Data Sheet

[AK4220]
AK4220
7:3 Audio Switch and 6:3 Video Switch
GENERAL DESCRIPTION
The AK4220 is an AV Switch with 7:3 Audio Switches and 6:3 Video Switches. Using CMOS process to
offer the high performance with low power consumption. In the Audio section, on-chip differential input
circuit could separate the external ground noise. The AK4220 integrates a pop noise free circuit for power
on/pff. The AK4220 is offered in a space saving 64-pin LQFP package, ideal for car navigation
applications.
FEATURES
1. Audio Section
• Selector for 7 inputs and 3 outputs
• Differential Input Circuit for Ground Noise Cannel
• THD+N: -92dB (@1Vrms)
• Dynamic Range: 96dB
• Channel-Independent Output Off
• Pop Noise Free Circuit for Power On/Off
• Channel-Independent Input Detection Circuit
2. Video Section
• Selector for 6 inputs and 3 outputs
• Six Composite Signal Inputs
• Video Driver for Composite Signal Output (+6dB)
• Channel-Independent Hi-Z Output
• On-Chip Sync-tip Clamp Circuit
• Frequency Range: 6MHz
• S/N: 74dB
• Input Detection Circuit
3. Control Section
• Serial µP I/F (I2C, 4-wires serial)
• Five Programmable Output pins
4. Power Supply
• Analog: 4.5V ~ 5.5V
• Digital: 3.0V ~ 3.6V
• Low Power Consumption: 186mW
5. Ta = -40 ∼ 85 °C
6. Package: 64pin LQFP
MS0627-E-01
2010/09
-1-
[AK4220]
AV D D
40kΩ (typ)
AV S S
40kΩ (typ)
LIN + 1
LO U T 1
VCO M
40kΩ (typ)
GND1
MU T E T
40kΩ (typ)
40kΩ (typ)
R IN + 1
40kΩ (typ)
ROUT1
In put #1
LIN + 2
GND2
R IN + 2
MU T E T
O utput #1
(s am e circ uit)
In put #2
LO U T 2
(s am e circ uit)
LIN + 3
GND3
R IN + 3
(s am e circ uit)
LIN + 4
GND4
R IN + 4
(s am e circ uit)
ROUT2
In put #3
O utput #2
In put #4
LO U T 3
(s am e circ uit)
LIN + 5
GND5
R IN + 5
(s am e circ uit)
LIN + 6
GND6
R IN + 6
(s am e circ uit)
LIN + 7
GND7
R IN + 7
(s am e circ uit)
ROUT3
In put #5
O utput #3
In put #6
In put #7
AD ET L
R
O s cillator
VCO M
MU T E T
B ias
ADET R
Figure 1. Audio Block
MS0627-E-01
2010/09
-2-
[AK4220]
VVDD1
VVDD2
VVSS1
Video Drivers
VIN1
VVSS2
VVSS3
VIN2
VIN3
VOUT1
+6dB
VIN4
VIN5
VIN6
VFB1
VOUT2
+6dB
VFB2
VOUT3
+6dB
VFB3
Sync DET
Sync-tip
TEST
PDN
Clamp
DVDD
(A/V control)
DVSS
IICN
SDA/CDTI
SCL/CCLK
INT
(open drain)
Control
Registers
Q0
Q1
Q2
PDN
Q3
CAD1/CSN
Q4
CAD0/CDTO
Figure 2. Video & Control Block
MS0627-E-01
2010/09
-3-
[AK4220]
■ Ordering Guide
−40 ∼ +85°C
64pin LQFP (0.5mm pitch)
Evaluation board for AK4220
AK4220VQ
AKD4220
VIN6 33
AVDD 34
R 35
MUTET 36
VCOM 37
AVSS 38
LOUT1 39
ROUT1 40
LOUT2 41
ROUT2 42
LOUT3 43
ROUT3 44
GND1 45
LIN+1 46
RIN+1 47
GND2 48
■ Pin Layout
49 LIN+2
VIN5 32
50 RIN+2
IICN 31
51 GND3
VIN4 30
52 LIN+3
VVSS1 29
53 RIN+3
VIN3 28
54 GND4
VVDD1 27
56 RIN+4
AK4220
57 GND5
Top View
55 LIN+4
VIN2 26
VVSS3 25
VIN1 24
MS0627-E-01
16 VFB1
15 VOUT1
14 DVSS
13 DVDD
12 Q4
11 Q3
10 Q2
Q1
Q0
8
9
INT
TEST 17
7
64 LIN+7
CAD0
VOUT2 18
6
63 GND7
SDA
VFB2 19
5
62 RIN+6
SCL
VVDD2 20
4
61 LIN+6
CAD1
VOUT3 21
3
60 GND6
PDN
VFB3 22
2
59 RIN+5
RIN+7
VVSS2 23
1
58 LIN+5
2010/09
-4-
[AK4220]
PIN/FUNCTION
No.
1
2
Pin Name
RIN+7
PDN
I/O
I
I
7
8
9
10
11
12
CAD1
CSN
SCL
CCLK
SDA
CDTI
CAD0
CDTO
INT
Q0
Q1
Q2
Q3
Q4
I
I
I
I
I/O
I
I
O
O
O
O
O
O
O
13
DVDD
-
14
15
16
17
18
19
DVSS
VOUT1
VFB1
TEST
VOUT2
VFB2
O
I
I
O
I
20
VVDD2
-
21
22
23
24
25
26
VOUT3
VFB3
VVSS2
VIN1
VVSS3
VIN2
O
I
I
I
27
VVDD1
-
28
29
30
VIN3
VVSS1
VIN4
I
I
31
IICN
I
32
33
VIN5
VIN6
I
I
34
AVDD
-
3
4
5
6
Function
Rch Audio Positive Input 7
Power down Mode
“L”: Power down, Reset
“H”: Power up
The AK4220 should always be reset upon power-up.
Chip Address1 (IICN pin = “L”)
Chip Selector (IICN pin = “H”)
Control Clock Input (IICN pin = “L”)
Control Clock Input (IICN pin = “H”)
Control Data Input/Output (IICN pin = “L”)
Control Data Input (IICN pin = “H”)
Chip Address0 (IICN pin = “L”)
Control Data Output (IICN pin = “H”)
Interrupt
Parallel Output 0 (open drain output)
Parallel Output 1 (open drain output)
Parallel Output 2 (open drain output)
Parallel Output 3 (open drain output)
Parallel Output 4 (open drain output)
Digital Power Supply
Normally connected to DVSS with a 0.1μF ceramic capacitor in parallel
with a 10μF electrolytic capacitor.
Digital Ground
Video Output 1
Video Feedback 1
Test pin, Connected to VVSS.
Video Output 2
Video Feedback 2
Video Power Supply, 5V
Normally connected to VVSS with a 0.1μF ceramic capacitor in parallel
with a 10μF electrolytic capacitor.
Video Output 3
Video Feedback 3
Video Ground2, 0V
Video Input 1
Video Ground3, 0V
Video Input 2
Video Power Supply, 5V
Normally connected to VVSS with a 0.1μF ceramic capacitor in parallel
with a 10μF electrolytic cap.
