Designed and Manufactured in Germany Specification Oscillator type: Rev.: 3 Date: 2014-04-05 AXIS10LN Low Phase Noise SMD VCXO with HCMOS Output Parameter Frequency range Frequency stability Initial tolerance vs. operating temperature range vs. supply voltage variation vs. load change st Long term (aging) 1 year Long term (aging) following years Frequency adjustment range Electronic Frequency Control (EFC) EFC voltage VC EFC slope (∆f / ∆VC) EFC non-linearity EFC input impedance RF output Signal waveform Load Rise & decay time Symmetry (duty cycle) Sub-harmonics Phase noise @ 100 MHz (Note 2) Phase noise floor Supply voltage VS min. typ. Notes: 1. 2. 3. 4. Unit Condition 165 MHz ppm ppm ppm Option 2 & 3 ±3 ±3 ±3 ±1 ppm ppm ppm ppm VS ±5% Load ±5% @ 40°C @ 40°C 3.15 4.75 ppm ppm ppm V V 50 MHz ~ 90 MHz 90 MHz ~ 120 MHz 120 MHz ~ 165 MHz Option 1 = “33” Option 1 = “50“ 10 ±5 ±5 to ±20 See tables 1 & 2 ±40 ±25 ±15 0.15 0.25 Positive ±5 ±10 100 HCMOS 15 5 60 40 3.15 4.75 None -95 -125 -150 -155 -160 -160 3.3 5.0 Current consumption (Note 3) Enclosure (see drawing) Weight Packing max. -155 3.45 5.25 50 30 14.4x9.5x6.0 max. 2 Tape & Reel % kΩ pF ns % @ VS/2 dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz V V mA mA 10 Hz 100 Hz 1 kHz 10 kHz ≥100 kHz @ ≥ 10 kHz Option 1 = “33” Option 1 = “50“ Option 1 = “33“ Option 1 = “50” mm g IEC 61837 CO 27 IEC 60286-3 Terminology and test conditions are according to IEC60679-1 and MIL-PRF-55310, unless otherwise stated Phase noise for other frequencies on request Current consumption depends of frequency All combinations of options might not be available. Please consult factory GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany AXIS10LN Rev.3 Drawing D0 Page 1(4) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Designed and Manufactured in Germany Absolute Maximum Ratings Parameter min. max. Supply Voltage VS Control Voltage VC Storage Temperature -0.5 -0.5 -55 VS + 10% 15 +125 Unit Condition V V °C VS to GND VC to GND Frequency stability vs. temperature Option 2 5 10 15 20 Stability [ppm] ±5 ±10 ±15 ±20 Table 1 Lower Temperature Option 3 T [°C] 0 0 1 -10 2 -20 3 -30 4 -40 Upper Temperature Option 3 T [°C] A +50 B +60 C +70 D +75 E +80 F +85 Table 2 Ordering Code Option 1 Option 2 Option 3 [Supply Voltage] [Stability] [Temperature range] AXIS10LN 33 or 50 Table 1 Table 2 Example: AXIS10LN-50-10-2C_Rev.3 – 100.000 MHz Model Revision Frequency [MHz] Rev.3 100.000 Handling and Testing Parameter Procedure Handling and Testing Processing Parameter Application Note AXAN-011 Application Note AXAN-012 Procedure Electrostatic discharge (ESD) THD devices SMD devices Washable RoHS compliant GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany IEC60749-26 IEC60749-27 Yes Yes AXIS10LN Rev.3 Drawing D0 Page 2(4) HBM MM No No Source www.axtal.com www.axtal.com Condition 2000 V 200 V www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Designed and Manufactured in Germany Enclosure drawing Pin connections Pin # 1 2 3 4 5 6 Symbol VC N.C. GND RF OUT N.C. Vs Function Control Voltage (EFC) No Connection Ground RF Output No Connection Supply Voltage Environmental conditions Test Sealing tests (if applicable) Solderability Resistance to soldering heat Shock* IEC 60068 Part … 2-17 IEC 60679-1 Clause 5.6.2 MIL-STD202G Method 112E 2-20 2-58 5.6.3 208H 210F 2-27 5.6.8 213B Vibration, 2-6 5.6.7.1 201A sinusoidal* 204D Vibration, 2-64 5.6.7.3 214A random* Endurance tests 108A - ageing 5.7.1 - extended aging 5.7.2 Other environmental conditions on request MIL-STD810F Method MIL-PRF55310D Clause 3.6.1.2 3.6.52 3.6.48 516.4 3.6.40 516.4-4 3.6.38.1 3.6.38.2 3.6.38.3 3.6.38.4 514.5 4.8.35 Test conditions (IEC) Gross leak: Test Qc, Fine leak: Test Qk Test Ta Method 1 Test Td1 Method 2 Test Td2 Method 2 Test Ea, 3 x per axes 100g, 6 ms half-sine pulse Test Fc, 30 min per axes, 10 Hz - 55 Hz 0,75mm; 55 Hz - 2 kHz, 10g Test Fdb 30 days @ 85°C, OCXO @25°C 1000h, 2000h, 8000h @85°C Data sheet is for information purposes only and may be subject to modifications or may be discontinued without notice. GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany AXIS10LN Rev.3 Drawing D0 Page 3(4) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Designed and Manufactured in Germany Revision History Rev. Drawing Date [dd.mm.yyyy] 2 3 D1 D0 01.10.2012 05.04.2014 GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany Remarks Editorial changes Major specification update AXIS10LN Rev.3 Drawing D0 Page 4(4) Author Checked BN HH BN HH www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected]