DIOTEC ELECTRONICS CORPORATION GENERAL PURPOSE, FAST RECOVERY, and HIGH VOLTAGE DIODE PRODUCT GUIDE TRUE VOID FREE VACUUM DIE SOLDERING SOFT GLASS DIODES® HIGH VOLTAGE ULTRA FAST RECOVERY DISH DIODES TVS PRESS FIT WEB SITE: www.diotec-usa.com E-MAIL: [email protected] DIOTEC ELECTRONICS CORP. THE RECTIFIER SPECIALISTS THE ONLY QUALITY DIODES AND RECTIFIERS AT COMPETITIVE PRICES 18020 HOBART BLVD, UNIT B GARDENA, CALIFORNIA 90248 USA TEL: 310 - 767 - 1052 FAX: 310 - 767 - 7958 EMAIL: [email protected] WEB SITE: www.diotec-usa.com DIOTEC ELECTRONICS CORPORATION 18020 HOBART BLVD. GARDENA, CA 90248 USA PH: 310-767-1052 FX: 310-767-7958 E-MAIL: [email protected] WEB SITE: www.diotec-usa.com EVER WONDER WHY SOME DIODES DIE PREMATURELY .…. WITHOUT OBVIOUS CAUSE Most Likely It's The Invisible Killer ….. DIE ATTACH SOLDER VOIDS This invisible problem is much, much, more serious, and a lot more common than you might think. In the photographs below, diodes produced by a prestigious multinational semiconductor manufacturer were examined for die solder quality. These diodes were provided by one of our potential customers who have experienced serious quality problems and premature failures. This set of photos illustrates a very common situation when a diode is pried open LARGE VOID AREA REVEALED IN THE SOLDER LAYER SECTION B SECTION A NUMEROUS SOLDER VOIDS CAN CLEARLY BE SEEN IN THESE CLOSE UPS. These Voids 1) Greatly Weaken The Diode's Mechanical Integrity, 2) Increase The Forward Voltage Drop, and 3) Severely Restrict The Dissipation of Heat From The Die. Restricted Heat Dissipation causes the Diode to Operate at Elevated Temperatures Which Could Lower Its Current Handling and/or Cause Premature Failure. This set of photographs illustrates another common, but much more serious, situation. Here the diode is pried open and separates completely at the die solder layer ONLY SOLDER IN SECTION B CHIP IS INTACT IN SECTION A SOLDER COVERS ~ 50% OF DIE SECTION B - ONLY SOLDER SECTION A- DIE SIDE The Solder Either Failed to Wet And, Hence, Bond to The Die's Surface (Surface Outlined in Red on Section B) or is riddled with voids. As a Result, This Diode Has Absolutely No Mechanical Strength And May Fail On Impact if dropped or Struck. Additionally, The Thermal Resistance of This Diode is so High that Thermal Runaway is a Certainty. See The DIOTEC Difference - VOID FREE DIE SOLDERING. Copyright 2001 DIOTEC Electronics Corporation. All rights reserved DIOTEC ELECTRONICS CORPORATION This is the DIOTEC difference. BREAKS AT SILICON DIE NO VISIBLE VOIDS. SECTION A SECTION B Superior Soldering Results in SUPERIOR MECHANICAL STRENGTH, SUPERB HEAT DISSIPATION, and LOWER FORWARD VOLTAGE DROP DIOTEC utilizes an advanced, computer controlled, vacuum die soldering process, which enables silicon chips to be soldered to metal with exceptional consistency and void free quality. Thus, DIOTEC diodes and bridge rectifiers have unmatched heat dissipation, cooler junction temperatures, lower leakage currents, and reduced thermal stress. Additionally, the high quality die attachment allows the diodes survive mechanical shock without bond failure, another common problem with most offshore "cheap" diodes. SHOULD YOU WANT: • Want to discuss this topic further? • A free analysis similar to that shown here to determine the quality of the diodes you are now using? We'll tell it like we see it and return your items with the pictures so you can see for yourself. • Wish to put us to the test in your environment? Request product samples Please don't hesitate to contact: JOE LIN or DEAN LIGOCKI PH: 310-767-1052 FX: 310-767-7958 [email protected] [email protected] DIOTEC ELECTRONICS CORPORATION THE ONLY HIGH QUALITY DIODES & RECTIFIERS AT COMPETITIVE PRICES Copyright 2001 DIOTEC Electronics Corporation. All rights reserved DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 Every effort has been made to ensure that the information contained herein is current, accurate, and of the necessary detail to support the component or design engineer. It is recognized that a standard product can not satisfy every application requirement. If your requirements fall in this category, do not hesitate to call, fax, or e-mail our technical staff. We are here to help you! DIOTEC is dedicated to furnishing the highest quality products at the most competitive cost. Thus, product changes to improve reliability, function, and design may be made without notice. The information in this data book has been carefully reviewed and is believed to be accurate. However, no responsibility is assumed for inaccuracies. Before committing to a design, it is recommended that the designer request product samples to validate the operational characteristics and performance in the actual application. DIOTEC does not imply any warranty, or assume any liability from the application or use of any product or circuit described in this catalog. DIOTEC does not recommend the use of its products in applications where a failure/malfunction of the product may directly threaten life or injury. The user of DIOTEC's products in life support application assumes all risks of such use and indemnifies DIOTEC Electronics Corp. against all damages. GENERAL PURPOSE AND FAST RECOVERY DIODES GENERAL PURPOSE DIODES 1-6 AMPERES 50 to 1000 VOLTS DO - 41 DO - 27 ULTRA FAST SWITCHING DIODES 0.150 AMPERES 75 VOLTS DO - 35 FAST RECOVERY SILICON DIODES 1-8 AMPERES 50 to 1000 VOLTS DO - 41 DO - 27 G-6A TO-220AC DIOTEC ELECTRONICS CORP. - 18020 Hobart Blvd., Unit B - Gardena, CA 90248 U.S.A. - PH: 310-767-1052 - FX: 310-767-7958 GENERAL PURPOSE SILICON DIODE QUICK SELECTION GUIDE SEE SECTION H DIOTEC's offers a number of axial lead, low cost, general purpose diodes which will satisfy a wide range of applications. A number these diodes are available as DIOTEC's SOFT GLASS DIODES (SOFT GLASS DIODE is a DIOTEC Registered Trademark). These SOFT GLASS DIODES provide the highest degree of operational reliability, efficiency, and high temperature/mechanical stress reliability. More information on SOFT GLASS DIODES may be found in Appendix X. IO, AVERAGE RECTIFIED FORWARD CURRENT (AMPERES) VRRM 1 1.5 DO-41 DO-15 2 3 DO-41 SOFT GLASS DIODES SOFT GLASS DIODES 4 6 DO-27 DO-27 SOFT GLASS DIODES 50 1N4001 1N4001G GP100 S1A 1N5391 GP200 IN5400 1N5400G GP400 GP600 100 1N4002 1N4002G GP101 S1B 1N5392 GP201 IN5400 1N5400G GP401 GP601 200 1N4003 1N4003G GP102 S1D 1N5393 GP202 IN5400 1N5400G GP402 GP602 400 1N4004 1N4004G GP104 S1G 1N5395 GP204 IN5400 1N5400G GP404 GP604 600 1N4005 1N4005G GP106 S1J 1N5397 GP206 IN5400 1N5400G GP406 GP606 800 1N4006 1N4006G GP108 S1K 1N5398 GP208 IN5400 1N5400G GP408 GP608 1000 1N4007 1N4007G GP110 S1M 1N5399 GP210 IN5400 1N5400G GP410 GP610 IFSM (Amps) 50 50 50 30 60 70 200 200 200 400 TA @ Rated IO (oC) 75 75 75 75 50 75 75 75 75 TJ (Max) (oC) 175 175 175 175 175 175 175 100 Note 1 175 175 150 O NOTES: (1) Temperature Rating: TL=100 C PART NUMBERING SYSTEM Example: GP102 (1 Amp, 200 Volt, Axial Lead General Purpose SOFT GLASS DIODE (SOFT GLASS DIODE is a DIOTEC Electronics Registered Trademark) GP A VV Blocking Voltage Reference (50 - 1000 Volts) - 2 Digits. Examples: 02 = 200 Volts; 10 = 1000 Volts Current Reference (Average Forward Rectified Current) - 1 Digit. Soft Glass, General Purpose Diode Designator (See Note) NOTE: The Single Exception to This System is The GP600 Series of Diodes. These diodes are ARE NOT SOFT GLASS DIODES. 1N4000, 1N5391, 1N5400 - JEDEC Type Designation 1N4000G, 1N5400G - DIOTEC SOFT GLASS Equivalent of the JEDEC Type Designated Diode DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd. Unit B Gardena, CA 90248 PH: 310-767-1052 FX: 310-767-7958 e-mail: [email protected] xi FAST RECOVERY SILICON DIODE QUICK SELECTION GUIDE SEE SECTION H DIOTEC's Fast Recovery Diodes exhibit switching times in the range of 4 to 500nS. Additionally, many of these products are SOFT GLASS DIODES (SOFT GLASS DIODE is a DIOTEC Registered Trademark). These SOFT GLASS DIODES provide the highest degree of operational efficiency and high temperature/mechanical stress reliability. More information on SOFT GLASS DIODES may be found in Appendix X. IO, AVERAGE RECTIFIED FORWARD CURRENT (AMPERES) 0.15 1 2 3 6 8 DO-27 G-6A TO-220AC DO-41 DO-35 DO-41 VRRM SOFT GLASS DIODES SOFT GLASS DIODES 50 1N4933 RP100 RGP100 RGP200 RP300 RGP300 RP600 RGP800 1N4934 RP101 RGP101 RGP201 RP301 RGP301 RP601 RGP801 200 1N4935 RP102 RGP102 RGP202 RP302 RGP302 RP602 RGP802 400 1N4936 RP104 RGP104 RGP204 RP304 RGP304 RP604 RGP804 600 1N4937 RP106 RGP106 RGP206 RP306 RGP306 RP606 RGP806 800 RP108 RGP108 RGP208 RP308 RGP308 RP608 1000 RP110 RGP110 RGP210 RP310 RGP310 RP610 30 50 60 200 200 300 100 IFSM (Amps) 1N4148 (Note 1) Note 2 30 T C @ Rated IO (oC) 150 110 TA @ Rated IO (oC) 75 75 75 75 75 55 55 60 TJ (Max) (oC) 175 175 175 175 175 175 175 175 T RR (nS) 4 200 TRR = 150nS: 0 < VRRM < 500; TRR = 250nS: 500 < VRRM < 700; TRR = 500nS: 700 < VRRM <1100 (Note 3) 150 Note 4 NOTES: ( 1 ) VRRM =75VOLTS (2)ULTRA FAST SWITCHING DIODE: @ PULSE WIDTH OF 1 S e c , I FSM = 1 Amp; @ PULSE WIDTH OF 1 µSec, IFSM = 4 Amps (3)300nSAVAILABLE, CONSULT FACTORY (4)FOR 0< VRRM <300, T RR = 150 n S ; 3 0 0 < VRRM <500, T RR =200 nS; 500< VRRM <650 TRR = 250 n S PART NUMBERING SYSTEM Example: RP102 or RGP102 (1 Amp, 200 Volt, Axial Lead Fast Recovery Diode; The Second Product (RGP102) is a SOFT GLASS DIODE R ) R(G)P A VV Blocking Voltage Reference (50 - 1000 Volts) - 2 Digits. Examples: 02 = 200 Volts; 10 = 1000 Volts Current Reference (Average Forward Rectified Current) - 1 Digit. Fast Recovery Diode Designator; With the "G" Present, Indicates That This Product is a SOFT GLASS DIODE NOTE: The Single Exception to This System is The RGP800 Series of Fast Recovery Diodes. These diodes are provided in a TO-220AC Package. Additionally, These Products ARE NOT SOFT GLASS DIODES. 