Series CH2 www.vishay.com Vishay Wet Tantalum Capacitor, Button, All-Tantalum Case, - 55 °C to + 150 °C Operation FEATURES • All-Tantalum electrodes eliminate silver migration • Withstands high ripple current • Long life reliability • Reverse voltage capability • Mounting: Through-hole PERFORMANCE CHARACTERISTICS Operating Temperature: - 55 °C to + 150 °C INTRODUCTION This conveniently-packaged polar button unit employs a non-solid electrolyte, and has a sintered tantalum anode. The anode is produced from a medium capacitance powder and the lower CV product allows a tighter specification of capacitance stability, dissipation factor and leakage current. The cathode is also of tantalum, and overcomes the restrictions of a silver cathode system in allowing a high ripple current rating and application of a 3 V reverse potential. Both anode and cathode consists of sintered compacts of high purity tantalum powder. The dielectric layer of tantalum pentoxid electrolytically formed on each compact is completely stable. The system is enclosed between a tantalum plate and a tantalum cup, with an outer nickel case. The seal is a highly efficient system comprising a PTFE gasket clamped between coined plates of tantalum by a work-hardened nickel ring. This type of seal, common to all button styles, is largely responsible for their long life and high reliability under severe military environments. The combination of the tantalum pentoxide dielectric stability and the extremely efficient seal has been shown to ensure that there is no significant difference in electrical parameters or instant use behaviour after 10 years storage or longer. A shelf life in excess of 20 years is confidently expected. There are four types of terminations and mounting options are available. These include a treated stud or bolt, PCB pins, a tab for panels, and ribbons leads slotted through-holes. These are illustrated in the photograph, and dimensional table drawing. APPLICATIONS The CH2 series is designed for use in general military and professional applications. For example: Power supply “smoothing”, filter networks, switching, by-pass, timer functions, and where reverse potential occur. Voltage Range: 3 VDC to 75 VDC Capacitance Range: 33 μF to 470 μF SPECIFICATIONS Environmental classification: 55/150/56 Vibration: 10 Hz to 2000 Hz, 0.75 mm or 98 m/s2, 150 h Bump: 390 m/s2, 4000 bumps Shock: 981 m/s2 Acceleration: 981 m/s2 Low air pressure: 1 kPa REVERSE VOLTAGE CAPABILITY The CH2 series employ tantalum cathodes which allow the continuous application of reverse potentials not exceeding 3 V over the whole temperature range. SURGE VOLTAGE The surge voltage capability is 115 % of the voltage rating at the relevant temperature. TEMPERATURE RANGE The capacitor is designed for operation between - 55 °C and + 150 °C, with linear voltage derating above + 85 °C to 66 % of the rated voltage at + 150 °C. CAPACITANCE TOLERANCE The standard capacitance tolerance is ± 20 % although special tolerances are available by arrangement. RIPPLE CURRENT CAPABILITY The maximum allowable ripple current is 750 mARMS. This value applies under normal cooling conditions and is irrespective of frequency or waveform. The algebraic sum of the AC peak and DC voltages must not exceed the forward or reverse voltage ratings at the relevant temperature. WEIGHT The CH2 style with a stud termination weighs approximately 18.1 g, including the nut. The CH2 styles, which has a printed circuit board mounting, weighs approximately 17.3 g. Revision: 04-Nov-11 Document Number: 42098 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Series CH2 www.vishay.com Vishay APPLICATION INFORMATION RELIABILITY Capacitors may be operated at less than the rated voltage, resulting in significantly reduced leakage current values. All capacitors are subjected to burn-in. This is to remove infant mortalities and ensure reliability. The capacitor lifetime