CVS575 Voltage Controlled SAW Oscillator 3.3V LVPECL 5×7.5mm SMD Model CVS575 is a SAW(surface acoustic wave) based Voltage Controlled Oscillator (VCSO) designed for High Performance PLLs. It is an ideal choice for Telecommunication applications needing to meet Low Jitter generation requirements. It is housed in the industry standard 5×7.5×2.5mm SMD package. The Enable/Disable function was designed to be used with CMOS logic levels for ease of interfacing. It is not necessary to convert to LVPECL logic to turn the Output ON and OFF. Rev: L Date: 27-Aug-2015 Page 1 of 2 CRYSTEK CORPORATION 12730 Commonwealth Drive • Fort Myers, Florida 33913 Phone: 239-561-3311 • 800-237-3061 Fax: 239-561-1025 • www.crystek.com CVS575 Voltage Controlled SAW Oscillator 3.3V LVPECL 5×7.5mm SMD Performance Specification MIN Nominal Frequency: 315 Absolute Pulling Range: ±50 Frequency Stability: TYP MAX UNITS 1000 MHz 0.295 -0.008 +0.035 (7.50 -0.20 +0.89) CVS575 Freq XXXX XX ppm ±150 ppm Linearity: ±15 % Tuning Sensitivity, Kv: +275 ppm/V @1kHz Offset -110 dBc/Hz @10kHz Offset -130 dBc/Hz @100kHz Offset -149 dBc/Hz @1MHz Offset -150 dBc/Hz @10MHz Offset -151 dBc/Hz 0.18 0.12 pS, RMS pS, RMS Denotes pad 1 XXXX=Date Code XX=Lot Code Output Phase Noise: (622.08 MHz) 0.099 (2.50) 0.046 (1.16) 0.058 (1.47) Jitter: 12kHz-20MHz Rise/Fall Times, tr/tf 20-80% 100 240 pS Output High Voltage, VOH 2.215 2.420 V Output Low Voltage, VOL 1.470 1.745 V Enable High Voltage, VIH 2.0 Vcc V Disable Low Voltage, VIL GND 0.8 V Enable High Current, IIH +150 uA Disable Low Current, IIL -150 uA Duty Cycle: 45 50 55 % Supply Voltage: 3.0 3.3 3.6 V Supply Current, Icc: Control Voltage: 82 0 3.3 kΩ Input Modulation: 500 kHz Operating Temperature: -20 +70 °C Storage Temperature: -45 +90 °C Parameter Conditions Mechanical Shock MIL-STD-883, Method 2002 Mechanical Vibration MIL-STD-883, Method 2007 Solderability MIL-STD-883, Method 2003 Resistance to Solvents MIL-STD-883, Method 2015 #3 #6 #5 #4 0.046 (1.16) Pad Connection 1 2 3 4 5 6 Volt Cntrl E/D GND OUT COUT Vdd SUGGESTED PAD LAYOUT 0.050 (1.27) 0.01µF 6 5 4 0.154 (3.91) 0.071 (1.80) 1 2 3 0.100 (2.54) 0.200 (5.08) V 100 #2 via to ground mA Input Impedance: #1 0.100 (2.54) 0.200 (5.08) RECOMMENDED REFLOW SOLDERING PROFILE Ramp-Up 3°C/Sec Max. 260°C TEMPERATURE SONET OC-48 (12kHz~20MHz) SONET OC-192 (50kHz~80MHz) 0.200 ±0.015 (5.08 ±0.38) Critical Temperature Zone Ramp-Down 6°C/Sec. 217°C 200°C 150°C Preheat 180 Secs. Max. 90 Secs. Max. 8 Minutes Max. 260°C for 10 Secs. Max. NOTE: Reflow Profile with 240°C peak also acceptable. Rev: L Date: 27-Aug-2015 Page 2 of 2 CRYSTEK CORPORATION 12730 Commonwealth Drive • Fort Myers, Florida 33913 Phone: 239-561-3311 • 800-237-3061 Fax: 239-561-1025 • www.crystek.com