Video Input 3
Video Ground1, 0V
Video Input 4
Control Mode Selection
“L”(Connected to VVSS): IIC Bus
“H” (Connected to VVDD): 4-wire Serial
Video Input 5
Video Input 6
Audio Power Supply, 5V
Normally connected to AVSS with a 0.1μF ceramic capacitor in parallel
with a 10μF electrolytic capacitor.
MS0627-E-01
2010/09
-5-
[AK4220]
PIN/FUNCTION (Continued)
Current Setting for Oscillator
Normally connected to AVSS with a 12k±1%Ωresistance.
Audio Common Voltage Output2
36
MUTET
O
Normally connected to AVSS with a 1μF ceramic capacitor.
Audio Common Voltage Output1 (Figure 3)
O
Normally connected to AVSS with a 0.1μF ceramic capacitor in parallel
37
VCOM
with a 2.2μF electrolytic capacitor.
38
AVSS
Audio Ground, 0V
39
LOUT1
O
Lch Audio Output 1
40
ROUT1
O
Rch Audio Output 1
41
LOUT2
O
Lch Audio Output 2
42
ROUT2
O
Rch Audio Output 2
43
LOUT3
O
Lch Audio Output 3
44
ROUT3
O
Rch Audio Output 3
45
GND1
I
Audio Input Ground1
46
LIN+1
I
Lch Audio Positive Input 1
47
RIN+1
I
Rch Audio Positive Input 1
48
GND2
I
Audio Input Ground 2
49
LIN+2
I
Lch Audio Positive Input 2
50
RIN+2
I
Rch Audio Positive Input 2
51
GND3
I
Audio Input Ground 3
52
LIN+3
I
Lch Audio Positive Input 3
53
RIN+3
I
Rch Audio Positive Input 3
54
GND4
I
Audio Input Ground 4
55
LIN+4
I
Lch Audio Positive Input 4
56
RIN+4
I
Rch Audio Positive Input 4
57
GND5
I
Audio Input Ground 5
58
LIN+5
I
Lch Audio Positive Input 5
59
RIN+5
I
Rch Audio Positive Input 5
60
GND6
I
Audio Input Ground 6
61
LIN+6
I
Lch Audio Positive Input 6
62
RIN+6
I
Rch Audio Positive Input 6
63
GND7
I
Audio Input Ground 7
64
LIN+7
I
Lch Audio Positive Input 7
Note: All digital input pins (PDN, CAD1-0, SCL and SDA pins) must not be left floating.
35
R
O
AVDD
35kΩ(typ)
VCOM
35kΩ(typ)
2.2uF
0.1uF
AVSS
Figure 3. VCOM Circuit
MS0627-E-01
2010/09
-6-
[AK4220]
■ Handling of Unused Pin
The unused I/O pins should be processed appropriately as below.
Classification
Analog
Digital
Pin Name
LIN+1-LIN+7, RIN+1-RIN+7,
LOUT1-LOUT3,
ROUT1-ROUT3,VIN1-VIN6,
VOU1-VOUT3, VFB1-VFB3,
Q0-Q4, INT
TEST
Setting
These pins should be open.
These pins should be connected to DVSS.
ABSOLUTE MAXIMUM RATINGS
(AVSS = VVSS1-3 = DVSS = 0V; Note: 1)
Parameter
Symbol
min
-0.3
AVDD
Power Supplies
Audio
-0.3
VVDD1
Video
-0.3
VVDD2
Video
-0.3
DVDD
Digital
|AVSS-DVSS|
(Note: 2)
ΔGND1
|AVSS-VVSS1| (Note: 2)
ΔGND2
|AVSS-VVSS2| (Note: 2)
ΔGND3
|AVSS-VVSS3| (Note: 2)
ΔGND4
Input Current (any pins except for supplies)
IIN
Audio Input Voltage
VINA
-0.3
(LIN+1-7, RIN+1-7, GND1-7 pins)
Video Input Voltage1
VINV1
-0.3
(VIN1-6, IICN pins)
Video Input Voltage2
VINV2
-0.3
(VFB1-3, TEST pins)
Digital Input Voltage
VIND
-0.3
(PDN, CAD1-0, SCL ,SDA pins)
Ambient Temperature (power applied)
Ta
-40
Storage Temperature
Tstg
-65
Note: 1. All voltages with respect to ground.
Note: 2. AVSS, VVSS1-3 and DVSS must be connected to the same analog ground plane.
max
6.0
6.0
6.0
6.0
0.3
0.3
0.3
0.3
Units
V
V
V
V
V
V
V
V
±10
AVDD+0.3
mA
V
VVDD1+0.3
V
VVDD2+0.3
V
DVDD+0.3
V
85
150
°C
°C
WARNING: Operation at or beyond these limits may result in permanent damage to the device.
Normal operation is not guaranteed at these extremes.
RECOMMENDED OPERATING CONDITIONS
(AVSS = VVSS1-3 = DVSS = 0V; Note: 1)
Parameter
Symbol
min
typ
Audio
Power Supplies
AVDD
4.5
5.0
Video (Note: 4)
(Note: 3)
VVDD1
4.5
5.0
Video (Note: 4)
VVDD2
4.5
5.0
Digital
DVDD
3.0
3.3
VVDD1 – AVDD
-0.3
0
ΔVDD1
VVDD2 – AVDD
-0.3
0
ΔVDD2
Note: 3. The power-up sequence between AVDD, VVDD1, VVDD2 and DVDD is not critical.
Note: 4. VVDD1 and VVDD2 must be the same voltage.
max
5.5
5.5
5.5
3.6
+0.3
+0.3
Units
V
V
V
V
V
V
*AKM assumes no responsibility for the usage beyond the conditions in this datasheet.
MS0627-E-01
2010/09
-7-
[AK4220]
ANALOG CHARACTERISTICS (AUDIO)
(Ta=25°C; AVDD = VVDD1-2 = 5V, DVDD =3.3V; AVSS = VVSS1-3 = DVSS = 0V; Signal Frequency=1kHz,
Measurement Frequency=20Hz∼20kHz, unless otherwise specified)
Parameter
min
typ
max
Units
S/(N+D)
Input=0dBV
82
92
dB
DR (0dBV)
Input=-60dBV, A-weighted
88
96
dB
S/N (0dBV)
Input=0ff, A-weighted
88
96
dB
Input Impedance
(Note: 5)
20
kΩ
Maximum Input Voltage
(Note: 6)
1
Vrms
Gain
-0.5
0
0.5
dB
Interchannel Isolation
(Note: 7)
100
dB
Interchannel Gain Mismatch
0.2
dB
Gain Drift
20
ppm/°C
Load Resistance
(Note: 8) R1+R2 (Figure 4)
5
kΩ
400
pF
Load Capacitance
C1
(Figure 4)
30
pF
C2
(Figure 4)
Power Supply Rejection
(Note: 9)
50
dB
Input Detection Circuit
Input Reception
1kHz (Note: 10)
-43
-31
-26
dBV
Input Reception Adjustment Gain Step (Note: 11)
3
dB
Note: 5. Connected GND1-7 to GND using a capacitor for AC-coupling.
