T-1(3mm) BI-COLOR INDICATOR LAMP Part Number: WP3VEYW High Efficiency Red Yellow Features Descriptions z Uniform light output. z The High Efficiency Red source color devices are made with Gallium Arsenide Phosphide on Gallium Phosphide z Low power consumption. z 3 leads with one common lead. z Long life - solid state reliability. Orange Light Emitting Diode. z The Yellow source color devices are made with Gallium Arsenide Phosphide on Gallium Phosphide Yellow Light z RoHS compliant. Emitting Diode. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. SPEC NO: DSAF2641 REV NO: V.5A DATE: APR/06/2015 PAGE: 1 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1101003934 Selection Guide Part No. Dice Lens Type Viewing Angle [1] Iv (mcd) [2] @ 20mA Min. Typ. 15 40 *10 *30 10 15 *10 *15 2θ1/2 High Efficiency Red (GaAsP/GaP) WP3VEYW White Diffused Yellow (GaAsP/GaP) 60° Notes: 1. θ1 / 2 is the angle from optical centerline where the luminous intensity is 1 / 2 of the optical peak value. 2. Luminous intensity / luminous Flux: + / -15%. * Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength High Efficiency Red Yellow λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 627 590 nm IF=20mA High Efficiency Red Yellow 617 588 nm IF=20mA Spectral Line Half-width High Efficiency Red Yellow 45 35 nm IF=20mA C Capacitance High Efficiency Red Yellow 15 20 pF VF=0V;f=1MHz VF [2] Forward Voltage High Efficiency Red Yellow 2 2.1 2.5 2.5 V IF=20mA IR Reverse Current High Efficiency Red Yellow 10 10 uA VR = 5V Notes: 1. Wavelength: + / -1nm. 2. Forward Voltage: + / -0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter High Efficiency Red Yellow Units Power dissipation 75 75 mW DC Forward Current 30 30 mA Peak Forward Current [1] 160 140 mA Reverse Voltage 5 Operating / Storage Temperature V -40°C To +85°C Lead Solder Temperature [2] 260°C For 3 Seconds Lead Solder Temperature [3] 260°C For 5 Seconds Notes: 1. 1 / 10 Duty Cycle, 0.1ms Pulse Width. 2. 2mm below package base. 3. 5mm below package base. SPEC NO: DSAF2641 REV NO: V.5A DATE: APR/06/2015 PAGE: 2 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1101003934 WP3VEYW High Efficiency Red SPEC NO: DSAF2641 REV NO: V.5A DATE: APR/06/2015 PAGE: 3 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1101003934 Yellow SPEC NO: DSAF2641 REV NO: V.5A DATE: APR/06/2015 PAGE: 4 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1101003934 PACKING & LABEL SPECIFICATIONS WP3VEYW Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAF2641 REV NO: V.5A DATE: APR/06/2015 PAGE: 5 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1101003934 SPEC NO: DSAF2641 REV NO: V.5A DATE: APR/06/2015 PAGE: 6 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1101003934 SPEC NO: DSAF2641 REV NO: V.5A DATE: APR/06/2015 PAGE: 7 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1101003934