1N4148, 1N4933 - JEDEC Type Designation xii DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd. Unit B Gardena, CA 90248 PH: 310-767-1052 FX: 310-767-7958 e-mail: [email protected] DIOTEC ELECTRONICS CORP. Data Sheet No. GPDP-101-1B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 MECHANICAL SPECIFICATION FEATURES ACTUAL SIZE OF DO-41 PACKAGE Low cost SERIES 1N4001 - 1N4007 DO - 41 Low leakage LL Low forward voltage drop BD (Dia) High current capacity BL Easily cleaned with freon, alcohol, chlorothene and similar solvents Color Band Denotes Cathode MECHANICAL DATA LL Case: JEDEC DO-41, molded plastic (U/L Flammability Rating 94V-0) Terminals: Plated axial leads LD (Dia) Soldering: Per MIL-STD 202 Method 208 guaranteed Minimum In mm Sym Polarity: Color band denotes cathode BL Mounting Position: Any BD Weight: 0.012 Ounces (0.34 Grams) LL LD Maximum In mm 4.1 0.205 5.2 0.103 2.6 0.107 2.7 1.00 0.028 25.4 0.71 0.034 0.86 0.160 MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%. PARAMETER (TEST CONDITIONS) RATINGS SYMBOL Series Number 1N4001 1N4002 1N4003 1N4004 1N4005 1N4006 1N4007 Maximum DC Blocking Voltage VRM 50 Maximum RMS Voltage VRMS Maximum Peak Recurrent Reverse Voltage VRRM Average Forward Rectified Current @ TA = 75 oC (Lead length = 0.375 in. (9.5 mm)) Peak Forward Surge Current (8.3 mSec single half sine wave superimposed on rated load) Maximum Forward Voltage at 1 Amp DC Maximum Full Cycle Reverse Current @ TL = 75 oC (Note 1) Maximum Average DC Reverse Current At Rated DC Blocking Voltage @ TA = 25oC o @ TA = 100 C Typical Thermal Resistance, Junction to Ambient (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range NOTES: (1) Lead length = 0.375 in. (9.5 mm) (2) Measured at 1MHz & applied reverse voltage of 4 volts UNITS 1000 100 200 400 600 800 35 70 140 280 420 560 700 50 100 200 400 600 800 1000 IO 1 IFSM 50 VFM 1 IRM(AV) 30 IRM 5 50 RθJA 30 VOLTS AMPS VOLTS µA °C/W CJ 26 pF TJ, TSTG -65 to +175 °C 4.97fgpdp101 H1 DIOTEC ELECTRONICS CORP. Data Sheet No. GPDP-101-2B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 1 AMP GENERAL PURPOSE SILICON DIODES RATING & CHARACTERISTIC CURVES FOR SERIES 1N4001 - 1N4007 50 40 30 Single Phase, Half wave, 60 Hz Resistive and Inductive Loads Lead Length = 0.375" (9.5 mm) 20 JEDEC Method 8.3 mS Half Sine Wave 10 Ambient Temperature, o C 0 10 1 FIGURE 1. FORWARD CURRENT DERATING CURVE 100 Number of Cycles at 60 Hz FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT 10 10 TJ = 100 oC 1.0 1.0 0.1 0.1 TJ = 25 oC TJ = 25 oC Pulse Width = 300 µS 1% Duty Cycle .01 20 0.01 60 80 100 120 140 Percent of Rated Peak Reverse Voltage Instantaneous Forward Voltage (Volts) FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE 100 FIGURE 4. TYPICAL REVERSE CHARACTERISTICS 1000 o TJ = 25 C T J = 25 oC 10 100 TJ = 25 oC Non-repetitive Square Pulse di/dt =200 µS 0.1 0.1 1 10 100 Reverse Voltage, (Volts) FIGURE 5. TYPICAL JUNCTION CAPACITANCE PER DIODE H2 10 0.01 0.1 1.0 10 Pulse Duration (Milliseconds) FIGURE 6. PEAK FORWARD SURGE CURRENT 4.97bgpdp101 DIOTEC ELECTRONICS CORP. Data Sheet No. GPPD-100-1B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 MECHANICAL SPECIFICATION FEATURES R PROPRIETARY SOFT GLASS JUNCTION PASSIVATION FOR SUPERIOR RELIABILITY AND PERFORMANCE ACTUAL SIZE OF DO-41 PACKAGE SERIES 1N4001G - 1N4007G DO - 41 VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM MECHANICAL STRENGTH AND HEAT DISSIPATION (Solder Voids: Typical < 2%, Max. < 10% of Die Area) LL BD (Dia) EXTREMELY LOW LEAKAGE AT HIGH TEMPERATURES LOW FORWARD VOLTAGE DROP BL Color Band Denotes Cathode 1A at TA = 75 oC WITH NO THERMAL RUNAWAY MECHANICAL DATA LL Case: JEDEC DO-41, molded plastic (U/L Flammability Rating 94V-0) Terminals: Plated axial leads LD (Dia) Soldering: Per MIL-STD 202 Method 208 guaranteed Minimum In mm Sym Polarity: Color band denotes cathode BD Weight: 0.012 Ounces (0.34 Grams) LL LD 4.1 0.205 5.2 0.103 2.6 0.107 2.7 1.00 0.028 25.4 0.71 0.034 0.86 0.160 BL Mounting Position: Any Maximum In mm MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%. PARAMETER (TEST CONDITIONS) RATINGS SYMBOL 1N 1N 1N 1N 1N 1N 1N 4001G 4002G 4003G 4004G 4005G 4006G 4007G Series Number Maximum DC Blocking Voltage VRM 50 Maximum RMS Voltage VRMS Maximum Peak Recurrent Reverse Voltage VRRM Average Forward Rectified Current @ TA = 75 oC (Lead length = 0.375 in. (9.5 mm)) Peak Forward Surge Current ( 8.3 mSec single half sine wave superimposed on rated load) Maximum Forward Voltage at 1 Amp DC Maximum Full Cycle Reverse Current @ TL = 75 oC (Note 1) Maximum Average DC Reverse Current At Rated DC Blocking Voltage @ TA = 25oC o @ TA = 100 C Typical Thermal Resistance, Junction to Ambient (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range NOTES: (1) Lead length = 0.375 in. (9.5 mm) (2) Measured at 1MHz & applied reverse voltage of 4 volts UNITS 1000 100 200 400 600 800 35 70 140 280 420 560 700 50 100 200 400 600 800 1000 IO 1 IFSM 50 VFM 1 IRM(AV) 10 IRM 1 20 RθJA 30 VOLTS AMPS VOLTS µA °C/W CJ 10 pF TJ, TSTG -65 to +175 °C 4.97fgppd100 H3 DIOTEC ELECTRONICS CORP. Data Sheet No. GPPD-100-2B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 1 AMP SOFT GLASS PASSIVATED SILICON DIODES RATING & CHARACTERISTIC CURVES FOR SERIES 1N4001G - 1N4007G 50 40 30 Single Phase, Half wave, 60 Hz Resistive and Inductive Loads Lead Length = 0.375" (9.5 mm) 20 JEDEC Method 8.3 mS Half Sine Wave 10 Ambient Temperature, o C 0 1 FIGURE 1. FORWARD CURRENT DERATING CURVE 10 100 Number of Cycles at 60 Hz FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT 10 10 TJ = 100 oC 1.0 1.0 0.1 TJ = 25 oC 0.1 TJ = 25 oC Pulse Width = 300 µS 1% Duty Cycle .01 20 0.01 60 80 100 120 140 Percent of Rated Peak Reverse Voltage Instantaneous Forward Voltage (Volts) FIGURE 4. TYPICAL REVERSE CHARACTERISTICS FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE 100 1000 o TJ = 25 C T J = 25 oC 10 100 TJ = 25 oC Non-repetitive Square Pulse di/dt =200 µS 0.1 0.1 1 10 100 Reverse Voltage, (Volts) FIGURE 5. TYPICAL JUNCTION CAPACITANCE PER DIODE H4 10 0.01 0.1 1.0 10 Pulse Duration (Milliseconds) FIGURE 6. PEAK FORWARD SURGE CURRENT 4.97bgppd100 DIOTEC ELECTRONICS CORP. Data Sheet No. GPDG-101-1B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 MECHANICAL SPECIFICATION FEATURES R PROPRIETARY SOFT GLASS JUNCTION PASSIVATION FOR SUPERIOR RELIABILITY AND PERFORMANCE ACTUAL SIZE OF DO-41 PACKAGE SERIES GP100 - GP110 DO - 41 VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM MECHANICAL STRENGTH AND HEAT DISSIPATION (Solder Voids: Typical < 2%, Max. < 10% of Die Area) LL BD (Dia) EXTREMELY LOW LEAKAGE AT HIGH TEMPERATURES LOW FORWARD VOLTAGE DROP BL Color Band Denotes Cathode 1A at TA = 75 oC WITH NO THERMAL RUNAWAY MECHANICAL DATA LL Case: JEDEC DO-41, molded silica glass (U/L Flammability Rating 94V-0) Terminals: Plated axial leads LD (Dia) Soldering: Per MIL-STD 202 Method 208 guaranteed Minimum In mm Sym Polarity: Color band denotes cathode BD Weight: 0.012 Ounces (0.34 Grams) LL LD 4.1 0.205 5.2 0.103 2.6 0.107 2.7 1.00 0.028 25.4 0.71 0.034 0.86 0.160 BL Mounting Position: Any Maximum In mm MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%. PARAMETER (TEST CONDITIONS) RATINGS SYMBOL GP100 GP101 GP102 GP104 GP106 GP108 GP110 Series Number Maximum DC Blocking Voltage VRM 50 Maximum RMS Voltage VRMS Maximum Peak Recurrent Reverse Voltage VRRM Average Forward Rectified Current @ TA = 75 oC, Lead length = 0.375 in. (9.5 mm) Peak Forward Surge Current ( 8.3 mSec single half sine wave superimposed on rated load) Maximum Forward Voltage at 1 Amp DC Maximum Full Cycle Reverse Current @ TL = 75 oC (Note 1) Maximum Average DC Reverse Current At Rated DC Blocking Voltage @ TA = 25oC o @ TA = 125 C Typical Thermal Resistance, Junction to Ambient (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range NOTES: (1) Lead length = 0.375 in. (9.5 mm) (2) Measured at 1MHz & applied reverse voltage of 4 volts UNITS 1000 100 200 400 600 800 35 70 140 280 420 560 700 50 100 200 400 600 800 1000 IO 1 IFSM 50 VFM 1 VOLTS AMPS IRM(AV) 5 IRM 0.5 30.0 RθJA 30 VOLTS µA °C/W CJ 10 pF TJ, TSTG -65 to +175 °C 4.97fgpdg101 H5 DIOTEC ELECTRONICS CORP. Data Sheet No. GPDG-101-2B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 1 AMP HIGH RELIABILITY SILICON DIODES RATING & CHARACTERISTIC CURVES FOR SERIES GP100 - GP110 50 40 30 Single Phase, Half wave, 60 Hz Resistive and Inductive Loads Lead Length = 0.375" (9.5 mm) 20 JEDEC Method 8.3 mS Half Sine Wave 10 Ambient Temperature, o C 0 10 1 FIGURE 1. FORWARD CURRENT DERATING CURVE 100 Number of Cycles at 60 Hz FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT 10 10 TJ = 100 oC 1.0 1.0 0.1 TJ = 25 oC 0.1 TJ = 25 oC Pulse Width = 300 µS 1% Duty Cycle .01 20 60 80 100 120 140 0.01 Percent of Rated Peak Reverse Voltage Instantaneous Forward Voltage (Volts) FIGURE 4. TYPICAL REVERSE CHARACTERISTICS FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE 100 1000 o TJ = 25 C T J = 25 oC 10 100 TJ = 25 oC Non-repetitive Square Pulse di/dt =200 µS 0.1 0.1 1 10 100 Reverse Voltage, (Volts) FIGURE 5. TYPICAL JUNCTION CAPACITANCE PER DIODE H6 10 0.01 0.1 1.0 10 Pulse Duration (Milliseconds) FIGURE 6. PEAK FORWARD SURGE CURRENT 4.97bgpdg101 DIOTEC ELECTRONICS CORP. Data Sheet No. GPDP-151-1B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 MECHANICAL SPECIFICATION FEATURES ACTUAL SIZE OF DO-15 PACKAGE Low cost SERIES 1N5391 - 1N5399 DO - 15 Low leakage LL Low forward voltage drop BD (Dia) High current capacity BL Easily cleaned with freon, alcohol, chlorothene and similar solvents Color Band Denotes Cathode MECHANICAL DATA LL Case: JEDEC DO-15 molded plastic (U/L Flammability Rating 94V-0) Terminals: Plated axial leads LD (Dia) Soldering: Per MIL-STD 202 Method 208 guaranteed Minimum In mm Sym Polarity: Color band denotes cathode BL Mounting Position: Any BD Weight: 0.01 Ounces (0.4 Grams) LL LD Maximum In mm 6.01 0.255 6.48 0.130 3.3 0.140 3.6 1.00 0.028 25.4 0.71 0.034 0.86 0.240 MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%. PARAMETER (TEST CONDITIONS) RATINGS SYMBOL Series Number 1N5391 1N5392 1N5393 1N5395 1N5397 1N5398 1N5399 Maximum DC Blocking Voltage VRM 50 