Note: 6. The Input Voltage meets S/(N+D)>82dB
Note: 7. Between all channels of LIN1-7 and RIN1-7.
Note: 8. The output resistance of audio output (LOUT1-3 and ROUT1-3) are less than l0Ω(typ).
Note: 9. Applied to AVDD, VVDD1-2 and DVDD with a sine wave (1kHz, 50mVpp).
Note: 10. Detect an instant value. 31dBV=+40mV0p. If the input voltage is smaller than the detection reception value, the
signal isn’t detected, and if the input voltage is larger than the detection reception value, the signal is detected.
The input reception value is proportional to AVDD voltage as of 0.008 x AVDD V0p(typ).
Note: 11. Input Reception Adjustment Gain is +6dB∼-6dB.
R1
300Ω
C3
10uF
LOUT1-3
ROUT1-3
R2
4.7kΩ
C21
C22
C2=C21+C22= 30pF(max)
C1
C1= 400pF(max)
Figure 4. Load Resistance R1, R2 and Load Capacitance C1, C2.
MS0627-E-01
2010/09
-8-
[AK4220]
ANALOG CHARACTERISTICS (VIDEO)
(Ta=25°C; AVDD = VVDD1-2 = 5V, DVDD =3.3V; AVSS = VVSS1-3 = DVSS = 0V; unless otherwise specified)
Parameter
Conditions
min
typ
max
Units
At output pin.
0.6
V
Sync Tip Clamp Voltage
(Note: 12)
Gain (Note: 13)
Input=0.3Vp-p, 100kHz
5.5
6
6.5
dB
Frequency Response (Note: 13) Input=0.3Vp-p, 100kHz to 6MHz.
-1.0
1.0
dB
Maximum Input Signal
f=100kHz, maximum with distortion < 1.0%,
1.5
Vpp
gain=6dB(typ).
Load Resistance
R1+R2(Note: 14)
150
Ω
400
pF
Load Capacitance
C1 (Note: 14)
15
pF
C2 (Note: 14)
Interchannel Isolation (Note: 15) f=4.43MHz, 1Vpp input.
50
dB
S/N
Reference Level = 0.7Vpp, CCIR 567
74
dB
weighting. BW= 15kHz to 5MHz.
Differential Gain
0.7Vpp 5steps modulated staircase.
%
±0.4
chrominance &burst are 280mVpp, 4.43MHz.
Differential Phase
0.7Vpp 5steps modulated staircase.
Degree
±0.9
chrominance &burst are 280mVpp, 4.43MHz.
Input Detection Circuit
Input Reception (Note: 16)
0.04
0.07
0.1
Vpp
Note: 12. SAGN bit=“1”, DC output. There is no specification for using the Sag Compensation circuit (SAGN bit=“0”).
Sync Tip Clamp Voltage is proportional to AVDD voltage, VOUT=0.17 x AVDD V(typ).
Note: 13. If SAGN bit=“0” for using the Sag Compensation circuit, the measurement point is between C3 and R1 of
Figure 5. If SAGN bit=“1” for DC output, the measurement point is video output pin.
Note: 14. See Figure 5 and Figure 6.
Note: 15. Between all channels of VIN1-6.
Note: 16. If the input voltage is smaller than the detection reception value, the signal isn’t detected. If the input voltage is
larger than the detection reception value, the signal is detected. The input reception value is proportional to
AVDD voltage, 0.014 x AVDD Vpp(typ).
R1
75Ω
C3
100uF
+6dB
VOUT
C4
2.2uF
R2
75Ω
VFB
C21
C22
C23
C1
C2=C21+C22+C23= 15pF(max)
C1= 400pF(max)
Figure 5. Load Resistance R1, R2 and Load Capacitance C1, C2 (SAGN bit=“0”, using the Sag Compensation circuit)
R1
75Ω
+6dB
VOUT
R2
75Ω
VFB
C2
C2=15pF(max)
C1
C1=400pF(max)
Figure 6. Load Resistance R1, R2 and Load Capacitance C1, C2 (SAGN bit=“1”, DC output)
MS0627-E-01
2010/09
-9-
[AK4220]
DC CHARACTERISTICS
(Ta=-40∼85°C; AVDD = VVDD1-2 = 4.5∼5.5V, DVDD =3.0∼3.6V)
Parameter
Symbol
min
70%DVDD
VIH
High-Level Input Voltage
(PDN, SCL,SDA,CAD0-1,TEST,IICN pins)
VIL
Low-Level Input Voltage
(PDN, SCL,SDA,CAD0-1,TEST,IICN pins)
DVDD-0.4
VOH
High-Level Output Voltage (Iout=-400μA)
Low-Level Output Voltage
VOL
(CDTO pin: Iout=400μA)
VOL
(Q0-4, INT pins: Iout=1mA)
VOL
(SDA pin: Iout=3mA)
Input Leakage Current
Iin
Parameter
Power Supplies
Power Supply Current
Normal Operation (PDN pin = “H”)
AVDD
VVDD1+VVDD2
DVDD
Power-down mode (PDN pin = “L”)
AVDD
VVDD1+VVDD2
DVDD
Total
min
typ
-
max
-
Units
V
-
30%DVDD
V
-
-
V
-
0.4
0.4
0.4
±10
V
V
V
μA
typ
max
Units
18
18
1
27
27
2
mA
mA
mA
50
μA
μA
μA
μA
(Note: 17)
(Note: 18)
(Note: 19)
10
10
10
30
Note: 17. No input and no load.
Note: 18. If the output is DC output (SAGN bit =“1”), the current corresponded to the load resistance is added to no load
current (typ. 18mA).
Note: 19. All analog input pins are no input, and all digital input pins are fixed to DVSS.
MS0627-E-01
2010/09
- 10 -
[AK4220]
SWITCHING CHARACTERISTICS
(Ta= -40∼85°C; AVDD = VVDD1-2 = 4.5∼5.5V, DVDD= 3.0∼3.6V, CL= 20pF)
Control Interface Timing (I2C Bus, Note: 20)
SCL Clock Frequency
fSCL
Bus Free Time Between Transmissions
tBUF
1.3
Start Condition Hold Time (prior to first clock pulse)
tHD:STA
0.6
Clock Low Time
tLOW
1.3
Clock High Time
tHIGH
0.6
Setup Time for Repeated Start Condition
tSU:STA
0.6
SDA Hold Time from SCL Falling
(Note: 21)
tHD:DAT
0
SDA Setup Time from SCL Rising
tSU:DAT
0.1
Rise Time of Both SDA and SCL Lines
tR
Fall Time of Both SDA and SCL Lines
tF
Setup Time for Stop Condition
tSU:STO
0.6
Pulse Width of Spike Noise Suppressed by Input Filter
tSP
0
Capacitive load on bus
Cb
Control Interface Timing (4-wire serial mode)
tCCK
200
CCLK Period
tCCKL
80
CCLK Pulse Width Low
tCCKH
80
Pulse Width High
tCDS
50
CDTI Setup Time
tCDH
50
CDTI Hold Time
tCSW
150
CSN “H” Time
tCSS
50
CSN “↓” to CCLK “↑”
tCSH
50
CCLK “↑” to CSN “↑”
tDCD
CDTO Delay
tCCZ
CSN “↑” to CDTO Hi-Z
Power-down & Reset Timing
TPD
150
PDN Pulse Width
(Note: 21)
2
Note: 20. I C-bus is a trademark of NXP B.V.
