CVHD-950 Model 9×14 mm SMD, 3.3V, CMOS 50 MHz HCMOS 3.3V 80 MHz HCMOS 3.3V K STE CRY -950 D H CV Hz 50 M K STE CRY -950 D H CV Hz 80 M z /H Bc z /H Bc 6d -16 1d -16 100 MHz HCMOS 3.3V 130 MHz HCMOS 3.3V K STE CRY -950 D CVH Hz M 130 K STE CRY -950 D H CV MH z 100 4d -16 z /H Bc z /H Bc 8d -16 Model CVHD-950 is a 50 MHz to 130 MHz CMOS Voltage Controlled Crystal Oscillator. High Q crystal and 3rd overtone technology provides Ultra-Low Phase Noise and Low-Jitter performance with a CMOS output. Features include -165 dBc/Hz phase noise floor with 3.3Vdc input voltage, -40°C to +85°C operating temperature, and 9×14 mm SMT package. The oscillator has no sub-harmonics. Applications include High Definition TV, Avionics Low Phase Signal Sources, and Test and Measurement. CRYSTEK CORPORATION Rev: R Date: 25-Jun-2015 Page 1 of 3 12730 Commonwealth Drive • Fort Myers, Florida 33913 Phone: 239-561-3311 • 800-237-3061 Fax: 239-561-1025 • www.crystek.com CVHD-950 Model 9×14 mm SMD, 3.3V, CMOS Frequency Range: Temperature Range: (Option M) (Option X) Storage: Input Voltage: Supply Pushing: Input Current: Output: Symmetry: Rise/Fall Time: Logic: 50 MHz to 130 MHz 0°C to +70°C (standard) -20°C to +70°C -40°C to +85°C -45°C to 90°C 3.3V ±0.3V 1.2ppm/V Typical 15mA Typical, 25mA Max CMOS 45/55% Max @ 50%Vdd 3nsec Max @ 20% to 80% Vdd “0” = 10% Vdd Max “1” = 90% Vdd Min 15pF ±24mA Max Load: Output Current: Input: Modulation Bandwidth: Input Impedance: Control Voltage: Tuning Sensitivity: Frequency Pulling: >10kHz @ -3dB 51 kΩ 1.65V ±1.65V +25ppm/V Typical ±20ppm APR Min Linearity: Phase Jitter (12kHz~80MHz): Typical Phase Noise: 1kHz 10kHz 100kHz 1MHz Phase Noise Floor: Sub-harmonics: Aging: ±10% Max 0.13psec Typical @100MHz (Inclusive of frequency stability, calibration, and aging.) -135 dBc/Hz -155 dBc/Hz -164 dBc/Hz -165 dBc/Hz -165dBc/Hz Typical, -160dBc/Hz Max None <3ppm 1st year, <1ppm thereafter Part Number Example: CVHD-950X-100.000 = 3.3V, 45/55, -40°C to +85°C (±20ppmAPR), 100 MHz Absolute Maximum Ratings CRYSTEK CORPORATION Parameter Rating Unit Input Supply Voltage +6.0 V Input Control Voltage +10.0 V Rev: R Date: 25-Jun-2015 Page 2 of 3 12730 Commonwealth Drive • Fort Myers, Florida 33913 Phone: 239-561-3311 • 800-237-3061 Fax: 239-561-1025 • www.crystek.com CVHD-950 Model 9×14 mm SMD, 3.3V, CMOS 0.360 (9.14) RECOMMENDED REFLOW SOLDERING PROFILE 0.560 (14.2) CRYSTEK Part Number Frequency Date Code Ramp-Up 3°C/Sec Max. TEMPERATURE 0.560 (14.2) 0.210 (5.3) 260°C Critical Temperature Zone Ramp-Down 6°C/Sec. 217°C 200°C 150°C SUGGESTED PAD LAYOUT Preheat 180 Secs. Max. 8 Minutes Max. 0.050 (1.27) 0.040 (1.01) 0.090 (2.28) 1 260°C for 10 Secs. Max. 2 4 90 Secs. Max. NOTE: Reflow Profile with 240°C peak also acceptable. 0.280 (7.11) 0.070 (1.77) 3 0.200 (5.08) 0.200 (5.08) Pad 1 2 3 4 Connection Volt Cntrl. GND OUT Vdd TAPE AND REEL Denotes Pin 1 Ø 0.059 TYP 0.157±0.004 Ø (1.50) TYP (4.00±0.10) 0.945 +0.012 ) -0.004 0.575 (14.60±0.10) (24.00 +0.3 -0.1 ) DIRECTION OF FEED 0.472±0.004 (12.00±0.10) Mechanical: Shock: Solderability: Vibration: Solvent Resistance: Resistance to Soldering Heat: Environmental: Thermal Shock: Moisture Resistance: CRYSTEK CORPORATION 0.374 0.209 (9.50±0.10) (5.30) Drawing not to scale. Specifications subject to change without notice. Pocket Depth = MIL-STD-883, Method 2002, Condition B MIL-STD-883, Method 2003 MIL-STD-883, Method 2007, Condition A MIL-STD-202, Method 215 MIL-STD-202, Method 210, Condition I or J MIL-STD-883, Method 1011, Condition A MIL-STD-883, Method 1004 Rev: R Date: 25-Jun-2015 Page 3 of 3 12730 Commonwealth Drive • Fort Myers, Florida 33913 Phone: 239-561-3311 • 800-237-3061 Fax: 239-561-1025 • www.crystek.com