Velociti® Series MMO-6SF Description Multi-MOD Six Signal Output Module The Gamewell-FCI Velociti® Series, multi-mod six signal output module (MMO-6SF) provides six (6), Style Y (Class B) or three (3), Style Z (Class A) supervised control circuits suitable for a wide range of signaling applications. Each supervised circuit may be used as a: • Audio speaker circuit. • Notification applicance circuit. • Supervised control output. The Velociti® Series use a communication protocol that substantially increases the speed of communication between the sensors and certain Gamewell-FCI analog addressable fire alarm controls. These devices operate in a grouped fashion. If one of the devices in the group has a status change, the panel’s microprocessor stops the group poll and concentrates on the single device. The net effect is response speed up to five times greater than earlier designs. The MMO-6SF connects to the signaling line circuits (SLC) of the Gamewell-FCI analog addressable series fire alarm control panels. Each of the MMO-6SF supervised control circuits occupies its own address on the system’s SLC allowing each to be fully programmable in its control-byevent sequence of operation. The address of the first supervised output circuit is set with a pair of rotary dials. Each remaining circuit is automatically assigned to its own subsequent address. The MMO6SF module includes an address disable jumper matrix that allows one, two, or three addresses to be turned off to free these addresses for other purposes. An additional jumper setting selects either Style Y or Style Z circuit configurations. A wide range of configurations are possible including 30 VDC, audio input at 25 or 70.7 VRMS, 125 VAC, etc. More than one circuit can share a power supply if the current capacity does not exceed the power supply’s output. Each output circuit on the MMO-6SF monitors its own connection to its power supply and will indicate a fault condition by address if the power source should fail. The MMO6SF is also provided with short circuit monitoring to protect the external power source from short circuits on the notification appliance circuit wiring. This feature can be disabled per individual circuit if the application requires. Features • Each MMO-6SF module provides six (6), Style Y (Class B) or three (3), Style Z (Class A) individually addressable, individually programmable notification appliance or supervised output circuits • Removable wiring terminal blocks allow ease of installation and servicing • Terminal blocks can accommodate 12 to 18 AWG wire • Flexible jumper configuration feature allowing up to three (3), output circuit addresses to be disabled • Accommodates multiple external power inputs • External power monitoring • Short circuit protection of external power supplies • Sources providing AC, DC, or audio inputs • Designed for use with Gamewell-FCI analog addressable series fire alarm control panels • Individual LED indicators* • Ideal for retrofit applications • Two (2), mounting cabinets available for two (2), (MBB2 cabinet) to six (6), (MBB-6 cabinet) units Note: *Only the red LED is operative in panels that do not operate in Velociti® mode. SIGNALING FM APPROVED MEA Approved S1913 3023594 219-02-E Vol. VI 7300-1703:0124 Velociti® and E3 Series® are registered trademarks of Honeywell International Inc. GAMEWELL-FCI 12 Clintonville Road, Northford, CT 06472-1653 USA • Tel: (203) 484-7161 • Fax: (203) 484-7118 Specifications are for information only, are not intended for installation purposes, and are subject to change without notice. No responsibility is assumed by Gamewell-FCI for their use. www.gamewell-fci.com 9020-0634 Rev. D page 1 of 2 ©2013 Honeywell International Inc. All rights reserved. Description (Continued) Contact Ratings (Note: power supply monitoring must also be disabled in such cases.) Current Rating 3A 2A 1A Each circuit has its own status LED that flashes to indicate proper polling and lights steadily when the output has been activated. Two (2), multi-mod series units can be mounted in one MBB-2 cabinet. Additional mounting options include the MCH-6 chassis that can accommodate six multi-mod series modules. The MCH-6 chassis can be installed in a custom cabinet or can be mounted in the MBB-6 cabinet allowing up to six (6), multi-mod series modules in one cabinet. The MMO-6SF is ideal for applications where centralized location of circuits is required. As many as thirty-six (36), supervised output circuits may be located in a cabinet that is only 12.63” H x 24” W x 6.5” D in dimension saving valuable wall space in mechanical rooms and electrical closets and reducing cost of installation. 0.5A 0.9A 0.9A 0.7A 0.5A Maximum Voltage 30 VDC 30 VDC 30 VDC Load Description Resistive Resistive Inductive (L/R= 2ms) 30 VDC Inductive (L/R= 5ms) 110 VDC Resistive 125 VAC Resistive 70.7 & VAC Inductive (PF= 0.35) 125 VAC Inductive (PF= 0.35) MBB-2 MBB-6 External Supply Voltage DC Voltage: Ripple Voltage: Current: Coded Non-coded Non-coded Non-coded Non-coded Ordering Information Part Number Description MMO-6SF MBB-2 MBB-6 MCH-6 Multi-Mod 6 zone interface module Backbox, 2 unit Backbox, 6 unit, requires MCH-6 6-Unit mounting chassis Specifications Operating Voltage: Stand-by Current: Alarm Current: Maximum IDC Wire Resistance: Temperature Range: Humidity Dimensions: Application Non-coded Coded Coded 15-32 VDC 2.25 mA 40 mA (with all six LEDs lit) 25 Ohms 32° F to 120° F (0° to 49° C) 10 to 85% (non-condensing) 6.8” H x 5.8” W x 1.25” D (17.3 x 14.7 x 3.2 cm) 12.25” H x 9.25” W x 3.32” D (31.1 x 23.5 x 8.4 cm) 12.63” H x 24” W x 6.5” D (32 x 60.1 x 16.5 cm) 18-28 Volts, Class 2 Power-Limited 0.1 Volts rms maximum 90 mA per module GAMEWELL-FCI 12 Clintonville Road, Northford, CT 06472-1653 USA • Tel: (203) 484-7161 • Fax: (203) 484-7118 9020-0634 Rev. D page 2 of 2 www.gamewell-fci.com