Maximum RMS Voltage VRMS Maximum Peak Recurrent Reverse Voltage VRRM Average Forward Rectified Current @ TA = 75 oC, Lead length = 0.375 in. (9.5 mm) Peak Forward Surge Current ( 8.3 mSec single half sine wave superimposed on rated load) Maximum Forward Voltage at 1.5 Amps DC Maximum Full Cycle Reverse Current @ TL = 75 oC (Note 1) Maximum Average DC Reverse Current At Rated DC Blocking Voltage @ TA = 25oC o @ TA = 100 C Typical Thermal Resistance, Junction to Ambient (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range NOTES: (1) Lead length = 0.375 in. (9.5 mm) (2) Measured at 1MHz & applied reverse voltage of 4 volts UNITS 1000 100 200 400 600 800 35 70 140 280 420 560 700 50 100 200 400 600 800 1000 IO 1.5 IFSM 60 VFM 1 IRM(AV) 30 IRM 5 50 RθJA 50 VOLTS AMPS VOLTS µA °C/W CJ 30 pF TJ, TSTG -65 to +175 °C 4.97fgpdp151 H9 DIOTEC ELECTRONICS CORP. Data Sheet No. GPDP-151-2B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 1.5 AMP GENERAL PURPOSE SILICON DIODES RATING & CHARACTERISTIC CURVES FOR SERIES 1N5391 - 1N5399 75 60 45 30 15 Ambient Temperature, o C 0 10 1 FIGURE 1. FORWARD CURRENT DERATING CURVE 100 Number of Cycles at 60 Hz FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT 10 10 TJ = 100 oC 1.0 1.0 0.1 0.1 TJ = 25 oC .01 0.01 Instantaneous Forward Voltage (Volts) 20 60 80 100 120 140 Percent of Rated Peak Reverse Voltage FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE FIGURE 4. TYPICAL REVERSE CHARACTERISTICS 100 TJ = 25 oC 10 0.1 0.1 1 10 100 Reverse Voltage, (Volts) FIGURE 5. TYPICAL JUNCTION CAPACITANCE PER DIODE H10 4.97bgpdp151 DIOTEC ELECTRONICS CORP. Data Sheet No. GPPD-200-1B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 MECHANICAL SPECIFICATION FEATURES R PROPRIETARY SOFT GLASS JUNCTION PASSIVATION FOR SUPERIOR RELIABILITY AND PERFORMANCE ACTUAL SIZE OF DO-41 PACKAGE SERIES GP200 - GP210 DO - 41 VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM MECHANICAL STRENGTH AND HEAT DISSIPATION (Solder Voids: Typical < 2%, Max. < 10% of Die Area) LL BD (Dia) EXTREMELY LOW LEAKAGE AT HIGH TEMPERATURES LOW FORWARD VOLTAGE DROP BL Color Band Denotes Cathode 1A at TA = 75 oC WITH NO THERMAL RUNAWAY MECHANICAL DATA LL Case: JEDEC DO-41 molded plastic (U/L Flammability Rating 94V-0) Terminals: Plated axial leads LD (Dia) Soldering: Per MIL-STD 202 Method 208 guaranteed Polarity: Color band denotes cathode Minimum In mm Sym 0.160 BL Mounting Position: Any Weight: 0.01 Ounces (0.4 Grams) Maximum In mm 4.1 0.205 5.2 BD 0.103 2.6 0.107 2.7 LL LD 1.00 0.028 25.4 0.71 0.034 0.86 MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%. PARAMETER (TEST CONDITIONS) RATINGS SYMBOL UNITS GP200 GP201 GP202 GP204 GP206 GP208 GP210 Series Number Maximum DC Blocking Voltage VRM 50 100 200 400 600 800 1000 Maximum RMS Voltage VRMS 35 70 140 280 420 560 700 Maximum Peak Recurrent Reverse Voltage VRRM 50 100 200 400 600 800 1000 Average Forward Rectified Current @ TA = 75 oC, Lead length = 0.375 in. (9.5 mm) Peak Forward Surge Current ( 8.3 mSec single half sine wave superimposed on rated load) IO 2 IFSM 70 Maximum Forward Voltage at 2 Amps DC VFM 1.1 Maximum Reverse Recovery Time (IF=0.5A, IR=1A, IRR=0.25A) TRR 30 IRM 5 50 Maximum Average DC Reverse Current At Rated DC Blocking Voltage Typical Junction Capacitance (Note 1) Operating and Storage Temperature Range NOTES: (1) Measured at 1MHz & applied reverse voltage of 4 volts (2) 300 nS available - consult factory @ TA = 25oC @ TA = 100oC VOLTS AMPS VOLTS µA CJ 40 pF TJ, TSTG -65 to +175 °C 4.97 fgppd200 H11 DIOTEC ELECTRONICS CORP. Data Sheet No. GPPD-200-2B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 2 AMP SOFT GLASS PASSIVATED SILICON DIODES RATING & CHARACTERISTIC CURVES FOR SERIES GP200 - GP210 100 80 60 40 20 Ambient Temperature, o C 0 10 1 FIGURE 1. FORWARD CURRENT DERATING CURVE 100 Number of Cycles at 60 Hz FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT 10 10 TJ = 100 oC 1.0 1.0 0.1 0.1 TJ = 25 oC .01 0.01 Instantaneous Forward Voltage (Volts) 20 60 80 100 120 140 Percent of Rated Peak Reverse Voltage FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE 100 TJ = 25 oC 10 0.1 0.1 1 10 100 Reverse Voltage, (Volts) FIGURE 5. TYPICAL JUNCTION CAPACITANCE PER DIODE H12 4.97bgpdp2 DIOTEC ELECTRONICS CORP. Data Sheet No. GPDP-301-1B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 MECHANICAL SPECIFICATION FEATURES ACTUAL SIZE OF DO-27 PACKAGE Low cost SERIES 1N5400 - IN5408 DO - 27 Low leakage LL Low forward voltage drop BD (Dia) High current capacity BL Easily cleaned with freon, alcohol, chlorothene and similar solvents Color Band Denotes Cathode MECHANICAL DATA LL Case: JEDEC DO-27 molded plastic (U/L Flammability Rating 94V-0) Terminals: Plated axial leads LD (Dia) Soldering: Per MIL-STD 202 Method 208 guaranteed Sym Polarity: Color band denotes cathode Minimum In mm Maximum In mm BL 0.365 9.28 Mounting Position: Any BD 0.205 5.2 Weight: 0.02 Ounces (0.7 Grams) LL LD 0.052 1.3 1.00 0.048 25.4 1.2 MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%. PARAMETER (TEST CONDITIONS) RATINGS SYMBOL Series Number 1N5400 1N5401 1N5402 1N5404 1N5406 1N5407 1N5408 Maximum DC Blocking Voltage VRM 50 Maximum RMS Voltage VRMS Maximum Peak Recurrent Reverse Voltage VRRM Average Forward Rectified Current @ TA = 75 oC Lead length = 0.375 in. (9.5 mm) Peak Forward Surge Current ( 8.3 mSec single half sine wave superimposed on rated load) Maximum Forward Voltage at 3 Amps DC Maximum Full Cycle Reverse Current @ TL = 75 oC (Note 1) Maximum Average DC Reverse Current At Rated DC Blocking Voltage @ TA = 25oC o @ TA = 100 C Typical Thermal Resistance, Junction to Ambient (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range NOTES: (1) Lead length = 0.375 in. (9.5 mm) (2) Measured at 1MHz & applied reverse voltage of 4 volts UNITS 1000 100 200 400 600 800 35 70 140 280 420 560 700 50 100 200 400 600 800 1000 IO 3 IFSM 200 VFM 1 IRM(AV) 30 IRM 5 50 RθJA 18 VOLTS AMPS VOLTS µA °C/W CJ 70 pF TJ, TSTG -65 to +175 °C 4.97fgpdp301 H13 DIOTEC ELECTRONICS CORP. Data Sheet No. GPDP-301-2B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 3 AMP GENERAL PURPOSE SILICON DIODES RATING & CHARACTERISTIC CURVES FOR SERIES 1N5400 - 1N5408 RESISTIVE OR INDUCTIVE LOADS 1000 Maximum Non-repetitive 100 o TJ = 25 C NOTE 1 Maximum Repetitive 10 1 10 o Ambient Temperature, C 100 Number of Cycles at 60Hz FIGURE 1. FORWARD CURRENT DERATING CURVE FIGURE 2. FORWARD SURGE CURRENT 100 10 10 1.0 1.0 0.1 TJ = 25 oC 0.1 .01 20 60 80 100 120 140 Percent of Rated Peak Reverse Voltage 0.01 FIGURE 4. TYPICAL REVERSE CHARACTERISTICS Instantaneous Forward Voltage (Volts) FIGURE 3. TYPICAL FORWARD CHARACTERISTICS 100 TJ = 25 oC NOTES (1) Single Phase, Half Wave, 60 Hz; Lead Length = 0.375" (9.5mm) (2) TJ = 25 oC, Pulse Width = 300 µ Sec, 1.0% Duty Cycle 10 0.1 0.1 1 10 100 Reverse Voltage, (Volts) FIGURE 5. TYPICAL JUNCTION CAPACITANCE H14 4.97bgpdp301 DIOTEC ELECTRONICS CORP. Data Sheet No. GPPD-300-1B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 MECHANICAL SPECIFICATION FEATURES R PROPRIETARY SOFT GLASS JUNCTION PASSIVATION FOR SUPERIOR RELIABILITY AND PERFORMANCE ACTUAL SIZE OF DO-27 PACKAGE SERIES 1N5400G - IN5408G DO - 27 VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM MECHANICAL STRENGTH AND HEAT DISSIPATION (Solder Voids: Typical < 2%, Max. < 10% of Die Area) LL BD (Dia) EXTREMELY LOW LEAKAGE AT HIGH TEMPERATURES LOW FORWARD VOLTAGE DROP BL Color Band Denotes Cathode 3A at TA = 75 oC WITH NO THERMAL RUNAWAY MECHANICAL DATA LL Case: JEDEC DO-27 molded plastic (U/L Flammability Rating 94V-0) Terminals: Plated axial leads LD (Dia) Soldering: Per MIL-STD 202 Method 208 guaranteed Minimum In mm Sym Polarity: Color band denotes cathode Maximum In mm BL 0.365 9.28 Mounting Position: Any BD 0.205 5.2 Weight: 0.02 Ounces (0.7 Grams) LL LD 0.052 1.3 1.00 0.048 25.4 1.2 MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%. PARAMETER (TEST CONDITIONS) RATINGS SYMBOL 1N 1N 1N 1N 1N 1N 1N 5400G 5401G 5402G 5404G 5406G 5407G 5408G Series Number Maximum DC Blocking Voltage VRM 50 Maximum RMS Voltage VRMS Maximum Peak Recurrent Reverse Voltage VRRM Average Forward Rectified Current @ TA = 75 oC (Lead length = 0.375 in. (9.5 mm)) Peak Forward Surge Current (8.3 mSec single half sine wave superimposed on rated load) Maximum Forward Voltage at 3 Amps DC Maximum Full Cycle Reverse Current @ TL = 75 oC (Note 1) Maximum Average DC Reverse Current At Rated DC Blocking Voltage @ TA = 25oC o @ TA = 100 C Typical Thermal Resistance, Junction to Ambient (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range NOTES: (1) Lead length = 0.375 in. (9.5 mm) (2) Measured at 1MHz & applied reverse voltage of 4 volts UNITS 1000 100 200 400 600 800 35 70 140 280 420 560 700 50 100 200 400 600 800 1000 IO 3 IFSM 200 VFM 1 IRM(AV) 20 IRM 2 50 RθJA 18 VOLTS AMPS VOLTS µA °C/W CJ 70 pF TJ, TSTG -65 to +175 °C 4.97fgppd300 H15 DIOTEC ELECTRONICS CORP. Data Sheet No. GPPD-300-2B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 3 AMP SOFT GLASS PASSIVATED SILICON DIODES RATING & CHARACTERISTIC CURVES FOR SERIES 1N5400G - 1N5408G RESISTIVE OR INDUCTIVE LOADS 1000 Maximum Non-repetitive 100 o TJ = 25 C NOTE 1 Maximum Repetitive 10 1 10 100 o Ambient Temperature, C Number of Cycles at 60Hz FIGURE 1. FORWARD CURRENT DERATING CURVE FIGURE 2. FORWARD SURGE CURRENT 100 10 10 1.0 1.0 0.1 TJ = 25 oC 0.1 .01 20 60 80 100 120 140 Percent of Rated Peak Reverse Voltage 0.01 FIGURE 4. TYPICAL REVERSE CHARACTERISTICS Instantaneous Forward Voltage (Volts) FIGURE 3. TYPICAL FORWARD CHARACTERISTICS 100 TJ = 25 oC NOTES (1) Single Phase, Half Wave, 60 Hz; Lead Length = 0.375" (9.5mm) (2) TJ = 25 oC, Pulse Width = 300 µ Sec, 1.0% Duty Cycle 10 0.1 0.1 1 10 100 Reverse Voltage, (Volts) FIGURE 5. TYPICAL JUNCTION CAPACITANCE H16 4.97bgppd300 DIOTEC ELECTRONICS CORP. Data Sheet No. GPPD-400-1B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 MECHANICAL SPECIFICATION FEATURES R PROPRIETARY SOFT GLASS JUNCTION PASSIVATION FOR SUPERIOR RELIABILITY AND