1.6x0.8x0.5mm BI-COLOR SURFACE MOUNT LED Part Number: APHB1608QBDSURKC ATTENTION Blue Hyper Red OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Descriptions z 1.6mmX0.8mm SMT LED, 0.5mm thickness. z The Blue source color devices are made with InGaN z Compatible with reflow soldering. z Available in various color combination. Light Emitting Diode. z The Hyper Red source color devices are made with AlGaInP on GaAs substrate Light Emitting Diode. z Package: 2000pcs / reel . z Moisture sensitivity level : level 3. z Tinned pads for improved solderability. z Electrostatic discharge and power surge could damage the LEDs. z It is recommended to use a wrist band or anti- z RoHS compliant. electrostatic glove when handling the LEDs. z All devices, equipments and machineries must be electrically grounded. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.15(0.006") unless otherwise noted. 3.The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4.The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAK7907 REV NO: V.7A DATE: AUG/22/2014 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203011320 Selection Guide Part No. Dice Min. Typ. 40 70 *40 *70 120 250 *40 *90 Blue (InGaN) APHB1608QBDSURKC Viewing Angle [1] Iv (mcd) [2] @ 20mA Lens Type Water Clear Hyper Red (AlGaInP) 2θ1/2 130° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. * Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Blue Hyper Red λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 460 645 nm IF=20mA Blue Hyper Red 465 630 nm IF=20mA Spectral Line Half-width Blue Hyper Red 25 28 nm IF=20mA C Capacitance Blue Hyper Red 100 35 pF VF=0V;f=1MHz VF [2] Forward Voltage Blue Hyper Red 3.3 1.95 4 2.5 V IF=20mA IR Reverse Current Blue Hyper Red 50 10 uA VR = 5V Notes: 1.Wavelength: +/-1nm. 2.Forward Voltage: +/-0.1V. 3.Wavelength value is traceable to the CIE127-2007 compliant national standards. 4.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Blue Hyper Red Units Power dissipation 120 75 mW DC Forward Current 30 30 mA Peak Forward Current [1] 150 185 mA Reverse Voltage 5 Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C V Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAK7907 REV NO: V.7A DATE: AUG/22/2014 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203011320 APHB1608QBDSURKC Blue SPEC NO: DSAK7907 REV NO: V.7A DATE: AUG/22/2014 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203011320 Hyper Red SPEC NO: DSAK7907 REV NO: V.7A DATE: AUG/22/2014 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203011320 APHB1608QBDSURKC Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAK7907 REV NO: V.7A DATE: AUG/22/2014 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203011320 PACKING & LABEL SPECIFICATIONS APHB1608QBDSURKC Terms and conditions for the usage of this document 1.The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2.The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3.When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4.The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5.The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6.All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAK7907 REV NO: V.7A DATE: AUG/22/2014 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203011320