Note: 21. Data must be held for sufficient time to bridge the 300 ns transition time of SCL.
Note: 22. The AK4220 should be reset by PDN pin = “L” upon power up.
MS0627-E-01
400
0.3
0.3
50
400
kHz
μs
μs
μs
μs
μs
μs
μs
μs
μs
μs
ns
pF
45
70
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
2010/09
- 11 -
[AK4220]
■ Timing Diagram
VIH
SDA
VIL
tLOW
tBUF
tR
tHIGH
tF
tSP
VIH
SCL
VIL
tHD:STA
Stop
tHD:DAT
tSU:DAT
tSU:STA
tSU:STO
Start
Stop
Start
Figure 7. I2C Bus Mode Timing
VIH
CSN
VIL
tCSS
tCCK
tCCKL tCCKH
VIH
CCLK
VIL
tCDH
tCDS
C1
CDTI
C0
A4
R/W
VIH
VIL
Hi-Z
CDTO
Figure 8. WRITE/READ Command Input Timing (4-wire serial mode)
tCSW
VIH
CSN
VIL
tCSH
VIH
CCLK
CDTI
CDTO
VIL
D3
D2
D1
D0
VIH
VIL
Hi-Z
Figure 9. WRITE Data Input Timing (4-wire serial mode)
MS0627-E-01
2010/09
- 12 -
[AK4220]
VIH
CSN
VIL
VIH
CCLK
CDTI
VIL
A1
VIH
A0
VIL
tDCD
Hi-Z
CDTO
D7
D6
D5
50%DVDD
Figure 10. READ Data Output Timing1 (4-wire serial mode)
tCSW
VIH
CSN
VIL
tCSH
VIH
CCLK
VIL
VIH
CDTI
VIL
tCCZ
CDTO 50%DVDD
Hi-Z
D2
D1
D0
Figure 11. READ Data Output Timing2 (4-wire serial mode)
tPD
PDN
VIL
Figure 12. Power-down & Reset Timing
MS0627-E-01
2010/09
- 13 -
[AK4220]
OPERATION OVERVIEW
■ Power-down options
The AK4220 should be reset once by bringing PDN pin = “L” upon power-up.
■ Audio Bias Control Circuit
The AK4220 has an on-chip audio bias voltage control circuit. Bringing BIAS bit to “1”, the bias voltage (MUTET pin)
smoothly set from AVSS to AVDD/2(typ) by 150ms (typ, Note: 23). The change of BIAS bit from “1” to “0” also makes
smooth transient from AVDD/2(typ) to AVSS by 150ms (typ, Note: 23). This feature achieves pop noise free at
power-on/off.
Note: 23. AVDD=5.0V, the capacitor of MUTET pin is C=1uF. The rise and fall times are proportional to the voltage of
AVDD and the capacitor value of MUTET pin.
PDN pin
BIAS bit
“0” (default)
“1”
“0”
150ms (typ)
150ms (typ)
Audio bias level
Figure 13. BIAS bit
■ Audio Signal Input, Video Signal Input
1. Audio Signal Input
The ground noise can be cancelled by the differential input with the same ground for L and R channel. The output of LIN
and RIN are the same phase. LIN+1-7, RIN+1-7 and GND1-7 pins must be AC coupled using 0.47uF capacitor.
2. Video Signal Input
Tip Sync level is fixed by internal clamp circuit. VIN1-6 pins must be input through 0.47uF capacitor for AC coupling.
MS0627-E-01
2010/09
- 14 -
[AK4220]
■ Input Selector
The AK4220 have 7:3 input selectors for audio input, and 6:3 input selectors for video input. The audio input selectors are
set by ASEL12-10bits, ASEL22-20bits and ASEL32-30 bits, and the video input selectors are set by VSEL12-10bits,
VSEL22-20bits and VSEL32-30 bits.
ASEL12 bit
0
0
0
0
1
1
1
1
ASEL11 bit
0
0
1
1
0
0
1
1
ASEL10 bit
0
1
0
1
0
1
0
1
Input Selector
Off (Note: 24)
LIN1 / RIN1
LIN2 / RIN2
LIN3 / RIN3
LIN4 / RIN4
LIN5 / RIN5
LIN6 / RIN6
LIN7 / RIN7
(default)
Table 1. Audio Input Selector 1 (LOUT1/ROUT1)
ASEL22 bit
0
0
0
0
1
1
1
1
ASEL21 bit
0
0
1
1
0
0
1
1
ASEL20 bit
0
1
0
1
0
1
0
1
Input Selector
Off (Note: 24)
LIN1 / RIN1
LIN2 / RIN2
LIN3 / RIN3
LIN4 / RIN4
LIN5 / RIN5
LIN6 / RIN6
LIN7 / RIN7
(default)
Table 2. Audio Input Selector 2 (LOUT2/ROUT2)
ASEL32 bit
0
0
0
0
1
1
1
1
ASEL31 bit
0
0
1
1
0
0
1
1
ASEL30 bit
0
1
0
1
0
1
0
1
Input Selector
Off (Note: 24)
LIN1 / RIN1
LIN2 / RIN2
LIN3 / RIN3
LIN4 / RIN4
LIN5 / RIN5
LIN6 / RIN6
LIN7 / RIN7
(default)
Table 3. Audio Input Selector 3 (LOUT3/ROUT3)
Note: 24. The audio outputs become common voltage (VCOM) when the input selectors are off. If BIAS bit = “0”, the
outputs become 0V.
MS0627-E-01
2010/09
- 15 -
[AK4220]
VSEL12 bit
0
0
0
0
1
1
1
1
VSEL11 bit
0
0
1
1
0
0
1
1
VSEL10 bit
0
1
0
1
0
1
0
1
Input Selector
Off (Note: 25)
VIN1
VIN2
VIN3
VIN4
VIN5
VIN6
N/A
(default)
Table 4. Video Input Selector 1 (VOUT1)
VSEL22 bit
0
0
0
0
1
1
1
1
VSEL21 bit
0
0
1
1
0
0
1
1
VSEL20 bit
0
1
0
1
0
1
0
1
Input Selector
Off (Note: 25)
VIN1
VIN2
VIN3
VIN4
VIN5
VIN6
N/A
(default)
Table 5. Video Input Selector 2 (VOUT2)
VSEL32 bit
0
0
0
0
1
1
1
1
VSEL31 bit
0
0
1
1
0
0
1
1
VSEL30 bit
0
1
0
1
0
1
0
1
Input Selector
Off (Note: 25)
VIN1
VIN2
VIN3
VIN4
VIN5
VIN6
N/A
(default)
Table 6. Video Input Selector 3 (VOUT3)
Note: 25. The video outputs become Hi-Z when the input selectors are off.
