q51 Q52 Q53 Q54 Q55 Q56 Q57 Q58 Q59 Q60 Q61 Q62 Q63 Q64 Q65 Q66 Q67 Q68 Q69 Q70 Q71 Q72 Q73 ZERO ABSOLUTE MINUTE ABSOLUTE SECOND Q74 Q75 Q76 Q77 Q78 Q79 Q80 Q81 Q82 Q83 Q84 Q85 Q86 Q87 Q88 Q89 Q90 Q91 Q92 Q93 Q94 Q95 Q96 Q97 ABSOLUTE FRAME CRC G(x)=x^16+x^12+x^5+1 Figure 29. Q-subcode Addr Register Name 40H 41H 42H 43H 44H 45H 46H 47H 48H 49H Q-subcode Address / Control Q-subcode Track Q-subcode Index Q-subcode Minute Q-subcode Second Q-subcode Frame Q-subcode Zero Q-subcode ABS Minute Q-subcode ABS Second Q-subcode ABS Frame D7 D6 D4 D3 D2 D1 D0 Q9 Q8 ··· ··· Q17 Q16 ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· Q81 Q80 ··· ··· Figure 30. Q-subcode register ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· ··· Q3 Q11 ··· ··· ··· ··· ··· ··· ··· Q75 Q2 Q10 ··· ··· ··· ··· ··· ··· ··· Q74 MS0573-E-01 D5 2010/09 - 33 - [AK4115] ■ Error Handing for RX (PSEL = “0”) The followings nine events the INT0 and INT1 pins to trigger the interrupt condition. When the PLL is OFF (Clock Operation Mode 1), INT0 and INT1 pins go to “L”. 1. UNLCK : PLL unlock state detect “1” when the PLL loses lock. The AK4115 loses lock when the time between two preambles is not correct or when those preambles are not correct. 2. PAR : Parity error or bi-phase coding error detection “1” when parity error or bi-phase coding error is detected, updated every sub-frame cycle. 3. AUTO : Non-Linear PCM or DTS-CD Bit Stream detection The OR function of NPCM and DTSCD bits.is available at the AUTO bit. 4. VRX : Validity flag detection “1” when validity flag is detected. Updated every sub-frame cycle. 5. AUDION : Non-audio detection “1” when the “AUDION” bit in recovered channel status indicates “1”. Updated every block cycle. 6. STC : Sampling frequency or pre-emphasis information change detection When either FS3-0 bit or PEM bit is changed, it maintains “1” during 1 sub-frame. 7. QINT : U-bit Sync flag “1” when the Q-subcode differs from the old one. Updated every sync code cycle for Q-subcode. 8. CINT : Channel status sync flag “1” when received C bit differs from the old one. Updated every block cycle. 9. DAT : DAT Start ID detect “1” when the category code indicates “DAT” and “DAT Start ID” is detected. When DCNT bit is “1”, it does not indicate “1” even if “DAT Start ID” is detected again within “3841 x LRCK”. When “DAT Start ID” is detected again after “3840 x LRCK” passed, it indicates “1”. When DCNT bit is “0”, it indicates “1” every “DAT Start ID” detection. MS0573-E-01 2010/09 - 34 - [AK4115] 1. Parallel Mode In parallel mode, the INT0 pin outputs the ORed signal between UNLCK and PAR. The INT1 pin outputs the ORed signal between AUTO and AUDION. Once INT0 goes ”H”, it maintains “H” for 1024/fs cycles after all error events are removed. Table 25 shows the state of each output pins when the INT0/1 pin is “H”. Event Pin UNLCK PAR AUTO AUDION INT0 INT1 SDTO VOUT 1 x x x “L” “L” “H” Note 40 Previous Data 0 1 x x Output Output Output 0 0 x x “L” x x 1 x “H” Note 41 Note 42 Note 43 x x x 1 “L” x x 0 0 Note 40. INT1 pin outputs “L” or “H” in accordance with the ORed signal between AUTO and AUDION. Note 41. INT0 pin outputs “L” or “H” in accordance with the ORed signal between UNLCK and PAR. Note 42. SDTO pin outputs “L”, “Previous Data” or “Normal Data” in accordance with the ORed signal between UNLCK and PAR. Note 43. VOUT pin outputs “L” or “Normal operation” in accordance with the ORed signal between PAR and UNCLK. Table 25. Error Handling in parallel mode (x: Don’t care) 2. Serial Mode In serial mode, the INT1 and INT0 pins output an ORed signal based on the above nine interrupt events. When masked, the interrupt event does not affect the operation of the INT1-0 pins (the masks do not affect the registers in 07H and DAT bit). Once INT0 pin goes to “H”, it remains “H” for 1024/fs (this value can be changed by the EFH1-0 bits) after all events not masked by mask bits are cleared. INT1 pin immediately goes to “L” when those events are cleared. UNLCK, PAR, AUTO, AUDION and VRX bits in Address=07H indicate the interrupt status events above in real time. Once QINT, CINT and DAT bits go to “1”, it stays “1” until the register is read. When the AK4115 loses lock, the channel status bit, user bit, Pc and Pd are initialized. In this initial state, INT0 pin outputs the ORed signal between UNLCK and PAR bits. INT1 pin outputs the ORed signal between AUTO and AUDION bits. UNLCK 1 0 x Event Pin PAR Others SDTO VOUT x x “L” “L” 1 x Previous Data Output x x Output Output Table 26. Error Handling in serial mode (x: Don’t care) MS0573-E-01 TX Output Output Output 2010/09 - 35 - [AK4115] Error (UNLOCK, PAR,..) (Error) INT0 pin Hold Time (max: 4096/fs) INT1 pin Hold Time = 0 Register (PAR,CINT,QINT) Reset Hold “1” Register (others) Command MCKO,BICK,LRCK (UNLOCK) READ 07,08H Free Run (fs: around 6kHz) MCKO,BICK,LRCK (except UNLOCK) SDTO (UNLOCK) SDTO (PAR error) Previous Data SDTO (others) VOUT pin (UNLOCK) VOUT pin (except UNLOCK) Normal Operation Figure 31. INT0/1 pin timing MS0573-E-01 2010/09 - 36 - [AK4115] PDN pin ="L" to "H" Initialize Read (07H, 08H) INT0/1 pin ="H" No Yes Release Muting Mute DA C output Read (07H, 08H) (Each Error Handling) Read 07H, 08H (Res ets registers) No INT0/1 pin ="H" Yes Figure 32. Error Handling Sequence Example 1 MS0573-E-01 2010/09 - 37 - [AK4115] PDN pin ="L" to "H" Initialize Read (07H, 08H) No INT1 pin ="H" Yes Read (07H, 08H) and Detect QSUB= “1” (Read Q-buffer) QCRC = “0” No New data is invalid Yes INT1 pin ="L" No Yes New data is valid Figure 33. Error Handling Sequence Example (for Q/CINT) MS0573-E-01 2010/09 - 38 - [AK4115] ■ Error Handing for ELRCK (PSEL = “1”) The followings two events cause the INT0 and INT1 pins to show the status of the interrupt conditions. When the PLL is OFF (Clock Operation Mode 1), the INT0 and INT1 pins go to “L”. 1. UNLCK : PLL unlock state detect “1” when the PLL loses lock. The AK4115 loses lock when the phase difference between the current ELRCK and the previous ELRCK is more than 5% after “4 x fs”. The PLL is locked when the phase difference between the current ELRCK and the pervious ELRCK is less than 2% after “256 x fs”. When the PLL loses lock, the PLL goes to a free running state. The sampling frequency is typically 11kHz in this case. 2. FS3-0 : Sampling frequency detection FS3-0 bits are updated every “128 x fs”. When FS3-0 bits are changed, the STC bit is not changed and the INT0 and INT1 pins go to “H” after “1 x fs” In this mode, INT0 does not have the hold function. Therefore, INT0 and INT1 go to “L” at the same time when those events are removed. Each INT0/1 pins can mask those two events individually. 1. Parallel Mode In parallel mode, INT0 triggers UNLCK, and INT1 triggers when FS3-0 bits are changed. INT0 and INT1 go “L” after each event is removed. 2. Serial Mode In serial mode, INT1 and INT0 outputs an ORed signal based on the two interrupt events shown above. When masked, the interrupt event does not affect operation of the INT1-0. UNLCK 1 0 Event Pin Change of FS3-0 bits SDTO x “L” 1 Output Table 27. Error Handling (x: Don’t care) MS0573-E-01 TX Output Output 2010/09 - 39 - [AK4115] ■ Audio Serial Interface Format 1. LRCK, BICK, SDTO and DAUX In serial mode, the DIF2-0 bits can select eight serial audio data formats as shown in Table 28. In parallel mode, the DIF0 and DIF1 pins can select four serial audio data format as shown in Table 29. In Mode0-7, the serial data is MSB-first, 2's complement format. The SDTO is clocked out on the falling edge of BICK and DAUX is latched on the rising edge of BICK. BICK outputs 64fs clock in Mode 0-5. Mode 6-7 are Slave Modes, and BICK is available up to 128fs at fs=48kHz. If the data word length is equal or less than 20bit (Mode0-2), the LSBs in the sub-frame are truncated. In Mode 3-7, the last 4LSBs are auxiliary data (see Figure 34). When the Parity Error, Bi-phase Error or Frame Length Error occurs in a sub-frame, the AK4115 continues to output the last normal sub-frame data from SDTO repeatedly until the error is removed. When the Unlock Error occurs, AK4115 outputs “0” from SDTO. If DAUX is used, the data is transformed and outputted from SDTO. DAUX is used in Clock Operation Mode 1, 3 and unlock state of Mode 2. The input data format to DAUX should be left justified except in Mode5 and 7(Table 28). In Mode5 or 7, both the input data format of DAUX and output data format of SDTO are I2S. Mode 6 and 7 are Slave Modes that corresponds to the Master Mode of Mode4 and 5. In Slave Mode, LRCK and BICK should be synchronized with MCKO1/2. When AES3 bit is set to “1”, SDTO becomes AES3 mode. The serial data is LSB-first, 2’s complement format. The V, C, U and B bits behind the audio data are added. The B bit goes to “1” when the B-sync in preamble is detected (Figure 39). When DAUX is sent to SDTO, the data format depends on DIF0 bit. When DIF0 bit is set to “0”, the received MSB-first, 24bit MSB justified is converted to LSB-first, 24bit MSB justified. Then the only audio data is converted and V, U, C and B bits set to “0”. When DIF0 bit is set to “1”, the AES3 format received from DAUX pin is maintained and is sent to SDTO pin. Mode 8-9 support only synchronous mode (ASYNC bit = “0”). sub-frame of IEC958 0 3 4 preamble 7 8 11 12 27 28 29 30 31 Aux. V U C P LSB MSB MSB LSB 23 0 AK4115 Audio Data (MSB First) Figure 34. Bit configuration MS0573-E-01 2010/09 - 40 - [AK4115] Mode 0 1 2 3 4 5 6 7 8 9 AES3 bit 0 0 0 0 0 0 0 0 1 1 Mode 4 5 6 7 LRCK I/O H/L O H/L O H/L O H/L O H/L O L/H O H/L I L/H I H/L O H/L O DIF2 bit 0 0 0 0 1 1 1 1 0 0 DIF1 bit 0 0 1 1 0 0 1 1 0 0 DIF0 bit 0 1 0 1 0 1 0 1 0 1 DIF1 pin 0 0 1 1 DIF0 pin 0 1 0 1 LRCK I/O 24bit, Left justified 24bit, Left justified H/L O 24bit, I2S 24bit, I2S L/H O 24bit, Left justified 24bit, Left justified H/L I 24bit, I2S 24bit, I2S L/H I Table 29. Audio data format in parallel mode DAUX SDTO 24bit, Left justified 16bit, Right justified 24bit, Left justified 18bit, Right justified 24bit, Left justified 20bit, Right justified 24bit, Left justified 24bit, Right justified 24bit, Left