A pp li c at i on N ot e , R ev . 2. 0 , D ec . 2 00 7 A p p li c a t i o n N o t e N o . 0 6 7 G e n e r a l P ur p o s e W i de B an d D r i v er A m p l i f i e r u s i n g B G A 61 4 R F & P r o t e c ti o n D e v i c e s Edition 2007-01-04 Published by Infineon Technologies AG 81726 München, Germany © Infineon Technologies AG 2009. All Rights Reserved. LEGAL DISCLAIMER THE INFORMATION GIVEN IN THIS APPLICATION NOTE IS GIVEN AS A HINT FOR THE IMPLEMENTATION OF THE INFINEON TECHNOLOGIES COMPONENT ONLY AND SHALL NOT BE REGARDED AS ANY DESCRIPTION OR WARRANTY OF A CERTAIN FUNCTIONALITY, CONDITION OR QUALITY OF THE INFINEON TECHNOLOGIES COMPONENT. THE RECIPIENT OF THIS APPLICATION NOTE MUST VERIFY ANY FUNCTION DESCRIBED HEREIN IN THE REAL APPLICATION. INFINEON TECHNOLOGIES HEREBY DISCLAIMS ANY AND ALL WARRANTIES AND LIABILITIES OF ANY KIND (INCLUDING WITHOUT LIMITATION WARRANTIES OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS OF ANY THIRD PARTY) WITH RESPECT TO ANY AND ALL INFORMATION GIVEN IN THIS APPLICATION NOTE. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. Application Note No. 067 Application Note No. 067 Revision History: 2007-01-04, Rev. 2.0 Previous Version: 2000-02-03 Page Subjects (major changes since last revision) All Document layout change Trademarks SIEGET® is a registered trademark of Infineon Technologies AG. Application Note 3 Rev. 2.0, 2007-01-04 Application Note No. 067 General Purpose Wide Band Driver Amplifier using BGA614 1 General Purpose Wide Band Driver Amplifier using BGA614 Features Easy to use, versatile, cascadable 50 Ω gain block - no external RF matching required • Unconditionally stable • Compression Point P1dB: +12 dBm • Exceptional noise figure for a low-cost, matched, broadband device: less than 2.4 dB at 2 GHz • 70 GHz fT SiGe technology Applications • RF amplifier for GSM, PCS, CDMA and UMTS basestations • Broadband amplifier for SAT-TV, CATV and LNBs • In, 1 3 4 2 1 4, GND GND, 2 3, Out Top View AN067_Pin_Cconnection.vsd Figure 1 PIN configuration 1.1 Introduction Infineon Technologies’ BGA614 is a matched, general purpose broadband MMIC amplifier in a Darlington configuration. It is implemented in Infineon’s high fT, low noise B7HF Silicon Germanium technology. The device’s 3 dB bandwidth covers DC up to 2.7 GHz with a typical gain of 18.5 dB at 1 GHz. The BGA614 is matched to 50 Ω and is unconditionally stable over the entire frequency range. At a device current of 40 mA the MMIC has an output 1 dB compression point of +12 dBm. At this same DC operating point, the noise figure is only 2.3 dB at 2 GHz - a value previously unheard of in a low-cost, 50 Ω matched gain block. This exceptional performance, enabled by Infineon’s 70 GHz B7HF Silicon Germanium process, combined with reduced external component count and ease of use make BGA614 an ideal choice for a wide variety of RF applications up to 2.5 GHz. The BGA614’s simplicity, flexibility and ease of use streamlines the wireless design process and allows for shorter design cycles and fast to time-to-market in today’s fast-paced, competitive business environment. Application Note 4 Rev. 2.0, 2007-01-04 Application Note No. 067 General Purpose Wide Band Driver Amplifier using BGA614 Out In GND AN067_equivalent_circuit.vsd Figure 2 Equivalent Circuit of BGA614 C1 100pF In 1 4 Q1 BGA614 C2 100pF 2 Out 3 L1 47nH Vcc R1 62Ω C3 100pF AN067_schematic.vsd Figure 3 Schematic Diagram Table 1 Bill of Materials Name Value Unit Size Manufacturer Function C1 100 pF 0402 Various DC block C2 100 pF 0402 Various DC block C3 100 pF 0402 Various RF bypass L1 47 nH 0402 Toko LL 1005-FH RF block R1 62 Ω 0402 Various Biasing IC1 BGA614 SOT343 Infineon Technologies SiGe MMIC Application Note 5 Rev. 2.0, 2007-01-04 Application Note No. 067 General Purpose Wide Band Driver Amplifier using BGA614 0.2 mm FR4 35 µm Cu 35 µm Cu for mechanical rigidity of PCB 0.8 mm FR4 35 µm Cu AN067_PCB_cross_section.vsd Figure 4 PCB Cross Section Table 2 Performance Overview Parameter Value 1.7 GHz 1.95 GHz 2.2 GHz Supply voltage VCC 5V 5V 5V Supply current ID 41.2 mA 41.2 mA 41.2 mA Gain 17.0 dB 16.5 dB 15.9 dB Noise figure 2.38 dB 2.35 dB 2.32 dB Input return loss 15.5 dB 14.5 dB 13.7 dB Output return loss 17.7 dB 16.8 dB 16.0 dB Reverse Isolation 21.1 dB 20.9 dB 20.6 dB Output P1dB 12.6 dBm 12.2 dBm 12.6 dBm 1) 23.6 dBm 21.0 dBm 20.8 dBm Output IP3 1) ∆f = 1 MHz; -20 dBm per tone 1.2 Circuit Design This application note describes the design of a general purpose broadband driver amplifier for the frequency