PERFORMANCE ACTUAL SIZE OF DO-27 PACKAGE SERIES GP400 - GP410 DO - 27 VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM MECHANICAL STRENGTH AND HEAT DISSIPATION (Solder Voids: Typical < 2%, Max. < 10% of Die Area) LL BD (Dia) EXTREMELY LOW LEAKAGE AT HIGH TEMPERATURES LOW FORWARD VOLTAGE DROP BL Color Band Denotes Cathode 4A at TA = 75 oC WITH NO THERMAL RUNAWAY MECHANICAL DATA LL Case: JEDEC DO-27 molded silica glass (U/L Flammability Rating 94V-0) Terminals: Plated axial leads LD (Dia) Soldering: Per MIL-STD 202 Method 208 guaranteed Minimum In mm Sym Polarity: Color band denotes cathode Maximum In mm BL 0.365 9.28 Mounting Position: Any BD 0.205 5.2 Weight: 0.02 Ounces (0.7 Grams) LL LD 0.052 1.3 1.00 0.048 25.4 1.2 MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%. PARAMETER (TEST CONDITIONS) RATINGS SYMBOL GP400 GP401 GP402 GP404 GP406 GP408 GP410 Series Number Maximum DC Blocking Voltage VRM 50 Maximum RMS Voltage VRMS Maximum Peak Recurrent Reverse Voltage VRRM Average Forward Rectified Current @ TA = 75 oC, Lead length = 0.375 in. (9.5 mm) Peak Forward Surge Current (8.3 mSec single half sine wave superimposed on rated load) Maximum Forward Voltage at 4 Amps DC Maximum Full Cycle Reverse Current @ TL = 75 oC (Note 1) Maximum Average DC Reverse Current At Rated DC Blocking Voltage @ TA = 25oC o @ TA = 100 C Typical Thermal Resistance, Junction to Ambient (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range NOTES: (1) Lead length = 0.375 in. (9.5 mm) (2) Measured at 1MHz & applied reverse voltage of 4 volts UNITS 1000 100 200 400 600 800 35 70 140 280 420 560 700 50 100 200 400 600 800 1000 IO 4 IFSM 200 VFM 1 IRM(AV) 20 IRM 2 50 RθJA 18 VOLTS AMPS VOLTS µA °C/W CJ 70 pF TJ, TSTG -65 to +175 °C 4.97fgppd400 H17 DIOTEC ELECTRONICS CORP. Data Sheet No. GPPD-400-2B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 4 AMP HIGH RELIABILITY SOFT GLASS PASSIVATED SILICON DIODES RATING & CHARACTERISTIC CURVES FOR SERIES GP400 - GP410 RESISTIVE OR INDUCTIVE LOADS 1000 Maximum Non-repetitive 100 o TJ = 25 C NOTE 1 Maximum Repetitive 10 1 10 100 Number of Cycles at 60Hz o Ambient Temperature, C FIGURE 1. FORWARD CURRENT DERATING CURVE FIGURE 2. FORWARD SURGE CURRENT 100 10 10 1.0 1.0 0.1 o TJ = 25 C 0.1 .01 20 60 80 100 120 140 Percent of Rated Peak Reverse Voltage 0.01 FIGURE 4. TYPICAL REVERSE CHARACTERISTICS Instantaneous Forward Voltage (Volts) FIGURE 3. TYPICAL FORWARD CHARACTERISTICS 100 TJ = 25 oC NOTES (1) Single Phase, Half Wave, 60 Hz; Lead Length = 0.375" (9.5mm) (2) TJ = 25 oC, Pulse Width = 300 µ Sec, 1.0% Duty Cycle 10 0.1 0.1 1 10 100 Reverse Voltage, (Volts) FIGURE 5. TYPICAL JUNCTION CAPACITANCE H18 4.97bgpdp400 DIOTEC ELECTRONICS CORP. Data Sheet No. GPDP-601-1C 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 MECHANICAL SPECIFICATION FEATURES ACTUAL SIZE OF GP600 PACKAGE Low cost SERIES GP600 - GP610 Low leakage LL Low forward voltage drop BD (Dia) High current capacity BL Color Band Denotes Cathode Easily cleaned with freon, alcohol, chlorothene and similar solvents MECHANICAL DATA LL Case: Molded epoxy (U/L Flammability Rating 94V-0) LD (Dia) Terminals: Plated axial leads Soldering: Per MIL-STD 202 Method 208 guaranteed Minimum In mm Sym Polarity: Color band denotes cathode Maximum In mm 8.6 0.360 9.1 0.340 8.6 0.360 9.1 1.00 0.048 25.4 1.2 0.052 1.3 BL 0.340 Mounting Position: Any BD Weight: 0.07 Ounces (2.1 Grams) LL LD MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%. PARAMETER (TEST CONDITIONS) RATINGS SYMBOL Series Number GP600 GP601 GP602 GP604 GP606 GP608 GP610 Maximum DC Blocking Voltage VRM 50 Maximum RMS Voltage VRMS Maximum Peak Recurrent Reverse Voltage VRRM Average Forward Rectified Current @ TA = 60 oC, Lead length = 0.375 in. (9.5 mm) Peak Forward Surge Current (8.3 mSec single half sine wave superimposed on rated load) Maximum Forward Voltage at 6 Amps DC Maximum Full Cycle Reverse Current @ TL = 75 oC (Note 1) Maximum Average DC Reverse Current At Rated DC Blocking Voltage @ TA = 25oC o @ TA = 100 C Typical Thermal Resistance, Junction to Ambient (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range NOTES: (1) Lead length = 0.375 in. (9.5 mm) (2) Measured at 1MHz & applied reverse voltage of 4 volts UNITS 1000 100 200 400 600 800 35 70 140 280 420 560 700 50 100 200 400 600 800 1000 IO 6 IFSM 400 VFM 1 IRM(AV) 25 IRM 10 100 RθJA 10 VOLTS AMPS VOLTS µA °C/W CJ 100 pF TJ, TSTG -65 to +175 °C 01.00 fgpdp601 H19 DIOTEC ELECTRONICS CORP. Data Sheet No. GPDP-601-2B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 6 AMP GENERAL PURPOSE SILICON DIODES RATING & CHARACTERISTIC CURVES FOR SERIES GP600 - GP610 500 RESISTIVE OR INDUCTIVE LOADS 400 300 Standard PC Board Mounting (Recommended Method) 200 Ground Plane PC Board With 1" x 1" Copper Surface Area TJ = 25 oC 100 NOTE 1 0 Ambient Temperature, o C 10 1 FIGURE 1. FORWARD CURRENT DERATING CURVE 100 Number of Cycles at 60 Hz FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT 1000 100 100 10 TJ = 100 oC 10 1.0 0.1 1.0 TJ = 25 oC 0.01 20 60 80 100 120 140 0.1 Percent of Rated Peak Reverse Voltage Instantaneous Forward Voltage (Volts) FIGURE 3. TYPICAL FORWARD CHARACTERISTICS FIGURE 4. TYPICAL REVERSE CHARACTERISTICS 20 15 NOTES (1) Single Phase, Half Wave, 60 Hz 10 (2) TJ = 25 oC, Pulse Width = 300 µSec, 1.0% Duty Cycle L L 5 Both Leads of Equal Length, L 0 0 0.5 1.0 Lead Length toHeat Sink, L (Inches) FIGURE 5. TYPICAL THERMAL RESISTANCE H20 4.97bgpdp601 DIOTEC ELECTRONICS CORP. Data Sheet No. UFSD-101-1B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 MECHANICAL SPECIFICATION FEATURES 1N4148 ACTUAL SIZE OF DO-35 PACKAGE Hermetically sealed glass package DO-35 Low cost Super fast recovery time LL BD (Dia) Low leakage Low forward voltage drop BL Color Band Denotes Cathode High current capability MECHANICAL DATA LL Case: JEDEC DO-35 molded glass (U/L Flammability Rating 94V-0) Terminals: Plated axial leads LD (Dia) Soldering: Per MIL-STD 202 Method 208 guaranteed Minimum In mm Sym Polarity: Color band denotes cathode Maximum In mm 3.6 0.150 3.81 0.07 1.78 0.072 1.83 1.00 0.02 25.4 0.52 0.03 0.8 BL 0.142 Mounting Position: Any BD Weight: 0.005 Ounces (0.14 Grams) LL LD MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%. PARAMETER (TEST CONDITIONS) SYMBOL Series Number UNITS 1N4148 Breakdown Voltage at IR = 5 µA Breakdown Voltage at IR = 100 µA Maximum Peak Recurrent Reverse Voltage Average Forward Rectified Current @ TA = 50 oC, Lead length = 0.375 in. (9.5 mm) Pulse Width = 1 Sec Peak Forward Surge Current Pulse Width = 1 µSec Maximum Forward Voltage at 10 mA DC Maximum Power Dissipation Maximum Average DC Reverse Current RATINGS @ VR = 20V, TA = 25oC @ VR = 75V, TA = 150oC Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range NOTES: (1) Measured at IR = 10 mA, VR = 6V, RL = 100Ω; recover to 1 mA (2) Measured at 1MHz & applied reverse voltage of 0 volts DC VB 75 VB 100 VRRM 75 IO 150 mA IFSM 1 4 AMPS VFM 1 VOLTS PFM 500 mW IRM 25 5 nA µA TRR 4 nS CJ 4 pF TJ, TSTG -65 to +175 VOLTS °C 4.97fufsd101 H21 DIOTEC ELECTRONICS CORP. Data Sheet No. UFSD-100-2B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 1N4148 MINIATURE ULTRA FAST SWITCHING DIODE RATING & CHARACTERISTIC CURVES FOR THE 1N4148 Reverse Voltage, Volts FIGURE 2. TYPICAL JUNCTION CAPACITANCE Case Temperature, oC FIGURE 1. FORWARD CURRENT DERATING CURVE 100 1.0 10 0.1 TJ = 25 oC 1.0 o (1) TA = 175 C (2) TA = 125 oC (3) TA = 75 oC 1 3 5 0.1 0.01 (4) TA = 50 oC (5) TA = 25 oC .001 2 4 0 20 40 60 80 100 120 140 Percent of Rated Peak Reverse Voltage FIGURE 4. TYPICAL REVERSE CHARACTERISTICS 0.01 Instantaneous Forward Voltage (Volts) FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE H22 4.97bufsd100 DIOTEC ELECTRONICS CORP. Data Sheet No. FSDP-101-1B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 MECHANICAL SPECIFICATION FEATURES ACTUAL SIZE OF DO-41 PACKAGE Low cost SERIES 1N4933 - 1N4937 DO - 41 Low leakage LL Low forward voltage drop BD (Dia) High current capacity BL Fast switching for high efficiency Color Band Denotes Cathode MECHANICAL DATA LL Case: JEDEC DO-41, molded plastic (U/L Flammability Rating 94V-0) Terminals: Plated axial leads LD (Dia) Soldering: Per MIL-STD 202 Method 208 guaranteed Sym Polarity: Color band denotes cathode BL Mounting Position: Any BD Weight: 0.012 Ounces (0.34 Grams) LL LD Minimum In mm Maximum In mm 4.1 0.205 5.2 0.103 2.6 0.107 2.7 1.00 0.028 25.4 0.71 0.034 0.86 0.160 MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%. PARAMETER (TEST CONDITIONS) RATINGS SYMBOL Series Number UNITS 1N4933 1N4934 1N4935 1N4936 1N4937 100 200 400 600 Maximum DC Blocking Voltage VRM 50 Maximum RMS Voltage VRMS 35 70 140 280 420 Maximum Peak Recurrent Reverse Voltage VRRM 50 100 200 400 600 Average Forward Rectified Current @ TA = 75 oC, Lead length = 0.375 in. (9.5 mm) Peak Forward Surge Current ( 8.3 mSec single half sine wave superimposed on rated load) Maximum Forward Voltage at 1 Amp DC Maximum Reverse Recovery Time (IF=1A, VR=30V - See Fig. 5) Maximum Average DC Reverse Current At Rated DC Blocking Voltage @ TA = 25oC o @ TA = 100 C Typical Thermal Resistance, Junction to Ambient (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range VOLTS IO 1 IFSM 30 VFM 1.2 VOLTS TRR 200 nS IRM 5 100 µA RθJA 41 °C/W AMPS CJ 15 pF TJ, TSTG -65 to +175 °C NOTES: (1) Thermal resistance from junction to ambient with diode mounted on PC Board and lead lengths = 0.375 in. (9.5 mm) (2) Measured at 1MHz & applied reverse voltage of 4 volts 4.97ffsdp1 H23 DIOTEC ELECTRONICS CORP. Data Sheet No. FSDP-101-2B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 1 AMP FAST RECOVERY SILICON DIODES RATING & CHARACTERISTIC CURVES FOR SERIES 1N4933 - 1N4937 50 40 JEDEC Method 8.3 mS Half Sine Wave TJ = 150 oC 30 Single Phase, Half wave, 60 Hz Resistive and Inductive Loads 20 10 0 Ambient Temperature, oC 10 1 100 Number of Cycles at 60 Hz FIGURE 1. FORWARD CURRENT DERATING CURVE FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT 100 10 T J = 25 oC 1.0 f = 1 MHz 10 0.1 