justified 24bit, Left justified 24bit, I2S 24bit, I2S 24bit, Left justified 24bit, Left justified 24bit, I2S 24bit, I2S 24bit, Left justified AES3 Mode AES Mode AES3 Mode Table 28. Audio data format in serial mode DAUX BICK 64fs 64fs 64fs 64fs 64fs 64fs 64-128fs 64-128fs 64fs 64fs I/O O O O O O O I I O O BICK SDTO 64fs 64fs 64-128fs 64-128fs I/O O O I I 2. EMCK, ELRCK, EBICK and DAUX In asynchronous mode, the audio data format of DAUX is selected by EDIF1-0 bits. The clock source of master clock selects X’tal or EMCK by the MSEL bit. In parallel mode, this function is not supported. Mode EDIF1 bit 4 5 6 7 0 0 1 1 ELRCK EBICK I/O I/O 0 24bit, Left justified H/L O 64fs O 1 24bit, I2S L/H O 64fs O 0 24bit, Left justified H/L I 64-128fs I 1 24bit, I2S L/H I 64-128fs I Table 30. Audio data format in asynchronous mode EDIF0 bit DAUX Default In asynchronous mode, the frequecny of EMCK/X’tal selects 128fs, 256fs or 512fs. It is controlled by ECKS1-0 bit. ECKS1 0 0 1 1 ECKS0 EMCK Frequency 0 512fs 1 256fs 0 128fs 1 N/A Table 31. EMCK Frequency MS0573-E-01 fs(max) 54kHz 108kHz 216kHz - Default 2010/09 - 41 - Default [AK4115] LRCK(0) 0 1 2 15 16 17 31 0 1 2 15 16 17 31 0 1 BICK (0:64fs) 15 14 1 0 15 14 1 0 SDTO(0) 15:MSB, 0:LSB Rch Data Lch Data Figure 35. Mode 0 Timing LRCK(0) 0 1 2 9 10 12 11 31 0 1 2 9 10 11 12 31 0 1 0 1 BICK (0:64fs) 23 22 21 20 1 0 23 22 21 20 1 0 SDTO(0) 23:MSB, 0:LSB Rch Data Lch Data Figure 36. Mode 3 Timing LRCK ELRCK BICK EBICK (64fs) 0 1 23 SDTO(0) DAUX(I) 2 21 22 21 22 2 1 31 24 23 0 0 1 2 23 22 21 3 22 2 23 1 24 31 0 23 22 23:MSB, 0:LSB Lch Data Rch Data Figure 37. Mode 4, 6 Timing Mode4 : LRCK, BICK, ELRCK, EBICK : Output Mode6 : LRCK, BICK, ELRCK, EBICK: Input LRCK ELRCK BICK EBICK (64fs) SDTO(0) DAUX(I) 0 1 2 22 23 22 21 24 23 2 1 25 31 0 1 2 23 22 0 21 22 3 23 2 1 24 25 0 31 0 1 23 23:MSB, 0:LSB Lch Data Rch Data Figure 38. Mode 5, 7 Timing MS0573-E-01 Mode5 : LRCK, BICK, ELRCK, EBICK : Output Mode7 : LRCK, BICK, ELRCK, EBICK : Input 2010/09 - 42 - [AK4115] LRCK(o) 0 1 2 24 25 27 26 28 31 0 1 2 24 25 26 27 31 28 0 1 BICK(o) (64fs) SDTO(0) DAUX(I) 0 1 2 23 V U C 0 B 1 2 23 V U C B 0 1 23:MSB, 0:LSB V: Validity, C: C-bit, U:U-bit, B:B sync Rch Data Lch Data Figure 39. AES3 Mode ■ Serial Control Interface 1. 4-wire serial control mode (IIC pin = “L”) The internal registers may be either written or read by the 4-wire μP interface pins: CSN, CCLK, CDTI & CDTO. The data on this interface consists of Chip address (2-bits, C1-0 are fixed to “00”), Read/Write (1bit), Register address (MSB first, 8-bits) and Control data (MSB first, 8-bits). Address and data is clocked in on the rising edge of CCLK and data is clocked out on the falling edge. For write operations, data is latched after the 24th rising edge of CCLK, after a high-to-low transition of CSN. For read operations, the CDTO output goes high impedance after a low-to-high transition of CSN. The maximum speed of CCLK is 5MHz. PDN pin = “L” resets the registers to their default values. When the state of P/SN pin is changed, the AK4115 should be reset by PDN pin = “L”. CSN should be brought “H” after each word. CSN 0 1 7 8 2 3 4 5 6 0 0 0 0 0 R/W A7 9 10 11 12 13 14 15 16 A6 A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 A6 A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 17 18 19 20 21 22 23 CCLK CDTI WRITE C1 C0 Hi-Z CDTO CDTI READ CDTO C1 C0 0 0 0 0 0 R/W A7 Hi-Z C1-C0: R/W: A7-A0: D7-D0: D7 D6 D5 D4 D3 D2 D1 D0 Hi-Z Chip Address (Fixed to “00”) READ/WRITE (0:READ, 1:WRITE) Register Address Control Data Figure 40. 4-wire Serial Control I/F Timing MS0573-E-01 2010/09 - 43 - [AK4115] 2. I2C bus control mode (IIC pin = “H”) AK4115 supports a fast-mode I2C-bus system (max : 400kHz). 2-1. Data transfer All commands are preceded by a START condition. After the START condition, a slave address is sent. After the AK4115 recognizes the START condition, the device interfaced to the bus waits for the slave address to be transmitted over the SDA line. If the transmitted slave address matches an address for one of the devices, the designated slave device pulls the SDA line to LOW (ACKNOWLEDGE). The data transfer is always terminated by a STOP condition generated by the master device. 2-1-1. Data validity The data on the SDA line must be stable during the HIGH period of the clock. The HIGH or LOW state of the data line can only change when the clock signal on the SCL line is LOW except for the START and the STOP condition. SCL SDA DATA LINE STABLE : DATA VALID CHANGE OF DATA ALLOWED Figure 41. Data transfer 2-1-2. START and STOP condition A HIGH to LOW transition on the SDA line while SCL is HIGH indicates a START condition. All sequences start from the START condition. A LOW to HIGH transition on the SDA line while SCL is HIGH defines a STOP condition. All sequences end by the STOP condition. SCL SDA START CONDITION STOP CONDITION Figure 42. START and STOP conditions MS0573-E-01 2010/09 - 44 - [AK4115] 2-1-3. ACKNOWLEDGE ACKNOWLEDGE is a software convention used to indicate successful data