1.6X1.25mm BI-COLOR SMD CHIP LED LAMP Part Number: APTB1612YSGC-F01 Yellow Super Bright Green Features Descriptions z 1.6mmx1.25mm SMD LED, 0.65mm thickness. z The Yellow source color devices are made with Gallium z Bi-color, low power consumption. Arsenide Phosphide on Gallium Phosphide Yellow Light Emitting Diode. z Wide viewing angle. z Ideal for backlight and indicator. z The Super Bright Green source color devices are made with Gallium Phosphide Green Light Emitting Diode. z Package : 2000pcs / reel. z Moisture sensitivity level : level 3. z RoHS compliant. Package Dimensions YELLOW GREEN Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.2(0.008") unless otherwise noted. 3.The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4.The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAE7243 REV NO: V.10B DATE: SEP/01/2015 PAGE: 1 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: F.T.Liu ERP: 1203002074 Selection Guide Part No. Emitting Color (Material) Lens Type Yellow (GaAsP/GaP) APTB1612YSGC-F01 Water Clear Super Bright Green (GaP) Viewing Angle [1] Iv (mcd) [2] @ 20mA Min. Typ. 3 8 5 12 2θ1/2 120° Notes: 1.θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2.Luminous intensity/ luminous Flux: +/-15%. 3.Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Emitting Color Typ. λpeak Peak Wavelength Yellow Super Bright Green λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 590 565 nm IF=20mA Yellow Super Bright Green 588 568 nm IF=20mA Spectral Line Half-width Yellow Super Bright Green 35 30 nm IF=20mA C Capacitance Yellow Super Bright Green 20 15 pF VF=0V;f=1MHz VF [2] Forward Voltage Yellow Super Bright Green 2.1 2.2 2.5 2.5 V IF=20mA IR Reverse Current Yellow Super Bright Green 10 10 uA VR = 5V Notes: 1.Wavelength: +/-1nm. 2.Forward Voltage: +/-0.1V. 3.Wavelength value is traceable to the CIE127-2007 compliant national standards. 4.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Yellow Super Bright Green Units Power dissipation 75 62.5 mW DC Forward Current 30 25 mA Peak Forward Current [1] 140 140 mA Reverse Voltage 5 V Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAE7243 REV NO: V.10B DATE: SEP/01/2015 PAGE: 2 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: F.T.Liu ERP: 1203002074 APTB1612YSGC-F01 Yellow SPEC NO: DSAE7243 REV NO: V.10B DATE: SEP/01/2015 PAGE: 3 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: F.T.Liu ERP: 1203002074 Super Bright Green SPEC NO: DSAE7243 REV NO: V.10B DATE: SEP/01/2015 PAGE: 4 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: F.T.Liu ERP: 1203002074 APTB1612YSGC-F01 Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAE7243 REV NO: V.10B DATE: SEP/01/2015 PAGE: 5 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: F.T.Liu ERP: 1203002074 PACKING & LABEL SPECIFICATIONS APTB1612YSGC-F01 Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAE7243 REV NO: V.10B DATE: SEP/01/2015 PAGE: 6 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: F.T.Liu ERP: 1203002074