is enhanced when the unit is subjected to a reduced ripple current, a low ambient temperature, and is externally cooled. The use of a heat sink is recommended. In timing circuits, or other applications where the device is subjected only to a DC voltage, the ballistic or DC capacitance will be somewhat larger than measured at 50 Hz. The parametric information must necessarily be brief, although additional comprehensive data is available on request, and the tests tailored to customers’ requirements can be made. ORDERING PROCEDURE Example: CH2C (220 μF, 15 VDC) Vishay Part Number: CH2C227M015A ORDERING INFORMATION CH2 C 227 M 100 A MODEL CASE CODE CAPACITANCE TOLERANCE VOLTAGE TERMINATION AND PACKAGING - See Ratings and Case Codes Table This is expressed in picofarads. The first two digits are the significant figures. The third is the number of zeros to follow M = 20 % (std) K = 10 % (special order) This is expressed in volts. To complete the three-digit block, zeros precede the voltage rating. A decimal point is indicated by an “R” (6R3 = 6.3 V) A = Stud B = PC mount pins C = Twin tag or ribbon D = Panel or potting tag Blank = Standard (tin/lead coating) DIMENSIONS in millimeters The CH2 series is comprised of two case sizes, differing in depth of cup only. The case size dimensions are shown in the table. Four mounting styles are available in both case sizes. Stud C D B PC Pins + Potting Tag Twin Tag or Ribbons + + + A J E N Hole Q dia. G - H Mounting holes M dia. F 20 S.W.G. H.T.D. Nickel 4 BA shakeproof nut P This mounting style is suitable for panel thickness of up to 1.2 mm L crs. R - S Hole T dia. W U crs. Mounting holes V dia. K crs. A 3.6 B C D 6.7 (1) 21.8 8.4 (2) E F G H J K crs. L crs. M N dia. nom. 8.4 16.2 8.4 1.8 0.8 20.3 10.2 1.1 2.4 P Q dia. R S T dia. U crs. V W dia. nom. 13.1 1.0 7.5 10.7 1.6 13.0 3.5 0.30 Notes (1) All dimensions are in mm, and are maximum unless otherwise stated (2) For C case size, case height is 8.5 mm (3) Width of anode tag 4.22 mm max. Revision: 04-Nov-11 Document Number: 42098 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Series CH2 www.vishay.com Vishay STANDARD RATINGS VISHAY CASE PART NUMBERS CODE CAPACITANCE AT 50 Hz (μF) C DISSIPATION FACTOR MAX. ESR MAX. ESR MAX. DC MAX. DC AT 50 Hz AT 50 Hz AT 20 °C AT - 55 °C AT 20 °C AT 150 °C (%) (%) 100 kHz 100 kHz (μA) (μA) () () 20 °C 125 °C - 55 °C 150 °C 3 VDC AT 150 °C CH2B337(1)003(2) CH2C477(1)003(2) B C 330 470 15.0 20.0 CH2B227(1)006(2) CH2C337(1)006(2) B C 220 330 12.5 15.0 CH2B157(1)015(2) CH2C227(1)015(2) B C 150 220 10.0 12.5 CH2B107(1)025(2) CH2C157(1)025(2) B C 100 150 6.0 9.0 CH2B686(1)035(2) CH2C107(1)035(2) B C 68 100 5.0 7.5 CH2B476(1)050(2) CH2C686(1)050(2) B C 47 68 4.0 6.0 CH2B336(1)075(2) CH2C476(1)075(2) B C 33 47 2.0 2.5 18.0 23.0 1.0 1.0 5.0 5.0 2.0 2.0 100 100 - 40.0 - 50.0 30.0 40.0 5.0 5.0 2.0 2.0 100 100 - 35.0 - 35.0 25.0 25.0 5.0 5.0 2.0 2.0 100 100 - 30.0 - 30.0 20.0 20.0 5.0 5.0 2.0 2.0 100 100 - 20.0 - 20.0 15.0 15.0 5.0 5.0 2.0 2.0 100 100 - 15.0 - 15.0 12.5 12.5 5.0 5.0 2.0 2.0 100 100 - 10.0 - 10.0 10.0 10.0 5.0 5.0 2.0 2.0 100 100 - 5.0 - 5.0 7.5 7.5 6 VDC AT 150 °C 15.0 18.0 1.0 1.0 15 VDC AT 150 °C 12.0 15.0 1.0 1.0 25 VDC AT 150 °C 7.5 11.0 1.0 1.0 35 VDC AT 150 °C 6.5 9.0 1.0 1.0 50 VDC AT 150 °C 5.0 7.5 1.0 1.0 75 VDC AT 150 °C 3.0 3.5 1.0 1.0 Note • Part number definitions: (1) Capacitance tolerance: M = 20 % standard K = 10 % special order (2) Termination type: A = Stud or bolt B = Pins for PCB C = Twin tags or ribbons D = Potting tag PERFORMANCE CURVES Capacitance/temperature at 50 Hz Dissipation factor/temperature at 50 Hz 120 70 Percentage of capacitance (%) (25 °C standard) 470 µF, 3 V 110 33 µF, 75 V 90 80 70 Dissipation factor (%) 60 100 60 - 60 470 µF, 3 V 50 40 30 20 10 - 40 - 20 Revision: 04-Nov-11 0 20 40 60 80 100 120 140 (°C) 0 - 60 33 µF, 75 V - 40 - 20 0 20 40 60 80 100 120 140 (°C) Document Number: 42098 