transfers. The transmitting device will release the SDA line (HIGH) after transmitting eight bits. The receiver must pull down the SDA line during the acknowledge clock pulse so that that it remains stable “L” during “H” period of this clock pulse. The AK4115 will generates an acknowledge after each byte has been received. In the read mode, the slave, AK4115 will transmit eight bits of data, release the SDA line and monitor the line for an acknowledge. If an acknowledge is detected and no STOP condition is generated by the master, the slave will continue to transmit data. If an acknowledge is not detected, the slave will terminate further data transmissions and await the STOP condition. Clock pulse for acknowledge SCL FROM MASTER 1 8 9 DATA OUTPUT BY TRANSMITTER not acknowledge DATA OUTPUT BY RECEIVER START CONDITION acknowledge Figure 43. Acknowledge on the I2C-bus 2-1-4. FIRST BYTE The first byte, which includes seven bits of slave address and one bit of R/W bit, is sent after the START condition. If the transmitted slave address matches an address for one of the device, the receiver who has been addressed pulls down the SDA line. The most significant five bits of the slave address are fixed as “00100”. The next two bits are CAD1 and CAD0 (device address bits). These two bits identify the specific device on the bus. The hard-wired input pins (CAD1 pin and CAD0 pin) set them. The eighth bit (LSB) of the first byte (R/W bit) defines whether a write or read condition is requested by the master. A “1” indicates that the read operation is to be executed. A “0” indicates that the write operation is to be executed. 0 0 1 0 0 CAD1 CAD0 R/W (Those CAD1/0 should match with CAD1/0 pins.) Figure 44. The First Byte MS0573-E-01 2010/09 - 45 - [AK4115] 2-2. WRITE Operations Set R/W bit = “0” for the WRITE operation of AK4115. After receipt the start condition and the first byte, the AK4115 generates an acknowledge, and awaits the second byte (register address). The second byte consists of the address for control registers of AK4115. The format is MSB first, 8-bits. A7 A6 A5 A4 A3 A2 A1 A0 Figure 45. The Second Byte After receipt of the second byte, the AK4115 generates an acknowledge, and awaits the third byte. Those data after the second byte contain control data. The format is MSB first, 8-bits. D7 D6 D5 D4 D3 D2 D1 D0 Figure 46. Byte structure after the second byte The AK4115 is capable of more than one byte write operation by one sequence. After receipt of the third byte, the AK4115 generates an acknowledge, and awaits the next data again. The master can transmit more than one word instead of terminating the write cycle after the first data word is transferred. After the receipt of each data, the internal 5-bit address counter is incremented by one, and the next data is taken into next address automatically. If the address exceed 49H prior to generating the stop condition, the address counter will “roll over” to 00H and the previous data will be overwritten. S T A R T SDA Register Address(n) Slave Address S T Data(n+x) O P Data(n+1) Data(n) P S A C K A C K A C K A C K Figure 47. WRITE Operation MS0573-E-01 2010/09 - 46 - [AK4115] 2-3. READ Operations Set R/W bit = “1” for the READ operation of AK4115. After transmission of a data, the master can read next address’s data by generating the acknowledge instead of terminating the write cycle after the receipt the first data word. After the receipt of each data, the internal 5-bit address counter is incremented by one, and the next data is taken into next address automatically. If the address exceed 49H prior to generating the stop condition, the address counter will “roll over” to 00H and the previous data will be overwritten. The AK4115 supports two basic read operations: CURRENT ADDRESS READ and RANDOM READ. 2-3-1. CURRENT ADDRESS READ The AK4115 contains an internal address counter that maintains the address of the last word accessed, incremented by one. Therefore, if the last access (either a read or write) was to address n, the next CURRENT READ operation would access data from the address n+1. After receipt of the slave address with R/W bit set to “1”, the AK4115 generates an acknowledge, transmits 1byte data which address is set by the internal address counter and increments the internal address counter by 1. If the master does not generate an acknowledge to the data but generate the stop condition, the AK4115 discontinues transmission. S T A R T SDA Slave Address Data(n) Data(n+1) S Data(n+x) T O P Data(n+2) P S A C K A C K A C K A C K Figure 48. CURRENT ADDRESS READ 2-3-2. RANDOM READ Random read operation allows the master to access any memory location at random. Prior to issuing the slave address with the R/W bit set to “1”, the master must first perform a “dummy” write operation. The master issues the start condition, slave address(R/W=“0”) and then the register address to read. After the register address’s acknowledge, the master immediately reissues the start condition and the slave address with the R/W bit set