DIMENSIONS(mm): You must be fully aware of all the distinctive features and precautions related to this camera before installing it. COMPOSITION: 75.7 Guide Pattern 101.0 Service Monitor Cable 47.15 100.0 37.0 L-Wrench Operation Manual Mounting Screw HD51 Series 142.4 ※ 3/4 JIS B0202-1982 INSTALLATION: Guide Pattern Put the dome cover over the base. 7 Fix the dome cover on the base by L-Wrench. Dome Cover Weight PRECAUTIONS: ! Design and specifications are subject to change without notice. NAME AND FUNCTION: le to ins t READ AND KEEP THIS OPERATION MANUAL a 4 5 a DC Level Adjustment V.R 3 2 H /A EAT UD ER IO AC 24V J503 BLC ON AGC OFF FL ON b Note When this camera is installed near wireless communication devices that emits strong electromagnetic field, irregularity such as noise on the monitor may appear. Tilt rotation: Adjusting the vertical angle. 4 Focus handle: Focus (Far or Near) 2 Pan rotation: Adjusting the horizontal angle. 5 Zoom handle: Zoom (Tele or Wide) 3 Horizontal rotation: Adjusting the horizontal position of the screen. Camera Lay-out • The wire is polarized. • Use 12VDC #1 Connecting to Monitor and Power 12VDC Power Type 1 Video (Yellow) Video Output No. GND #2 Power - 12VDC (Red) power source. Function Terminal Color Remark #1 Video Output Yellow 1.0 Vp-p #2 Power Input Red 12VDC, Max 3W/ 250mA J504 AC24V b Function Selection Switch: •FL(Flickerless) ON/OFF •AGC(Auto Gain Control) ON/OFF •BLC(Back Light Compensation) ON/OFF c Service Monitor Connecter: Use service monitor connector to set camera angle & focus when installing. a 05 Do not drop the camera or subject them to physical shocks. 360º 1 Do not disassemble the camera. CONNECTION: 360º Vari-focal Lens Type It can cause malfunctions to occur. ! 90º CAMERA SET-UP: There are no user-serviceable parts inside it. ! mp Built-in 3-axis camera bracket makes it much easier to rotate in any direction. Vari-focal Lens Type Do not install the camera in extreme temperature conditions. Do use the camera under conditions where temperatures are within -20°C to 45°C. Be especially careful with ventilation under high temperatures. ! Need Help? Call 1.800.796.CCTV for sales, service and customer support. www.honeywellvideo.com L-Wrench Si J502 6 Mounting Screw J501 Adjust desired focus and scene by turning and moving the 3-axis camera bracket by hand. VIDEO 5 SWITCH Fix the camera to a celling using four screws. • 1/3" Sony Super HAD CCD • High Resolution:550 TV Lines • 4 - 9mm DC Vari-focal Auto Iris • Auto White Balance • AGC, BLC, Flickerless On/Off • Extra Video Output for Installer • 3-Axis Camera Construction • Vandal-Resistant Dome Housing • Diameter of Bubble:100mm 1 2 3 4 Dome Base 2 : 1 Interlace 15.734kHz 15.625kHz 59.94Hz 50Hz 1/3" SONY Super HAD CCD 410K / 380K 470K / 440K More than 50dB (AGC Off) 550 TV Lines 1.0 Vp-p (75 Ohms, composite) Fixed Lens : f=4.0mm Manual Internal 0.3 Lux 1/60 ~ 100,000 Sec. 1 /50 ~ 100,000 Sec. Auto On / Off On / Off (with Slide Switch) On / Off (with Slide Switch) Power, Video 12VDC (10V~15V) / 3W (Max) 100mm Approx. 844g DC LEVEL Draw out power / video wires to the connecting places. PAL PAL : 625 Lines ll 3 Image Sensor Total / Effective Pixels No. S / N Ratio Resolution Video Output Level Lens Focus Sync. System Sensitivity Electronic Shutter White Balance AGC BLC Flickerless Input / Output Connector Power Consumption Dome Size (Ø) NTSC NTSC : 525 Lines ON Drill four holes according to the guide pattern then insert anchors into the drilled holes. Signal System Scanning System Scanning Frequency (H) Scanning Frequency (V) • 2 Model J5 Stick the guide pattern on the wall or ceiling. P/N:3810-0055Q Rev 0 05/23 Ceiling 1 Operation Manual SPECIFICATIONS: c TROUBLESHOOTING: If you have trouble operating your camera, refer to the following. If the guidelines do not enable you to solve the problem, contact an authorized technician. The image does not appear on the screen. Check the power source for the monitor and camera and ensure that the voltage and polarity are properly connected and being supplied correctly. The image on the screen is dim. Check if the lens is stained. If dirty, clean the lens with a soft, clean cloth. Adjust the Back Focus of the lens again. The camera does not work properly, the surface of the camera case is hot, and a black line appears on the screen. Check if you have connected the camera to a proper power source and If there is no problem with the power, turn the unit off immediately and seek assistance from our Customer Service department. The screen blinks a lot. Check if the camera is pointed toward the sun or a fluorescent lamp. Adjust the angle or location of the camera if too much light is coming into the screen.