CRA06P www.vishay.com Vishay Thick Film Chip Resistor Array FEATURES • • • • • Concave terminal array with square corners 4 and 8 terminal package with isolated resistors Wide ohmic range: 10R to 1M0 Lead (Pb)-free solder contacts on Ni barrier layer Pure tin plating provides compatibility with lead (Pb)-free and lead containing soldering processes • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 CRA06P thick film resistor array is constructed on a high grade ceramic body with concave terminations. A small package enables the design of high density circuits. The single component reduces board space, component counts and assembly costs. STANDARD ELECTRICAL SPECIFICATIONS MODEL CIRCUIT CRA06P 03 POWER RATING P70 °C W LIMITING ELEMENT VOLTAGE MAX. V TEMPERATURE COEFFICIENT ± ppm/K TOLERANCE ±% RESISTANCE RANGE E-SERIES 0.063 50 100 200 1 2; 5 10 to 1M 24 + 96 24 Zero-Ohm-Resistor: Rmax. = 50 m, Imax. = 1 A TECHNICAL SPECIFICATIONS PARAMETER CRA06P 03 CIRCUIT UNIT Rated dissipation at 70 °C (2) W per element 0.063 Limiting element voltage (1) V 50 Insulation voltage (1 min) VDC/AC peak 100 Category temperature range °C - 55 to + 155 Insulation resistance > 109 Notes (1) Rated voltage: P x R . (2) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded. PART NUMBER AND PRODUCT DESCRIPTION Part Number: CRA06P08347K0JTA (3) C R A 0 MODEL TERMINAL STYLE CRA06 P 6 P 0 8 3 4 7 K 0 J T A PIN CIRCUIT VALUE TOLERANCE PACKAGING (4) SPECIAL 04 08 3 = 03 R = Decimal K = Thousand M = Million 0000 = 0 Jumper F=±1% G=±2% J=±5% Z = 0 Jumper TA TC Up to 2 digits Product Description: CRA06P 08 03 473 J RT1 e3 CRA06P 08 03 473 J RT1 e3 MODEL TERMINAL COUNT CIRCUIT TYPE RESISTANCE VALUE TOLERANCE PACKAGING (4) LEAD (Pb)-FREE CRA06P 04 08 03 473 = 47 k 4702 = 47 k 10R0 = 10 100 = 10 000 = 0 Jumper F=±1% G=±2% J=±5% Z = 0 Jumper RT1 RT6 e3 = Pure tin termination finish First two digits (3 for 1 %) are significant. Last digit is the multiplier. Notes Preferred way for ordering products is by use of the PART NUMBER. Please refer to the table PACKAGING, see next page. (3) (4) Revision: 24-Jun-13 Document Number: 31047 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 CRA06P www.vishay.com Vishay PACKAGING PACKAGING CODE MODEL TAPE WIDTH CRA06P DIAMETER PITCH PIECES/REEL PAPER TAPE PART NUMBER PRODUCT DESCRIPTION 180 mm/7" 4 mm 5000 TA RT1 330 mm/13" 4 mm 20 000 TC RT6 8 mm DERATING Rated Power in % CIRCUIT 03 CIRCUIT 120 100 80 60 40 20 0 - 55 8 pin 4 pin - 25 0 25 50 75 70 100 125 155 175 Ambient Temperature in °C DIMENSIONS PIN NO# C A w A B C P T W 4 1.60 0.30 0.40 0.40 0.80 0.60 1.60 8 3.20 0.30 0.40 0.40 0.80 0.60 1.60 Tol. P B L DIMENSIONS in millimeters L ± 0.20 ± 0.20 ± 0.15 ± 0.20 - ± 0.10 ± 0.15 T SOLDER PAD DIMENSIONS in millimeters c w WAVE c w p a b 0.8 2.6 0.8 0.4 0.9 b p Revision: 24-Jun-13 a Document Number: 31047 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 CRA06P www.vishay.com Vishay TEST PROCEDURES AND REQUIREMENTS EN 60115-1 TEST (clause) REQUIREMENTS PERMISSIBLE CHANGE (R/R) (1) CONDITIONS OF TEST Stability for product types: CRA06P Resistance (4.5) 10 to 1 M 10 to 1 M - ±1% ± 2 %; ± 5 % ± 100 ppm/K ± 200 ppm/K U = 2.5 x (P70 x R)1/2 2 x Umax.; 0.5 s ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 ) Aging 4 h at 155 °C, dryheat Solder bath method; 235 °C; 2 s Visual examination Solderability (4.17.5) (2) STABILITY CLASS 2 OR BETTER (20/- 55/20) °C and (20/125/20) °C Temperature coefficient (4.8.4.2) Overload (4.13) STABILITY CLASS 1 OR BETTER Good tinning ( 95 % covered) no visible damage Resistance to soldering heat (4.18.2) Solder bath method; (260 ± 5) °C; (10 ± 1) s ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 ) Rapid change of temperature (4.19) 30 min at LCT = - 55 °C; 30 min at UCT = 125 °C; 5 cycles ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 ) (40 ± 2) °C; 56 days; (93 ± 3) % RH ± (1 % R + 0.05 ) ± (2 % R + 0.1 ) 16 h at UCT = 125 °C; 1 cycle at 55 °C; 2 h at LCT = - 55 °C; 1 h/1 kPa at 15 °C to 35 °C; 5 cycles at 55 °C U = (P70 x R)1/2 U = Umax.; whichever is less severe ± (1 % R + 0.05 ) ± (2 % R + 0.1 ) U = (P70 x R)1/2 U = Umax.; whichever is less severe 1.5 h “ON”; 0.5 h “OFF”; 70 °C; 1000 h ± (1 % R + 0.05 ) ± (2 % R + 0.1 ) Duration extended to 8000 h ± (2 % R + 0.1 ) ± (4 % R + 0.1 ) UCT = 125 °C; 1000 h ± (1 % R + 0.05 ) ± (2 % R + 0.1 ) Damp heat, steady state (4.24) Climatic sequence (4.23) Endurance at 70 °C (4.25.1) Extended endurance (4.25.1.8) Endurance at upper category temperature (4.25.3) Notes (1) Figures are given for a single element. (2) Solderability is specified for 2 years after production or requalification. Permitted storage time is 20 years. APPLICABLE SPECIFICATIONS • EN 60115-1 Generic specification • EN 140400 Sectional specification • EN 140401-802 Detail specification • IEC 60068-2-X Variety of environmental test procedures • EIA 481 Packaging of SMD components Revision: 24-Jun-13 Document Number: 31047 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000