to “1”. Then the AK4115 generates an acknowledge, 1byte data and increments the internal address counter by 1. If the master does not generate an acknowledge to the data but generate the stop condition, the AK4115 discontinues transmission. S T A R T SDA Slave Address S T A R T Word Address(n) S Slave Address Data(n) S Data(n+x) T O P Data(n+1) P S A C K A C K A C K A C K A C K Figure 49. RANDOM READ MS0573-E-01 2010/09 - 47 - [AK4115] ■ Register Map Addr Register Name D7 D6 D5 D4 D3 D2 D1 D0 00H CLK & Power Down Control CS12 BCU CM1 CM0 OCKS1 OCKS0 PWN RSTN 01H Format & De-em Control AES3 DIF2 DIF1 DIF0 DEAU DEM1 DEM0 ACKS 02H Input/ Output Control 0 TX1E OPS12 OPS11 OPS10 TX0E OPS02 OPS01 OPS00 03H Input/ Output Control 1 EFH1 EFH0 UDIT BCU_IO DIT IPS2 IPS1 IPS0 04H INT0 MASK MQIT0 MAUT0 MCIT0 MULK0 MV0 MSTC0 MAUD0 MPAR0 05H INT1 MASK MQIT1 MAUT1 MCIT1 MULK1 MV1 MSTC1 MAUD1 MPAR1 06H DAT Mask & DTS Detect DIV XMCK FAST DCNT DTS16 DTS14 07H Receiver Status 0 QINT AUTO CINT UNLCK VRX STC AUDION PAR 08H Receiver Status 1 FS3 FS2 FS1 FS0 PEM DAT DTSCD NPCM 0 0 0 0 09H Receiver Status 2 0 0 0AH Clock Control TX1NE 0 0BH TX Control MSEL 0CH RX Channel Status Byte 0 • 23H • RX Channel Status Byte 23 24H MDAT1 MDAT0 QCRC CCRC MCK2E MCK1E ASYNC WSYNC XSEL PSEL ECKS1 ECKS0 EDIF1 EDIF0 CTRAN CCRE VTX CR7 CR6 CR5 CR4 CR3 CR2 CR1 CR0 • • • • • • • • CR191 CR190 CR189 CR188 CR187 CR186 CR185 CR184 TX Channel Status Byte 0 CT7 CT6 CT5 CT4 CT3 CT2 CT1 CT0 • 3BH • TX Channel Status Byte 23 • CT191 • CT190 • CT189 • CT188 • CT187 • CT186 • CT185 • CT184 3CH Burst Preamble Pc Byte 0 PC7 PC6 PC5 PC4 PC3 PC2 PC1 PC0 3DH Burst Preamble Pc Byte 1 PC15 PC14 PC13 PC12 PC11 PC10 PC9 PC8 3EH Burst Preamble Pd Byte 0 PD7 PD6 PD5 PD4 PD3 PD2 PD1 PD0 3FH Burst Preamble Pd Byte 1 PD15 PD14 PD13 PD12 PD11 PD10 PD9 PD8 40H Q-subcode Address / Control Q9 Q8 Q7 Q6 Q5 Q4 Q3 Q2 41H Q-subcode Track Q17 Q16 Q15 Q14 Q13 Q12 Q11 Q10 42H Q-subcode Index Q25 Q24 Q23 Q22 Q21 Q20 Q19 Q18 43H Q-subcode Minute Q33 Q32 Q31 Q30 Q29 Q28 Q27 Q26 44H Q-subcode Second Q41 Q40 Q39 Q38 Q37 Q36 Q35 Q34 45H Q-subcode Frame Q49 Q48 Q47 Q46 Q45 Q44 Q43 Q42 46H Q-subcode Zero Q57 Q56 Q55 Q54 Q53 Q52 Q51 Q50 47H Q-subcode ABS Minute Q65 Q64 Q63 Q62 Q61 Q60 Q59 Q58 48H Q-subcode ABS Second Q73 Q72 Q71 Q70 Q69 Q68 Q67 Q66 49H Q-subcode ABS Frame Q81 Q80 Q79 Q78 Q77 Q76 Q75 Q74 4AH Optional Control 0 0 0 0 0 0 CTX 0 Notes: When PDN pin goes “L”, the registers are initialized to their default values. When RSTN bit goes “0”, the internal timing is reset and the registers are initialized to their default values. All data can be written to the register even if PWN bit is “0”. Data must not be written to addresses 4BH through FFH. MS0573-E-01 2010/09 - 48 - [AK4115] ■ Register Definitions Reset & Initialize Addr Register Name 00H CLK & Power Down Control R/W Default D7 CS12 R/W 0 D6 BCU R/W 1 D5 CM1 R/W 0 D4 CM0 R/W 0 D3 D2 OCKS1 OCKS0 R/W R/W 0 0 D1 PWN R/W 1 D0 RSTN R/W 1 RSTN: Timing Reset & Register Initialize 0: Reset & Initialize 1: Normal Operation (Default) PWN: Power Down 0: Power Down 1: Normal Operation (Default) OCKS1-0: Master Clock Frequency Select (See Table 9) CM1-0: Master Clock Operation Mode Select (See Table 3 and Table 5) BCU: Block start & C/U Output Mode when BCU_IO bit is “1” 0: B, C and U pins output “L”. 1: B, C, and U pins output the data recovered from biphase signal. (Default) When BCU_IO bit is “0”, BCU bit is ignored. CS12: Channel Status Select 0: Channel 1 (Default) 1: Channel 2 Selects which channel status is used to derive C-bit buffers, AUDION, PEM, FS3, FS2, FS1, FS0, Pc and Pd. The de-emphasis filter is controlled by channel 1 in the Parallel Mode. Format & De-emphasis Control Addr Register Name 01H Format & De-em Control R/W Default D7 AES3 R/W 0 D6 DIF2 R/W 1 D5 DIF1 R/W 1 D4 DIF0 R/W 0 D3 DEAU R/W 1 D2 DEM1 R/W 0 D1 DEM0 R/W 1 D0 ACKS R/W 0 ACKS: Master clock Auto Setting Mode 0: Disable (Default) 1: Enable DEM1-0: 32, 44.1, 48kHz De-emphasis Control (See Table 18) DEAU: De-emphasis Auto Detect Enable 0: Disable 1: Enable (Default) DIF2-0, AES3: Audio Data Format Control (See Table 28) MS0573-E-01 2010/09 - 49 - [AK4115] Input/Output Control Addr Register Name 02H Input/ Output Control 0 R/W Default D7 TX1E R/W 1 D6 D5 D4 OPS12 OPS11 OPS10 R/W R/W R/W 0 0 0 D3 TX0E R/W 1 D2 D1 D0 OPS02 OPS01 OPS00 R/W R/W R/W 0 0 0 OPS02-00: Output Through Data Select for TX0 pin (See Table 21) TX0E: TX0 Output Enable 0: Disable. TX0 outputs “L”. 1: Enable (Default) OPS12-10: Output Through Data Select for TX1 pin (See Table 22) TX1E: TXP1/TXN1 pins Output Enable 0: Disable. TXP1 pin outputs “L”. TXN1 pin outputs “H”. 1: Enable (Default) Addr Register Name 03H Input/ Output Control 1 R/W Default D7 EFH1 R/W 0 D6 EFH0 R/W 1 D5 D4 UDIT BCU_IO R/W R/W 0 1 D3 DIT R/W 1 D2 IPS2 R/W 0 D1 IPS1 R/W 0 D0 IPS0 R/W 0 IPS2-0: Input Recovery Data Select (See Table 19) DIT: Through data/Transmit data select for TXP1/N1 pins 0: Through data (RX data). 