AXIOM45ULN

Designed and
Manufactured
in Germany
Specification
Oscillator type:
Rev.: 2
Date: 2015-01-11
AXIOM45ULN
Ultra-Low Noise OCXO in Eurocase package
Parameter
Nominal frequency (Note 2)
Frequency stability
Initial tolerance @ +25°C
vs. operating temperature range
vs. supply voltage variation (pushing)
vs. load change (pulling)
Long term (aging) per day
st
Long term (aging) 1 year
Long term (aging) 15 years
Frequency adjustment range
Electronic Frequency Control (EFC)
EFC voltage VC
EFC slope
EFC non-linearity
EFC input impedance
Modulation bandwidth
RF output
Signal waveform
Load RL
Output level
Harmonics
Spurious
Warm-up time @ +25°C
Phase noise
Short term stability (Allan deviation)
Oven alarm output
Oscillator enable input
(Note 3)
Reference voltage VREF output
Supply voltage VS
Current consumption (steady state)
Current consumption (warm-up)
Operating temperature range
Marking
Enclosure (see drawing) (LxWxH)
Weight
Packing
Notes:
1.
2.
3.
min.
typ.
max.
10.000
±0.5
0
±1.0
VREF/2
Positive
Condition
MHz
±100
±5
±0.5
±0.5
±0.5
±30
±500
ppb
ppb
ppb
ppb
ppb
ppb
ppb
±1.5
VREF
ppm
V
10
%
kΩ
kHz
100
1
Sine wave
50
+5
Unit
+10
-20
-90
5
Ω
dBm
dBc
dBc
min
See table 1
-12
5·10
-11
1·10
-11
-10
1·10
1·10
LOW = alarm (not stable)
HIGH = ready
LOW = Oscillator OFF
HIGH = Oscillator ON
5.0
10.5
12.0
12.6
200
340
-20
+75
AXTAL Logo
AXIOM45ULN
10.000MHz
S/N wwyy
36.1x27.1x14.0 max.
30
Palette
VC @ VREF/2
steady state
VS ±100 mV
RL ±5 %
after 10 days operation
after 10 days operation
after 10 days operation
@ -3 dB
±5 %
@ 9 ~ 11 MHz
∆ffinal/fnominal < ±100 ppb
Option 1
τ=1s
τ = 10 s
τ = 100 s
0 … 0.4 V
2.4 … 5 V
0 … 0.4 V
2.4 … 12.6 V
V
V
@ +25°C
mA
°C
mm
g
ww = week, yy = year
Similar to CO 08
Terminology and test conditions are according to IEC60679-1 and MIL-PRF-55310, unless otherwise stated
Other frequencies on request
HCMOS compatible input
GmbH & Co. KG
Roemerring 9
D-74821 Mosbach
Germany
AXIOM45ULN Rev.2
Drawing D0
Page 1(4)
www.axtal.com
fon: +49 (6261) 939834
fax: +49 (6261) 939836
E-mail: [email protected]
Designed and
Manufactured
in Germany
Absolute Maximum Ratings
Parameter
min.
max.
Unit
Condition
Supply Voltage VS
Control Voltage VC
Oscillator Enable Voltage VOE
Storage Temperature
Resistance to Soldering Heat
-0.5
-0.5
-0.5
-55
VS + 10%
15
VS
+125
10
V
V
V
°C
sec
VS to GND
VC to GND
VOE to GND
@ +245°C
Phase Noise – Option 1:
Offset
A
-110
-142
-155
-160
-165
1 Hz
10 Hz
100 Hz
1 kHz
≥10 kHz
Table 1
Option
B
-112
-144
-156
-160
-165
C
-115
-146
-157
-160
-165
Unit
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
Ordering Code
Option 1
Revision Frequency [MHz]
[Phase noise]
AXIOM45ULN
Table 1
Rev.2
10.000
Example: AXIOM45ULN-A_Rev.2 – 10.000 MHz
Model
Handling and Testing
Parameter
Handling and Testing
Processing
Parameter
Electrostatic discharge (ESD)
THD devices
SMD devices
Washable
RoHS- Compliant
GmbH & Co. KG
Roemerring 9
D-74821 Mosbach
Germany
Procedure
Application Note AXAN-011
Application Note AXAN-012
Procedure
IEC60749-26
IEC60749-27
Yes
Yes
AXIOM45ULN Rev.2
Drawing D0
Page 2(4)
HBM
MM
No
No
Source
www.axtal.com
www.axtal.com
Condition
2000 V
200 V
www.axtal.com
fon: +49 (6261) 939834
fax: +49 (6261) 939836
E-mail: [email protected]
Designed and
Manufactured
in Germany
Enclosure drawing:
Pin connections
Pin #
1
2
3
4
5
6
7
GmbH & Co. KG
Roemerring 9
D-74821 Mosbach
Germany
AXIOM45ULN Rev.2
Drawing D0
Page 3(4)
Symbol
VC
OE
VREF
VS
RF OUT
OA
GND
Function
Control Voltage (EFC)
Oscillator Enable Input
Reference Voltage
Supply Voltage
RF Output
Oven Alarm Output
Ground
www.axtal.com
fon: +49 (6261) 939834
fax: +49 (6261) 939836
E-mail: [email protected]
Designed and
Manufactured
in Germany
Environmental conditions
Test
Sealing tests
(if applicable)
Solderability
Resistance to
soldering heat
Shock*
IEC
60068
Part …
2-17
IEC
60679-1
Clause
5.6.2
MIL-STD202G
Method
112E
2-20
2-58
5.6.3
208H
210F
2-27
5.6.8
213B
Vibration,
2-6
5.6.7.1
201A
sinusoidal*
204D
Vibration,
2-64
5.6.7.3
214A
random*
Endurance tests
108A
- ageing
5.7.1
- extended aging
5.7.2
Other environmental conditions on request
MIL-STD810F
Method
MIL-PRF55310D
Clause
3.6.1.2
3.6.52
3.6.48
516.4
3.6.40
516.4-4
3.6.38.1
3.6.38.2
3.6.38.3
3.6.38.4
514.5
4.8.35
Test conditions (IEC)
Gross leak: Test Qc,
Fine leak: Test Qk
Test Ta Method 1
Test Td1 Method 2
Test Td2 Method 2
Test Ea, 3 x per axes 100g,
6 ms half-sine pulse
Test Fc, 30 min per axes,
10 Hz - 55 Hz 0,75mm; 55 Hz - 2 kHz, 10g
Test Fdb
30 days @ 85°C, OCXO @25°C
1000h, 2000h, 8000h @85°C
Data sheet is for information purposes only and may be subject to modifications or may be discontinued without notice.
Revision History
Rev.
Drawing
Date
[dd.mm.yyyy]
1
1
2
D0
D1
D0
04.02.2015
07.04.2015
11.01.2016
GmbH & Co. KG
Roemerring 9
D-74821 Mosbach
Germany
Remarks
Author
Checked
First issue
Title corrected
Phase noise options added
HH
HH
HH
HH
HH
HH
AXIOM45ULN Rev.2
Drawing D0
Page 4(4)
www.axtal.com
fon: +49 (6261) 939834
fax: +49 (6261) 939836
E-mail: [email protected]