T-1 (3mm) BI-LEVEL LED INDICATOR Part Number: WP130WCP/2GYW Green Yellow Features Descriptions z Bi-level right angle housing LED. z The Green source color devices are made with Gallium z Pre-trimmed leads for pc board mounting. z Black case enhances contrast ratio. Phosphide Green Light Emitting Diode. z The Yellow source color devices are made with Gallium z High reliability. Arsenide Phosphide on Gallium Phosphide Yellow Light z Housing UL rating:94V-0. Emitting Diode. z Housing material: type 66 nylon. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. SPEC NO: DSAF1892 REV NO: V.6B DATE: MAR/16/2015 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1102000167 Selection Guide Part No. Dice Green (GaP) WP130WCP/2GYW Viewing Angle [1] Iv (mcd) [2] @ 20mA Lens Type Min. Typ. 18 40 10 20 White Diffused Yellow (GaAsP/GaP) 2θ1/2 60° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. 3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Green Yellow λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 565 590 nm IF=20mA Green Yellow 568 588 nm IF=20mA Spectral Line Half-width Green Yellow 30 35 nm IF=20mA C Capacitance Green Yellow 15 20 pF VF=0V;f=1MHz VF [2] Forward Voltage Green Yellow 2.2 2.1 2.5 2.5 V IF=20mA IR Reverse Current Green Yellow 10 10 uA VR = 5V Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. 4. Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Green Yellow Units 62.5 75 mW DC Forward Current 25 30 mA Peak Forward Current [1] 140 140 mA Power dissipation Reverse Voltage 5 Operating / Storage Temperature V -40°C To +85°C Lead Solder Temperature [2] 260°C For 3 Seconds Lead Solder Temperature [3] 260°C For 5 Seconds Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. 2mm below package base. 3. 5mm below package base. SPEC NO: DSAF1892 REV NO: V.6B DATE: MAR/16/2015 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1102000167 WP130WCP/2GYW Green SPEC NO: DSAF1892 REV NO: V.6B DATE: MAR/16/2015 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1102000167 Yellow SPEC NO: DSAF1892 REV NO: V.6B DATE: MAR/16/2015 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1102000167 PACKING & LABEL SPECIFICATIONS WP130WCP/2GYW Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAF1892 REV NO: V.6B DATE: MAR/16/2015 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1102000167 SPEC NO: DSAF1892 REV NO: V.6B DATE: MAR/16/2015 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1102000167