MS0627-E-01
2010/09
- 16 -
[AK4220]
■ Input Detection Circuit, INT pin Output
The AK4220 has channel-independent audio input detection circuit and video synchronization signal detection circuit.
Each input source is set as shown in Table 7 and Table 8.
ADSEL2 bit
0
0
0
0
1
1
1
1
ADSEL1 bit
0
0
1
1
0
0
1
1
ADSEL0 bit
0
1
0
1
0
1
0
1
Detection Source
Off
LIN1 / RIN1
LIN2 / RIN2
LIN3 / RIN3
LIN4 / RIN4
LIN5 / RIN5
LIN6 / RIN6
LIN7 / RIN7
(default)
Table 7. Audio Input Detection Selector
VDSEL2 bit
0
0
0
0
1
1
1
1
VDSEL1 bit
0
0
1
1
0
0
1
1
VDSEL0 bit
0
1
0
1
0
1
0
1
Detection Source
Off
VIN1
VIN2
VIN3
VIN4
VIN5
VIN6
N/A
(default)
Table 8. Video Synchronization Signal Detection Selector
1. ADETL bit (Lch Audio Input Detection), ADETR bit (Rch Audio Input Detection)
The audio input detection circuit samples the input signal by accuracy of 100kHz±30%.
If the signal over the detection reception value is detected consecutively more than the frequency set by ACT1-0 bits,
ADETL-R bits become “1” and if the signal over the detection reception value isn’t detected consecutively more than the
frequency set by ACT1-0 bits during the time set by RTM1-0 bit, ADETL-R bits become “0”.
The audio input detection for L/R channels is done independently. The input reception can be adjusted in the range of
±6dB from -31dBV(= +40mV0p)(typ) by LV2-0 bits. When writing to 05H(ADSEL2-0, ACT1-0, RTMI1-0 bits), the
counters for the consecutive detection frequency and recovery time are reset, and ADETL/R bits are reset to “0”.
The setting of MADEL/R bit doesn’t affect the operation of ADETL/R bit.
MS0627-E-01
2010/09
- 17 -
[AK4220]
LV2 bit
0
0
0
0
1
1
1
1
LV1 bit
0
0
1
1
0
0
1
1
Input Reception
-6dB
-3dB
0dB
(default)
+3dB
+6dB
N/A
N/A
N/A
0dB = +40mV0p(typ)
Table 9. Level Setting of Audio Input Detection
ACT1 bit
0
0
1
1
LV0 bit
0
1
0
1
0
1
0
1
ACT0 bit
0
1
0
1
Consecutive Detect Frequency
1
2
4
8
(default)
Table 10. Consecutive Detection frequency Setting of Audio Input Detection
RTM1 bit
RTM0 bit
0
0
1
1
0
1
0
1
Recovery Time
(typ)
40ms
80ms
160ms
320ms
(default)
Table 11. Recovery Time Setting of Audio Input Detection
Detect Level
-31dBV(default)
Input pin
(ex. LIN+1)
Input signal level exceeds the detection reception value during
sampling x consecutive detect frequency.
Input signal level doesn’t exceeds the detection reception value
during sampling x consecutive detect frequency.
Recovery Time
ADETL bit
INT pin
“0”
Hi-Z (pulled-up)
“1”
“L”
“0”
Hi-Z (pulled-up)
Figure 14. Audio Detection Operation
MS0627-E-01
2010/09
- 18 -
[AK4220]
2. VDET bit (Video Sync Signal Detection)
The video sync signal detection circuit can change the detection mode by VDMD bit.
VDMD bit =“0” (default)
When video sync signal above 0.07Vpp(typ) is detected, VDET bit become “1” and VDET bit returns to “0” after reading
the register of 08H. The VDET bit is also reset to “0” by writing to the register of 04H with VDSEL2-0 bits.
VDMD bit =“1”
The detection circuit counts the number of video sync signal above 0.07Vpp(typ) every 40ms(±30%) period generated by
the internal counter. When the period with the sync of 384 or more continues tow times, the VDET bit becomes “1” after
1/2 period. When the period with the sync signal less than 384 continues tow times, the VDET bit becomes “0” after 1/2
period.
The internal timer isn’t reset when changing the input source. Therefore the detection time, from after changing the input
source to VDET bit = “1”, depends on the timing of input source change.
In case of a period that the internal timer count is the shortest(40ms x 70% = 28ms), when the detection circuit counts 384
times during the first period that receives video sync signal and counts 384 times or more in the following period, the
detection time becomes the shortest.
Detection time (min) = (1/fH) x 384 + 28ms x 1.5 ≅ 66.6ms @ fH=15.625kHz
fH: frequency of video synchronization signal
If a period that internal timer counts is the longest (40ms x 130% = 52ms), when the detection circuit counts only 383
times during the first period that receives video sync signal and counts 384 times or more in the following two periods, the
detection time becomes the longest.
Detection time (max) = (1/fH) x 384 + 52ms x 2.5 ≅ 154.5ms @ fH=15.625kHz
fH: frequency of video synchronization signal
When writing to 04H(VDSEL2-0bits), the internal timer is reset and VDET bit becomes “0”.
The setting of MVDET bit doesn’t affect the operation of VDET bit.
1st period
2nd period
3rd period
4th period
Input pin
(ex. VIN1)
≥384 times
VDET bit
≥384 times
“0”
“1”
Input pin
(ex. VIN1)
≤384 times
VDET bit
≥384 times
≥384 times
“0”
“1”
Figure 15. VDET bit timing (VDMD bit =“1”)
MS0627-E-01
2010/09
- 19 -
[AK4220]
3. INT pin output
The output source of INT pin is ORed between ADETL/R bits and VDET bit If the output source of INT pin is “H”, INT
pin=“L”, and if the output source of INT pin is “L”, INT pin=“Hi-Z”. If each mask bit is “1”, each detection bit is masked
independently and the detection result isn’t reflected to INT pin.
+3.3V
DVDD
AK4220
10k
VDET
MVDET
INT pin
ADETL
MADETL
ADETR
MADETR
DVSS
Figure 16. INT Pin Output
MVDET bit
0
0
0
0
1
1
1
1
MADETL bit
0
0
1
1
0
0
1
1
MADETR bit
0
1
0
1
0
1
0
1
INT pin output source
“OR” (VDET bit, ADETL bit, ADETR bit)
“OR” (VDET bit , ADETL bit)
“OR” (VDET bit, ADETR bit)
VDET bit
“OR” (ADETL bit, ADETR bit)
ADETL bit
ADETR bit
“L”(INT pin = “Hi-Z”)
(default)
Table 12. INT Pin Output Setting
MS0627-E-01
2010/09
- 20 -
[AK4220]
■ Parallel Output Circuit, INT Output Circuit, SDA Output Circuit
Q0-4 bits setting are output from Q0-4 pins. Each output is open drain. Normally connected to DVSS with a 10kohm
resistance. INT pin is the same output circuit (Refer Figure 16).
