Specification AXIOM55 Oscillator type: Low Phase Noise VHF

Designed and
Manufactured
in Germany
Specification
Oscillator type:
Rev.: 4
Date: 2014-04-18
AXIOM55
Low Phase Noise VHF OCXO with Sine Wave Output
Parameter
Frequency range
Standard frequencies
min.
Enclosure (see drawing) (LxWxH)
Weight
Packing
Notes:
1.
2.
3.
4.
5.
max.
Unit
Condition
50
150
50.000/100.000/106.500/
125.000/132.000/141.000
MHz
MHz
±300
ppb
VC @ VREF/2
steady state
±10
±10
±10
±2
±500
±200
ppb
ppb
ppb
ppb
ppb
ppb
VREF
ppm
ppm
V
VS ± 5 %
RL ±5 %
AT-Cut
SC-Cut
AT-Cut
SC-Cut
Option 4
Option 4 = “T”
Option 4 = “U”
Option 4 = “U”
Option 4 = “U”
Option 4 = “U”
Option 1
Frequency stability
Initial tolerance @ +25°C
vs. operating temperature range
vs. supply voltage variation (pushing)
vs. load change (pulling)
Long term (aging) per day
(after 30 days operation) (Note 2)
st
Long term (aging) 1 year
(after 30 days operation) (Note 2)
Frequency adjustment range
Mechanical Frequency Control (EFC)
Electronic Frequency Control (EFC)
EFC voltage VC
EFC slope (∆f / ∆VC)
EFC input impedance
RF output
Signal waveform
Load RL
Output level (Note 3)
Harmonics
Spurious
Warm-up time @ +25°C
Phase Noise
Reference voltage VREF output (Note 4)
Supply voltage VS (Note 4)
Current consumption (steady state)
Current consumption (warm-up)
typ.
Option 2 & 3
See tables 2 & 3
±300
±50
See table 5
±1
±1
0
VREF/2
Positive
100
kΩ
See table 1
Sine wave
50
+7
11.4
-30
-90
3
5
Consult factory
10.0
12.0
12.6
150
350
51.0x51.0x20.5max.
70
Ω
dBm
dBc
dBc
min
V
V
mA
mA
mm
g
±5%
∆ffinal/f0 < ±0.1 ppm
@ +25°C (Note 5)
(Note 5)
IEC 60679-3 CO 40
Palette
Terminology and test conditions are according to IEC60679-1 and MIL-PRF-55310, unless otherwise stated
Lower aging on request
Other output level on request
Other supply and reference voltage on request
May be higher for wide operating temperature range
GmbH & Co. KG
Roemerring 9
D-74821 Mosbach
Germany
AXIOM55 Rev.4
Drawing D0
Page 1(4)
www.axtal.com
fon: +49 (6261) 939834
fax: +49 (6261) 939836
E-mail: [email protected]
Designed and
Manufactured
in Germany
Absolute Maximum Ratings
Parameter
min.
max.
Supply Voltage VS
Control Voltage VC
Storage Temperature
-0.5
-0.5
-55
VS + 10%
15
+125
Unit
Condition
V
V
°C
VS to GND
VC to GND
RF connector
Option 1
RF connector
_ (blank)
Pin 3
S
SMA connector
Table 1
Frequency stability vs. temperature
Option 2
05
10
25
50
100
200
Table 2
Stability
[ppb]
±5
±10
±25
±50
±100
±200
Lower Temperature
Option 3
T [°C]
0
0
1
-10
2
-20
3
-30
4
-40
5
-55
Table 3
Upper Temperature
Option 3
T [°C]
A
+50
B
+60
C
+70
D
+75
E
+80
F
+85
Standard: “1B” = -10°C to +60°C
Temperature
Frequency stability [Option 2]
range [°C]
05
10
25
50
100
200
0 ~ +50
O
SC
SC
SC
AT
AT
-10 ~ +60
O
SC
SC
SC
SC
AT
-20 ~ +70
O
SC
SC
SC
SC
SC
-30 ~ +70
O
SC
SC
SC
SC
SC
-40 ~ +75
O
SC
SC
SC
SC
-40 ~ +85
O
O
SC
SC
SC
-55 ~ +85
O
SC
SC
SC
Table 4 “Availability” AT, SC = AT-Cut, SC-Cut available, O = available on request, - not available
Frequency control
Option 4
Frequency control
_ (blank) No Frequency Control
T
Internal Trimmer
U
Control Voltage
Table 5
Ordering Code
Option 1
Option 2
Option 3
[RF connector] [Stability] [Temperature range]
AXIOM55
Table 1
Table 2
Table 3
Example: AXIOM55-S-100-1B-U_Rev.4 – 100.000 MHz
Model
GmbH & Co. KG
Roemerring 9
D-74821 Mosbach
Germany
AXIOM55 Rev.4
Drawing D0
Page 2(4)
Option 4
Revision
[Frequency control]
Table 5
Rev.4
Frequency
[MHz]
100.000
www.axtal.com
fon: +49 (6261) 939834
fax: +49 (6261) 939836
E-mail: [email protected]
Designed and
Manufactured
in Germany
Enclosure drawing
SMA connector
Option 1 = “S” only
Trimmer
Option 4 = “T” only
Pin connections
Pin #
1
Symbol
VC
Function
Control Voltage (EFC)
(Option 4 = “U” only, otherwise not connected)
2
3
VREF Reference Voltage
RF OUT RF Output
(Option 1 = _ (blank) only, otherwise not connected)
4
5
SMA
GND
Ground
VS
Supply Voltage
RF OUT RF Output
(Option 1 = “S” only, otherwise not installed)
GmbH & Co. KG
Roemerring 9
D-74821 Mosbach
Germany
AXIOM55 Rev.4
Drawing D0
Page 3(4)
* See Application Note AXAN-011
www.axtal.com
fon: +49 (6261) 939834
fax: +49 (6261) 939836
E-mail: [email protected]
Designed and
Manufactured
in Germany
Handling and Testing
Parameter
Procedure
Handling and Testing
Processing
Source
Application Note AXAN-011
Application Note AXAN-012
Parameter
Procedure
Electrostatic discharge (ESD)
THD devices
SMD devices
Washable
RoHS- Compliant
IEC60749-26
IEC60749-27
Yes
Yes
www.axtal.com
www.axtal.com
Condition
HBM
MM
No
No
2000 V
200 V
Environmental conditions
Test
Sealing tests
(if applicable)
Solderability
Resistance to
soldering heat
Shock*
IEC
60068
Part …
2-17
IEC
60679-1
Clause
5.6.2
MIL-STD202G
Method
112E
2-20
2-58
5.6.3
208H
210F
2-27
5.6.8
213B
Vibration,
2-6
5.6.7.1
201A
sinusoidal*
204D
Vibration,
2-64
5.6.7.3
214A
random*
Endurance tests
108A
- ageing
5.7.1
- extended aging
5.7.2
Other environmental conditions on request
MIL-STD810F
Method
MIL-PRF55310D
Clause
3.6.1.2
3.6.52
3.6.48
516.4
3.6.40
516.4-4
3.6.38.1
3.6.38.2
3.6.38.3
3.6.38.4
514.5
4.8.35
Test conditions (IEC)
Gross leak: Test Qc,
Fine leak: Test Qk
Test Ta Method 1
Test Td1 Method 2
Test Td2 Method 2
Test Ea, 3 x per axes 100g,
6 ms half-sine pulse
Test Fc, 30 min per axes,
10 Hz - 55 Hz 0,75mm; 55 Hz - 2 kHz, 10g
Test Fdb
30 days @ 85°C, OCXO @25°C
1000h, 2000h, 8000h @85°C
Data sheet is for information purposes only and may be subject to modifications or may be discontinued without notice.
Revision History
Rev.
Drawing
Date
[dd.mm.yyyy]
3
4
D0
D0
14.10.2013
18.04.2014
GmbH & Co. KG
Roemerring 9
D-74821 Mosbach
Germany
Remarks
Major revision
Frequency range changed, various parameters updated,
environmental conditions updated, editorial changes
AXIOM55 Rev.4
Drawing D0
Page 4(4)
Author
Checked
CG
HH
BN
HH
www.axtal.com
fon: +49 (6261) 939834
fax: +49 (6261) 939836
E-mail: [email protected]