TJ = 25 oC Pulse Width = 300 µS 0.1 0.1 0.01 Instantaneous Forward Voltage (Volts) FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE 50 Ω noninductive 1 10 Reverse Voltage, (Volts) FIGURE 4. TYPICAL JUNCTION CAPACITANCE PER DIODE 10 Ω noninductive TRR 0.5 D.U.T. (+) (-) 25 VDC (APPROX) 0.0 PULSE GENERATOR (Note 2) (-) 1Ω noninductive (+) -0.5 OSCILLOSCOPE (Note 1) -1.0 NOTES: (1) Rise time = 7nS max., input impedance = 1 Megohm, 22 pF (2) Rise time = 10nS max., source impedance = 50 ohms H24 Set time base for 10nS/cm 1 cm FIGURE 5. REVERSE RECOVERY TEST SETUP AND TIME CHARACTERISTIC 4.97bfsdp101 DIOTEC ELECTRONICS CORP. Data Sheet No. FSDP-103-1B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 MECHANICAL SPECIFICATION FEATURES ACTUAL SIZE OF DO-41 PACKAGE Low cost SERIES RP100 - RP110 DO - 41 Low leakage LL Low forward voltage drop BD (Dia) High current capacity BL Fast switching for high efficiency Color Band Denotes Cathode MECHANICAL DATA LL Case: JEDEC DO-41, molded plastic (U/L Flammability Rating 94V-0) Terminals: Plated axial leads LD (Dia) Soldering: Per MIL-STD 202 Method 208 guaranteed Minimum In mm Sym Polarity: Color band denotes cathode BL Mounting Position: Any BD Weight: 0.012 Ounces (0.34 Grams) LL LD Maximum In mm 4.1 0.205 5.2 0.103 2.6 0.107 2.7 1.00 0.028 25.4 0.71 0.034 0.86 0.160 MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%. PARAMETER (TEST CONDITIONS) RATINGS SYMBOL Series Number RP100 RP101 RP102 RP104 RP106 RP108 RP110 Maximum DC Blocking Voltage VRM 50 Maximum RMS Voltage VRMS Maximum Peak Recurrent Reverse Voltage VRRM Average Forward Rectified Current @ TA = 75 oC (Lead length = 0.375 in. (9.5 mm)) Peak Forward Surge Current ( 8.3 mSec single half sine wave superimposed on rated load) Maximum Forward Voltage at 1 Amp DC Maximum Reverse Recovery Time (IF=0.5A, IR=1A, IRR=0.25A) Maximum Average DC Reverse Current At Rated DC Blocking Voltage @ TA = 25oC o @ TA = 100 C Typical Thermal Resistance, Junction to Ambient (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range UNITS 1000 100 200 400 600 800 35 70 140 280 420 560 700 50 100 200 400 600 800 1000 IO 1 IFSM 30 VFM 1.3 VOLTS AMPS TRR 150 VOLTS 250 500 ( Note 3) nS IRM 5 50 µA RθJA 50 °C/W CJ 15 pF TJ, TSTG -65 to +175 °C NOTES: (1) Thermal resistance junction to ambient with diode mounted on PC Board and lead lengths = 0.375 in. (9.5 mm) (2) Measured at 1MHz & applied reverse voltage of 4 volts (3) 300nS available - consult factory 4.97ffsdp1a H25 DIOTEC ELECTRONICS CORP. Data Sheet No. FSDP-103-2B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 1 AMP FAST RECOVERY SILICON DIODES RATING & CHARACTERISTIC CURVES FOR SERIES RP100 - RP110 50 40 JEDEC Method 8.3 mS Half Sine Wave TJ = 150 oC 30 Single Phase, Half wave, 60 Hz Resistive and Inductive Loads 20 10 0 Ambient Temperature, oC 10 1 FIGURE 1. FORWARD CURRENT DERATING CURVE 100 Number of Cycles at 60 Hz FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT 100 10 T J = 25 oC 1.0 f = 1 MHz 10 0.1 TJ = 25 oC Pulse Width = 300 µS 1% Duty Cycle 0.1 0.1 0.01 Instantaneous Forward Voltage (Volts) FIGURE 3. TYPICAL FORWARD CHARACTERISTIC 50 Ω noninductive 1 10 Reverse Voltage, (Volts) FIGURE 4. TYPICAL JUNCTION CAPACITANCE 10 Ω noninductive TRR 0.5 D.U.T. (+) (-) 25 VDC (APPROX) 0.0 PULSE GENERATOR (Note 2) (-) 1Ω noninductive (+) -0.5 OSCILLOSCOPE (Note 1) -1.0 NOTES: (1) Rise time = 7nS max., input impedance = 1 Megohm, 22 pF (2) Rise time = 10nS max., source impedance = 50 ohms Set time base for 10nS/cm 1 cm FIGURE 5. REVERSE RECOVERY TEST SETUP AND TIME CHARACTERISTIC H26 4.97bfsdp103 DIOTEC ELECTRONICS CORP. Data Sheet No. FSPD-100-1B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 MECHANICAL SPECIFICATION FEATURES R PROPRIETARY SOFT GLASS JUNCTION PASSIVATION FOR SUPERIOR RELIABILITY AND PERFORMANCE ACTUAL SIZE OF DO-41 PACKAGE SERIES RGP100 - RGP110 DO - 41 VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM MECHANICAL STRENGTH AND HEAT DISSIPATION (Solder Voids: Typical < 2%, Max. < 10% of Die Area) LL BD (Dia) EXTREMELY LOW LEAKAGE AT HIGH TEMPERATURES LOW FORWARD VOLTAGE DROP BL Color Band Denotes Cathode 1A at TA = 75 oC WITH NO THERMAL RUNAWAY MECHANICAL DATA LL Case: JEDEC DO-41, molded silica glass (U/L Flammability Rating 94V-0) Terminals: Plated axial leads LD (Dia) Soldering: Per MIL-STD 202E Method 208 guaranteed Minimum In mm Sym Polarity: Color band denotes cathode BD Weight: 0.012 Ounces (0.34 Grams) LL LD 4.1 0.205 5.2 0.103 2.6 0.107 2.7 1.00 0.028 25.4 0.71 0.034 0.86 0.160 BL Mounting Position: Any Maximum In mm MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%. PARAMETER (TEST CONDITIONS) RATINGS SYMBOL Series Number UNITS RGP 100 RGP 101 RGP 102 RGP 104 RGP 106 RGP 108 RGP 110 100 200 400 600 800 1000 Maximum DC Blocking Voltage VRM 50 Maximum RMS Voltage VRMS 35 70 140 280 420 560 700 Maximum Peak Recurrent Reverse Voltage VRRM 50 100 200 400 600 800 1000 Average Forward Rectified Current @ TA = 75 oC, Lead length = 0.375 in. (9.5 mm) Peak Forward Surge Current ( 8.3 mSec single half sine wave superimposed on rated load) Maximum Forward Voltage at 1 Amp DC Maximum Reverse Recovery Time (IF=0.5A, IR=1A, IRR=0.25A) Maximum Average DC Reverse Current At Rated DC Blocking Voltage @ TA = 25oC o @ TA = 100 C Typical Thermal Resistance, Junction to Ambient (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range NOTES: (1) Lead length = 0.375 in. (9.5 mm) (2) Measured at 1MHz & applied reverse voltage of 4 volts (3) 300nS avaiable - consult factory IO 1 IFSM 50 VFM 1.2 VOLTS AMPS TRR 150 VOLTS 250 500 (Note 3) nS IRM 0.5 25 µA RθJA 55 °C/W CJ 15 pF TJ, TSTG -65 to +175 °C 4.97ffspd100 H27 DIOTEC ELECTRONICS CORP. Data Sheet No. FSPD-100-2B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 1 AMP HIGH RELIABILITY FAST RECOVERY DIODES RATING & CHARACTERISTIC CURVES FOR SERIES RGP100 - RGP110 50 JEDEC Method 8.3 mS Half Sine Wave TJ = 175 oC 40 30 Single Phase, Half wave, 60 Hz Resistive and Inductive Loads Lead Length = 0.375" (9.5 mm) 20 10 Ambient Temperature, oC 0 10 1 FIGURE 1. FORWARD CURRENT DERATING CURVE 100 Number of Cycles at 60 Hz FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT 100 10 Pulse Width = 300 µS 1% Duty Cycle TJ =150 oC TJ = 25 oC f = 1 MHz VSIG = 50 mV P-P 1.0 10 0.1 TJ =25 oC 0.1 0.1 0.01 Instantaneous Forward Voltage (Volts) 10 FIGURE 4. TYPICAL JUNCTION CAPACITANCE FIGURE 3. TYPICAL FORWARD CHARACTERISTIC 50 Ω noninductive 1 Reverse Voltage, (Volts) 10 Ω noninductive TRR 0.5 D.U.T. (+) (-) 25 VDC (APPROX) 0.0 PULSE GENERATOR (Note 2) (-) 1Ω noninductive (+) -0.5 OSCILLOSCOPE (Note 1) -1.0 NOTES: (1) Rise time = 7nS max., input impedance = 1 Megohm, 22 pF (2) Rise time = 10nS max., source impedance = 50 ohms Set time base for 10nS/cm 1 cm FIGURE 5. REVERSE RECOVERY TEST SETUP AND TIME CHARACTERISTIC H28 4.97bfspd100 DIOTEC ELECTRONICS CORP. Data Sheet No. FSPD-200-1B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 MECHANICAL SPECIFICATION FEATURES R PROPRIETARY SOFT GLASS JUNCTION PASSIVATION FOR SUPERIOR RELIABILITY AND PERFORMANCE ACTUAL SIZE OF DO-41 PACKAGE SERIES RGP200 - RGP210 DO - 41 VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM MECHANICAL STRENGTH AND HEAT DISSIPATION (Solder Voids: Typical < 2%, Max. < 10% of Die Area) LL BD (Dia) EXTREMELY LOW LEAKAGE AT HIGH TEMPERATURES LOW FORWARD VOLTAGE DROP BL Color Band Denotes Cathode 2A at TA = 75 oC WITH NO THERMAL RUNAWAY MECHANICAL DATA LL Case: JEDEC DO-41 molded plastic (U/L Flammability Rating 94V-0) Terminals: Plated axial leads LD (Dia) Soldering: Per MIL-STD 202 Method 208 guaranteed Polarity: Color band denotes cathode Minimum In mm Sym 0.160 BL Mounting Position: Any Weight: 0.01 Ounces (0.4 Grams) Maximum In mm 4.1 0.205 5.2 BD 0.103 2.6 0.107 2.7 LL LD 1.00 0.028 25.4 0.71 0.034 0.86 MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%. PARAMETER (TEST CONDITIONS) RATINGS SYMBOL Series Number UNITS RGP 200 RGP 201 RGP 202 RGP 204 RGP 206 RGP 208 RGP 210 Maximum DC Blocking Voltage VRM 50 100 200 400 600 800 1000 Maximum RMS Voltage VRMS 35 70 140 280 420 560 700 Maximum Peak Recurrent Reverse Voltage VRRM 50 100 200 400 600 800 1000 Average Forward Rectified Current @ TA = 75 oC, Lead length = 0.375 in. (9.5 mm) Peak Forward Surge Current ( 8.3 mSec single half sine wave superimposed on rated load) IO 2 IFSM 60 AMPS Maximum Forward Voltage at 2 Amps DC VFM Maximum Reverse Recovery Time (IF=0.5A, IR=1A, IRR=0.25A) TRR Maximum Average DC Reverse Current At Rated DC Blocking Voltage Typical Junction Capacitance (Note 1) Operating and Storage Temperature Range NOTES: (1) Measured at 1MHz & applied reverse voltage of 4 volts (2) 300 nS available - consult factory @ TA = 25oC @ TA = 100oC VOLTS IRM VOLTS 1.3 150 250 1.0 100 500 (Note 2) nS µA CJ 15 pF TJ, TSTG -65 to +175 °C 4.97ffspd200 H29 DIOTEC ELECTRONICS CORP. Data Sheet No. FSPD-200-2B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 2 AMP FAST RECOVERY SILICON DIODES RATING & CHARACTERISTIC CURVES FOR SERIES RGP200 - RGP210 50 40 30 Single Phase, Half wave, 60 Hz Resistive and Inductive Loads Lead Length = 0.375" (9.5 mm) 20 JEDEC Method 8.3 mS Single Half Sine Wave 10 0 Ambient Temperature, oC 10 1 FIGURE 1. FORWARD CURRENT DERATING CURVE 100 Number of Cycles at 60 Hz FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT 20 100 10 TJ = 25 oC f = 1 MHz VSIG = 50 mV P-P 1.0 10 0.1 TJ = 25 oC Pulse Width = 300 µS 1% Duty Cycle 0.1 0.1 0.01 Instantaneous Forward Voltage (Volts) FIGURE 3. TYPICAL FORWARD CHARACTERISTIC 50 Ω noninductive 1 10 Reverse Voltage, (Volts) FIGURE 4. TYPICAL JUNCTION CAPACITANCE 10 Ω noninductive TRR 0.5 D.U.T. (+) (-) 25 VDC (APPROX) 0.0 PULSE GENERATOR (Note 2) (-) 1Ω noninductive (+) -0.5 OSCILLOSCOPE (Note 1) -1.0 NOTES: (1) Rise time = 7nS max., input impedance = 1 Megohm, 22 pF (2) Rise time = 10nS max., source impedance = 50 ohms Set time base for 10nS/cm 1 cm FIGURE 5. REVERSE RECOVERY TEST SETUP AND TIME CHARACTERISTIC H30 4.97bfspd200 DIOTEC ELECTRONICS CORP. Data Sheet