SDA pin is open drain output, and connected to DVSS with a resistance. Refer to I2C bus standard as for resistance value.
As there is a protection between each pin and DVDD, the pulled-up voltage should be DVDD or lower. And if the
pulled-up voltage is supplied from the different power supply from DVDD, only DVDD should not be powered off
independently. When PDN pin =“L” and DVDD is supplied to the AK4220, the AK4220 can be in power-down state. In
Power-down state, VVDD1-2 and AVDD can be powered off.
+3.3V
DVDD
10k
AK4220
Q0-4 pin
Q0~Q4 bit
DVSS
Figure 17. Q0-Q4 Pin Output
+3.3V
DVDD
AK4220
SDA pin
DVSS
Figure 18. SDA Pin Output
MS0627-E-01
2010/09
- 21 -
[AK4220]
■ Serial Control Interface
1. 4 wire serial control mode (IICN pin = “H”)
With the 4-wire μP interface pins (CSN, CCLK, CDTI and CDTO), the data on this interface consists of the Chip address
(2-bits, Fixed to “00”), Read/Write (1-bit), Register address (MSB first, 5-bits) and Control data (MSB first, 8-bits). The
data are clocked in on the rising edge of CCLK, and data are clocked out on the falling edge of CCLK. For write
operations, the data is latched after a low-to-high transition of the 16th CCLK. For read operation, the data is outputted to
Hi-Z on the rising edge of CSN. The clock speed of CCLK is 5MHz(max). The value of the internal registers is initialized
at PDN pin = “L”.
CSN
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
CCLK
WRITE
CDTI
C1 C0 R/W A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0
Hi-Z
CDTO
READ
CDTI
C1 C0 R/W A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0
Hi-Z
CDTO
C1,C0:
R/W:
A4-A0:
D7-D0:
D7 D6 D5 D4 D3 D2 D1 D0
Hi-Z
Chip Address: ( Fixed to “00”)
READ/WRITE (0:READ, 1:WRITE)
Register Address
Control Data
Figure 19. 4-wrie Serial Control I/F Timing
MS0627-E-01
2010/09
- 22 -
[AK4220]
2. I2C bus control mode (IICN pin = “L”)
The AK4220 supports the fast-mode I2C-bus system (max: 400kHz).
1. WRITE Operations
Figure 20 shows the data transfer sequence for the I2C-bus mode. All commands are preceded by a START condition. A
HIGH to LOW transition on the SDA line while SCL is HIGH indicates a START condition (Figure 26). After the
START condition, a slave address is sent. This address is 7 bits long followed by the eighth bit that is a data direction bit
(R/W). The most significant five bits of the slave address are fixed as “00100”. The next one bit is CAD0 (device address
bit). This bit identifies the specific device on the bus. The hard-wired input pin (CAD0 pin) set these device address bits
(Figure 21). If the slave address matches that of the AK4220, the AK4220 generates an acknowledge and the operation is
executed. The master must generate the acknowledge-related clock pulse and release the SDA line (HIGH) during the
acknowledge clock pulse (Figure 27). A R/W bit value of “1” indicates that the read operation is to be executed. A “0”
indicates that the write operation is to be executed.
The second byte consists of the control register address of the AK4220. The format is MSB first, and those most
significant 4-bits are fixed to zeros (Figure 22). The data after the second byte contains control data. The format is MSB
first, 8bits (Figure 23). The AK4220 generates an acknowledge after each byte has been received. A data transfer is
always terminated by a STOP condition generated by the master. A LOW to HIGH transition on the SDA line while SCL
is HIGH defines a STOP condition (Figure 26).
The AK4220 can perform more than one byte write operation per sequence. After receipt of the third byte the AK4220
generates an acknowledge and awaits the next data. The master can transmit more than one byte instead of terminating the
write cycle after the first data byte is transferred. After receiving each data packet the internal 5-bit address counter is
incremented by one, and the next data is automatically taken into the next address. If the address exceeds 08H prior to
generating the stop condition, the address counter will “roll over” to 00H and the previous data will be overwritten.
The data on the SDA line must remain stable during the HIGH period of the clock. The HIGH or LOW state of the data
line can only change when the clock signal on the SCL line is LOW (Figure 28) except for the START and STOP
conditions.
S
T
A
R
T
SDA
S
T
O
P
R/W="0"
Slave
S Address
Sub
Address(n)
Data(n)
A
C
K
Data(n+1)
A
C
K
A
C
K
Data(n+x)
A
C
K
P
A
C
K
A
C
K
Figure 20. Data Transfer Sequence at the I2C-Bus Mode
0
0
1
0
0
CAD1
CAD0
R/W
A2
A1
A0
D2
D1
D0
Figure 21. The First Byte
0
0
0
0
A3
Figure 22. The Second Byte
D7
D6
D5
D4
D3
Figure 23. Byte Structure after the second byte
MS0627-E-01
2010/09
- 23 -
[AK4220]
2. READ Operations
Set the R/W bit = “1” for the READ operation of the AK4220. After transmission of data, the master can read the next
address’s data by generating an acknowledge instead of terminating the write cycle after the receipt of the first data word.
After receiving each data packet the internal 5-bit address counter is incremented by one, and the next data is
automatically taken into the next address. If the address exceeds 09H prior to generating a stop condition, the address
counter will “roll over” to 00H and the previous data will be overwritten.
The AK4220 supports two basic read operations: CURRENT ADDRESS READ and RANDOM ADDRESS READ.
2-1. CURRENT ADDRESS READ
The AK4220 contains an internal address counter that maintains the address of the last word accessed, incremented by
one. Therefore, if the last access (either a read or write) were to address n, the next CURRENT READ operation would
access data from the address n+1. After receipt of the slave address with R/W bit set to “1”, the AK4220 generates an
acknowledge, transmits 1-byte of data to the address set by the internal address counter and increments the internal
address counter by 1. If the master does not generate an acknowledge to the data but instead generates a stop condition,
the AK4220 ceases transmission.
S
T
A
R
T
SDA
S
T
O
P
R/W="1"
Slave
S Address
Data(n+1)
A
C
K
Data(n+2)
Data(n+3)
A
C
K
A
C
K
Data(n+1+x)
A
C
K
A
C
K
P
A
C
K
Figure 24. CURRENT ADDRESS READ
2-2. RANDOM ADDRESS READ
The random read operation allows the master to access any memory location at random. Prior to issuing the slave address
with the R/W bit set to “1”, the master must first perform a “dummy” write operation. The master issues a start request, a
slave address (R/W bit = “0”) and then the register address to read. After the register address is acknowledged, the master
immediately reissues the start request and the slave address with the R/W bit set to “1”. The AK4220 then generates an
acknowledge, 1 byte of data and increments the internal address counter by 1. If the master does not generate an
acknowledge to the data but instead generates a stop condition, the AK4220 ceases transmission.
