CCSO-914X3-1000 Ultra-Low Phase Noise 1GHz SAW Clock True SineWave SAW Based Clock Oscillator 9×14mm SMD 3.3 Volt Model CCSO-914X3-1000 is a 1 GHz SAW (surface acoustic wave) Clock Oscillator (CCSO). SAW crystal technology provides low-noise and low-jitter performance with true sinewave output. Features include -142dBc/Hz phase noise at 10kHz offset, 3.3V input voltage, -40°C to +85°C operating temperature, FR5 PCB and 9×14 mm SMT package. The oscillator has no sub-harmonic and the second harmonic is typically -25dBc. Applications include: System Clock for Network Clock Generator/Synchronizer, Clock for DDS, Test and Measurement, Avionics, Point-to-Point Radios, and Multi-point Radios. Rev: H Date: 20-Jul-2015 Page 1 of 3 CRYSTEK CORPORATION 12730 Commonwealth Drive • Fort Myers, Florida 33913 Phone: 239-561-3311 • 800-237-3061 Fax: 239-561-1025 • www.crystek.com CCSO-914X3-1000 True SineWave SAW Based Clock Oscillator 9×14mm SMD 3.3 Volt Frequency: Temperature Range: Storage: Input Voltage: 1 GHz -40°C to +85°C -45°C to 90°C 3.3V ± 0.15V Frequency vs Temperature: Input Current: Output: Output Power: Start-Up Time: 2nd Harmonic: Sub-Harmonics: Jitter: SONET OC-48(12kHz~80MHz) SONET OC-192(50kHz~80MHz) ±150ppm Typical 25mA Typical, 35mA Max True SineWave +5dBm Min into 50 Ω Load 2mSec Typical, 10mSec Max -25dBc Typical, -20dBc Max None 0.18ps RMS Typical, 0.20ps RMS Max 0.12ps RMS Typical, 0.15ps RMS Max Phase Noise Typical: 1kHz 10kHz 100kHz 1MHz 10MHz -112 dBc/Hz -142 dBc/Hz -155 dBc/Hz -167 dBc/Hz -168 dBc/Hz G-sensitivity: 0.9×10-9 per g 0.090 (2.29) SUGGESTED PAD LAYOUT 0.040 (1.01) 0.050 (1.27) 0.560 (14.2) 0.360 (9.14) CRYSTEK CCSO-914X3 1 GHz Date Code 0.090 (2.29) 0.180 (4.57) 0.125 (3.18) 0.560 (14.2) 0.210 (5.3) CRYSTEK CORPORATION 1 2 4 3 0.100 (2.54) 0.280 (7.11) 0.040 (1.02) 0.050 (1.27) 0.280 (7.11) 0.200 (5.08) 0.200 (5.08) Pad Connection 1 2 3 4 N/C GND Output Vdd Rev: H Date: 20-Jul-2015 Page 2 of 3 12730 Commonwealth Drive • Fort Myers, Florida 33913 Phone: 239-561-3311 • 800-237-3061 Fax: 239-561-1025 • www.crystek.com CCSO-914X3-1000 True SineWave SAW Based Clock Oscillator 9×14mm SMD 3.3 Volt Frequency vs Temperature RECOMMENDED REFLOW SOLDERING PROFILE TEMPERATURE Ramp-Up 3°C/Sec Max. 260°C Critical Temperature Zone Ramp-Down 6°C/Sec. 217°C 200°C 150°C Preheat 180 Secs. Max. 8 Minutes Max. 90 Secs. Max. 260°C for 10 Secs. Max. NOTE: Reflow Profile with 240°C peak also acceptable. Parameter Conditions Mechanical Shock MIL-STD-883, Method 2002, Condition B Mechanical Vibration MIL-STD-883, Method 2007, Condition A Solderability MIL-STD-883, Method 2003 Solvent Resistance MIL-STD-202, Method 215 Resistance to Soldering Heat MIL-STD-202, Method 210, Condition I or J Thermal Shock MIL-STD-883, Method 1011, Condition A Moisture Resistance MIL-STD-883, Method 1004 CRYSTEK CORPORATION Rev: H Date: 20-Jul-2015 Page 3 of 3 12730 Commonwealth Drive • Fort Myers, Florida 33913 Phone: 239-561-3311 • 800-237-3061 Fax: 239-561-1025 • www.crystek.com