No. FSDP-301-1B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 MECHANICAL SPECIFICATION FEATURES ACTUAL SIZE OF DO-27 PACKAGE Low cost SERIES RP300 - RP310 DO - 27 Low leakage LL Low forward voltage drop BD (Dia) High current capacity BL Fast switching for high efficiency Color Band Denotes Cathode MECHANICAL DATA LL Case: JEDEC DO-27 molded plastic (U/L Flammability Rating 94V-0) Terminals: Plated axial leads LD (Dia) Soldering: Per MIL-STD 202 Method 208 guaranteed Sym Polarity: Color band denotes cathode Mounting Position: Any Maximum In mm BL 0.365 9.28 BD 0.205 5.2 0.052 1.3 LL LD Weight: 0.02 Ounces (0.7 Grams) Minimum In mm 1.00 0.048 25.4 1.2 MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%. PARAMETER (TEST CONDITIONS) RATINGS SYMBOL Series Number UNITS RP300 RP301 RP302 RP304 RP306 RP308 RP310 Maximum DC Blocking Voltage VRM 50 100 200 400 600 800 1000 Maximum RMS Voltage VRMS 35 70 140 280 420 560 700 Maximum Peak Recurrent Reverse Voltage VRRM 50 100 200 400 600 800 1000 Average Forward Rectified Current @ TA = 55 oC, Lead length = 0.375 in. (9.5 mm) Peak Forward Surge Current ( 8.3 mSec single half sine wave superimposed on rated load) IO 3 IFSM 200 AMPS Maximum Forward Voltage at 3 Amps DC VFM Maximum Reverse Recovery Time (IF=0.5A, IR=1A, IRR=0.25A) TRR Maximum Average DC Reverse Current At Rated DC Blocking Voltage Typical Junction Capacitance (Note 1) Operating and Storage Temperature Range at =1MHz applied reverse voltage of 4 volts NOTES: (1) Measured Lead length 0.375&in. (9.5 mm) (2) 300 nS avaiable - consult withreverse factoryvoltage of 4 volts Measured at 1MHz & applied @ TA = 25oC @ TA = 100oC VOLTS IRM VOLTS 1.3 150 250 10 150 500 (Note 2) nS µA CJ 60 pF TJ, TSTG -65 to +175 °C 4.97ffsdp301 H31 DIOTEC ELECTRONICS CORP. Data Sheet No. FSDP-301-2B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 3 AMP FAST RECOVERY SILICON DIODES RATING & CHARACTERISTIC CURVES FOR SERIES RP300 - RP310 500 JEDEC Method 8.3 mS Single Half Sine Wave TJ = 55 oC 100 Single Phase, Half wave, 60 Hz Resistive and Inductive Loads Lead Length = 0.375" (9.5 mm) Ambient Temperature, oC 10 10 1 FIGURE 1. FORWARD CURRENT DERATING CURVE 100 Number of Cycles at 60 Hz FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT 100 10 TJ = 25 oC 1.0 f = 1 MHz 10 0.1 TJ = 25 oC Pulse Width = 300 µS 1% Duty Cycle 0.1 0.1 0.01 Instantaneous Forward Voltage (Volts) 10 FIGURE 4. TYPICAL JUNCTION CAPACITANCE FIGURE 3. TYPICAL FORWARD CHARACTERISTIC 50 Ω noninductive 1 Reverse Voltage, (Volts) 10 Ω noninductive TRR 0.5 D.U.T. (+) (-) 25 VDC (APPROX) 0.0 PULSE GENERATOR (Note 2) (-) 1Ω noninductive (+) -0.5 OSCILLOSCOPE (Note 1) -1.0 NOTES: (1) Rise time = 7nS max., input impedance = 1 Megohm, 22 pF (2) Rise time = 10nS max., source impedance = 50 ohms Set time base for 10nS/cm 1 cm FIGURE 5. REVERSE RECOVERY TEST SETUP AND TIME CHARACTERISTIC H32 4.97bfsdp301 DIOTEC ELECTRONICS CORP. Data Sheet No. FSPD-300-1B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 MECHANICAL SPECIFICATION FEATURES R PROPRIETARY SOFT GLASS JUNCTION PASSIVATION FOR SUPERIOR RELIABILITY AND PERFORMANCE ACTUAL SIZE OF DO-27 PACKAGE SERIES RGP300 - RGP310 DO - 27 VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM MECHANICAL STRENGTH AND HEAT DISSIPATION (Solder Voids: Typical < 2%, Max. < 10% of Die Area) LL BD (Dia) EXTREMELY LOW LEAKAGE AT HIGH TEMPERATURES LOW FORWARD VOLTAGE DROP BL Color Band Denotes Cathode 3A at TA = 55 oC WITH NO THERMAL RUNAWAY MECHANICAL DATA LL Case: JEDEC DO-27 molded silica glass (U/L Flammability Rating 94V-0) Terminals: Plated axial leads LD (Dia) Soldering: Per MIL-STD 202 Method 208 guaranteed Minimum In mm Sym Polarity: Color band denotes cathode Mounting Position: Any BL 0.365 9.28 BD 0.205 5.2 0.052 1.3 1.00 0.048 LL LD Weight: 0.02 Ounces (0.7 Grams) Maximum In mm 25.4 1.2 MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%. PARAMETER (TEST CONDITIONS) RATINGS SYMBOL Series Number UNITS RGP 300 RGP 301 RGP 302 RGP 304 RGP 306 RGP 308 RGP 310 Maximum DC Blocking Voltage VRM 50 100 200 400 600 800 1000 Maximum RMS Voltage VRMS 35 70 140 280 420 560 700 Maximum Peak Recurrent Reverse Voltage VRRM 50 100 200 400 600 800 1000 Average Forward Rectified Current @ TA = 55 oC, Lead length = 0.375 in. (9.5 mm) Peak Forward Surge Current ( 8.3 mSec single half sine wave superimposed on rated load) IO 3 IFSM 200 AMPS Maximum Forward Voltage at 3 Amps DC VFM Maximum Reverse Recovery Time (IF=0.5A, IR=1A, IRR=0.25A) TRR Maximum Average DC Reverse Current At Rated DC Blocking Voltage Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range NOTES: (1) Lead length = 0.375 in. (9.5 mm) (2) Measured at 1MHz & applied reverse voltage of 4 volts (3) 300 nS avaiable - consult with factory @ TA = 25oC @ TA = 100oC VOLTS IRM VOLTS 1.2 150 250 2 100 500 (Note 3) nS µA CJ 40 pF TJ, TSTG -65 to +175 °C 4.97ffspd300 H33 DIOTEC ELECTRONICS CORP. Data Sheet No. FSPD-300--2B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 3 AMP HIGH RELIABILITY FAST RECOVERY DIODES RATING & CHARACTERISTIC CURVES FOR SERIES RGP300 - RGP310 500 JEDEC Method 8.3 mS Single Half Sine Wave TJ = 55 oC 100 Single Phase, Half wave, 60 Hz Resistive and Inductive Loads Lead Length = 0.375" (9.5 mm) Ambient Temperature, oC 10 10 1 FIGURE 1. FORWARD CURRENT DERATING CURVE 100 Number of Cycles at 60 Hz FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT 100 10 TJ = 25 oC 1.0 10 0.1 TJ = 25 oC Pulse Width = 300 µS 1% Duty Cycle 0.1 0.1 0.01 Instantaneous Forward Voltage (Volts) 10 FIGURE 4. TYPICAL JUNCTION CAPACITANCE FIGURE 3. TYPICAL FORWARD CHARACTERISTIC 50 Ω noninductive 1 Reverse Voltage, (Volts) 10 Ω noninductive TRR 0.5 D.U.T. (+) (-) 25 VDC (APPROX) 0.0 PULSE GENERATOR (Note 2) (-) 1Ω noninductive (+) -0.5 OSCILLOSCOPE (Note 1) -1.0 NOTES: (1) Rise time = 7nS max., input impedance = 1 Megohm, 22 pF (2) Rise time = 10nS max., source impedance = 50 ohms Set time base for 10nS/cm 1 cm FIGURE 5. REVERSE RECOVERY TEST SETUP AND TIME CHARACTERISTIC H34 4.97bfspd300 DIOTEC ELECTRONICS CORP. Data Sheet No. FSDP-601-1C 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 MECHANICAL SPECIFICATION FEATURES ACTUAL SIZE OF RP600 PACKAGE Low cost SERIES RP600 - RP610 Low leakage LL Low forward voltage drop BD (Dia) High current capacity BL Color Band Denotes Cathode Fast switching for high efficiency MECHANICAL DATA LL Case: Molded epoxy (U/L Flammability Rating 94V-0) LD (Dia) Terminals: Plated axial leads Soldering: Per MIL-STD 202 Method 208 guaranteed Minimum In mm Sym Polarity: Color band denotes cathode BL 0.340 Maximum In mm 8.6 0.360 9.1 Mounting Position: Any BD 0.340 8.6 0.360 9.1 Weight: 0.07 Ounces (2.1 Grams) LL LD 1.00 0.048 25.4 1.2 0.052 1.3 MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%. PARAMETER (TEST CONDITIONS) RATINGS SYMBOL Series Number UNITS RP600 RP601 RP602 RP604 RP606 RP608 RP610 Maximum DC Blocking Voltage VRM 50 100 200 400 600 800 1000 Maximum RMS Voltage VRMS 35 70 140 280 420 560 700 Maximum Peak Recurrent Reverse Voltage VRRM 50 100 200 400 600 800 1000 Average Forward Rectified Current @ TA = 60 oC, Lead length = 0.375 in. (9.5 mm) Peak Forward Surge Current ( 8.3 mSec single half sine wave superimposed on rated load) IO 6 IFSM 300 AMPS Maximum Forward Voltage at 6 Amps DC VFM Maximum Reverse Recovery Time (IF=0.5A, IR=1A, IRR=0.25A) TRR Maximum Average DC Reverse Current At Rated DC Blocking Voltage Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range NOTES: (1) Lead length = 0.375 in. (9.5 mm) (2) Measured at 1MHz & applied reverse voltage of 4 volts (3) 300 nS avaiable - consult with factory @ TA = 25oC @ TA = 100oC VOLTS IRM VOLTS 1.3 150 250 10 200 500 (Note 3) nS µA CJ 100 pF TJ, TSTG -65 to +175 °C 01.00ffsdp601 H35 DIOTEC ELECTRONICS CORP. Data Sheet No. FSDP-601-2B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 6 AMP FAST RECOVERY DIODES RATING & CHARACTERISTIC CURVES FOR SERIES RP600 - RP610 500 400 JEDEC Method 8.3 mS Single Half Sine Wave 300 Single Phase, Half wave, 60 Hz Resistive and Inductive Loads Lead Length = 0.375" (9.5 mm) TJ = 25 oC 200 100 TJ = 150 oC Ambient Temperature, oC 0 10 1 FIGURE 1. FORWARD CURRENT DERATING CURVE 100 Number of Cycles at 60 Hz FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT 1000 1000 100 TJ = 25 oC f = 1 MHz 10 100 1.0 10 0.1 1 0.1 Instantaneous Forward Voltage (Volts) FIGURE 3. TYPICAL FORWARD CHARACTERISTICS 50 Ω noninductive 10 Reverse Voltage, (Volts) FIGURE 4. TYPICAL JUNCTION CAPACITANCE 10 Ω noninductive TRR 0.5 D.U.T. (+) (-) 25 VDC (APPROX) 0.0 PULSE GENERATOR (Note 2) (-) 1Ω noninductive (+) -0.5 OSCILLOSCOPE (Note 1) -1.0 NOTES: (1) Rise time = 7nS max., input impedance = 1 Megohm, 22 pF (2) Rise time = 10nS max., source impedance = 50 ohms Set time base for 10nS/cm 1 cm FIGURE 5. REVERSE RECOVERY TEST SETUP AND TIME CHARACTERISTIC H36 4.97bfsdp601 DIOTEC ELECTRONICS CORP. Data Sheet No. FSDG-800-1B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 MECHANICAL SPECIFICATION FEATURES Glass Passivated for high reliability/temperature performance ACTUAL SIZE OF TO-220AC PACKAGE SERIES RGP800 - RGP806 Low switching noise φP C Low forward voltage drop A A1 D4 Low thermal resistance D1 High surge current capability D Fast switching for high efficiency 2 B4 Low leakage B3 3 MECHANICAL DATA Case: TO-220 molded plastic (U/L Flammability Rating 94V-0) Terminals: Plated rectangular pins Solderability: Per MIL-STD 202 Method 208 guaranteed Polarity: Marked on case Mounting Position: Any Weight: 0.07 Ounces (2.05 Grams) A A1 A2 B B1 B2 B3 B4 C D D1 D2 D3 D4 D3 1 Minimum mm in Sym D2 Maximum in mm 0.187 4.75 B1 0.121* 0.14* 0.035 0.09 0.025* 0.050* 4.75* 3.56* 0.043 1.1 0.9 0.102 2.6 2.3 0.64* 1.27* 0.04 1.0 0.413 10.5 0.61 15.5 0.59 15.0 0.262* 6.6* 0.16 4.0 0.54 13.7 0.60 15.2 0.108* 2.75* φP 0.126* 3.2* * These dimensions are "Typicals". B2 B B1 A2 TO - 220AC MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%. PARAMETER (TEST CONDITIONS) RATINGS SYMBOL UNITS RGP800 RGP801 RGP802 RGP804 Series Number