1: Transmit data (DAUX data). (Default) BCU_IO: Select I/O of B, C and U pins 0: Input 1: Output (Default) UDIT: U bit control for DIT 0: U bit is fixed to “0”. (Default) 1: Recovered U bit is used for DIT (loop mode for U bit) EFH1-0: Interrupt 0 Pin Hold Count Select 00: 512 LRCK 01: 1024 LRCK (Default) 10: 2048 LRCK 11: 4096 LRCK MS0573-E-01 2010/09 - 50 - [AK4115] Mask Control for INT0 Addr Register Name 04H INT0 MASK R/W Default D7 D6 D5 D4 D3 D2 D1 D0 MQIT0 MAUT0 MCIT0 MULK0 MVRX0 MSTC0 MAUD0 MPAR0 R/W R/W R/W R/W R/W R/W R/W R/W 1 1 1 0 1 1 1 0 MPAR0: Mask enable for PAR bit 0: Mask disable (Default) 1: Mask enable MAUD0:Mask enable for AUDION bit 0: Mask disable 1: Mask enable (Default) MSTC0: Mask enable for STC bit 0: Mask disable 1: Mask enable (Default) MVRX0:Mask enable for VRX bit 0: Mask disable 1: Mask enable (Default) MULK0:Mask enable for UNLCK bit 0: Mask disable (Default) 1: Mask enable MCIT0: Mask enable for CINT bit 0: Mask disable 1: Mask enable (Default) MAUT0:Mask enable for AUTO bit 0: Mask disable 1: Mask enable (Default) MQIT0: Mask enable for QINT bit 0: Mask disable 1: Mask enable (Default) When mask is set to “1”, corresponding event does not affect INT0 pin operation. MS0573-E-01 2010/09 - 51 - [AK4115] Mask Control for INT1 Addr Register Name 05H INT1 MASK R/W Default D7 D6 D5 D4 D3 D2 D1 D0 MQIT1 MAUT1 MCIT1 MULK1 MVRX1 MSTC1 MAUD MPAR1 R/W R/W R/W R/W R/W R/W R/W R/W 1 0 1 1 1 1 0 1 MPAR1: Mask enable for PAR bit 0: Mask disable 1: Mask enable (Default) MAUD1:Mask enable for AUDION bit 0: Mask disable (Default) 1: Mask enable MSTC1: Mask enable for STC bit 0: Mask disable 1: Mask enable (Default) MVRX1:Mask enable for VRX bit 0: Mask disable 1: Mask enable (Default) MULK1:Mask enable for UNLCK bit 0: Mask disable 1: Mask enable (Default) MCIT1: Mask enable for CINT bit 0: Mask disable 1: Mask enable (Default) MAUT1:Mask enable for AUTO bit 0: Mask disable (Default) 1: Mask enable MQIT1: Mask enable for QINT bit 0: Mask disable 1: Mask enable (Default) When mask is set to “1”, corresponding event does not affect INT1 pin operation. MS0573-E-01 2010/09 - 52 - [AK4115] DAT Mask & DTS Detect Addr Register Name 06H DAT Mask & DTS Detect R/W Default D7 DIV R/W 0 D6 XMCK R/W 0 D5 FAST R/W 0 D4 DCNT R/W 1 D3 DTS16 R/W 1 D2 D1 D0 DTS14 MDAT1 MDAT0 R/W R/W R/W 1 1 1 MDAT0: Mask enable for DAT bit 0: Mask disable 1: Mask enable (Default) The factor which mask bit is set to “0” affects INT0 pin operation. MDAT1: Mask enable for DAT bit 0: Mask disable 1: Mask enable (Default) The factor which mask bit is set to “0” affects INT1 pin operation. DTS14: DTS-CD 14bit Sync Word Detect 0: Disable 1: Enable (Default) DTS16: DTS-CD 16bit Sync Word Detect 0: Disable 1: Enable (Default) DCNT: DAT Start ID Counter 0: Disable 1: Enable (Default) FAST: Select PLL Lock Time when the biphase signal is recovered. 0: ≤ (20ms + 384/fs) (Default) 1: ≤ (20ms + 1/fs) XMCK: Select output frequency of MCKO2 (See Table 10) 0: Depends on CM1-0 bits and OCKS1-0 bits (Default) 1: Fixed to X’tal Mode DIV: MCKO2 Output Frequency Select at X’tal Mode (See Table 10) 0: Same frequency as X’tal (Default) 1: Half frequency of X’tal MS0573-E-01 2010/09 - 53 - [AK4115] Receiver Status 0 Addr Register Name 07H Receiver status 0 R/W Default D7 QINT RD 0 D6 AUTO RD 0 D5 CINT RD 0 D4 UNLCK RD 0 D3 VRX RD 0 D2 STC RD 0 D1 AUDION RD 0 D0 PAR RD 0 PAR: Parity Error or Bi-phase Error Status 0: No Error 1: Error This bit goes to “1”, if a Parity Error or Biphase Error is detected in the sub-frame. AUDION: Audio Bit Output 0: Audio 1: Non Audio This bit is made by encoding channel status bits. STC: Sampling Frequency or Pre-emphasis Information Change Detection 0: No detect 1: Detect This bit goes to “1” when either the FS3-0 or PEM bit changes. VRX: Validity of channel status for RX 0: Valid 1: Invalid UNLCK: PLL Lock Status 0: Lock 1: Unlock CINT: Channel Status Buffer Interrupt 0: No change 1: Changed This bit goes to “1” when C-bit stored in register addresses 0CH to 24H changes. AUTO: Non-PCM Auto Detect 0: No detect 1: Detect QINT: Q-subcode Buffer Interrupt 0: No change 1: Changed This bit goes to “1” when Q-subcode stored in register addresses 40H to 49H changes. STC, QINT, CINT and PAR bits are initialized when 07H is read. MS0573-E-01 2010/09 - 54 - [AK4115] Receiver Status 1 Addr Register Name 08H Receiver status 1 R/W Default D7 FS3 RD 0 D6 FS2 RD 0 D5 FS1 RD 0 D4 FS0 RD 1 D3 PEM RD 0 D2 DAT RD 0 D1 DTSCD RD 0 D0 NPCM RD 0 D3 0 RD 0 D2 0 RD 0 D1 QCRC RD 0 D0 CCRC RD 0 NPCM: Non-PCM Bit Stream Auto Detection 0: No detect 1: Detect DTSCD: DTS-CD Bit Stream Auto Detection 0: No detect 1: Detect DAT: DAT Start ID Detect 0: No detect 1: Detect DAT bit is initialized when 08H is read. PEM: Pre-emphasis Detect 0: OFF 1: ON This bit is made by encoding channel status bits. FS3-0: Sampling Frequency detection (See Table 14) Receiver Status 1 Addr Register Name 09H Receiver status 1 R/W Default D7 0 RD 0 D6 0 RD 0 D5 0 RD 0 D4 0 RD 0 CCRC: Cyclic Redundancy Check for Channel Status 0: No error 1: Error This bit is enabled only in professional mode and only for the channel selected by the CS12 bit. QCRC: Cyclic Redundancy Check for Q-subcode 0: No error 1: Error MS0573-E-01 2010/09 - 55 - [AK4115] Clock Control Addr Register Name 0AH Clock Control R/W Default D7 TX1NE R/W 1 D6 0 RD 0 D5 D4 D3 D2 MCK2E MCK1E ASYNC WSYNC R/W R/W R/W R/W 1 1 0 0 D1 XSEL R/W 0 D0 PSEL R/W 0 D1 CCRE R/W 1 D0 VTX R/W 0 PSEL: Setting of PLL reference clock (See Table 1) XSEL: Setting of X’tal oscillator (See Table 12) WSYNC: Synchronization between the biphase signal and ELRCK 0: Disable (Default) 1: Enable ASYNC: Setting of synchronous / asynchronous mode for DIT/DIR 0: Synchronous mode (Default) 1: Asynchronous mode MCK1E: Setting of MCKO1 output 0: Disable. Output “L”. 