2.8X0.8mm RIGHT ANGLE SMD CHIP LED LAMP Part Number: AA2810ASURSK Hyper Red Features Description z 2.8mmX0.8mm right angle SMT LED, 1.2mm thickness. The Hyper Red source color devices are made with Al- z Low power consumption. GaInP on GaAs substrate Light Emitting Diode. z Ideal for backlight and indicator. z Various colors and lens types available. z Package : 2000pcs / reel. z Moisture sensitivity level : level 3. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.0039") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAK2444 REV NO: V.5A DATE: OCT/15/2013 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201005912 Handling Precautions Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more susceptible to damage by external mechanical force. As a result, special handling precautions need to be observed during assembly using silicone encapsulated LED products. Failure to comply might lead to damage and premature failure of the LED. 1. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry. 2. As silicone encapsulation is permeable to gases, some corrosive substances such as H2S might corrode silver plating of leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances. SPEC NO: DSAK2444 REV NO: V.5A DATE: OCT/15/2013 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201005912 Selection Guide Part No. Dice AA2810ASURSK Iv (mcd) [2] @ 20mA Lens Type Hyper Red (AlGaInP) Min. Typ. 150 300 *40 *100 Viewing Angle [1] 2θ1/2 110° Water Clear Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. *Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Hyper Red λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 645 nm IF=20mA Hyper Red 630 nm IF=20mA Spectral Line Half-width Hyper Red 28 nm IF=20mA C Capacitance Hyper Red 35 pF VF=0V;f=1MHz VF [2] Forward Voltage Hyper Red 1.95 2.5 V IF=20mA IR Reverse Current Hyper Red 10 uA VR=5V Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. Absolute Maximum Ratings at TA=25°C Parameter Hyper Red Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 185 mA 5 V Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAK2444 REV NO: V.5A DATE: OCT/15/2013 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201005912 Hyper Red AA2810ASURSK SPEC NO: DSAK2444 REV NO: V.5A DATE: OCT/15/2013 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201005912 AA2810ASURSK Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAK2444 REV NO: V.5A DATE: OCT/15/2013 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201005912 PACKING & LABEL SPECIFICATIONS AA2810ASURSK Terms and conditions for the usage of this document 1.The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2.The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3.When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4.The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5.The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6.All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAK2444 REV NO: V.5A DATE: OCT/15/2013 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201005912