RGP806 Maximum DC Blocking Voltage VRM 50 100 200 400 600 Maximum RMS Voltage VRMS 35 70 140 280 420 VRRM 50 100 200 400 600 Maximum Peak Recurrent Reverse Voltage o Average Forward Rectified Current @ Tc = 110 C Peak Forward Surge Current ( 8.3mS single half sine wave superimposed on rated load) Maximum Forward Voltage at 8 Amps DC Maximum Average DC Reverse Current At Rated DC Blocking Voltage Typical Thermal Resistance, Junction to Case @ TC = 25 oC @ TC = 100 oC Typical Junction Capacitance (Note 1) Maximum Reverse Recovery Time (IF=0.5A, IR=1A, IRR=0.25A) Junction Operating and Storage Temperature Range NOTES: (1) Measured at 1MHz and an applied reverse voltage of 4 volts. VOLTS IO 8 IFSM 150 VFM 1.3 VOLTS µA RθJC 10 250 3 °C/W CJ 55 pF IRM TRR TJ, TSTG 150 AMPS 200 -50 to +150 250 nSec °C 4.97ffsdg800 H37 DIOTEC ELECTRONICS CORP. Data Sheet No. FSDG-800-2B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 8 AMP FAST RECOVERY DIODES RATING & CHARACTERISTIC CURVES FOR SERIES RGP800 - RGP806 500 Resistive and Inductive Loads 400 Case 300 200 Ambient NOTE 1 100 Temperature, oC 0 10 1 FIGURE 1. FORWARD CURRENT DERATING CURVE 100 Number of Cycles at 60 Hz FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT 100 100 10 TC = 100 oC 10 1.0 TC = 75 oC 1.0 0.1 TC = 25 oC 0.01 0.1 0 Instantaneous Forward Voltage (Volts) 20 40 60 80 100 120 140 Percent of Rated Peak Reverse Voltage FIGURE 3. TYPICAL FORWARD CHARACTERISTICS FIGURE 4. TYPICAL REVERSE CHARACTERISTICS 120 100 NOTES 80 (1) JEDEC Method, 8.3 mSec. Single Half Sine Wave, TJ = 150 oC 60 (2) TJ = 25 oC, Pulse Width = 300 µSec, 2.0% Duty Cycle 40 (3) TJ = 25 oC, f = 1 MHz 20 0.1 1 10 100 Reverse Voltage, (Volts) FIGURE 5. TYPICAL JUNCTION CAPACITANCE H38 4.97bfsdg800 DIOTEC ELECTRONICS CORP. Data Sheet No. FSDP-103-2B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 1 AMP FAST RECOVERY SILICON DIODES RATING & CHARACTERISTIC CURVES FOR SERIES RP100 - RP110 50 40 JEDEC Method 8.3 mS Half Sine Wave TJ = 150 oC 30 Single Phase, Half wave, 60 Hz Resistive and Inductive Loads 20 10 0 Ambient Temperature, oC 10 1 FIGURE 1. FORWARD CURRENT DERATING CURVE 100 Number of Cycles at 60 Hz FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT 100 10 T J = 25 oC 1.0 f = 1 MHz 10 0.1 TJ = 25 oC Pulse Width = 300 µS 1% Duty Cycle 0.1 0.1 0.01 Instantaneous Forward Voltage (Volts) FIGURE 3. TYPICAL FORWARD CHARACTERISTIC 50 Ω noninductive 1 10 Reverse Voltage, (Volts) FIGURE 4. TYPICAL JUNCTION CAPACITANCE 10 Ω noninductive TRR 0.5 D.U.T. (+) (-) 25 VDC (APPROX) 0.0 PULSE GENERATOR (Note 2) (-) 1Ω noninductive (+) -0.5 OSCILLOSCOPE (Note 1) -1.0 NOTES: (1) Rise time = 7nS max., input impedance = 1 Megohm, 22 pF (2) Rise time = 10nS max., source impedance = 50 ohms Set time base for 10nS/cm 1 cm FIGURE 5. REVERSE RECOVERY TEST SETUP AND TIME CHARACTERISTIC H26 4.97bfsdp103 SECTION I HIGH VOLTAGE DIODES STANDARD AND FAST RECOVERY DO-41 PACKAGE 200 to 500 MILLIAMPERES 1200 to 5000 VOLTS DO - 41 DIOTEC ELECTRONICS CORP. - 18020 Hobart Blvd., Unit B - Gardena, CA 90248 U.S.A. - PH: 310-767-1052 - FX: 310-767-7958 DIOTEC ELECTRONICS CORP. Data Sheet No. HVGP-1000-1C 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 MECHANICAL SPECIFICATION FEATURES ACTUAL SIZE OF DO-41 PACKAGE R PROPRIETARY SOFT GLASS JUNCTION PASSIVATION FOR SUPERIOR RELIABILITY AND PERFORMANCE SERIES GP1120 - GP1500 VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM MECHANICAL STRENGTH AND HEAT DISSIPATION (Solder Voids: Typical < 2%, Max. < 10% of Die Area) LL BD (Dia) EXTREMELY LOW LEAKAGE AT HIGH TEMPERATURES LOW FORWARD VOLTAGE DROP BL Color Band Denotes Cathode HIGH CURRENT CAPABILITY MECHANICAL DATA LL DO-41 Case: JEDEC DO-41 molded plastic (U/L Flammability Rating 94V-0) LD (Dia) Terminals: Plated axial leads Soldering: Per MIL-STD 202 Method 208 guaranteed Polarity: Color band denotes cathode Minimum In mm 0.160 4.1 Maximum In mm 5.2 0.205 BD 0.103 2.6 0.107 2.7 LL LD 1.00 0.028 25.4 0.71 0.034 0.86 Sym Mounting Position: Any BL Weight: DO-41 - 0.012 Ounces (0.34 Grams) MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%. PARAMETER (TEST CONDITIONS) RATINGS SYMBOL Series Number UNITS GP 1150 GP 1180 GP 1200 GP 1250 GP 1300 GP 1400 GP 1500 GP 1600 Maximum DC Blocking Voltage VRM 1500 1800 2000 2500 3000 4000 5000 6000 Maximum RMS Voltage VRMS 1050 1260 1400 1750 2100 2800 3500 4200 Maximum Peak Recurrent Reverse Voltage VRRM 1500 1800 2000 2500 3000 4000 5000 6000 Average Forward Rectified Current @ TA = 50 oC, Lead length = 0.375 in. (9.5 mm) Peak Forward Surge Current ( 8.3 mSec single half sine wave superimposed on rated load) Maximum Forward Voltage at Rated Forward Current Maximum Average DC Reverse Current At Rated DC Blocking Voltage Typical Junction Capacitance (Note 1) Operating and Storage Temperature Range NOTES: (1) Measured at 1MHz & applied reverse voltage of 4 volts o @ TA = 25 C VOLTS IO 1000 500 200 mA IFSM 35 25 15 AMPS VFM 1.5 3.0 IRM 1.0 4.5 6.0 VOLTS µA CJ 12 pF TJ, TSTG -65 to +150 °C 2.01gp1120 I1 DIOTEC ELECTRONICS CORP. Data Sheet No. HVGP-1000-2B 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 HIGH VOLTAGE DIODE RECTIFIERS RATING & CHARACTERISTIC CURVES FOR SERIES GP1150 - GP1600 50 GP1150-1200 Single Phase, Half wave, 60 Hz Resistive and Inductive Loads Lead Length = 0.375" (9.5 mm) 40 JEDEC Method 8.3 mS Half Sine Wave 30 GP1250-1400 20 GP1500-1600 10 Ambient Temperature, oC 0 10 1 FIGURE 1. FORWARD CURRENT DERATING CURVE 100 Number of Cycles at 60 Hz FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT 100 1000 TJ = 100 oC GP1250-1400 10 100 1.0 TJ = 25 oC TJ = 25 oC Non-repetitive Square Pulse 10 0.01 0.1 1.0 10 Pulse Duration (Milliseconds) 0.1 FIGURE 6. PEAK FORWARD SURGE CURRENT 20 60 80 100 120 140 Percent of Rated Peak Reverse Voltage FIGURE 4. TYPICAL REVERSE CHARACTERISTICS 100 TJ = 25 oC 10 0.1 0.1 1 10 100 Reverse Voltage, (Volts) FIGURE 5. TYPICAL JUNCTION CAPACITANCE PER DIODE I2 4.97bhvgp100 DIOTEC ELECTRONICS CORP. Data Sheet No. HVRP-1000-1C 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 MECHANICAL SPECIFICATION FEATURES ACTUAL SIZE OF DO-41 PACKAGE R PROPRIETARY SOFT GLASS JUNCTION PASSIVATION FOR SUPERIOR RELIABILITY AND PERFORMANCE SERIES RP1120 - RP1500 VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM MECHANICAL STRENGTH AND HEAT DISSIPATION (Solder Voids: Typical < 2%, Max. < 10% of Die Area) LL BD (Dia) EXTREMELY LOW LEAKAGE AT HIGH TEMPERATURES LOW FORWARD VOLTAGE DROP BL Color Band Denotes Cathode HIGH CURRENT CAPABILITY MECHANICAL DATA LL DO-41 Case: JEDEC DO-41 molded plastic (U/L Flammability Rating 94V-0) Terminals: Plated axial leads LD (Dia) Soldering: Per MIL-STD 202 Method 208 guaranteed Polarity: Color band denotes cathode Minimum In mm BL 0.160 4.1 Maximum In mm 5.2 0.205 BD 0.103 2.6 0.107 2.7 LL LD 1.00 0.028 25.4 0.71 0.034 0.86 Sym Mounting Position: Any Weight: DO-41 - 0.012 Ounces (0.34 Grams) MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%. PARAMETER (TEST CONDITIONS) RATINGS SYMBOL Series Number UNITS RGP 1120 RGP 1150 RGP 1180 RGP 1200 RGP 1250 RGP 1300 RGP 1400 RGP 1500 Maximum DC Blocking Voltage VRM 1200 1500 1800 2000 2500 3000 4000 5000 Maximum RMS Voltage VRMS 840 1050 1260 1400 1750 2100 2800 3500 Maximum Peak Recurrent Reverse Voltage VRRM 1200 1500 1800 2000 2500 3000 4000 5000 Average Forward Rectified Current @ TA = 50 oC (Lead length = 0.375 in. (9.5 mm)) VOLTS IO 800 400 200 mA Peak Forward Surge Current (8.3 mSec single half sine wave superimposed on rated load) IFSM 30 20 10 AMPS Maximum Forward Voltage at Rated Forward Current VFM 2.5 4.5 6.5 VOLTS Maximum Average DC Reverse Current At Rated DC Blocking Voltage @ TA = 25 C Maximum Reverse Recovery Time (IF=0.5A, IR=1A, IRR=0.25A) Operating and Storage Temperature Range o IRM 1.0 µA TRR 500 nS TJ, TSTG -65 to +125 -65 to +150 °C 2.01rgp1120 I3 DIOTEC ELECTRONICS CORP. Data Sheet No. HVRP-1000-2C 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 HIGH VOLTAGE FAST RECOVERY RECTIFIERS RATING & CHARACTERISTIC CURVES FOR SERIES RGP1120 - RGP1500 50 Single Phase, Half wave, 60 Hz Resistive and Inductive Loads Lead Length = 0.375" (9.5 mm) RGP1120-1180 40 JEDEC Method 8.3 mS Half Sine Wave 30 RGP1200-1300 20 RGP1400-1500 10 Ambient Temperature, oC 0 10 1 FIGURE 1. FORWARD CURRENT DERATING CURVE 100 Number of Cycles at 60 Hz FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT 100 10 o TJ = 25 C Pulse Width = 300 µS 1% Duty Cycle 1.0 10 0.1 0.1 0.1 0.01 Instantaneous Forward Voltage (Volts) 10 FIGURE 4. TYPICAL JUNCTION CAPACITANCE FIGURE 3. TYPICAL FORWARD CHARACTERISTIC 50 Ω noninductive 1 Reverse Voltage, (Volts) 10 Ω noninductive TRR 0.5 D.U.T. (+) (-) 25 VDC (APPROX) 0.0 PULSE GENERATOR (Note 2) (-) 1Ω noninductive (+) -0.5 OSCILLOSCOPE (Note 1) -1.0 NOTES: (1) Rise time = 7nS max., input impedance = 1 Megohm, 22 pF (2) Rise time = 10nS max., source impedance = 50 ohms Set time base for 10nS/cm 1 cm FIGURE 5. REVERSE RECOVERY TEST SETUP AND TIME CHARACTERISTIC I4 4.97bhvrp100 SILICON DIODE CROSS REFERENCE SUGGESTED INDUSTRY DIOTEC PAGE PART NO. REPLACEMENT NO. PART NO. 1N4001 1N4001 H1 1N4001GP 1N4001G H3 1N4002 1N4002 H1 1N4002GP 1N4002G H3 1N4003 1N4003 H1 1N4003GP 1N4003G H3 1N4004 1N4004 H1 1N4004GP 1N4004G H3 1N4005 1N4005 H1 1N4005GP 1N4005G H3 1N4006 1N4006 H1 1N4006GP 1N4006G H3 1N4007 1N4007 H1 1N4007GP 1N4007G H3 1N4933 1N4933 H21 1N4933GP RGP100 H25 1N4934 1N4934 H21 1N4934GP RGP101 H25 1N4935 1N4935 H21 1N4935GP RGP102 H25 1N4936 1N4936 H21 1N4936GP RGP104 H25 1N4937 1N4937 H21 1N4937GP RGP106 H25 1N4942 RGP102 H25 1N4942GP RGP102 H25 1N4944 RGP104 H25 1N4944GP RGP104 H25 1N4946 RGP106 H25 1N4946GP RGP106 H25 1N4947 RGP108 H25 1N4947GP RGP108 H25 1N4948 RGP110 H25 1N4948GP RGP110 H25 1N5059(GP) RGP102 H25 1N5060(GP) RGP104 H25 1N5061(GP) RGP106 H25 1N5062(GP) RGP108 H25 1N5391 1N5391 H7 1N5391GP 1N5391 H7 1N5392 1N5392 H7 1N5392GP 1N5392 H7 1N5393 1N5393 H7 1N5393GP 1N5393 H7 1N5394 1N5395 H7 1N5394GP 1N5395 H7 1N5395 1N5395 H7 1N5395GP 1N5395 H7 1N5396 1N5397 H7 