band between 1.7 GHz and 2.2 GHz using the BGA614. This band covers the Tx as well as Rx frequencies of various standards from GSM1800 or DCS1800, North America PCS band, up to W-CDMA. Implementing an amplifier circuit using BGA614 is a simple, straightforward task. As both input and output are already matched to 50 Ω and BGA614 is an unconditionally stable device, there is no need to work on the RF portion of the amplifier design, leaving only DC biasing issues to contend with. The broadband 50 Ω match also eases and speeds integration of the MMIC with any external filters used. Figure 5 shows the component placement on the application PCB. There are only five external components necessary for the complete amplifier circuit. The low external parts count simplifies manufacturing issues and reduces required PCB area and associated costs. Application Note 6 Rev. 2.0, 2007-01-04 Application Note No. 067 General Purpose Wide Band Driver Amplifier using BGA614 In 1 C1 4 5 mm Q1 3 C2 Out L1 NA C4 2 R1 7 mm Vcc AN067_PCB_component_placement.vsd Figure 5 PCB: Component Placement The BGA614 is biased via its RF output pin (Pin 3). Figure 6 shows the dependence of the device current on the supply voltage for different values of the bias resistor R1. R1 stabilizes the supply current by using voltage feedback. In principle it is possible to bias BGA614 without an additional resistor. However, omitting R1 will lead to increased unit-to-unit variation in operating current due to the usual variation in the DC Beta (hFE) of the internal transistor cells. It is therefore recommended that R1 be used in all cases. 80 0Ω 16Ω 27Ω 70 47Ω 60 ID [mA] 50 68Ω 40 30 100Ω 20 150Ω 10 0 0 1 2 3 4 5 6 Vcc [V] AN067_ID(VDD).vsd Figure 6 Device Current vs. Supply Voltage, Parameter is R1 The inductor L1 in series with resistor R1 is necessary for RF blocking. C4 serves as a RF bypass at the voltage supply. The capacitors C1 and C2 are DC blocks as there is DC voltage present on Pin 1 as well as on Pin 3. These capacitors are needed only if there is no DC open circuit on the input and output of the amplifier. For example, if Application Note 7 Rev. 2.0, 2007-01-04 Application Note No. 067 Measurement Results a filter that presents a DC open circuit is used ahead of or after the BGA614, the corresponding DC blocking capacitor may be omitted. 1.3 Remarks BGA614 is only one member of Infineon Technologies’ broadband Darlingtion MMIC amplifier family. The complete family consists of BGA612, BGA614 and BGA616 to cover a wide range to typical supply currents. BGA612 is designed for a typical supply current of 20 mA, BGA614 for 40 mA and the BGA616 for 60 mA. The BGA614 application PCB can be used to evaluate BGA612 and BGA616 as well. It is only necessary to change the value of R1 to adjust the devices’ supply current accordingly. Typical values of R1 are 135 Ω at VCC = 5 V for BGA612 and 33 Ω at VCC = 6 V for BGA616. For further and more detailed dependencies of the devices’ supply currents please refer to the appropriate data sheets where graphs like the one in Figure 6 can be found for BGA612 and BGA616. 2 Measurement Results 18 Gain [dB] 17 16 15 14 13 12 1,7 1,8 1,9 2 2,1 2,2 Frequency [GHz] AN067_Gain(f).vsd Figure 7 Gain Application Note 8 Rev. 2.0, 2007-01-04 Application Note No. 067 Measurement Results Return Loss [dB] -10 -12 -14 s11 -16 s22 -18 -20 1,7 1,8 1,9 2 Frequency [GHz] Figure 8 2,1 2,2 A N067_Return_Loss(f).vsd Matching Noise Figure [dB] 3,6 3,2 2,8 2,4 2 1,6 1,7 1,8 1,9 2 2,1 2,2 Frequency [GHz] AN067_Noise_Figure(f).vsd Figure 9 Noise Figure Application Note 9 Rev. 2.0, 2007-01-04 Application Note No. 067 Measurement Results Reverse Isolation [dB] -15 -17 -19 -21 -23 -25 1,7 1,8 1,9 2 2,1 2,2 Frequeny [GHz] AN067_Reverse_Isolation(f).vsd Figure 10 Reverse Isolation 1,6 1,4 K, B1 1,2 K 1 0,8 0,6 B1 0,4 0,2 0 1 2 3 4 5 6 Frequency [GHz] A N067_K_B1(f).vsd Figure 11 Stability Factor Application Note 10 Rev. 2.0, 2007-01-04 Application Note No. 067 15 22 10 20 5 18 Gain 0 16 -5 14 -10 12 Pout -15 10 -30 -25 -20 -15 -10 -5 Pin [dBm] Figure 12 Gain [dB] Pout [dBm] Measurement Results 0 AN067_Pout(Pin).vsd Gain Compression 20 Gain [dB] 18 16 14 12 10 8 0 1 2 3 4 5 6 Frequency [GHz] AN067_wide_span_Gain(f).vsd Figure 13 Gain, wide span Application Note 11 Rev. 2.0, 2007-01-04 Application Note No. 067 Measurement Results Return Loss [dB] 0 -5 -10 s11 -15 s22 -20 -25 0 1 2 3 4 5 6 Frequency [GHz] AN067_wide_span_Return_loss(f).vsd Figure 14 Matching, wide span Application Note 12 Rev. 2.0, 2007-01-04