Series 72 Guardian Lipped Straight Shrink Boots Type 1, 2, and 3 Lipped straight shrink boots Straight boots with lip for attachment to standard circular connector adapters. After shrinking, the boot lip locks into adapter groove. Eyelet hole allows attachment of dust caps or protective covers. Choose Type 1 high performance elastomer for extreme temperatures and excellent resistance to fuels and oils, Type 2 non-halogenated flame-retardant polyolefin for use where limited fire hazard is required, or choose Type 3 general purpose polyolefin for use where occasional exposure to heat and chemicals may occur. Choose boot size based on adapter diameter and cable diameter. Table 1: Boot Size Selection Guide Table 2: Material Selection Guide Adapter Dia. Min. Cable In. Diameter mm. Boot Size Min Max Min Max In. mm. 00 01 02 03 04 05 06 07 08 09 .250 .325 .350 .450 .600 .750 .900 1.250 1.400 1.870 .325 .425 .600 .850 1.000 1.200 1.350 1.650 2.250 2.470 6.35 7.62 8.89 11.43 15.24 19.05 22.86 31.75 35.56 47.50 8.26 10.80 15.24 21.59 25.40 30.48 34.29 41.91 57.15 62.70 .110 .150 .175 .225 .275 .300 .375 .425 .625 .660 2.79 3.81 4.45 5.72 6.99 7.62 9.53 10.80 15.88 16.80 BOOT GROOVE ADAPTER DIAMETER Attribute Type 1 High Performance Semi-Rigid Elastomer Type 2 Zero Halogen Semi-Rigid Polyolefin Type 3 General Purpose Flexible Polyolefin Continuous Operating Temp. Resistance to Fuels, Oils Low Toxicity, Zero Halogen -75° to +150°C Excellent No -30° to +125°C Very Good Yes -55° to +135°C Good No Table 3: Pre-Coated Boots Adhesive Information Attribute W2 Standard Hot Melt Adhesive Boot Material Compatibility Continuous Operating Temp. Resistance to Fuels, Oils, and Fluids Low Toxicity, Zero Halogen Types 1, 2 and 3 -40° to +80°C Good Yes W1 R High High Temperature Hot Performance Melt Adhesive Epoxy Adhesive Types 1, 2 and 3 -55° to +105°C Good Yes Type 1 -75° to +150°C Excellent Yes Lipped straight shrink boots- Type 1 high performance elastomer • -75° C to +150° C • Excellent resistance to fuels, oils, solvents and heat. Semi-rigid high performance boots combine excellent resistance to fuels, oils and solvents with superior performance at extreme temperatures. Rated for 3000 hours continuous operation at +150° C, these boots fit most standard boot adapters for circular connectors. Material meets the requirements of VG95343 Type 6, BSG 198-5-DE, EN62329-102 and SAE AS5258 Type H. These boots are recommended for demanding applications such as military vehicles and petrochemical exploration. Choose standard length or short length if space is limited. Black color. Part Number with Eyelet Guardian Standard Boots: Pre-Coated with Boot No Adhesive W1 Hi-Temp HotSize Lining Melt Adhesive 03 04 05 06 07 Pre-Coated with W2 Standard HotMelt Adhesive Part Number without Eyelet Pre-Coated with R Epoxy Adhesive No Adhesive Lining 770-001S103 770-001S103W1 770-001S103W2 770-001S103R 770-003S103 770-001S104 770-001S104W1 770-001S104W2 770-001S104R 770-003S104 770-001S105 770-001S105W1 770-001S105W2 770-001S105R 770-003S105 770-001S106 770-001S106W1 770-001S106W2 770-001S106R 770-003S106 770-001S107 770-001S107W1 770-001S107W2 770-001S107R 770-003S107 ©2011 Glenair, Inc. CAGE Code 06324 Pre-Coated with W1 Hi-Temp HotMelt Adhesive Pre-Coated with W2 Standard HotMelt Adhesive Pre-Coated with R Epoxy Adhesive Ref Conduit I.D. / Size 770-003S103W1 770-003S104W1 770-003S105W1 770-003S106W1 770-003S107W1 770-003S103W2 770-003S104W2 770-003S105W2 770-003S106W2 770-003S107W2 770-003S103R 770-003S104R 770-003S105R 770-003S106R 770-003S107R 06,09 12,16 20 24 28,32,40 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 44 Series 72 Guardian Lipped Straight Shrink Boots Type 1, 2, and 3 Lipped straight shrink boots- Type 2 zero halogen, semi-rigid • Low Smoke, Zero Halogen • Meets U.S. and E.U. toxicity requirements. Halogen-free polyolefin boots meet low smoke