1.6X0.8mm INFRARED EMITTING DIODE Part Number: AP1608SF4C Features Description z 1.6mmX0.8mm SMT LED, 1.1mm thickness. SF4 Made with Gallium Aluminum Arsenide Infrared Emit- z Mechanically and spectrally matched to the phototransistor. ting diodes. z Package: 2000pcs / reel. z Moisture sensitivity level : level 3. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.004") unless otherwise noted. 3.The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4.The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAA8462 REV NO: V.9 DATE: AUG/02/2011 PAGE: 1 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.HAN ERP: 1203000062 Selection Guide Part No. AP1608SF4C Dice Lens Type SF4 (GaAlAs) Po (mW/sr) [2] @ 20mA Viewing Angle [1] Min. Typ. 2θ1/2 0.8 1.5 120° Water Clear Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Radiant Intensity/ luminous flux: +/-15%. Electrical / Optical Characteristics at TA=25°C Parameter P/N Symbol Typ. Max. Units Test Conditions Forward Voltage [1] SF4 VF 1.3 1.6 V IF=20mA Reverse Current SF4 IR 10 uA VR = 5V Capacitance SF4 C 90 pF VF=0V;f=1MHz Peak Spectral Wavelength SF4 λP 880 nm IF=20mA Spectral Bandwidth SF4 Δλ1/2 50 nm IF=20mA Note: 1. Forward Voltage: +/-0.1V. Absolute Maximum Ratings at TA=25°C Parameter Symbol SF4 Units Power dissipation PD 80 mW DC Forward Current IF 50 mA Peak Forward Current [1] iFS 1.2 A Reverse Voltage VR 5 V Operating Temperature TA -40 To +85 °C TSTG -40 To +85 °C Storage Temperature Note: 1. 1/100 Duty Cycle, 10μs Pulse Width. SPEC NO: DSAA8462 REV NO: V.9 DATE: AUG/02/2011 PAGE: 2 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.HAN ERP: 1203000062 AP1608SF4C SPEC NO: DSAA8462 REV NO: V.9 DATE: AUG/02/2011 PAGE: 3 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.HAN ERP: 1203000062 AP1608SF4C Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Specifications (Units : mm) SPEC NO: DSAA8462 REV NO: V.9 DATE: AUG/02/2011 PAGE: 4 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.HAN ERP: 1203000062 PACKING & LABEL SPECIFICATIONS AP1608SF4C SPEC NO: DSAA8462 REV NO: V.9 DATE: AUG/02/2011 PAGE: 5 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.HAN ERP: 1203000062