1: Enable (Default) MCK2E: Setting of MCKO2 output 0: Disable. Output “L”. 1: Enable (Default) TX1NE: Setting of TXN1 pin. 0: Disable. Output “L”. This mode is useful for consumer. 1: Enable (Default) TX Control Addr Register Name 0BH TX Control R/W Default D7 MSEL RD 0 D6 ECKS1 RD 0 D5 ECKS0 R/W 1 D4 EDIF1 R/W 1 D3 EDIF0 R/W 0 D2 CTRAN R/W 0 VTX: Setting of Validity bit for TX 0: Valid (Default) 1: Invalid CCRE: CCRC Enable at professional mode 0: CCRC data is not generated. 1: CCRC data is generated in professional mode. In consumer mode, CCRC data is not generated. (Default) CTRAN: Transfer mode of CR191-0 bits 0: Not transfer or finish to transfer (Default) 1: Transfer All CR191-0 bits is transferred to CT191-0 bits when CTRAN bit changes “0” to “1”. The transferred CT191-0 bits are valid after next block start signal is detected. CTRAN bit goes to “0” after finishing the transfer. EDIF1-0: Setting of audio interface mode in asynchronous mode. (See Table 30) ECK1-0: Setting of EMCK input frequency (See Table 31) MSEL: Master clock setting for TX in asynchronous mode (See Table 4) MS0573-E-01 2010/09 - 56 - [AK4115] Receiver Channel Status Addr Register Name 0CH RX Channel Status Byte 0 • • 23H RX Channel Status Byte 23 R/W Default D7 D6 D5 D4 D3 D2 D1 D0 CR7 CR6 CR5 CR4 CR3 CR2 CR1 CR0 • • • • • • • • CR191 CR190 CR189 CR188 CR187 CR186 CR185 CR184 RD Not initialized CR191-0: Receiver Channel Status Byte 23-0 Transmitter Channel Status Addr Register Name 24H TX Channel Status Byte 0 R/W Default 25H TX Channel Status Byte 1 • • 3BH TX Channel Status Byte 23 R/W Default D7 CT7 D6 CT6 D5 CT5 0 CT15 • CT191 0 CT14 • CT190 0 CT13 • CT189 D4 CT4 D3 CT3 R/W 0 0 CT12 CT11 • • CT188 CT187 R/W 0 D2 CT2 D1 CT1 D0 CT0 1 CT10 • CT186 0 CT9 • CT185 0 CT8 • CT184 D2 PC2 PC10 PD2 PD10 D1 PC1 PC9 PD1 PD9 D0 PC0 PC8 PD0 PD8 CT7-0: Transmitter Channel Status Byte 0 Default: “00000100” CT191-8: Transmitter Channel Status Byte 23-1 Default: “00000000” Burst Preamble Pc/Pd in non-PCM encoded Audio Bitstreams Addr 3CH 3DH 3EH 3FH Register Name Burst Preamble Pc Byte 0 Burst Preamble Pc Byte 1 Burst Preamble Pd Byte 0 Burst Preamble Pd Byte 1 R/W Default D7 PC7 PC15 PD7 PD15 D6 PC6 PC14 PD6 PD14 D5 PC5 PC13 PD5 PD13 D4 PC4 PC12 PD4 PD12 D3 PC3 PC11 PD3 PD11 RD Not initialized PC15-0: Burst Preamble Pc Byte 0 and 1 PD15-0: Burst Preamble Pd Byte 0 and 1 MS0573-E-01 2010/09 - 57 - [AK4115] Q-subcode Buffer Addr 40H 41H 42H 43H 44H 45H 46H 47H 48H 49H Register Name Q-subcode Address / Control Q-subcode Track Q-subcode Index Q-subcode Minute Q-subcode Second Q-subcode Frame Q-subcode Zero Q-subcode ABS Minute Q-subcode ABS Second Q-subcode ABS Frame R/W Default D7 Q9 Q17 Q25 Q33 Q41 Q49 Q57 Q65 Q73 Q81 D6 Q8 Q16 Q24 Q32 Q40 Q48 Q56 Q64 Q72 Q80 D5 Q7 Q15 Q23 Q31 Q39 Q47 Q55 Q63 Q71 Q79 D4 Q6 Q14 Q22 Q30 Q38 Q46 Q54 Q62 Q70 Q78 D3 Q5 Q13 Q21 Q29 Q37 Q45 Q53 Q61 Q69 Q77 D2 Q4 Q12 Q20 Q28 Q36 Q44 Q52 Q60 Q68 Q76 D1 Q3 Q11 Q19 Q27 Q35 Q43 Q51 Q59 Q67 Q75 D0 Q2 Q10 Q18 Q26 Q34 Q42 Q50 Q58 Q66 Q74 RD Not initialized Optional Control Addr Register Name 4AH Optional Control R/W Default D7 0 RD 0 D6 0 RD 0 D5 0 RD 0 D4 0 RD 0 D3 0 RD 0 D2 0 RD 0 D1 CTX R/W 0 D0 0 RD 0 CTX: Setting of channel status information for AES3 mode 0: Channel status information on DAUX is sent from TX (Default) 1: Channel status information in control registers (CTX191-0 bits) is sent from TX. MS0573-E-01 2010/09 - 58 - [AK4115] ■ Burst Preambles in non-PCM Bitstreams sub-frame of IEC958 0 3 4 preamble 7 8 Aux. 11 12 27 28 29 30 31 LSB MSB V U C P 16 bits of bitstream 0 Pa Pb Pc Pd 15 Burst_payload stuffing repetition time of the burst Figure 50. Data structure in IEC60958 Preamble word Pa Pb Pc Pd Length of field Contents 16 bits sync word 1 16 bits sync word 2 16 bits Burst info 16 bits Length code Table 32. Burst preamble words Bits of Pc Value Contents 0-4 data type NULL data Dolby AC-3 data reserved PAUSE MPEG-1 Layer1 data MPEG-1 Layer2 or 3 data or MPEG-2 without extension MPEG-2 data with extension MPEG-2 AAC ADTS MPEG-2, Layer1 Low sample rate MPEG-2, Layer2 or 3 Low sample rate reserved DTS type I DTS type II DTS type III ATRAC ATRAC2/3 reserved reserved, shall be set to “0” error-flag indicating a valid burst_payload error-flag indicating that the burst_payload may contain errors data type dependent info bit