and toxicity requirements of shipboard, transit and aircraft systems. These Low Smoke/Zero Halogen (LSZH) boots fit most standard shrink boot adapters, including M85049 types along with Glenair Series 31 and Series 44 adapters. Oxygen index greater than 30%, smoke index less than 20, and toxicity index under 3 per 100 grams. Material meets requirements of NAVSEA 5617649, VG95343 Part 29, BSG 198-5-DF, EN62329-101 and SAE AS5258 Type G. Good resistance to oils, fuels and solvents. Available high temperature hot melt adhesive lining, these boots provide strain relief and environmental protection to connector/cable transitions. Temperature rating -30° to +125° C. Black color. Part Number with Eyelet Boot Size No Adhesive Lining Part Number without Eyelet Pre-Coated with W1 Hi-Temp HotMelt Adhesive Pre-Coated with W2 Standard HotMelt Adhesive No Adhesive Lining Pre-Coated with W1 Hi-Temp HotMelt Adhesive Pre-Coated with W2 Standard HotMelt Adhesive Ref Conduit I.D. / Size 03 04 770-001S203 770-001S204 770-001S203W1 770-001S204W1 770-001S203W2 770-001S204W2 770-003S203 770-003S204 770-003S203W1 770-003S204W1 770-003S203W2 770-003S204W2 06,09 12,16 05 770-001S205 770-001S205W1 770-001S205W2 770-003S205 770-003S205W1 770-003S205W2 20 06 770-001S206 770-001S207 770-001S206W1 770-001S207W1 770-001S206W2 770-001S207W2 770-003S206 770-003S207 770-003S206W1 770-003S207W1 770-003S206W2 770-003S207W2 24 28,32,40 07 Lipped straight shrink boots- Type 3 polyolefin, flexible • General purpose harnessing • Economical, flexible • -55° C to +135° C Economical flexible polyolefin boots fit most standard shrink boot adapters, Glenair Series 31 and Series 44 adapters. These self-extinguishing boots meet the requirements of SAE AS81765/1 Type II. Good resistance to oils and fuels. Available with optional hot melt adhesive lining, these boots provide strain relief and environmental protection to connector/ cable transitions. Temperature rating -55° to +135° C. Black color. Part Number with Eyelet Boot Size 03 04 05 06 07 ©2011 Glenair, Inc. No Adhesive Lining 770-001S303 770-001S304 770-001S305 770-001S306 770-001S307 Part Number without Eyelet Pre-Coated with W1 Hi-Temp HotMelt Adhesive Pre-Coated with W2 Standard HotMelt Adhesive 770-001S303W1 770-001S304W1 770-001S305W1 770-001S306W1 770-001S307W1 770-001S303W2 770-001S304W2 770-001S305W2 770-001S306W2 770-001S307W2 No Adhesive Lining 770-003S303 770-003S304 770-003S305 770-003S306 770-003S307 CAGE Code 06324 Pre-Coated with W1 HiTemp Hot-Melt Adhesive Pre-Coated with W2 HotMelt Adhesive 770-003S303W1 770-003S304W1 770-003S305W1 770-003S306W1 770-003S307W1 770-003S303W2 770-003S304W2 770-003S305W2 770-003S306W2 770-003S307W2 Ref Conduit I.D. / Size 06,09 12,16 20 24 28,32,40 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 45 Series 72 Guardian Lipped Straight Shrink Boots Dimensions and Part Marking Lipped straight shrink boots- dimensions Ø.079 (2.0) REF D E B A F C H STANDARD LENGTH AFTER SHRINKING (RECOVERED) AS SUPPLIED (EXPANDED) Entry Code Boot Size 06, 09 12, 16 20 24 28, 32, 40 03 04 05 06 07 A Min. In. mm. .945 1.181 1.260 1.417 1.693 24.0 30.0 32.0 36.0 43.0 B Max. In. mm. C ± 20% In. mm. .197 .236 .276 .335 .394 .035 .039 .047 .047 .051 5.0 6.0 7.0 8.5 10.0 G 0.9 1.0 1.2 1.2 1.3 D ± 10% In. mm. 1.496 2.165 2.638 3.150 3.898 38.0 55.0 67.0 80.0 99.0 E Ref. In. mm. .748 1.181 1.299 1.575 2.165 19.0 30.0 33.0 40.0 55.0 F Max. In. mm. .413 .551 .709 .866 1.102 10.5 14.0 18.0 22.0 28.0 G Ref. In. mm. .520 .693 .850 .945 1.276 13.2 17.6 21.6 24.0 32.4 H ± 30% In. mm. .063 .071 .071 .079 .087 1.6 1.8 1.8 2.0 2.2 Lipped straight shrink boots- part marking, raised lettering RECOVERED EXPANDED BOOT SIZE CODE LETTER “S” INDICATES STRAIGHT BOOT LETTER “C” INDICATES CABLE END ©2011 Glenair, Inc. LETTER “A” INDICATES ADAPTER (CONNECTOR) END CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 46