S
T
A
R
T
SDA
S
T
A
R
T
R/W="0"
Slave
S Address
Slave
S Address
Sub
Address(n)
A
C
K
A
C
K
S
T
O
P
R/W="1"
Data(n)
A
C
K
Data(n+1)
A
C
K
Data(n+x)
A
C
K
A
C
K
P
A
C
K
Figure 25. RANDOM ADDRESS READ
MS0627-E-01
2010/09
- 24 -
[AK4220]
SDA
SCL
S
P
start condition
stop condition
Figure 26. START and STOP Conditions
DATA
OUTPUT BY
TRANSMITTER
not acknowledge
DATA
OUTPUT BY
RECEIVER
acknowledge
SCL FROM
MASTER
2
1
8
9
S
clock pulse for
acknowledgement
START
CONDITION
Figure 27. Acknowledge on the I2C-Bus
SDA
SCL
data line
stable;
data valid
change
of data
allowed
Figure 28. Bit Transfer on the I2C-Bus
MS0627-E-01
2010/09
- 25 -
[AK4220]
■ Register Map
Addr
00H
01H
02H
03H
04H
05H
06H
07H
08H
Register Name
Power Down & Reset
Input Selector 1
Input Selector 2
Input Selector 3
Detection Control1
Detection Control2
Detection Control3
Parallel Output
AV Detection
D7
0
0
0
0
0
RTM1
VDMD
0
0
D6
0
VSEL12
VSEL22
VSEL32
VDSEL2
RTM0
MVDET
0
VDET
D5
0
VSEL11
VSEL21
VSEL31
VDSEL1
ACT1
D4
SAGN
VSEL10
VSEL20
VSEL30
VDSEL0
ACT0
MADETR
MADETL
0
ADETR
Q4
ADETL
D3
0
0
0
0
0
0
0
Q3
0
D2
0
ASEL12
ASEL22
ASEL32
0
ADSEL2
LV2
Q2
0
D1
BIAS
ASEL11
ASEL21
ASEL31
0
ADSEL1
LV1
Q1
0
D0
PW
ASEL10
ASEL20
ASEL30
0
ADSEL0
LV0
Q0
0
Note:
When the PDN pin goes “L”, the registers are initialized to their default values.
The bits indicated to “0” in the register map must contain a “0” value.
Do not write any data to the register over 09H.
■ Register Definitions
Reset & Initialize
Addr
00H
Register Name
Power Down & Reset
R/W
Default
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
SAGN
0
0
BIAS
PW
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
1
PW: Power bit
0: Power-down except register control block. The register don’t change. (default)
1: Normal operation
When PDN pin=“L”, PW bit becomes “1” and the registers are initialized to their default values.
BIAS: Audio Bias Power bit
0: Power-down the Audio Bias Circuit (default)
1: Normal operation
SAGN: Video output selector bit
0: Sag Compensation mode (default)
1: DC output mode
Addr
01H
Register Name
Input Selector 1
R/W
Default
D7
D6
D5
D4
D3
D2
D1
D0
0
VSEL12
VSEL11
R/W
0
R/W
0
R/W
0
VSEL10
0
ASEL12
ASEL11
ASEL10
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
ASEL12-10: Audio Input Selector 1
Refer Table 1
VSEL12-10: Video Input Selector 1
Refer Table 4
MS0627-E-01
2010/09
- 26 -
[AK4220]
Addr
Register Name
Input Selector 2
R/W
Default
02H
D7
D6
D5
D4
D3
D2
D1
D0
0
VSEL22
VSEL21
R/W
0
R/W
0
R/W
0
VSEL20
0
ASEL22
ASEL21
ASEL20
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
ASEL22-20: Audio Input Selector 2
Refer Table 2
VSEL22-20: Video Input Selector 2
Refer Table 5
Addr
Register Name
Input Selector 3
R/W
Default
03H
D7
D6
D5
D4
D3
D2
D1
D0
0
VSEL32
VSEL31
VSEL30
0
ASEL32
ASEL31
ASEL30
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
D6
D5
D4
D3
D2
D1
D0
0
0
0
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
D2
D1
D0
ASEL32-30: Audio Input Selector 3
Refer Table 3
VSEL32-30: Video Input Selector 3
Refer Table 6
Addr
04H
Register Name
Detection Control1
R/W
Default
D7
0
R/W
0
VDSEL2 VDSEL1 VDSEL0
R/W
0
R/W
0
VDSEL2-0: Video Synchronization Signal Detection Selector
Refer Table 8
Addr
05H
Register Name
Detection Control2
R/W
Default
D7
D6
D5
D4
D3
RTM1
RTM0
ACT1
ACT0
0
R/W
0
R/W
1
R/W
0
R/W
0
R/W
0
ADSEL2 ADSEL1 ADSEL0
R/W
0
R/W
0
R/W
0
ADSEL2-0: Audio Input Detection Selector
Refer Table 7
ACT1-0: Audio Input Continuous Detection times Setting
Refer Table 10
RTM1-0: Audio Input Detection Recovery time Setting
Refer Table 11
MS0627-E-01
2010/09
- 27 -
[AK4220]
Addr
06H
Register Name
Detection Control3
R/W
Default
D7
VDMD
D6
D5
D4
MVDET MADETR MADETL
R/W
0
R/W
0
R/W
0
R/W
0
D3
D2
D1
D0
0
LV2
LV1
LV0
R/W
0
R/W
0
R/W
1
R/W
0
LV2-0: Audio Input Detection Level Setting
Refer Table 9
MADETL/R: Audio Input Detection Mask Setting for Lch/Rch
Refer Table 12
MVDET: Video Synchronization Signal Detection Mask Setting
Refer Table 12
VDMD: Video Synchronization Signal Detection Mode Setting
“0”: If video signal above 0.07Vpp(typ) is detected VDET bit becomes “1” and when reading 08H
VDET bit becomes “0”. (default)
“1”: Refer VDET bit (Video Synchronization Signal Detection) section (Page19).
Addr
Register Name
Parallel Output
R/W
Default
07H
D7
D6
D5
D4
D3
D2
D1
0
0
0
Q4
Q3
Q2
Q1
D0
Q0
R/W
0
R/W
0
R/W
0
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
D0
Q4-0: Parallel Output Setting
“1”: Hi-Z(default)
“0”: “L” Output
Addr
Register Name
AV Detection
R/W
Default
08H
D7
D6
D5
D4
D3
D2
D1
0
VDET
ADETR
ADETL
0
0
0
0
READ
0
READ
0
READ
0
READ
0
READ
0
READ
0
READ
0
READ
0
ADETL/R: Audio Input Detection States for Lch/Rch
“0”: Undetected (default)
“1”: Detected
VDET: Video Synchronization Signal Detection States
“0”: Undetected (default)
“1”: Detected
Writing to address 08H will be ignored.
MS0627-E-01
2010/09
- 28 -
[AK4220]
SYSTEM DESIGN
Figure 29 shows the system connection diagram. An evaluation board [AKD4220] is available which demonstrates the
optimum layout, power supply arrangements and measurement results.