1N5396GP 1N5397 H7 1N5397 1N5397 H7 1N5397GP 1N5397 H7 1N5398 1N5398 H7 1N5398GP 1N5398 H7 1N5399 1N5399 H7 1N5399GP 1N5399 H7 1N5400 1N5400 H11 1N5401 1N5401 H11 1N5402 1N5402 H11 1N5403 1N5404 H11 1N5404 1N5404 H11 1N5405 1N5406 H11 1N5406 1N5406 H11 INDUSTRY PART NO. 1N5615(GP) 1N5616(GP) 1N5617(GP) 1N5618(GP) 1N5619(GP) 1N5620(GP) 1N5621(GP) 1N5622(GP) 1N5623(GP) 1N5624(GP) 1N5625(GP) 1N5626(GP) 1N5627(GP) 6A05 6A05G 6A1 6A1G 6A2 6A2G 6A4 6A4G 6A6 6A6G 6A8 6A10 BY214-50 BY214-100 BY214-200 BY214-400 BY214-600 BY218-100 BY218-200 BY218-400 BY218-600 BY233-200A BY233-400A BY233-600A BY251 BY252 BY253 BY254 BY254S BY255 BY296 BY297 BY296 BY298 BY299 BY396 BY397 BY398 BY399 BYT13-600 BYT13-800 BYT71-100A BYT71-400A BYT71-600A BYW32 BYW33 BYW34 BYW35 BYW36 BYW72 SUGGESTED DIOTEC PAGE REPLACEMENT NO. PART NO. RGP102 H25 RGP104 H25 RGP104 H25 RGP106 H25 RGP106 H25 RGP108 H25 RGP108 H25 RGP110 H25 RGP110 H25 RGP302 H31 RGP304 H31 RGP306 H31 RGP308 H31 GP600 H17 GP600 H17 GP601 H17 GP601 H17 GP602 H17 GP602 H17 GP604 H17 GP604 H17 GP606 H17 GP606 H17 GP608 H17 GP610 H17 GP600 H17 GP601 H17 GP602 H17 GP604 H17 GP606 H17 RGP301 H31 RGP302 H31 RGP304 H31 RGP306 H31 RGP802 H35 RGP804 H35 RGP806 H35 GP402 H15 GP404 H15 GP406 H15 GP408 H15 GP410 H15 GP410 H15 RGP301 H31 RGP302 H31 RGP304 H31 RGP306 H31 RGP308 H31 RGP301 H31 RGP302 H31 RGP304 H31 RGP308 H31 RGP306 H31 RGP308 H31 RGP801 H35 RGP804 H35 RGP806 H35 RGP202 H27 RGP204 H27 RGP204 H27 RGP206 H27 RGP206 H27 RGP302 H31 INDUSTRY PART NO. BYW73 BYW74 BYW75 BYW76 DI750 DI751 DI752 DI754 DIF810 DIF811 DIF812 DIF814 DIF816 DIF817 DIF818 DIF910 DIF911 DIF912 DIF914 DIF916 DIF917 DIF918 DIR500 DIR501 DIR502 DIR504 DIR506 DIR508 DIR510 ESM765-100A ESM765-200A ESM765-400A ESM765-600A FR101 FR101G FR102 FR102G FR103 FR103G FR104 FR104G FR105 FR105G FR106 FR107 FR151 FR151G FR152 FR152G FR153 FR153G FR154 FR154G FR155 FR155G FR156 FR157 FR201 FR201G FR202 FR202G FR203 FR203G SUGGESTED DIOTEC PAGE REPLACEMENT NO. PART NO. RGP304 H31 RGP304 H31 RGP306 H31 RGP306 H31 GP600 H17 GP601 H17 GP602 H17 GP604 H17 RP100 H23 RP101 H23 RP102 H23 RP104 H23 RP106 H23 RP108 H23 RP110 H23 RGP300 H31 RGP301 H31 RGP302 H31 RGP304 H31 RGP306 H31 RGP308 H31 RGP310 H31 GP400 H15 GP401 H15 GP402 H15 GP404 H15 GP406 H15 GP408 H15 GP410 H15 RGP801 H35 RGP802 H35 RGP804 H35 RGP806 H35 RP100 H23 RGP100 H25 RP101 H23 RGP101 H25 RP102 H23 RGP102 H25 RP104 H23 RGP104 H25 RP106 H23 RGP106 H25 RP108 H23 RP110 H25 RGP200 H27 RGP200 H27 RGP201 H27 RGP201 H27 RGP202 H27 RGP202 H27 RGP204 H27 RGP204 H27 RGP206 H27 RGP206 H27 RGP206 H27 RGP208 H27 RGP200 H27 RGP200 H27 RGP201 H27 RGP201 H27 RGP202 H27 RGP202 H27 SUGGESTED INDUSTRY DIOTEC PAGE PART NO. REPLACEMENT NO. PART NO. FR204 RGP204 H27 FR204G RGP204 H27 FR205 RGP206 H27 FR205G RGP206 H27 FR206 RGP208 H27 FR207 RGP210 H27 FR301 RP300 H29 FR301G RGP300 H31 FR302 RP301 H29 FR302G RP301 H31 FR303 RP302 H29 FR303G RGP302 H31 FR304 RP304 H29 FR304G RGP304 H31 FR305 RP306 H29 FR305G RGP306 H31 FR306 RP308 H29 FR307 RGP308 H31 FR501 RP600 H33 FR502 RP601 H33 FR503 RP602 H33 FR504 RP604 H33 FR505 RP606 H33 FR506 RP608 H33 FR507 RP601 H33 FR601 RP600 H33 FR601G RP600 H33 FR602 RP601 H33 FR602G RP601 H33 FR603 RP602 H33 FR603G RP602 H33 FR604 RP604 H33 FR604G RP604 H33 FR605 RP606 H33 FR605G RP606 H33 FR606 RP608 H33 FR607 RP610 H33 FR801 RGP800 H35 FR802 RGP801 H35 FR803 RGP802 H35 FR804 RGP804 H35 FR805 RGP806 H35 GI750 GP600 H17 GI751 GP601 H17 GI752 GP602 H17 GI754 GP604 H17 GI756 GP606 H17 GI758 GP608 H17 GI810 RGP200 H27 GI811 RGP201 H27 GI812 RGP202 H27 GI814 RGP204 H27 GI816 RGP206 H27 GI817 RGP208 H27 GI818 RGP210 H27 GI820 RP600 H33 GI821 RP601 H33 GI822 RP602 H33 GI824 RP604 H33 GI826 RP606 H33 GP10A GP100 H5 GP10B GP101 H5 GP10D GP102 H5 V-1 DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd. Unit B Gardena, CA 90248 PH: 310-767-1052 FX: 310-767-7958 e-mail: [email protected] SILICON DIODE CROSS REFERENCE (Cont'd) INDUSTRY PART NO. GP10G GP10J GP10K GP10M GP15A GP15B GP15D GP15G GP15J GP15K GP15M GP20A GP20B GP20D GP20G GP20J GP20K GP20M GP30A GP30B GP30D GP30G GP30J GP30K GP30M JO5 JO5G J1 J1G J2 J2G J4 J4G J6 J6G J8 J10 MR500 MR501 MR502 MR504 MR506 MR508 MR510 MR750 MR751 MR752 MR754 MR756 MR758 MR760 P300A P300B P300D P300G P300J P300K P300M P511 P513 P600A P600B P600D SUGGESTED DIOTEC PAGE REPLACEMENT NO. PART NO. GP104 H5 GP106 H5 GP108 H5 GP110 H5 GP200 H9 GP201 H9 GP202 H9 GP204 H9 GP206 H9 GP208 H9 GP210 H9 GP200 H9 GP201 H9 GP202 H9 GP204 H9 GP206 H9 GP208 H9 GP210 H9 GP400 H15 GP401 H15 GP402 H15 GP404 H15 GP406 H15 GP408 H15 GP410 H15 GP200 H9 RGP200 H27 GP201 H9 RGP201 H27 GP202 H9 RGP202 H27 GP204 H9 RGP204 H27 GP206 H9 RGP206 H27 GP208 H9 GP210 H9 GP400 H15 GP401 H15 GP402 H15 GP404 H15 GP406 H15 GP408 H15 GP410 H15 GP400 H15 GP600 H17 GP601 H17 GP602 H17 GP604 H17 GP608 H17 GP610 H17 GP400 H15 GP401 H15 GP402 H15 GP404 H15 GP406 H15 GP408 H15 GP410 H15 RGP1150 I3 RGP1180 I3 GP600 H17 GP601 H17 GP602 H17 SUGGESTED INDUSTRY DIOTEC PAGE PART NO. REPLACEMENT NO. PART NO. P600G GP604 H17 P600J GP606 H17 P600K GP608 H17 P600M GP610 H17 PF4HZ GP404 H15 PF6HZ GP406 H15 PF8HZ GP408 H15 PFR850 RP300 H29 PFR851 RP301 H29 PFR852 RP302 H29 PFR854 RP304 H29 PFR856 RP306 H29 PL4HZ 1N4004G H33 PL6HZ 1N4006G H33 PL8HZ 1N4008G H33 PLR810 RGP200 H27 PLR811 RGP201 H27 PLR812 RGP202 H27 PLR813 RGP204 H27 PLR814 RGP204 H27 PLR816 RGP206 H27 PLR817 RGP208 H27 PLR818 RGP210 H27 PR1001 RP100 H23 PR1002 RP101 H23 PR1003 RP102 H23 PR1004 RP104 H23 PR1005 RP106 H23 PR1006 RP108 H23 PR1007 RP110 H23 PR121 GP1120 I1 PR141 RGP1150 H27 PR1501 RGP200 H27 PR1502 RGP201 H27 PR1503 RGP202 H27 PR1504 RGP204 H27 PR1505 RGP206 H27 PR1506 RGP206 H27 PR1507 RGP208 H27 PR3001 RP300 H29 PR3002 RP301 H29 PR3003 RP302 H29 PR3004 RP304 H29 PR3005 RP306 H29 PR3006 RP308 H29 PR3007 RP308 H29 PR6001 RP600 H33 PR6002 RP601 H33 PR6003 RP602 H33 PR6004 RP604 H33 PR6005 RP606 H33 PR6006 RP608 H33 PR6007 RP610 H33 PX4A01 GP400 H15 PX4A02 GP401 H15 PX4A03 GP402 H15 PX4A04 GP404 H15 PX4A05 GP406 H15 PX4A06 GP408 H15 PX4A07 GP410 H15 PX6A01 RP600 H17 PX6A02 GP601 H17 PX6A03 GP602 H17 SUGGESTED INDUSTRY DIOTEC PART NO. REPLACEMENT PART NO. PX6A04 GP604 PX6A05 GP606 PX6A06 GP608 PX6A07 GP610 PY124 RGP202 PY125 GP204 PY126 GP206 PY55-350 RGP204 PY55-600 RGP206 RG4A RGP300 RG4B RGP301 RG4D RGP302 RG4G RGP304 RG4J RGP306 RG4K RGP308 RG4M RGP310 RGP10A RGP100 RGP10B RGP101 RGP10D RGP102 RGP10G RGP104 RGP10J RGP106 RGP10K RGP108 RGP10M RGP110 RGP15A RGP200 RGP15B RGP201 RGP15D RGP202 RG1A RGP100 RG1B RGP101 RG1D RGP102 RG1G RGP104 RG1J RGP106 RG1K RGP108 RG1M RGP110 RG2A RGP200 RG2B RGP201 RG2D RGP202 RG2G RGP204 RG2J RGP206 RG2K RGP208 RG2M RGP210 RG3A RGP300 RG3B RGP301 RG3D RGP302 RG3G RGP304 RG3J RGP306 RG3K RGP308 RG3M RGP310 RGP15G RGP204 RGP15J RGP206 RGP15K RGP208 RGP15M RGP210 RGP20A RGP200 RGP20B RGP201 RGP20D RGP202 RGP20G RGP204 RGP20J RGP206 RGP20K RGP208 RGP20M RGP210 RGP25A RGP300 RGP25B RGP301 RGP25D RGP302 RGP25G RGP304 RGP25J RGP306 PAGE NO. H17 H17 H17 H17 H27 H9 H9 H27 H27 H31 H31 H31 H31 H31 H31 H31 H25 H25 H25 H25 H25 H25 H25 H27 H27 H27 H25 H25 H25 H25 H25 H25 H25 H27 H27 H27 H27 H27 H27 H27 H31 H31 H31 H31 H31 H31 H31 H27 H27 H27 H27 H27 H27 H27 H27 H27 H27 H27 H31 H31 H31 H31 H31 SUGGESTED INDUSTRY DIOTEC PAGE PART NO. REPLACEMENT NO. PART NO. RGP25K RGP308 H31 RGP25M RGP310 H31 RGP30A RGP300 H31 RGP30B RGP301 H31 RGP30D RGP302 H31 RGP30G RGP304 H31 RGP30J RGP306 H31 RGP30K RGP308 H31 RGP30M RGP310 H31 RL201 GP200 H9 RL201G GP200 H9 RL202 GP201 H9 RL202G GP201 H9 RL203 GP202 H9 RL203G GP202 H9 RL204 GP204 H9 RL204G GP204 H9 RL205 GP206 H9 RL205G GP206 H9 RL206 GP208 H9 RL207 GP210 H9 RS8AT RGP800 H35 RS8BT RGP801 H35 RS8DT RGP802 H35 RS8GT RGP804 H35 RS8JT RGP806 H35 V322 GP402 H15 V324 GP404 H15 V326 GP406 H15 V328 GP408 H15 V330 GP400 H15 V330X RGP300 H31 V331 GP401 H15 V331X RGP301 H31 V332 GP402 H15 V332X RGP302 H31 V334 GP404 H15 V334X RGP304 H31 V336 GP406 H15 V336X RGP306 H31 V342 GP404 H15 V344 GP404 H15 V346 GP406 H15 V348 GP408 H15 V350 GP400 H15 V350X RGP300 H31 V351 GP401 H15 V351X RGP301 H31 V3510 GP410 H15 V352 GP402 H15 V352X RGP302 H31 V354 GP404 H15 V354X RGP304 H31 V356 GP406 H15 V356X RGP306 H31 V358 GP408 H15 V-2 DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd. Unit B Gardena, CA 90248 PH: 310-767-1052 FX: 310-767-7958 e-mail: [email protected] DIOTEC ELECTRONICS CORPORATION SAMPLE REQUEST FORM TO EXPEDITE YOUR REQUEST FOR PRODUCT SAMPLES, PLEASE FILL OUT THIS FORM AND FAX IT TO US AT: 310-767-7958 NOTE: DIOTEC ELECTRONICS CORP. IS A LEADING MANUFACTURER OF HIGH QUALITY, HIGH RELIABILTY POWER DIODES AND RECTIFIERS. WE SERVE THE OEM COMMUNITY. RETAIL REQUESTS SHOULD BE DIRECTED TO NTE ELECTRONICS (WWW.NTEINC.COM) OR DIGI-KEY (WWW.DIGIKEY.COM). COMPANY : ENGINEERING CONTACT: CONTACT PHONE NUMBER: CONTACT FAX NUMBER: ADDRESS: CITY STATE DIOTEC PART NUMBER(S): NUMBER OF SAMPLES: ESTIMATED ANNUAL USAGE: TARGET PRICE: APPLICATION: NEW PRODUCT? REDESIGN? NEED ALTERNATE SUPPLIER? CURRENT SUPPLIER: CURRENT PART NUMBER CURRENT PRICE: COMMENTS: web site: www.diotec-usa.com e-mail: [email protected] DIOTEC is thriving while its competitors, big and small are dropping out!! The reasons?? Very simple: (A) DIOTEC offers a very comprehensive line of diodes and rectifiers with excellent qualities. (B) DIOTEC offers the Best Services in the business: (1) Same Day Price Quotation (*) (2) Samples delivered within three days (*) (3) Orders delivered from stock (*) (C) DIOTEC is able and more willing to go the extra distance to assist you with your special requirements (D) DIOTEC offers the most competitive prices. Unlike its major competitors, DIOTEC runs the tightest ship and therefore has the lowest overhead in this business. This allows DIOTEC to keep its costs down and pass the savings on to its valued customers. So discuss your diode and rectifier needs with DIOTEC now. Our knowledgeable sales and technical staffs are ready to help you. THE ONLY QUALITY RECTIFIERS AND DIODES AT COMPETITIVE PRICES (*) Except Specialty items