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Series CH2 www.vishay.com Vishay PERFORMANCE CURVES Impedance/temperature at 50 Hz Leakage current/temperature at maximum voltage 100 47 µF, 75 V 35 50 Impedance (Ω) 20 Leakage current (µF) 30 150 µF, 15V 10 330 µF, 3 V 5 470 µF, 3 V 1 = 47 µF, 75 V 2 = 150 µF, 15 V 3 = 330 µF, 3 V 4 = 470 µF, 3 V 25 1 20 15 2 10 3 2 5 1 - 60 - 40 - 20 0 - 60 0 20 40 60 80 100 120 140 160 (°C) 4 - 40 - 20 Capacitance/frequency at 25 °C 20 40 60 80 100 120 140 (°C) ESR/frequency at 25 °C 1.2 120 Percentage of 50 Hz capacitance (%) 0 1.0 100 1 0.8 80 60 ESR (Ω) 2 3 4 40 20 1 = 33 µF, 75 V 2 = 47 µF, 75 V 3 = 150 µF, 15 V 4 = 220 µF, 15 V 5 = 330 µF, 3 V 6 = 470 µF, 3 V 0 101 0.6 0.4 47 µF, 75 V 5 6 0.2 470 µF, 3 V 0 102 103 104 (Hz) 101 102 103 104 105 (Hz) 106 Impedance/frequency at 25 °C 100 1 1 = 33 µF, 75 V 2 = 47 µF, 75 V 3 = 330 µF, 3 V 4 = 470 µF, 3 V Impedance (Ω) 2 10 3 4 1 0.1 101 102 103 104 105 (Hz) 106 Note • All performance curves are provided from historic Arcotronics style AHS datasheet information Revision: 04-Nov-11 Document Number: 42098 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Series CH2 www.vishay.com Vishay CROSS REFERENCE VISHAY PART NUMBER CH2C476M075A CH2B336M075A CH2C686M050A CH2B476M050A CH2C107M035A CH2B686M035A CH2C157M025A CH2B107M025A CH2C227M015A CH2B157M015A CH2C337M006A CH2B227M006A CH2C477M003A CH2B337M003A CH2C476M075B CH2B336M075B CH2C686M050B CH2B476M050B CH2C107M035B CH2B686M035B CH2C157M025B CH2B107M025B CH2C227M015B CH2B157M015B CH2C337M006B CH2B227M006B CH2C477M003B CH2B337M003B CH2C476M075D CH2B336M075D CH2C686M050D CH2B476M050D CH2C107M035D CH2B686M035D CH2C157M025D CH2B107M025D CH2C227M015D CH2B157M015D CH2C337M006D CH2B227M006D CH2C477M003D CH2B337M003D CH2C476M075C CH2B336M075C CH2C686M050C CH2B476M050C CH2C107M035C CH2B686M035C CH2C157M025C CH2B107M025C CH2C227M015C CH2B157M015C CH2C337M006C CH2B227M006C CH2C477M003C CH2B337M003C Revision: 04-Nov-11 ARCOTRONICS PART NUMBER 402/1/50028/004 402/1/50027/003 402/1/50028/005 402/1/50027/004 402/1/50028/006 402/1/50027/005 402/1/50028/007 402/1/50027/006 402/1/50028/008 402/1/50027/007 402/1/50028/009 402/1/50027/008 402/1/50028/010 402/1/50027/009 402/1/50148/004 402/1/50147/003 402/1/50148/005 402/1/50147/004 402/1/50148/006 402/1/50147/005 402/1/50148/007 402/1/50147/006 402/1/50148/008 402/1/50147/007 402/1/50148/009 402/1/50147/008 402/1/50148/010 402/1/50147/009 402/1/50030/004 402/1/50029/003 402/1/50030/005 402/1/50029/004 402/1/50030/006 402/1/50029/005 402/1/50030/007 402/1/50029/006 402/1/50030/008 402/1/50029/007 402/1/50030/009 402/1/50029/008 402/1/50030/010 402/1/50029/009 402/1/50032/004 402/1/50031/003 402/1/50032/005 402/1/50031/004 402/1/50032/006 402/1/50031/005 402/1/50032/007 402/1/50031/006 402/1/50032/008 402/1/50031/007 402/1/50032/009 402/1/50031/008 402/1/50032/010 402/1/50031/009 NATO PART NUMBER 5910-99-014-3024 5910-99-014-3023 5910-99-014-3026 5910-99-014-3025 5910-99-014-3028 5910-99-014-3027 5910-99-014-3030 5910-99-014-3029 5910-99-014-3032 5910-99-014-3031 5910-99-014-3034 5910-99-014-3033 5910-99-014-3036 5910-99-014-3035 5910-99-014-3056 5910-99-014-3055 5910-99-014-3058 5910-99-014-3057 5910-99-014-3060 5910-99-014-3059 5910-99-014-3062 5910-99-014-3061 5910-99-014-3064 5910-99-014-3063 5910-99-014-3066 5910-99-014-3065 5910-99-014-3068 5910-99-014-3067 5910-99-014-3088 5910-99-014-3087 5910-99-014-3090 5910-99-014-3089 5910-99-014-3092 5910-99-014-3091 5910-99-014-3094 5910-99-014-3093 5910-99-014-3096 5910-99-014-3095 5910-99-014-3098 5910-99-014-3097 5910-99-014-3100 5910-99-014-3099 5910-99-651-4349 5910-99-651-4348 5910-99-651-4347 5910-99-651-4346 5910-99-651-4345 5910-99-651-4344 5910-99-651-4343 5910-99-651-4342 5910-99-651-4341 5910-99-651-4340 5910-99-651-4339 5910-99-651-4338 5910-99-651-4337 5910-99-651-4336 Document Number: 42098 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000