CRYSTEKCRYSTAL CCSO-914X3-1000

CCSO-914X3-1000
True SineWave
SAW Based Clock Osc
9x14MM SMD
3.3 Volt
Ultra-Low Phase Noise 1GHz SAW Clock
CCSO-914X3-1000
Model CCSO-914X3-1000 is a 1GHz SAW (surface acoustic wave) Clock Oscillator
(CCSO). SAW crystal technology provides low-noise and low-jitter performance
with true sinewave output. Features include -142dBc/Hz phase noise at 10kHz offset,
3.3V input voltage, -40 to +85C operating temperature, FR5 PCB and 9x14 mm SMT
package. The oscillator has no sub-harmonic and the second harmonic is typically
-25dBc.
Applications include:
System Clock for Network Clock Generator/Synchronizer, Clock for DDS, Test and
Measurement, Avionics, Point-to-Point Radios, and Multi-point Radios.
Rev.: A
Date: 10-23-07
CCSO-914X3-1000
True SineWave
SAW Based Clock Osc
9x14MM SMD
3.3 Volt
Frequency :
Temperature Range:
Storage:
Input Voltage:
1 GHz
-40°C to 85°C
-45°C to 90°C
3.3V ± 0.15V
Freq. vs Temp.
Input Current:
Output:
Output Power:
Start-up time:
2nd Harmonic:
Sub-harmonics:
Modulation BW:
Jitter:
SONET OC-48(12KHz~20MHz)
SONET OC-192(50KHz~80MHz)
±120ppm Typ.
25mA Typ., 35mA Max
True SineWave
+5dBm Min. into 50 Ohm Load
2ms Typ., 10ms Max
-25dBc Typ., -20dBc Max
None
>20KHz @ -3dB
Phase Noise Typical:
1KHz
10KHz
100KHz
1MHz
10MHz
0.18ps RMS Typ., 0.20ps RMS Max
0.12ps RMS Typ., 0.15ps RMS Max
-112 dBc/Hz
-142 dBc/Hz
-155 dBc/Hz
-167 dBc/Hz
-168 dBc/Hz
0.560
(14.2)
0.360
(9.14)
0.040
(1.01)
CRYSTEK
Part Number
Freq
Date Code
1
2
4
3
0.070
(1.77)
1
0.200
(5.08)
SUGGESTED PAD LAYOUT
0.560
(14.2)
0.210
(5.3)
Pad
0.050
(1.27)
Connection
N/C
2
GND
3
Output
4
Vdd
0.090
(2.28)
0.280
(7.11)
0.200
(5.08)
Rev.: A
Date: 10-23-07
CCSO-914X3-1000
True SineWave
SAW Based Clock Osc
9x14MM SMD
3.3 Volt
CCSO-914X3-1000
Actual Plot
Frequency VS Temperature
RECOMMENDED REFLOW SOLDERING PROFILE
Ramp-Up
3°C/Sec Max.
TEMPERATURE
260°C
217°C
Critical
Temperature Zone
Ramp-Down
6°C/Sec.
200°C
150°C
Preheat
180 Secs. Max.
8 Minutes Max.
90 Secs. Max.
260°C for
10 Secs. Max.
NOTE: Reflow Profile with 240°C peak also acceptable.
Parameter
Mechanical Shock
Mechanical Vibration
Solderability
Solvent Resistance
Resistance to Soldering Heat
Thermal Shock
Moisture Resistance
Conditions
MIL-STD-883, Method 2002, Condition B
MIL-STD-883, Method 2007, Condition A
MIL-STD-883, Method 2003
MIL-STD-202, Method 215
MIL-STD-202, Method 210, Condition I or J
MIL-STD-883, Method 1011, Condition A
MIL-STD-883, Method 1004
Rev.: A
Date: 10-23-07