stream number, shall be set to “0” Table 33. Fields of burst info Pc 5, 6 7 8-12 13-15 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16-31 0 0 1 0 Value 0xF872 0x4E1F see Table 33 numbers of bits Repetition time of burst in IEC60958 frames MS0573-E-01 ≤4096 1536 384 1152 1152 1024 384 1152 512 1024 2048 512 1024 2010/09 - 59 - [AK4115] ■ Non-PCM Bitstream timing 1) When Non-PCM preamble is not coming within 4096 frames, PDN pin Bit stream Pa Pb Pc1 Pd1 Pa Pb Pc2 Pd2 Repetition time Pa Pb Pc3 Pd3 >4096 frames AUTO bit Pc Register “0” Pd Register “0” Pc1 Pc2 Pd1 Pc3 Pd2 Pd3 Figure 51. Timing example 1 2) When Non-PCM bitstream stops (when MULK0=0), INT0 hold time INT0 pin < PLL Lock time Bit stream Pa Pb Pc1 Pd1 Stop Pa Pb Pcn Pdn 2~3 Syncs (B,M or W) <Repetition time AUTO bit Pc Register Pd Register Pc0 Pc1 Pd0 Pcn Pd1 Pdn Figure 52. Timing example 2 MS0573-E-01 2010/09 - 60 - [AK4115] SYSTEM DESIGN Figure 53 shows the example of system connection diagram for 4-wire serial mode. 3.3V S/PDIF Sources C1: 0.1μ C2: 10μ C2 + C1 4.7μ C1 C1 S/PDIF Sources 59 58 57 56 55 54 RX4 RX3 AVSS RX2 AVDD RX1 AVSS RXP0 RXN0 ACKS 10kΩ 53 52 51 50 49 R 60 AVSS 61 VCOM 62 P/SN 63 AVDD 64 AVDD + 10n 1 RX5 FILT 48 2 TEST(AVSS) XTL1 47 3 RX6 XTL0 46 4 PDN PSEL 45 5 RX7 100p 24kΩ IIC 44 C2 C1 3.3V + 6 DVDD BVSS 43 7 VIN DVSS 42 8 DAUX DVDD 41 C1 + Top View 9 DVSS C2 3.3V CSN 40 10 MCKO1 CCLK 39 11 MCKO2 CDTI 38 uP DSP1 12 OVDD CDTO 37 13 OVSS INT1 36 C1 INT0 35 14 BICK VOUT TVDD TX0 TXP1 TXN1 TVSS XTI1 XTO1 XTI2 XTO2 OVDD OVSS EBICK EMCK 33 U 16 LRCK C ELRCK 34 B 15 SDTO 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 DSP2 C1 C1 + + uP C C2 C C C2 C S/PDIF out 5V 3.3V Figure 53. Typical Connection Diagram (4-wire serial mode) Notes: - For setting of XTL0 and XTL1, refer the Table 13. - “C” depends on the crystal. - AVSS, BVSS, TVSS, OVSS and DVSS must be connected the same ground plane. - Digital signals, especially clocks, should be kept away from the R and FILT pins in order to avoid an effect to the clock jitter performance. MS0573-E-01 2010/09 - 61 - [AK4115] PACKAGE 64pin LQFP(Unit: mm) 12.0 Max 1.85 10.0 1.40 0.00~0.25 33 32 48 12.0 49 64 17 16 1 0.5 0.2±0.1 0.09~0.25 0.10 M 0°~10° 0.50±0.25 0.10 ■ Material & Lead finish Package molding compound: Epoxy Lead frame material: Cu Lead frame surface treatment: Solder (Pb free) plate MS0573-E-01 2010/09 - 62 - [AK4115] MARKING AKM AK4115VQ XXXXXXX 1 XXXXXXX: Date code identifier REVISION HISTORY Date (YY/MM/DD) 06/12/13 10/09/28 Revision 00 01 Reason First Edition Error Correction Specification Change Page Contents 7 ■ Handling of Unused Pin 1. Serial Mode (P/SN pin = “L”) The condition of CDTO pin was added. 2. Parallel Mode (P/SN pin = “H”) The CDTO pin was deleted. 0AH, D5: MCK1E → MCK2E PACKAGE The package dimensions were changed. 56 62 MS0573-E-01 2010/09 - 63 - [AK4115] IMPORTANT NOTICE z These products and their specifications are subject to change without notice. When you consider any use or application of these products, please make inquiries the sales office of Asahi Kasei Microdevices Corporation (AKM) or authorized distributors as to current status of the products. z Descriptions of external circuits, application circuits, software and other related information contained in this document are provided only to illustrate the operation and application examples of the semiconductor products. You are fully responsible for the incorporation of these external circuits, application circuits, software and other related information in the design of your equipments. AKM assumes no responsibility for any losses incurred by you or third parties arising from the use of these information herein. AKM assumes no liability for infringement of any patent, intellectual property, or other rights in the application or use of such information contained herein. z Any export of these products, or devices or systems containing them, may require an export license or other official approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange, or strategic materials. z AKM products are neither intended nor authorized for use as critical componentsNote1) in any safety, life support, or other hazard related device or systemNote2), and AKM assumes no responsibility for such use, except for the use approved with the express written consent by Representative Director of AKM. As used here: Note1) A critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability. Note2) A hazard related device or system is one designed or intended for life support or maintenance of safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property. z It is the responsibility of the buyer or distributor of AKM products, who distributes, disposes of, or otherwise places the product with a third party, to notify such third party in advance of the above content and conditions, and the buyer or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless from any and all claims arising from the use of said product in the absence of such notification. MS0573-E-01 2010/09 - 64 -