Designed and Manufactured in Germany Specification Oscillator type: Rev.: 4 Date: 2014-04-26 AXIOM5050 VHF Ultra-Low Phase Noise OCXO in Connectorized Package Parameter Frequency range Standard frequencies Frequency stability Initial tolerance @ +25°C vs. operating temperature range vs. supply voltage variation (pushing) vs. load change (pulling) Long term (aging) per day st Long term (aging) 1 year Frequency adjustment range Electronic Frequency Control (EFC) EFC voltage VC EFC slope (∆f / ∆VC) EFC input impedance RF output Signal waveform Load RL Output level (Note 2) Harmonics Spurious Warm-up time @ +25°C Phase noise @ 100 MHz and 120 MHz Supply voltage VS (Note 3) Current consumption (steady state) Current consumption (warm-up) Enclosure (see drawing) (LxWxH) Weight Packing Notes: 1. 2. 3. min. typ. max. Unit 150 MHz MHz ±300 ppb @ VC = 5.0 V steady state ±10 ±5 ±2 ±200 ppb ppb ppb ppb VS ±5% RL ±5% after 30 days operation after 30 days operation 10.0 ppm V 50 100.000/120.000 Option 2 & 3 See tables 2 & 3 ±1 ±100 ±1 0 ±2 5.0 Positive 100 kΩ Sine wave 50 -30 -90 5 Ω dBm dBc dBc min 12.6 300 500 V mA mA +7 11.4 Condition 3 See table 1 12.0 50.0x50.0x21.0 max. 60 Palette ±5% ∆ffinal/f0 < ±0.1 ppm Option 1 @ +25°C mm g Terminology and test conditions are according to IEC60679-1 and MIL-PRF-55310, unless otherwise stated Other output level on request Other supply voltage on request Absolute Maximum Ratings Parameter min. max. Supply Voltage VS Control Voltage VC Storage Temperature -0.5 -0.5 -55 VS + 10% 15 +125 GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany AXIOM5050 Rev.4 Drawing D0 Page 1(4) Unit Condition V V °C VS to GND VC to GND www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Designed and Manufactured in Germany Phase Noise – Option 1: Offset 10 Hz 100 Hz 1 kHz 10 kHz ≥100 kHz Table 1 A -90 -125 -155 -165 -175 B -95 -130 -158 -168 -175 100 MHz C -97 -132 -160 -170 -175 D -100 -135 -162 -172 -175 E -105 -137 -164 -174 -175 A -85 -118 -148 -160 -175 120 MHz C -95 -125 -153 -168 -175 B -90 -122 -150 -165 -175 D -97 -127 -155 -170 -175 E -100 -130 -157 -172 -175 Unit dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz Other phase noise parameters on request Frequency stability vs. temperature Option 2 05 10 25 50 100 200 Table 2 Stability [ppb] ±5 ±10 ±25 ±50 ±100 ±200 Temperature range [°C] 05 0 ~ +50 O -10 ~ +60 O -20 ~ +70 O -30 ~ +70 O -40 ~ +75 -40 ~ +85 -55 ~ +85 Table 4 “Availability” Lower Temperature Option 3 T [°C] 0 0 1 -10 2 -20 3 -30 4 -40 5 -55 Table 3 10 X X X O O - Upper Temperature Option 3 T [°C] A +50 B +60 C +70 D +75 E +80 F +85 Standard: “1B” = -10°C to +60°C Frequency stability [Option 2] 25 50 100 X X X X X X X X X X X X X X X O X X O X X 200 X X X X X X X X = available, O = available on request, - not available Ordering Code Option 1 Option 2 Option 3 [Phase noise] [Stability] [Temperature range] AXIOM5050 Table 1 Table 2 Table 3 Example: AXIOM5050-C-25-1B_Rev.4 – 100.000 MHz Model GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany AXIOM5050 Rev.4 Drawing D0 Page 2(4) Revision Frequency [MHz] Rev.4 100.000 www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Designed and Manufactured in Germany Enclosure drawing Pin connections: Pin # Symbol 1 VS 2 GND 3 VC SMA RF OUT Function Supply Voltage Ground Control Voltage (EFC) RF Output * See Application Note AXAN-011 GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany AXIOM5050 Rev.4 Drawing D0 Page 3(4) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Designed and Manufactured in Germany Handling and Testing Parameter Procedure Handling and Testing Processing Source Application Note AXAN-011 Application Note AXAN-012 Parameter Procedure Electrostatic discharge (ESD) THD devices SMD devices Washable RoHS- Compliant IEC60749-26 IEC60749-27 Yes Yes www.axtal.com www.axtal.com Condition HBM MM No No 2000 V 200 V Environmental conditions Test Sealing tests (if applicable) Solderability Resistance to soldering heat Shock* IEC 60068 Part … 2-17 IEC 60679-1 Clause 5.6.2 MIL-STD202G Method 112E 2-20 2-58 5.6.3 208H 210F 2-27 5.6.8 213B Vibration, 2-6 5.6.7.1 201A sinusoidal* 204D Vibration, 2-64 5.6.7.3 214A random* Endurance tests 108A - ageing 5.7.1 - extended aging 5.7.2 Other environmental conditions on request MIL-STD810F Method MIL-PRF55310D Clause 3.6.1.2 3.6.52 3.6.48 516.4 3.6.40 516.4-4 3.6.38.1 3.6.38.2 3.6.38.3 3.6.38.4 514.5 4.8.35 Test conditions (IEC) Gross leak: Test Qc, Fine leak: Test Qk Test Ta Method 1 Test Td1 Method 2 Test Td2 Method 2 Test Ea, 3 x per axes 100g, 6 ms half-sine pulse Test Fc, 30 min per axes, 10 Hz - 55 Hz 0,75mm; 55 Hz - 2 kHz, 10g Test Fdb 30 days @ 85°C, OCXO @25°C 1000h, 2000h, 8000h @85°C Data sheet is for information purposes only and may be subject to modifications or may be discontinued without notice. Revision History Rev. Drawing Date [dd.mm.yyyy] 3 4 D0 D0 14.10.2013 26.04.2014 GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany Remarks Major revision Frequency range extended, various parameters updated, environmental conditions updated, editorial changes AXIOM5050 Rev.4 Drawing D0 Page 4(4) Author Checked CG HH BN HH www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected]