CVCSO-914-1000 Ultra-Low Phase Noise 1GHz SAW VCSO True SineWave SAW Based VCSO 9×14mm SMD 5 Volt 5d -13 K STE CRYSO-914 CVC00 MHz 10 z /H Bc Model CVCSO-914-1000 is a 1 GHz voltage-controlled SAW (surface acoustic wave) Clock Oscillator (VCSO). SAW crystal technology provides low-noise and low-jitter performance with true sinewave output. Features include -138 dBc/Hz phase noise at 10 kHz offset, 5V input voltage, -20°C to +70°C operating temperature, and 9×14 mm SMT package. The CVCSO-914X offers an operating temperature range of -40°C to +85°C. The oscillator has no sub-harmonic and the second harmonic is typically -20 dBc. Applications include PLL frequency translation, test and measurement, avionics, point-to-point radios, and multi-point radios. Rev: R Date: 25-Aug-2015 Page 1 of 3 CRYSTEK CORPORATION 12730 Commonwealth Drive • Fort Myers, Florida 33913 Phone: 239-561-3311 • 800-237-3061 Fax: 239-561-1025 • www.crystek.com CVCSO-914-1000 True SineWave SAW Based VCSO 9×14mm SMD 1 GHz 5 Volt -20°C to +70°C Frequency: Temperature Range: CVCSO-914X-1000 option Storage: Input Voltage: Control Voltage Range: Settability At Nominal (25°C): Tuning Sensitivity (Kv): Frequency vs Temperature: Input Current: -40°C to +85°C -40°C to 90°C 5.0V ±0.25V 0V to 5.0V +0.5V to 2.0V +120ppm/V ±100ppm Typical 25mA Typical, 35mA Max Output: Pullability APR: Linearity: Output Power: Start-Up Time: 2nd Harmonic: Sub-Harmonics: Modulation BW: Phase Noise Typical: 1kHz 10kHz 100kHz 1MHz 10MHz G-sensitivity: True SineWave ±50ppm Min ±20% Max +10dBm Min into 50 Ω Load 2mSec Typical, 10mSec Max -20dBc Typical, -15dBc Max None >20kHz @ -3dB -105 dBc/Hz -138 dBc/Hz -150 dBc/Hz -160 dBc/Hz -170 dBc/Hz 0.9×10-9 per g SUGGESTED PAD LAYOUT 0.040 (1.01) 0.090 (2.29) 0.050 (1.27) 0.560 ±0.010 (14.2 ±0.25) 0.360 ±0.005 (9.14 ±0.13) CRYSTEK CVCSO-914 1 GHz Date Code 0.090 (2.29) 0.180 (4.57) 0.125 (3.18) 0.560 ±0.010 (14.2 ±0.25) 0.210 Max (5.3) CRYSTEK CORPORATION 1 2 4 3 0.100 (2.54) 0.280 (7.11) 0.040 (1.02) 0.050 (1.27) 0.280 (7.11) 0.200 (5.08) 0.200 (5.08) Pad Connection 1 2 3 4 Volt. Control GND Output Vdd Rev: R Date: 25-Aug-2015 Page 2 of 3 12730 Commonwealth Drive • Fort Myers, Florida 33913 Phone: 239-561-3311 • 800-237-3061 Fax: 239-561-1025 • www.crystek.com CVCSO-914-1000 True SineWave SAW Based VCSO 9×14mm SMD 5 Volt Frequency vs Temperature RECOMMENDED REFLOW SOLDERING PROFILE TEMPERATURE Ramp-Up 3°C/Sec Max. 260°C Critical Temperature Zone Ramp-Down 6°C/Sec. 217°C 200°C 150°C Preheat 180 Secs. Max. 8 Minutes Max. 90 Secs. Max. 260°C for 10 Secs. Max. NOTE: Reflow Profile with 240°C peak also acceptable. Parameter Conditions Mechanical Shock MIL-STD-883, Method 2002, Condition B Mechanical Vibration MIL-STD-883, Method 2007, Condition A Solderability MIL-STD-883, Method 2003 Solvent Resistance MIL-STD-202, Method 215 Resistance to Soldering Heat MIL-STD-202, Method 210, Condition I or J Thermal Shock MIL-STD-883, Method 1011, Condition A Moisture Resistance MIL-STD-883, Method 1004 CRYSTEK CORPORATION Rev: R Date: 25-Aug-2015 Page 3 of 3 12730 Commonwealth Drive • Fort Myers, Florida 33913 Phone: 239-561-3311 • 800-237-3061 Fax: 239-561-1025 • www.crystek.com