2.8X0.8mm RIGHT ANGLE SMD CHIP LED LAMP Features

2.8X0.8mm RIGHT ANGLE SMD CHIP LED
LAMP
ATTENTION
Part Number: AA2810AVW1S
White
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
Features
Descriptions
z 2.8mmX0.8mm right angle SMT LED, 1.2mm thickness.
z The source color devices are made with InGaN Light
Emitting Diode.
z Low power consumption.
z Ideal for backlight and indicator.
z Electrostatic discharge and power surge could damage
the LEDs.
z Package : 2000pcs / reel.
z Moisture sensitivity level : level 3.
z It is recommended to use a wrist band or antielectrostatic glove when handling the LEDs.
z RoHS compliant.
z All devices, equipments and machineries must be
electrically grounded.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.1(0.0039") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAK2447
REV NO: V.4B
DATE: AUG/30/2013
PAGE: 1 OF 7
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Y.Liu
ERP: 1201005944
Handling Precautions
Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic
significantly reduces thermal stress, it is more susceptible to damage by external mechanical force.
As a result, special handling precautions need to be observed during assembly using silicone encapsulated
LED products. Failure to comply might lead to damage and premature failure of the LED.
1. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry.
2. As silicone encapsulation is permeable to gases, some corrosive substances such as H2S might corrode silver plating of
leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances.
SPEC NO: DSAK2447
REV NO: V.4B
DATE: AUG/30/2013
PAGE: 2 OF 7
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Y.Liu
ERP: 1201005944
Selection Guide
Part No.
Dice
AA2810AVW1S
Iv (mcd) [2]
@ 20mA
Lens Type
White (InGaN)
Water Clear
Viewing
Angle [1]
Min.
Typ.
2θ1/2
1000
1400
110°
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity/ luminous Flux: +/-15%.
3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Device
VF [1]
Forward Voltage
White
IR
Reverse Current
White
X [2]
Typ.
Max.
Units
Test Conditions
3.3
4.0
V
IF=20mA
50
uA
VR = 5V
pF
VF=0V;f=1MHz
0.31
Chromaticity Coordinates
White
Y [2]
C
0.31
Capacitance
White
100
Notes:
1.Forward Voltage: +/-0.1V.
2. Measurement Tolerance Of The Chromaticity Coordinates Is ±0.01.
3.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
Absolute Maximum Ratings at TA=25°C
Parameter
White
Units
Power dissipation
120
mW
DC Forward Current
30
mA
Peak Forward Current [1]
100
mA
5
V
Reverse Voltage
Operating Temperature
-40°C To +85°C
Storage Temperature
-40°C To +85°C
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
SPEC NO: DSAK2447
REV NO: V.4B
DATE: AUG/30/2013
PAGE: 3 OF 7
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Y.Liu
ERP: 1201005944
White
AA2810AVW1S
SPEC NO: DSAK2447
REV NO: V.4B
DATE: AUG/30/2013
PAGE: 4 OF 7
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Y.Liu
ERP: 1201005944
AA2810AVW1S
White CIE
0.40
c0
0.35
y
b1
0.30
b2
a0
0.25
a2
0.20
0.20
0.25
0.30
0.35
0.40
x
a2
b1
x
y
x
y
x
y
0.263
0.213
0.282
0.245
0.298
0.271
0.282
0.245
0.298
0.271
0.313
0.296
0.265
0.265
0.286
0.299
0.306
0.332
0.242
0.226
0.265
0.265
0.286
0.299
0.313
0.296
0.329
0.325
0.329
0.325
0.358
0.372
0.329
0.371
0.363
0.400
0.306
0.332
0.329
0.371
a0
c0
b2
Notes:
Shipment may contain more than one chromaticity regions.
Orders for single chromaticity region are generally not accepted.
Measurement tolerance of the chromaticity coordinates is ±0.01.
SPEC NO: DSAK2447
REV NO: V.4B
DATE: AUG/30/2013
PAGE: 5 OF 7
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Y.Liu
ERP: 1201005944
AA2810AVW1S
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Reel Dimension
Tape Dimensions
(Units : mm)
SPEC NO: DSAK2447
REV NO: V.4B
DATE: AUG/30/2013
PAGE: 6 OF 7
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Y.Liu
ERP: 1201005944
PACKING & LABEL SPECIFICATIONS
AA2810AVW1S
Terms and conditions for the usage of this document
1.The information included in this document reflects representative usage scenarios and is intended
for technical reference only.
2.The part number, type, and specifications mentioned in this document are subject to future change
and improvement without notice. Before production usage customer should refer to the latest
datasheet for the updated specifications.
3.When using the products referenced in this document, please make sure the product is being
operated within the environmental and electrical limits specified in the datasheet. If customer usage
exceeds the specified limits, Kingbright will not be responsible for any subsequent issues.
4.The information in this document applies to typical usage in consumer electronics applications.
If customer's application has special reliability requirements or have life-threatening liabilities,
such as automotive or medical usage, please consult with Kingbright representative for further
assistance.
5.The contents and information of this document may not be reproduced or re-transmitted without
permission by Kingbright.
6.All design applications should refer to Kingbright application notes available at
http://www.KingbrightUSA.com/ApplicationNotes
SPEC NO: DSAK2447
REV NO: V.4B
DATE: AUG/30/2013
PAGE: 7 OF 7
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Y.Liu
ERP: 1201005944