Analog Ground
Audio in
0.47u
0.47u
LIN+2 49
RIN+2 50
0.47u
0.47u
0.47u
GND3 51
LIN+3 52
RIN+3 53
GND4 54
0.47u
0.47u
LIN+4 55
0.47u
0.47u
0.47u
0.47u
0.47u
0.47u
0.47u
0.47u
RIN+4 56
GND5 57
LIN+5 58
RIN+5 59
GND6 60
LIN+6 61
RIN+6 62
LIN+7 64
GND2 48
2 PDN
RIN+1 47
0.47u
3 CAD1
LIN+1 46
0.47u
4 SCL
GND1 45
5 SDA
ROUT3 44
6 CAD0
LOUT3 43
7 INT
ROUT2 42
8 Q0
ROUT1 40
10 Q2
10u
AVSS 38
12 Q4
VCOM 37
0.1u
+
13 DVDD
MUTET 36
14 DVSS
R 35
300
10u
300
10u
300
10u
300
+
Analog 5V
32 VIN5
31 IICN
30 VIN4
29 VVSS1
28 VIN3
27 VVDD1
0.1u 10u
1u
0.1u
75
+
75
0.1u
0.1u
75
0.1u
75
2.2u
VIN6 33
Audio out
75
100u
+
0.1u
10u 0.1u
26 VIN2
25 VVSS3
24 VIN1
23 VVSS2
22 VFB3
21 VOUT3
20 VVDD2
10u 0.1u
19 VFB2
2.2u
100u
75
2.2u
300
10u
+
0.1u 2.2u
AVDD 34
18 VOUT2
17 TEST
16 VFB1
100u
300
10u
12k
15 VOUT1
75
10u
75
0.1u
10k
LOUT1 39
11 Q3
Audio in
0.47u
LOUT2 41
AK4220
9 Q1
Digital 3.3V
0.47u
1 RIN+7
75
External Block
Micro
Controller
GND7 63
0.47u
0.47u
Digital Ground
Video out
Video in
Analog 5V
Figure 29. Typical Connection Diagram
MS0627-E-01
2010/09
- 29 -
[AK4220]
1. Grounding and Power Supply Decoupling
The AK4220 requires careful attention to power supply and grounding arrangements. AVDD, VVDD1-2 and DVDD are
usually supplied from the analog power supply in the system. Alternatively if AVDD, VVDD1-2 and DVDD are supplied
separately, the power up sequence is not critical. AVSS, VVSS1-3 and DVSS must be connected to the analog ground
plane. System analog ground and digital ground should be connected together near to where the supplies are brought onto
the printed circuit board. Decoupling capacitors should be as close to the AK4220 as possible, with the small value
ceramic capacitors being the nearest.
2. Voltage Reference
VCOM is a signal ground of this chip. A 2.2μF electrolytic capacitor in parallel with a 0.1μF ceramic capacitor attached
between VCOM and AVSS eliminates the effects of high frequency noise. No load current may be drawn from VCOM
pin. All signals, especially clocks, should be kept away from VCOM in order to avoid unwanted coupling into the
AK4220. MUTET is an audio output common voltage. A 0.1μF electrolytic capacitor attached between VCOM and
AVSS. No load current may be drawn from MUTET. All signals, especially clocks, should be kept away from MUTET in
order to avoid unwanted coupling into the AK4220.
3. The notes for drawing the board
Analog input and output pins should be as short as possible in order to avoid unwanted coupling into the AK4220. The
unused pins should be open.
4. Video Output
The AK4220 has on-chip 3ch video amp for drive 150Ω resistance and two way to output video signal. One way is using
the Sag Compensation circuit (Figure 30), the other way is using DC output (Figure 31). 100μF and 2.2μF capacitors is
needed for Sag Compensation circuit . It should be shorted VOUT pin and VBF pin using DC output mode. The clamp
level is 600mV(typ) in the DC output mode. Each output way can set by SAGN bit (Table 13).
C3
100uF
VOUT
+6dB
R1
75Ω
C4
2.2uF
R2
75Ω
VFB
Figure 30. Video Block (SAGN bit=“0”, Sag Compensation mode)
R1
75Ω
+6dB
VOUT
R2
75Ω
VFB
Figure 31. Video Block (SAGN bit=“1”, DC Output)
SAGN bit
0
1
Output
Sag Compensation mode
DC output mode
(default)
Table 13. Setting for the video output
MS0627-E-01
2010/09
- 30 -
[AK4220]
PACKAGE
64pin LQFP(Unit: mm)
12.0
Max 1.85
10.0
1.40
0.00~0.25
33
32
48
12.0
49
64
17
16
1
0.2±0.1
0.5
0.09~0.25
0.10 M
0°~10°
0.50±0.25
0.10
■ Package & Lead frame material
Package molding compound:
Lead frame material:
Lead frame surface treatment:
Epoxy
Cu
Solder (Pb free) plate
MS0627-E-01
2010/09
- 31 -
[AK4220]
MARKING
AKM
AK4220VQ
XXXXXXX
1
1) Pin #1 indication
2) Asahi Kasei Logo
3) Marking Code: AK4220VQ
4) Date Code: XXXXXXX (7 digits)
REVISION HISTORY
Date (YY/MM/DD)
07/05/10
10/09/28
Revision
00
01
Reason
First Edition
Error Correction
Page
Contents
19
2. VDER bit
The description was changed.
2. I2C bus control mode
1. WRITE Operation
“001000” → “00100”
most significant 3-bits → 4-bits
PACKAGE
The package dimensions were changed.
23
Specification
Change
31
MS0627-E-01
2010/09
- 32 -
[AK4220]
IMPORTANT NOTICE
z These products and their specifications are subject to change without notice.
When you consider any use or application of these products, please make inquiries the sales office of Asahi Kasei
Microdevices Corporation (AKM) or authorized distributors as to current status of the products.
z Descriptions of external circuits, application circuits, software and other related information contained in this
document are provided only to illustrate the operation and application examples of the semiconductor products. You
are fully responsible for the incorporation of these external circuits, application circuits, software and other related
information in the design of your equipments. AKM assumes no responsibility for any losses incurred by you or third
parties arising from the use of these information herein. AKM assumes no liability for infringement of any patent,
intellectual property, or other rights in the application or use of such information contained herein.
z Any export of these products, or devices or systems containing them, may require an export license or other official
approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange,
or strategic materials.
z AKM products are neither intended nor authorized for use as critical componentsNote1) in any safety, life support, or
other hazard related device or systemNote2), and AKM assumes no responsibility for such use, except for the use
approved with the express written consent by Representative Director of AKM. As used here:
Note1) A critical component is one whose failure to function or perform may reasonably be expected to result,
whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and
which must therefore meet very high standards of performance and reliability.
Note2) A hazard related device or system is one designed or intended for life support or maintenance of safety
or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or
perform may reasonably be expected to result in loss of life or in significant injury or damage to person or
property.
z It is the responsibility of the buyer or distributor of AKM products, who distributes, disposes of, or otherwise places
the product with a third party, to notify such third party in advance of the above content and conditions, and the buyer
or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless from any and all
claims arising from the use of said product in the absence of such notification.
MS0627-E-01
2010/09
- 33 -